Addonics Technologies HDUS11325DX User Manual

T E C H N O L O G I E S

Target Drive Bay 1 - 5

Source Drive Bay

Target Drive Bay 6 - 11

ENT

ESC

Duplicator Panel

Power Switch

User Guide

1:11 HDD Duplicator Deluxe

(HDUS11325DX)

www.addonics.com

v3.1.11

Technical Support

If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST
Phone: [phone]
Email: http://www.addonics.com/support/query/

Table Of Contents

Basic Instructions

Functions

Copy HDD

Compare HDD

PreScan Source

ReScan Bus

Source Size

Overwrite

Setup

Advanced Setup

Basic Troubleshooting

Error Messages List

Firmware Update Procedure

............. Page 3

............. Page 5

............. Page 6

............. Page 6

............. Page 7

............. Page 8

............. Page 8

............. Page 9

............. Page 9

............. Page 13

............. Page 16

............. Page 17

............. Page 18

Basic Instructions

I. Installing Drive into the HDD Duplicator

For installing a hard drive on the various enclosures that come with the HDD duplicator, refer to the
bundled enclosure installation guides.

Step 1

Open the source drive door and slide in the 3.5” SATA hard disk Source drive into the drive bay. Close the
front panel and using the key provided, turn the key lock to the Lock position. This will secure the drive and
turn on the power to the hard drive.

Step 2

Open the target drive door(s) and slide in the 3.5” SATA hard disk Target drive(s) into the drive bay. Close
the front panel and using the key provided, turn the key lock to the Lock position. This will secure the drive
and turn on the power to the hard drive.

Note: Refer to the Snap-In 25

user guide for 2.5” SATA hard drive installation.

II. Connecting the Power Cable and Powering On

a. Connect the power cord provided f rom t he wall outlet to t he back of the tower.

b. A main power switch is located at the back of the tower. Turn the switch on. Another auxiliary

switch is located on the front of the tower.

c. Push the auxiliary switch button to t urn on the HDD duplicator.

III. The Duplicator P anel

There are four buttons and an LCD on the panel of HDD Duplicator.
1 – LCD shows a f unction or a message.
2 – it is used to scroll up function menus.
3 – it is used to scroll down function menus.
4 – it is used to execute a f unction.
5 – it is used to cancel a function.

Duplicator P anel

ENT

ESC

1
2

4
5

3

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/

IV. Duplicating a drive

When the duplicator powers on, it initializes and goes through the steps below
Shows the firmware version Initialize SDRAM's status..

HD Duplicator

1-1 Ver:

Detect Drives' status. Shows the first function:

Detect Drives

Copy HDD copies data directly from t he source hard disk to t he t arget hard disk.
Press ENT button to begin copy. The system will auto-detect the hard disks and show the following info on

the LCD.

Copy-36MBs 0%

235.7GB 1:48

The LCD will show the following info during the copying process: remaining time, completed percentage.
The copy speed, capacity and time will vary depending on the source hard disk. Once the copying process
is complete t he LCD will display t he f ollowing results.

Copy HD
OK:

Initialize S DRAM

1.Copy HD

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/

Functions

The copy controller has 11 functions in total, with the 11
function that only appears when the ESC key is pressed fo
are shown below.

Duplicator Controller

10-01. Language
10-02. Copy Size
10-03. Startup Menu
10-04. Auto Compare
10-05. Button Sound
10-06. Device Info

10. Setup

10-07. System Info
10-08. Fast Copy
10-09. Auto Start Drive
10-10. Auto Start Timer

10-11. Tolerance Size
10-12. BootTime Delay

10-13. Quick Compare

11. Adv Setup

th (Adv Setup) being a hidden system

r 2 seconds until there is a beep. These

1. Copy HDD

2. Async Copy HDD

3. Compare HDD

4. Async Compare

5. PreScan Source

6. ReScan BUS

7. Source Size

8. Secure Erase

9. Overwrite

10. Setup

11. Adv Setup

11-01. Read Error Skip

11-02. Update Firmware
11-03. Compare Firmware
11-04. Quick Erase HDD

11-05. Full Erase HDD
11-06. H/W Diagnostic
11-07. Load Default

11-08. Copy HPA

11-09. Burn In

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/

Copy HDD

Copy HDD copies data directly from the source hard disk to

the target hard disk. Please make

sure that the capacity of the target hard disk is equal o

r larger than the source hard disk.

Choose option 1 from the menu:

Press ENT to begin copy. The system will auto-detect the hard di

sks and show the following

copying info on the LCD.

The LCD will show the following info during the copyin

g process: elapsed time, completed

percentage. The copy speed, capacity and time will vary

depending on the source hard disk. Once

the copying process is complete the LCD will display t

he following results.

Copy-36MB/s 0%

232.9GB 00:00:00

Copy HDD
OK: 11 Fail: 0

1. Copy HDD
HDD:11 232.9GB

Async Copy HDD

This option is used to specify the size of the source for simplifying further copying operations.
Choose option 2 from the menu:

2. Async Copy HDD
HDD:10 232.9GB

Press ENT . Before the start of the reproduction, if the console detects that a hard drive
capacity is less than source, then the LCD will show the cor

responding channel number.

8
Space Not Enough

And then automatically copies. The LCD will display t

he following info.

Acpy-36MB/s 0%

232.9GB 00:00:00

If the replication process to continue to add additi

onal hard disk device, LCD will only show the last

completed percentage.
Once the copying process is complete the LCD will disp

lay the following results.

Async Copy HDD
OK: 11 Fail: 0

Compare

Compare HDD is used to see if the data on a source ha

rd disk is identical to the target hard disk

after the Copy HD operation.
Choose option 3 from the menu:

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/