Actiontec SBWD100A, SBT100U Installation Guide
Step
3 A new screen appears.
Select the Receiver, then
click Connect.
Step
4 A PIN appears on your
HDTV screen.
Step
5 Enter the PIN in the
ScreenBeam software application
within 60 seconds, then click Next.
The ScreenBeam Transmitter and
Receiver are now paired.
You should see the screen of the
laptop/PC on the HDTV.
For Wi-Fi Miracast or Intel WiDi Devices
• Wi-Fi Miracast: You can connect directly to the ScreenBeam
Receiver from a Windows 8.1 or Android 4.2 device.
Visit www.actiontec.com/wirelessdisplay for compatibility
and setup instructions.
• Intel WiDi: If your system can run Intel WiDi 3.5 (or higher),
you can also connect it directly to the ScreenBeam Receiver.
Visit www.intel.com/go/wirelessdisplayupdate to verify.
Go to www.actiontec.com/screenbeamkit for product support,
updates, and more information, including:
• Firmware • Troubleshooting • User Manual • FAQs
Frequently Asked Questions
ScreenBeam displays a screen that seems to be larger than my
TV can handle. How can I fix this?
Right-click the ScreenBeam icon in the Windows system tray, at the
bottom right of the desktop. A menu will appear. From the menu,
select Preferences, then adjust the screen size.
How can I update my Wireless Display Receiver firmware?
Go to http://www.actiontec.com/screenbeamkit to download
the latest rmware and refer to the upgrade instructions
posted online.
Do I need to install ScreenBeam software or the USB
Transmitter included with the ScreenBeam Kit to connect to a
Miracast or Intel WiDi device?
No. For Miracast devices, refer to the user guide of the device’s
manufacturer. For WiDi-capable systems, make sure your system
driver and WiDi software are updated to the latest revision.
I’m seeing a mosaic display on my HDTV. What should I do?
First, make sure the laptop/PC meets the recommended system
requirements. If you’re seeing a constant mosaic picture,
disconnect, then reconnect the ScreenBeam connection. Also,
make sure the Wireless Display Receiver is not hidden inside a
cabinet, as this can reduce performance.
I’ve inserted the software CD into the CD-ROM drive, but it
doesn’t install. What should I do?
In Windows Explorer, browse to the CD-ROM drive (e.g., D:), then
locate and double-click on the “Setup.exe” le.
Should I be concerned if Windows’ firewall or anti-virus
software warns that ScreenBeam is trying to open a port?
ScreenBeam requires Windows to temporarily open a port to
stream content to the TV. Click Allow when the message appears.
How can I update my ScreenBeam Wireless Display software?
Open the ScreenBeam Wireless Display application. Right-click
on the ScreenBeam Receiver you’ve previously connected to and
select “Check for updates…” . Make sure the laptop/PC is
connected to the Internet.
My laptop/PC displays the following message: “Color scheme
has been changed.” Is this a problem?
No. Select “Keep the current color scheme and don’t show this
message again.”
Why am I unable to play a DVD or Blu-ray disc when connected
to ScreenBeam?
Currently, ScreenBeam does not support the streaming of
protected content such as DVD/Blu-ray movies, TV shows, etc.
What should I do if the ScreenBeam Wireless Display software
cannot connect or pair with ScreenBeam Receiver?
Reboot the laptop and power cycle the ScreenBeam Receiver. Also,
try selecting a dierent wireless channel before connecting. To do
this, from the “Add a Receiver” screen, click on the wireless channel
drop-down menu, then select a dierent wireless channel.
Declarations of Conformity (DoC)
To obtain the complete DoC form in softcopy, go to the
Actiontec Electronics Declarations of Conformity EU/EEA website
at http://international.actiontec.com/support/doc
For GNU General Public License (GPL) related information, go to
http://opensource.actiontec.com
The symbol at right is placed in accordance with the European
Union Directive 2002/96 on the Waste Electrical and Electronic
Equipment (the WEEE Directive). If disposed of
within the European Union, this product should be
treated and recycled in accordance with the laws of
your jurisdiction implementing the WEEE Directive.
This product has a 1-year Limited Hardware Warranty and 90-day free software
updates from date of purchase.
Local Law
This Limited Warranty Statement gives the customer specic legal rights. The
customer may also have other rights which vary from state to state in the United
States, from province to province in Canada, and from country to country
elsewhere in the world.
To the extent that this Limited Warranty Statement is inconsistent with local law,
this Statement shall be deemed modied to be consistent with such local law.
Under such local law, certain disclaimers and limitations of this Warranty
Statement may not apply to the customer.
Go to http://www.actiontec.com/products/warranty.php for more information.
© 2013 Actiontec Electronics, Inc. ScreenBeam and the Actiontec logo are
registered trademarks or trademarks of Actiontec Electronics, Inc., in the U.S. or
other countries. All other names are properties of their respective owners.
Wireless
Display Kit
ScreenBeam
Model # SBWD100A & Model # SBT100U
Installation Guide
This Installation Guide will walk you through the easy steps
to set up your ScreenBeam Wireless Display Receiver and
USB Transmitter. During this process, we’ll show you how to:
Install the Receiver
A
Install the Software
B
and USB Transmitter
Pair the Receiver and
C
USB Transmitter
IMPORTANT: Federal Communication Commission (FCC) Radiation
Exposure Statement:
This EUT is compliance with SAR for general population/uncontrolled exposure
limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the
measurement methods and procedures specied in OET Bulletin 65 Supplement
C. This equipment should be installed and operated with minimum distance
1.5 cm between the radiator and your body.
Part # 0530-0683-002
NEXT
Welcome!
Congratulations on your purchase of a ScreenBeam Wireless
Display Kit. The Kit lets you wirelessly transmit content from your
compatible PC or Wi-Fi Miracast device to your HDTV.
Important! If you are using a Wi-Fi Miracast or Intel Wireless Display
(WiDi) device, complete Section A, “Install the Receiver,” only. To check
for device compatibility, go the section titled “For Wi-Fi Miracast or Intel
WiDi Device” on the other side of this Guide.
Install the Receiver
A
Step
1 Get the ScreenBeam Receiver, power cord, and HDMI
cable from the package.
Step
2 Plug one end of the power
cord into the power port on the
back of the Receiver.
Plug the other end into a nearby
electrical outlet.
Note: Use the 5V/2A power adapter provided by Actiontec (Model # WA-
10P05FU) only.
Step
3 Plug one end of the HDMI
cable into the HDMI port on the
back of the Receiver.
Plug the other end into an HDMI
port on your HDTV.
Install the Software and USB Transmitter
B
This section will guide you through the Wireless Display Software
and USB Transmitter setup. If your laptop/PC has either Intel WiDi
3.5 (or higher) or Wi-Fi Miracast (e.g., Windows 8.1 or Android
4.2), then proceed to the section of this Installation Guide titled
“For Wi-Fi Miracast or Intel WiDi Devices.”
Step
1 Insert the ScreenBeam CD
into the CD drive of a laptop/PC.
An AutoPlay window appears on
the screen.
Click Run setup.exe, then follow
the onscreen instructions.
Note: The AutoPlay window may look dierent, depending on the operating system version being used on the device..
Step
2 When you see the screen
shown on the right, make sure
you’ve completed the steps in
Section A of this Guide.
Then, continue to follow the
onscreen instructions.
Step
3 When you see the screen
shown on the right, get the
ScreenBeam Wireless Display
USB Transmitter.
Step
4 Insert the USB Transmitter
into a USB port on your laptop/PC,
then click Next.
Note: If the USB Transmitter was already connected to the laptop/PC prior
to step 4, unplug it, then plug it back in.
Step
5 Click in the button next to
“Yes, I want to restart my computer
now,” then click Finish.
The laptop/PC reboots.
Pair the Receiver and USB Transmitter
C
Step
1 Launch the ScreenBeam
Wireless Display application by
clicking on the ScreenBeam icon
on the Windows desktop, or locate
then launch the application from
Windows Search.
Note: You may encounter a product registration screen requesting for the
software registration key. The registration key can be found on the back of
the software CD sleeve.
Step
2 The main ScreenBeam
screen appears. Click Add a
Receiver.
Make sure your HDTV is set to the
same HDMI port to which you
connected the Receiver.
Note: If you don’t see the AutoPlay screen, locate the CD-ROM folder from
Windows Explorer, then double-click on setup.exe. If your laptop/PC does
not have a CD/DVD drive, go to www.actiontec.com/screenbeamkit
to download the ScreenBeam software.
Note: Actiontec recommends plugging in your laptop/PC when using
ScreenBeam. If running your laptop on battery, make sure its power
settings are congured for “Maximum Performance.”
Flip this Guide over to continue
NEXT
Loading...