Page 1
2013/12/09
Indoor PTZ
Mounting on the Ceiling
with Flat Surface
(Face Down)
Installation Guide
For Models:
I91, I92, KCM-8111
Page 2
www.acti.com
Installation Guide
Table of Contents
Installation Procedures ..................................................... 3
Step 1: Prepare for Installation ................................................................. 3
Step 2: Attach the Mounting Plate ............................................................ 3
Step 3: Attach the Fixing Bracket ............................................................. 4
Step 4: Install the Camera ......................................................................... 5
Step 5: Access the Camera Live View ...................................................... 7
Safety Information .............................................................. 8
2
Page 3
www.acti.com
Installation Guide
Installation Procedures
The camera package comes with a surface mount kit which allows the camera to be directly
installed onto a hard ceiling with flat surface.
Step 1: Prepare for Installation
1. Using the mount drill template, mark the screw holes on the ceiling, then drill the holes and
insert the supplied plastic plugs.
2. Push at the marked points below to detach the cover ring from the metal plate.
Step 2: Attach the Mounting Plate
Attach the mounting plate to the ceiling using the three (3) supplied screws.
3
Page 4
www.acti.com
Installation Guide
Step 3: Attach the Fixing Bracket
Align and attach the fixing bracket to one of the holes on the camera using the supplied screw
(holes marked below). The fixing bracket will fix the camera position when mounted later.
4
Page 5
www.acti.com
Installation Guide
Step 4: Install the Camera
1. If necessary, insert a memory card into the card slot of the camera.
2. Align and insert the camera base hooks to the mounting holes of the metal plate.
3. Slide the camera clockwise to secure the hooks to the mount.
4. Tighten the screw on the fixing bracket to fix the camera position. This is to avoid accidental
camera movement as the camera performs PTZ functions.
5
Page 6
www.acti.com
Installation Guide
5. Connect the network cable, power adaptor and any other cable connections (such as DI/DO,
audio in, etc.) to the camera.
NOTE:
The cables may be routed along the ceiling if the camera is installed on a hard ceiling.
Or, the cables may pass through a hole on the ceiling if the camera is installed on a
dropped ceiling.
For more information on connecting the terminal blocks for the power adaptor, Digital
Input / Output (DI/DO), or audio input, please refer to the camera model Hardware
Manual downloadable from the website (www.acti.com).
6. Remove the pre-cut tab on the cover ring using pliers.
7. Note that the cables will pass through the cut, align the metal plate hooks onto the holes of
the cover ring and then push to secure it in place.
Final installation would look similar to the picture below.
6
Page 7
www.acti.com
Installation Guide
Step 5: Access the Camera Live View
Refer to the camera Hardware Manual downloadable from the website (www.acti.com) for more
information.
7
Page 8
www.acti.com
Installation Guide
Safety Information
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Do not use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself. Refer all servicing to qualified service
personnel.
8
Page 9
www.acti.com
Installation Guide
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the inner parts of video product have been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
9
Loading...