ADE CONCEPT SYSTEM User Manual
once
C
r
f
3j.lrfem
CUSTOMER INSTRUCTIONS
TO SET SYSTEM
The
DAY
indicator should be showing. Enter
your code number. Check that the system is
clear (none of the zone indicators arc showing).
If
clear. the sounder will produce a bleep tone
and you may now leave by the correct route.
The system will set at the
system is not clear. the sounder will produce a
broken tone and the zone indicator will display
the fault. Either. enter your code to turn off
and investigate the cause of the fault, or omit
the faulty zone from the system.
TO UNSET THE SYSTEM
Enter your code,
has been activated) the unit will return to
DAY.
If the system has been activated. then
entering the code will turn off the sounders and
the cause of the alarm will be displayed. Press
RESET to clear the indication and return
DAY.
TO OMIT ANY ZONE FROM THE SYSTEM.
Starting from thc DAY modc. Enter code and
the exit time begins Press OMIT and the exit
tone will now change to an omit tone. Enter the
zone numbers you wish to omit e.g. pressing
then 4 will remove zoncs two and four from the
system. The zone two and four leds will flash to
show correct selection.
and a wrong zone number is pressed then press
0,
this will cancel the previous selection and
allow another zone to be omitted. When the
selection is correct press
return to exit modc and the timer will continue.
Thc maximum number
omitted at any one time is three.
(Turn on)
if
the system
If
of
end of exit time.
(Turn
off)
i\
clear (no alarm
you make a mistake
SET.
the unit will now
zones which may be
If
the
to
2
TO QUICK SET THE SYSTEM
During the exit time the system may be set
quickly by pressing SET. This removes the time
normally allowed for exit, and would be used
you are not leaving the premises.
part of the system and require quick set. press
SET
twice.
POWER INDICATORS
A
red power indicator should be showing at all
times. on both the power supply and the
keypad. If either indicator gocs out call the
engineer to check the system.
If
you omit
if
CUSTOMER PROGRAMMING
Customer code change. Alarm memory recall and Alarm tests arc all available from the cu\rorner program.
With the DAY light showing press the following
button\ In the correct sequence.
daQuJuu
Press PROG button All lights will show.
0
Enter vour code
DAY and TAMPER
lights show.
I
Press
Q
now enter
New CODE
(4
digits)
M>OO
AI
ARM MEMORY RECAU
Press PROG button All lights will bhow.
0
Enter your code
m
Four Zone indicators
show.
The unit will bleep
yt;;;;
again.
The new code is now
cntered into the
Concept memory.
DAY and TAMPER
lights show.
ALARM
Pres~
Enter your code
TFST
0
m
The unit is now in the
Press
Press
m
Press
m
All Ilght. u11l \how
DAY and TAMPER
lights show.
DAY. TAMPER
ATTACK Ilghts shou
te\t program
1'0
test the Strobe
(cont~nues until
pressed).
To test the Oulstde
Sounder (continues
0
is pressed).
until
To test Low Sounder
(continues until
pressrd).
To test High Volume
Sounder (continues
until
0
is
pressed).
dnd
0
is
0
i\
Press
MEM
0
buttolr
to return to
The last alarm will
now be displayed for
5
seconds. The
system will bleep
and return to
program.
DAY.
ruice
T'o
cnter walk test.
Internal Sounder ulll
nou operate each
tlrnc a zone
opened
0
I.;
pressed).
to rt.turr1
15
(continues
ro
DA
1'
unt~l
rnotle.
Loading...