HL-2
Heat Lamp
This manual contains important information regarding your
Admiral Craft unit. Please read this manual thoroughly prior to
equipment set-up, operation and maintenance. Failure to comply
with regular maintenance guidelines outlined in this manual may
void the warranty. MUST READ!!!
WARNINGS
Do not touch any hot surfaces
Do not immerse unit, cord or plug in liquid at any time
Unplug cord from outlet when not in use and before cleaning
Plug only into a 3-hole grounded electrical outlet
Do not operate unattended
Do not use this unit for anything other than intended use
Do not use outdoors
Always use on a firm, dry and level surface at least 12” from walls or any other obstruction
Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or has been damaged in any
manner
Keep children and animals away from unit
Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to property loss and injury.
All repairs should be done by authorized professionals only
Ensure that the designated power supply is adequate for continual usage and the voltage is correct
TO USE
1. Make sure the power supply you are using is adequate.
2. Set the unit on a flat sturdy surface
3. Install bulbs with the appropriate wattage rating as indicated on the warmer
4. Plug cord into a grounded electrical outlet of the correct voltage
5. Place food products in a pan, located directly under the bulbs for best results
6. When you finish using the unit, unplug it
7. To disconnect appliance, turn switch off and remove from power source
CLEANING - NOTE: To maintain cleanliness and increase service life, the heat lamp should be cleaned daily. Do not
immerse the unit in water or any other liquid, if liquid enters the unit it may cause a short circuit or electrical shock
1. Before cleaning or attempting to move the heat lamp, unplug and let the unit cool completely
2. Wipe the entire unit with a clean soft cloth and mild soap
3. To avoid damage, do not use abrasive cleaners or scouring pads
4. If soap or chemical cleaners are used, be sure they are completely rinsed away with clear water immediately
after cleaning. Chemical residue could damage or corrode the surfaces of the unit.
HL-2A
VER811
Dual Heat Lamp - HL-2
Reference
2 - Lamp Shade
3 - Socket Hardware
5 - Bulb
6 HL-6 Frame Caps
7 HL-7 On/Off Switch
10 HL-10 Wing Nut
11 - Base Frame
Number Part Number Description
1 - Upper Frame
4 HL-4 Porcelain Lamp Holder
9 HL-9 Power Cord and Strain Relief
12 HL-12 Rubber Foot and Screw
VER811
ACE Electrical
Equipment
One Year
Warranty
ACE warrants its equipment against defects in materials and workmanship, subject to the following
conditions: This warranty applies to the original owner only, and is not assignable.
ACE Electrical Equipment is warranted for one year, effective from the date of purchase by the original
owner. A copy of the original receipt or other proof of purchase is required to obtain warranty coverage.
Should any product fail to function in its intended manner under normal use within the limits defined
in this warranty, at ACE’s discretion, such product will be repaired, replaced with a refurbished unit, or
replaced with a new unit by ACE, after defective unit has been inspected and defect has been confirmed.
ACE does not assume any liability for extended delays in replacing any item beyond its control. This
warranty does not apply to rubber and non-metallic synthetic parts where usage, wear, or lack of
preventative maintenance may create abnormal replacement rates, and these parts are excluded from this
limited warranty.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, and metropolitan
areas of Alaska and Canada. Warranty coverage on products used outside the 48 contiguous United
States, Hawaii and metropolitan areas of Alaska and Canada may vary. Contact ACE for details at 1-800223-7750
The following conditions are not covered by
warranty:
•
Equipment failure relating to improper installation, improper utility connection or supply and
problems due to improper ventilation.
•
Equipment that has not properly been maintained, damage for improper cleaning, and water
damage to controls.
•
Equipment that has not been used in an appropriate manner, or has been subject to misuse,
neglect, abuse, accident, alteration, negligence, damage during transit, delivery or installation,
fire, flood, riot, or act of God.
•
Equipment that has the model number or serial number removed or altered.
•
Equipment on which the security seal has been broken.
If the equipment has been changed, altered, modified, or repaired without express written permission
from ACE, then the manufacturer shall not be liable for any damages to any person or to any property,
which may result from the use of this equipment thereafter.
This equipment is intended for commercial use only. Warranty is void if equipment is used in other
than a commercial application.
In the event your repair is not covered under the stated warranty provisions, parts are available by
calling 1-800-223-7750. Equipment not covered by repair should be picked up from our warehouse
facility within 10 business days from notification date. Any and all arrangements and expenses for the
return of this merchandise is your responsibility.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED
OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY OR FITNESS
FOR PARTICULAR PURPOSES AND CONSTITUES THE ENTIRE LIABILITY OF ACE. IN NO
EVENT DOES THE LIMITED WARRANTY EXTEND BEYOND THE TERMS STATED HEREIN.”
VER40111
Loading...