Additel ADT 680 Operating Manual
ADT 680 Digital Pressure Gauge
User's Manual
[.：]Version No 1612V14
Additel Corporation
Digital Pressure Gauge
CONTENTS
1. Introduction
2. Basic structure
3. 2
Keypad
4. Display 3
5. Start-up screen
6. Menu setup and configuration
7. Calibration
8. Troubleshooting
9. ….……….………………………………………………………………………………………………Custom Unit Entry 13
Specifications 15
. …...……………………………………………………….………………………………………………
10
1 Warning 19
1 . ………………………………………………………………………………………………………………
2 FCC Declaration of Conformity 20
1 . ……………………………………………………………………………………
3 Battery installation 22
1 . …………………………………………………………………………………………………
4 Ordering information 23
1 . ………………………………………………………………………………………………
……………………………………………………………………………………………………………1
…………………………………………………………………………………………………………1
…………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………
…………………………………………………………………………………………………………3
………………………………………………………………………………………4
………………………………………………………………………………………………………………8
………………………………………………………………………………………………………12
5 Appendix 24
1 . ………………………………………………………………………………………………
I– Data logging
1
Introduction
Digital Pressure Gauge
The ADT digital pressure gauge is a rugged wireless data logging pressure gauge that can log in real
, .
time or data which can be stored and downloade later via wireless communication The compact industrial
design and advanced technology makes the ADT as an ideal pressure measurement tool The ADT
combines a variety of accuracy levels with a robust IP water and dust proof casing It can
either as a pressure reference or an applications where high accuracy is required
Basic structure
2
680
units
psi
zero
d
Rubber boot
Model
Screen
keypad
Pressure Range
680 . 680
67 - - .
measurement
Back Plate Screws
Label Plate
be used
.
M20X1.5
Pressure Port Type
Sensor Cavity
Pressure Port
1
keypad
3
Digital Pressure Gauge
Pressure display:
Menu setup mode:
Pressure display:
Push the button Switch engineering units->
Push and hold the button Enter menu
Push the button Move forward
Push and hold the button Turns power
->
->
setup mode
through menus /
Highlight shift right
on off->/
units
Pressure display:
Menu setup mode:
zero
Pressure display:
Push the button Backlight on off-> /
Push and hold the button Min Max
Push the button Move backward
Push the button Pressure zero->
Push and hold the button Lock Unlock
->
through menus
Number incrementing
/
-> /
value
-> /
Key
Menu setup mode:
2
Push the button Go back Cancel-> /
Menu setup mode:
Push the button Enter Make selection-> /
Digital Pressure Gauge
Display
4
Start-up screen
5
Keypad lock icon
Data logging icon
Wireless signal icon
Battery bar graph
Absolute pressure
Engineering units
5 digit display
Percentage bar graph
Menu icons
Full screen display
Software version
Live pressure display
Upper range value
Lower range value
3
Digital Pressure Gauge
Menu setup and configuration
6
6.1 Menu structure
RTC
Rate
Auto off
Backlight time
Year
Month day:
Hour min:
Second
01.
03.
10.
15
15
30
45
60
90
120
OFF
15
30
45
60
ON
Pressure reading interval
unit second(: )
Delay time before auto off
unit minute(: )
Gauge does not auto off
Backlight auto off time
unit second(: )
Backlight does not auto off
03
04
Average filter
10
Average measure
4
1ORD
OFF
Low pass first order filter
(only active for 0.1 readings/second)
No filter
Digital Pressure Gauge
Extended units
in 20(℃)HO₂
in 60(℉)HO₂
mm 20(℃)HO₂
mm 15(℃)HO₂
ft 60(℉)HO₂
ft 4(℉)HO₂
Set factor for custom units Refer to specification()
Calibration
Utilities
Data logging
1cal.
2c00.-
3clr.
4 abs.
5dp01.-/
1.bat
2temp.
3 leak.
4fact.
51.-az
1cap.
2 send.
3 del.
4 gap.
5ct01.-/
6off.
Calibration See calibration section on page(8)
View overpressure records ( )Refer to specification
Cancel recover calibration data/
Cancel pressure zero
Tare setting Refer to specification Gauge() Absolute pressure zeroing Absolute-
Overpressure status: 1 means YES, 0 means NO.
Battery voltage
Environment temperature support(℃、℉)
Pressure leak test
Restore factory settings, “password is 218”
Auto zero
Memory capacity status
Upload data
Delete all data, password is “218”
Logging Interval s s(0001 -9999 )
Keep the logging status after restart
1 means YES, 0 means NO)(
Start Stop logging/
Wireless
1.off
2.chan
3 addr.
4ct01.-/
Wireless on off/
Wireless channel CH 01 15( -~)
Device address 001 112(~)
Keep the wireless status after restart
( 1 means YES, 0 means NO)
5
Digital Pressure Gauge
6.2 Menu operation
6.2.1 Enter Return/
Push and hold button in the pressure display mode to enter menu setup mode.
Push button in menu setup mode to return to previous menu.
Example:
units
Menu1
Pressure display
6.2.2 Switch menu item
Push and button to move forward or backward through the menus:
units
units
Push and hold
Push
Aver ge measure(a )
6
Loading...