AcuRite 00536 User Manual
INST - 00536 082210
Wireless Thermometer
#00536
Instruction Manual
Package Contents:
(1) Main Unit (A)
(1) Wireless Sensor (B)
(1) Instruction Manual
What You Need:
• (4) AA batteries
A. Main UnitB. Wireless Sensor
Thank you for purchasing this ACURITE® product. Please read this manual in it’s entirety
to fully enjoy the benets and features of this product. Please keep this manual for
future reference.
NOTE: A clear lm is applied to the LCD at the factory that must be removed prior to
using this product. Locate the clear tab and simply peel to remove.
1 • OVERVIEW OF FEATURES
Boy / Girl
Selection
Boy / Girl
Weather
Character
Main Unit
LOW BATTERY
Indicator
Wireless Sensor
LOW BATTERY
Indicator
Outdoor
Temperature
Wireless Sensor
Signal Icon
Min / Max
Temperature
Thermometer
Scale
SECTION 2 • SETUP
Battery Choice & Temperature Range
Extended periods of cold temperatures ( below -4ºF / -20ºC ) can cause alkaline
batteries to function improperly. This will cause the outdoor wireless sensor to stop
transmitting temperature readings. Use lithium batteries in these low temperature
conditions to ensure continued operation for wireless sensors placed outdoors. NOTE:
Rechargeable batteries are not recommended due to higher operating voltages.
Install Batteries
NOTE: Install all batteries in both units within a 6 minute period to ensure proper
wireless functionality. Always install batteries into the wireless sensor FIRST.
A. Wireless Sensor
Remove the battery
compartment cover.
Install 2 fresh “AA”
batteries as shown
here.
REMOVE
BATTERY
COMPARTMENT
COVER
INSTALL 2 “AA”
BATTERIES
Basic Setup is Now Complete
The wireless sensor will soon send a signal to the main unit and the two units will
be synchronized. It may take a few minutes for synchronization to be complete.
The wireless sensor signal icon on the display will show 1 to 4 “bars” when the
signal is received. If both or one of the units appear to be functioning improperly,
refer to the troubleshooting section in this manual.
Main Unit : Time and Date Set
After installing batteries into the Wireless Sensor and into the Main Unit, the
units and character displayed can be set.
TO SET THE MAIN UNIT:
Press and hold the “SET” button for 5 seconds to enter into SET MODE.
Once in set mode, the preference you are currently setting will blink on the
display.
The preference set order is as follows:
UNITS: °F or °C
CHARACTER: boy or girl
To adjust the currently selected (ashing) preference item, press the “
buttons to adjust up to the desired setting (press and HOLD to fast adjust). To save
your adjustments, press the “SET” button again to move on to adjusting the next
preference.
” or “ ”
B. Main Unit
Remove the battery
compartment cover
and install 2 fresh “AA”
batteries as shown
here.
REMOVE
STAND AND
BATTERY
COMPARTMENT
COVER
Wireless Sensor
SET
Main Unit
INSTALL 2 “AA”
BATTERIES
You will automatically exit SET MODE if no buttons are depressed for 5 seconds. You
may enter basic setup mode again at any time by pressing and holding the “SET”
button.
Main Unit : MIN/MAX Memory
This wireless forecaster features a MIN/MAX memory feature which records the
MINIMUM and MAXIMUM outdoor temperature readings.
To view the MAX recorder temperature reading, press and release the “ ” button.
Note the “MAX” icon on the display.
To view the MIN recorder temperature reading, press and release the “ ” button.
Note the “MIN” icon on the display.
To clear the MAX recorded values, press and hold the “ ” button while in the MAX
view mode. The MAX value will clear daily at approximately the same time, coincident
with when the batteries were rst installed or when the unit was last cleared.
To clear the MIN recorded values, press and hold the “ ” button while in the MIN view
mode. The MIN value will clear daily at approximately the same time, coincident with
when the batteries were rst installed or when the unit was last cleared.
Loading...