ACTi Indoor Hemispheric Installation Guide
2014/01/10
Indoor Hemispheric
Mounting on the Wall
(Face Forward)
Installation Guide
For Models:
KCM-3911, B55, B56
www.acti.com
Installation Guide
Table of Contents
Introduction ........................................................................ 3
Installation Procedures of KCM-3911 ............................... 4
Step 1: Unpack the Camera ...................................................................... 4
Step 2: Prepare Other Device Connectors (Optional) ............................. 4
Step 3: Install the Base Plate .................................................................... 5
Step 4: Attach the Camera to the Base Plate .......................................... 6
Step 5: Connect the Cables ...................................................................... 7
Step 6: Connect to Network ...................................................................... 9
Step 7: Access the Camera Live View ...................................................... 9
Installation Procedures of B5x Fisheye Domes ............ 10
Step 1: Drill the Holes .............................................................................. 10
Step 2: Prepare the Camera ..................................................................... 11
Step 3: Prepare Other Device Connectors (Optional) ........................... 12
Step 4: Install the Camera ....................................................................... 12
Step 5: Connect the Cable(s) .................................................................. 13
Step 6: Complete the Installation ........................................................... 14
Step 7: Access the Camera Live View .................................................... 15
Appendices ....................................................................... 16
How to Connect a Power Adapter (Optional) ........................................ 16
How to Connect DI/DO Devices (Optional) ............................................ 18
KCM-3911 DI/DO Connector ................................................................. 18
B5x Fisheye Dome DI/DO Connector ................................................... 21
Safety Information ............................................................ 24
2
www.acti.com
Installation Guide
Camera Model
Description
Required Accessories
KCM-3911
The KCM-3911 comes with a bundled
mounting plate for installing the camera
on the surface. See Installation
Procedures of KCM-3911 on page 4.
Bundled Mounting Plate
B55, B56
This fisheye camera can be directly
installed on the surface without additional
mounting accessories. See Installation
Procedures of B5x Fisheye Domes on
page 10.
None
Introduction
This guide covers the step-by-step procedures in directly mounting the camera on a wall.
Bundled surface mounting accessories and connectors vary depending on model. Refer to the
installation procedures of your camera model as below:
3
www.acti.com
Installation Guide
Installation Procedures of KCM-3911
Step 1: Unpack the Camera
1. Slightly twist the cover ring counter-clockwise and pull to detach it.
2. Remove the sticker label.
3. Set the camera aside for later installation.
Step 2: Prepare Other Device Connectors (Optional)
The camera supports external power supply with a DC12V power adapter and digital input /
output devices useful for event triggers, and audio input / output devices. The use of these
devices is optional depending on the user application. If a power adapter or DI/DO device will be
used, connect these devices to the corresponding terminal blocks supplied with the camera at
this point. Otherwise, skip this step.
Refer to the following sections for detailed information:
How to Connect a Power Adapter (Optional) on page 16
How to Connect DI/DO Devices (Optional) on page 18
4
www.acti.com
Installation Guide
Screw hole
Camera Connectors Side
Base Plate
Connectors Side
Step 3: Install the Base Plate
IMPORTANT!
Before drilling the holes on the surface, note the camera placement and where you should drill
the hole where the cables will pass through or how the cable will go along the surface.
For wall installations, the connectors side must face up to install the camera with a correct
orientation.
1. After considering the orientation direction, drill the three (3) holes on the surface using the
drill template or the base plate itself as the template. If the cables will pass through the
surface, drill also the cable hole at this point.
5
www.acti.com
Installation Guide
2. Secure the base plate to the surface using the supplied screws.
Step 4: Attach the Camera to the Base Plate
1. Align the screw holes of the camera to the base plate.
2. Secure the camera to the base plate using the supplied screws.
6
www.acti.com
Installation Guide
Ethernet Cable
DC 12V
Power
Audio
Connector
Step 5: Connect the Cables
1. Connect the bundled network cable and if necessary, other connectors, like audio, DC 12V
power, and DI/DO. Sample image below.
2. Attach the cover ring, take note that the arrow on the camera should be aligned with the
arrow on the cover ring.
NOTE: The cables must be slightly bent underneath the cover ring.
3. Twist the ring counter-clockwise to secure the ring to the camera.
7
www.acti.com
Installation Guide
Network Side
Ethernet Port of
Camera Network Cable
Audio Input Jack
Audio Output Jack
Audio Device
4. Connect the Ethernet cable from the network side to the Ethernet port of the bundled network
cable.
5. If using an audio input device, such as a microphone with a built-in amplifier, connect the
device jack to the RED jack of the bundled audio cable. If using an audio output device, such
as a speaker, connect the device jack to the GREEN jack of the bundled audio cable.
Note: Make sure that the connected audio input device has a built-in amplifier. Connecting an
ordinary microphone will dwarf sounds and will result in inaudible recording.
8
Loading...