Page 1
694TA
User's Manual Version 1.0
The information presented in this publication has been
made carefully for reliability; however, no responsibility
is assumed for inaccuracies. Specifications are subject
to change without notice.
IBM, PC/AT, and PC/XT are trademarks of Interna-
tional Business Machines Corporation.
Socket370 is a trademark of Intel Corporation
AWARD is a registered trademark of Phoenix
Sofftware Inc.
MS-DOS and WINDOWS NT are registered trade-
marks of Microsoft Corporation.
Trademarks and/or registered trademarks are the
properties of their respective owners.
i
Page 2
Table of Contents
IntrnctctinnIntrnctctinn
Intrnctctinn
IntrnctctinnIntrnctctinn
1. Mnthdranarc Ddrcriotinn1. Mnthdranarc Ddrcriotinn
1. Mnthdranarc Ddrcriotinn
1. Mnthdranarc Ddrcriotinn1. Mnthdranarc Ddrcriotinn
1.1 Fdattrdr
1.1.1 Harcward 1-1
1.1.1 Snetward 1-4
1.1.3 Attachmdntr 1-4
1.1 Mnthdranarc Inrtallatinn
1.1.1 Mnthdranarc Mao 1-5
1.1.1 Mnthdranarc Layntt 1-6
1.3 Mnthdranarc Cnnndctnrr
1.3.1 Frnnt Pandl Cnnndctnrr(PANEL1( 1-8
1.3.1 Flnooy Dirk Cnnndctnr(FDC1( 1-9
1.3.3 Harc Dirk Cnnndctnrr(IDE1.IDE1( 1-9
1.3.4 ATW 10-oin Pnwdr Cnnndctnr(PW1( 1-10
1.3.5 Inerardc Cnnndctnr(IR1( 1-10
1.4 Back Pandl Cnnndctnrr
1.4.1 PS.1 Mntrd.Kdyanarc CNNN. 1-11
1.4.1 USB Cnnndctnrr (USB1.USB1( 1-11
1.5 Sdrial anc Paralldl Intdreacd onrtr 1-13
1.6 CPU Inrtallatinn
1.6.1 CPU Inrtallatinn Prnctct(Snckdt 360( 1-15
1.6.1 CPU Clnck Frdqtdncy Sdtting(SP-J4( 1-16
1.6 Jtmodr Sdtting
1.6.1 CPU Fan Cnnndctnr(FAN1.1( 1-16
1.6.1 Wakd-Nn-Mncdm Hdacdr(WNM1( 1-18
1.6.3 Wakd-Nn-LAN Hdacdr(WNL1( 1-18
1.6.4 AMR Sdt Ftnctinn(J1( 1-18
1.6.5 CMNS Ftnctinn Sdldctinn(CMNS1( 1-18
1.8 DRAM Inrtallatinn
1.8.1 DIMM 1-19
1.8.1 Hnw tn inrtall a DIMM Mnctld 1-19
ii
Page 3
Table of Contents
1.9 Atcin Staryrtdm
1.9.1 CD-Atcin-IN Cnnndctnrr(CDIN1.CDIN1( 1-10
1.10 Smart Pandl Nnanarc Cnnndctnr
1.10.1 Pnrt 80 Ddatg Ftnctinn(SP-J6( 1-11
1.10.1 Sdcnnc BINS Cnnndctnr(SP-J1( 1-11
1.10.3 Strodnc Mncd.Vnicd Ddatg(SP-J3( 1-11
1.10.4 AUW LINE(SP-J5( 1-13
1.10.5 FSB Acjtrt(SP-J4( 1-13
1.10.6 Frnnt CNM1 Hdacdr Cnnndctnr (SP-J6( 1-13
1. BINS Sdtto1. BINS Sdtto
1. BINS Sdtto
1. BINS Sdtto1. BINS Sdtto
1.1 Main Mdnt 1-4
1.1 Stancarc CMNS Fdattrdr 1- 6
1.3 Acuancdc BINS Fdattrdr 1-10
1.4 Acuancdc Chiordt Fdattrdr 1-14
1.5 Intdgratdc Pdriohdralr 1-19
1.6 Pnwdr Managdmdnt Sdtto 1- 14
1.6 PnP.PCI Cnneigtratinnr 1-30
1.8 PC Hdalth Stattr 1-34
1.9 Frdqtdncy.Vnltagd Cnntrnl 1-35
1.10 Lnac Fail-Saed Ddeatltr 1-36
1.11 Lnac Notimizdc Ddeatltr 1-36
1.11 Sdt Stodruirnr.trdr Parrwnrc 1-38
1.13 Saud & Exit Sdtto 1-40
1.14 Exit Withntt Sauing 1-41
(notinn((notinn(
(notinn(
(notinn((notinn(
3. Driudr Inrtallatinn3. Driudr Inrtallatinn
3. Driudr Inrtallatinn
3. Driudr Inrtallatinn3. Driudr Inrtallatinn
3.1 Main Mdnt 3-1
3.1 Inrtalling VIA 4 in 1 Driudr 3-1
3.3 Inrtalling Atcin Driudr 3-3
iii
Page 4
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Introduction
System Overview
This manual was written to help you start using this product
as quickly and smoothly as possbile. Inside, you will find
the answers to solve most problems. In order for this
reference material to be of greatest use, refer to the
“expanded table of contents” to find relevant topics.
This board provides a total PC solution by incorporating the
System , I/O , and PCI IDE. The mainboard support single
Intel PIII Celeron/Coppermine processors base PC ATX
system, AMR Bus,PCI Local Bus, and AGP Bus to upgrades
your system performance.
It is ideal for multi-tasking and fully supports MS-DOS,
Windows, Windows NT , Windows ME, Windows 2000,
Novell, OS/2, Windows95/98, Windows 98SE , UNIX ,
SCO UNIX etc.
This manual also explains how to install the mainboard for
operation, and how to setup your CMOS configuration with
the BIOS setup program.
1-11-1
1-1
1-11-1
Page 5
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.Motherboard Description
1.1 Features
1.1.1 Hardware
CPU
-Socket 370 for Intel PIII/Tualatin/PIII D Step Processor.
-Intel FC-PGA Celeron Processors 500MHz~800MHz or
higher processor with 66/100MHz FSB.
-Intel FC-PGA Pentium III Processors 500MHz~1.2GHz
or higher processor with 100/133MHz FSB.
-VIA Cyrix III Processor with 100/133MHz FSB.
Speed
-Supports 33MHz PCI Bus speed.
-Supports 4X AGP Bus.
DRAM Memory
-Supports 8/16/32/64....MB DIMM module socket.
-Supports Synchronous DRAM(3.3V)
-Supports a maximum memory size of 1.536GB with SDRAM.
Shadow RAM
-A memory controller provide shadow RAM and supports
8-bit ROM BIOS.
Green Function
-Support power management operation VIA BIOS.
-Power down timer from 1 to 15 mins.
-Wakes from power saving sleep mode at the press of
any key or any mouse activity.
Bus Slots
-Provide one AMR slot and AGP slot.
-Five 32-bit PCI bus.
1-11-1
1-1
1-11-1
Page 6
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Universal Serial Bus
-Supports two back Universal Serial Bus(USB)Ports
and two front Universal serial Bus(USB)Ports.
Hardware Monitor Function
-CPU Fan Speed Monitor.
-CPU Temperature Monitor.
-System Voltage Monitor.
Power Management
Support multiple system suspend types-suspend to DRAM, suspend to
disk, and all with hardware automatic wake-up.
IDE Bulit-in On Board
-Supports four IDE devices.
-Supports PIO Mode 4, Master Mode, high performance hard disk
drives.
-Support Ultra DMA 33/66/100 Bus Master Mode.
-Supports IDE interface with CD-ROM.
-Supports high capacity hard disk drives.
-Support LBA mode.
PCI-Based AC 97 Digital Audio Processor
-AC 97 2.1 interface.
-16 channels of high-quality sample rate conversion.
-16x8 channel digital mixer.
-Stereo 10 band graphic equalizer.
-Sound Blaster and Sound Blaster Pro emulation.
WOL/WOM (Wake On LAN & Wake On Modem)
Supports system power up from LAN/Modem ring up .
Smart Panel
Supports BIOS Port 80H POST Code output to debug LED.
1-31-3
1-3
1-31-3
Page 7
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
I/O Bulit-in On Board
-Supports one multi-mode Parallel Port.
(1)Standard & Bidirection Parallel Port
(2)Enhanced Parallel Port (EPP)
(3)Extended Capabilities Port
-Supports two serial ports, 16550 UART.
-Supports one Infrared transmission (IR).
-Supports PS/2 mouse and PS/2 Keyboard.
-Supports 360KB, 720KB, 1.2MB, 1.44MB, and 2.88MB floppy disk
drivers.
1.1.2 Software
BIOS
-AWARD legal BIOS.
-Supports APM 1.2.
-Supports USB Function.
-Supports ACPI
Operation System
-Supporting the highest performance for MS-DOS,Windows,
Windows NT, Windows 2000, Windows ME, Novell, OS/2,
Windows 95/98, Windows 98 SE, UNIX, SCO UNIX etc.
1.1.3 Attachments
-HDD UDMA66/100 Cable.
-FDD Cable.
-Flash Memory Written for BIOS Update.
-USB2 Cable (Option).
-Fully Setup CD Driver built in Utility(Ghost, Anitivirus,
Adobe Acrobat).
-This Manual.
1-41-4
1-4
1-41-4
Page 8
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.2 Motherboard Installation
1.2.1 Motherboard Map
1-51-5
1-5
1-51-5
Page 9
CC
hh
aa
oo
ss
dd
rr
11
C
h
a
o
s
d
r
1
CC
hh
aa
oo
ss
dd
rr
11
1.2.2 Motherboard Layout
MM
nn
ss
hh
dd
rr
aa
nn
aa
rr
cc
CC
dd
rr
bb
rr
hh
oo
ss
hh
nn
M
n
s
h
d
r
a
n
a
r
c
C
d
r
MM
nn
ss
hh
dd
rr
aa
nn
aa
FAN1
b
rr
cc
CC
dd
rr
bb
nn
r
h
o
s
h
n
n
rr
hh
oo
ss
hh
nn
nn
USB1
COM1
COM2
Speak out
Line in
MIC in
SP-J6
Printer
GAME1
SP-J7
370
VIA
AGP SLOT
PCI1
PCI2
1
PCI3
PCI4
SP-J2
DIMM1
VIA
SP-J4
DIMM2
DIMM3
CMOS1
PAN E L 1
SP-J3
J1
AMR SLOT
1-61-6
1-6
1-61-6
PCI5
FAN2
Page 10
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.3 Motherboard Connectors
15
USB1
6
FAN1
SP-J4
11
13
COM1
1
COM2
Speak out
Line in
MIC in
Printer
GAME1
2
15
SP-J6
SP-J7
10
3,4
12
1.Babk Oandk I.O Cnnndbsnrr1.Babk Oandk I.O Cnnndbsnrr
1.Babk Oandk I.O Cnnndbsnrr
1.Babk Oandk I.O Cnnndbsnrr1.Babk Oandk I.O Cnnndbsnrr
3.Wakd-On MOCDM Cnnndbsnr3.Wakd-On MOCDM Cnnndbsnr
3.Wakd-On MOCDM Cnnndbsnr
3.Wakd-On MOCDM Cnnndbsnr3.Wakd-On MOCDM Cnnndbsnr
5.Frnns Oandk Cnnndbsnr5.Frnns Oandk Cnnndbsnr
5.Frnns Oandk Cnnndbsnr
5.Frnns Oandk Cnnndbsnr5.Frnns Oandk Cnnndbsnr
7.Fknooy Cnnndbsnr7.Fknooy Cnnndbsnr
7.Fknooy Cnnndbsnr
7.Fknooy Cnnndbsnr7.Fknooy Cnnndbsnr
9.IR Cnnndbsnr9.IR Cnnndbsnr
9.IR Cnnndbsnr
9.IR Cnnndbsnr9.IR Cnnndbsnr
11.ATX Onwdr Cnnndbsnr11.ATX Onwdr Cnnndbsnr
11.ATX Onwdr Cnnndbsnr
11.ATX Onwdr Cnnndbsnr11.ATX Onwdr Cnnndbsnr
13.COU Cknbk Frdq. Sdkdbshnn(SO-J4(13.COU Cknbk Frdq. Sdkdbshnn(SO-J4(
13.COU Cknbk Frdq. Sdkdbshnn(SO-J4(
13.COU Cknbk Frdq. Sdkdbshnn(SO-J4(13.COU Cknbk Frdq. Sdkdbshnn(SO-J4(
14.CMOS Ftnbshn n Sdk dbshnn(CMOS1(14.CMO S Ftnbsh nn Sdkdbshn n(CMO S1(
14.CMOS Ftnbshn n Sdk dbshnn(CMOS1(
14.CMOS Ftnbshn n Sdk dbshnn(CMOS1(14.CMO S Ftnbsh nn Sdkdbshn n(CMO S1(
15.Slars Oand k Ftnbsh nn(SO-J1.SO-J3. SO-J6.SO-J5.SO-J4. SO-J7(15.Slars Oandk Ftn bshn n (SO-J1.SO-J3.SO-J6. SO-J5. SO-J4.SO-J7(
15.Slars Oand k Ftnbsh nn(SO-J1.SO-J3. SO-J6.SO-J5.SO-J4. SO-J7(
15.Slars Oand k Ftnbsh nn(SO-J1.SO-J3. SO-J6.SO-J5.SO-J4. SO-J7(15.Slars Oandk Ftn bshn n (SO-J1.SO-J3.SO-J6. SO-J5. SO-J4.SO-J7(
(noshn n((noshn n(
(noshn n(
(noshn n((noshn n(
J1
AMR SLOT
370
VIA
AGP SLOT
PCI1
PCI2
1
PCI3
PCI4
SP-J2
PCI5
15
1.CC Atchn-In Cnnndbsnr1.CC Atchn-In Cnnndbsnr
1.CC Atchn-In Cnnndbsnr
1.CC Atchn-In Cnnndbsnr1.CC Atchn-In Cnnndbsnr
4.Wakd-On-LAN Cnnndbsnr4.Wakd-On-LAN Cnnndbsnr
4.Wakd-On-LAN Cnnndbsnr
4.Wakd-On-LAN Cnnndbsnr4.Wakd-On-LAN Cnnndbsnr
6.Fan Cnnndbsnrr(Fan1 .1(6.Fan Cnnndbsnrr(Fan1 .1(
6.Fan Cnnndbsnrr(Fan1 .1(
6.Fan Cnnndbsnrr(Fan1 .1(6.Fan Cnnndbsnrr(Fan1 .1(
8.ICD Cnnndbsnrr8.ICD Cnnndbsnrr
8.ICD Cnnndbsnrr
8.ICD Cnnndbsnrr8.ICD Cnnndbsnrr
10.Frnns USB1 Cnnndbsnr10.Frnns USB1 Cnnndbsnr
10.Frnns USB1 Cnnndbsnr
10.Frnns USB1 Cnnndbsnr10.Frnns USB1 Cnnndbsnr
11.AMR Sds Ftnbshnn (J1(11.AMR Sds Ftn bshn n(J1(
11.AMR Sds Ftnbshnn (J1(
11.AMR Sds Ftnbshnn (J1(11.AMR Sds Ftn bshn n(J1(
1-71-7
1-7
1-71-7
DIMM2
DIMM1
DIMM3
VIA
FAN2
7
6
8
14
CMOS1
9
PAN E L 1
SP-J3
5
15
Page 11
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.3.1 Front Panel Connector (PANEL1)
PANEL Connector
PW_BN
S5LED
+
PW_LED
SPEAKER
+
1
2
+
SMI_LED
RESET
+
HD_LED
+
EXTSMI
Speaker Connector (SPEAKER)
An offboard speaker can be installed onto the motherboard as a
manufacturing option. An offboard speaker can be connected to
the motherboard at the front pannel connector. The speaker
(onboard or offboard) provides error beep code information during the Power Self-Test when the computer cannot use the video
interface. The speaker is not connected to the audio subsystem
and does not receive output from the audio subsystem.
Hard Drive LED Connector (HD_LED)
This connector supplies power to the cabinet IDE activity LED.
Read and write activity by devices connected to the Primary or
Secondary IDE connectors will cause the LED to light up.
SMI Suspend Switch Lead (EXTSMI)
This allows the user to manually place the system into a suspend
mode of Green mode. System activity will be instantly decreased
to save electricity and expand the life of certain components
when the system is not in use. This 2-pin connector (see the
figure) connects to the case-mounted suspend switch. If you do
not have a switch for the connector, you may use the "Turbo
Switch” instead since it does not have a function. SMI is
activated when it detects a short. It may require one or two
pushes depending on the position of the switch. Wake-up can be
controlled by settings in the BIOS but the keyboard will always
allow wake-up (the SMI Suspend Switch Lead cannot wake-up
the system). If you want to use this connector, the "Suspend
Switch" in the Power Management Setup of the BIOS SOFTWARE section should be on the default setting of Enable.
1-81-8
1-8
1-81-8
Page 12
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
ATX Power Switch (PW_BN)
The system power is controlled by a momentary switch
connected to this lead. Pushing the button once will switch
the system ON. The system power LED lights when the
system's power is on .
Power LED Lead (PW_LED)
The system power LED lights when the system power is on.
SMI LED Lead (SMI_LED)
The system SMI LED lights when the system suspend is on.
Reset Switch Lead (RESET)
The connector can be connected to a momentary SPST type
switch that is normally open. When the switch is closed, the
motherboard resets and runs the POST.
S5_LED Lead (S5LED)
The system S5_LED lights when the system suspend is on
the S5 mode.
1.3.2 Floppy Disk Connector (FDC1)
This connector supports the provided floppy drive ribbon
cable. After connecting the single end to the board, connect
the two plugs on the other end to the floppy drives.
1.3.3 Hard Disk Connectors (IDE1/IDE2)
These connectors support the provided IDE hard disk ribbon
cable. After connecting the single end to the board, connect
the two plugs at the other end to your hard disk.
If you install two hard disks, you must configure the second
drive to Slave mode by setting its jumper settings. BIOS now
supports SCSI device or IDE CD-ROM boot up (see "HDD
Sequence SCSI/IDE First" & "Boot Sequence" in the BIOS
Features Setup of the BIOS SOFTWARE) (Pin 20 is removed
to prevent inserting in the wrong orientation when using
ribbon cables with pin 20 plugged) .
1-91-9
1-9
1-91-9
Page 13
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.3.4 ATX 20-pin Power Connector (PW1)
This connector supports the power button on-board. Using
the ATX power supply, functions such as Modem Ring Wake-
Up and Soft Power Off are supported on this motherboard .
This power connector supports instant power-on
functionality, which means that the system will boot up
instantly when the power connector is inserted on the board.
Pin Signal Pin Signal
1 3.3V 11 3.3V
2 3.3V 12 -12V
3 GND 13 GND
4 5V 14 PS-ON
5 GND 15 GND
6 5V 16 GND
7 GND 17 GND
8 PW-OK 18 -5V
9 5V_SB 19 5V
10 12V 20 5V
1.3.5 Infrared Connector (IR1)
After the IrDA interface is configured, files can be
transferred from or to portable devices such as laptops,
PDAs, and printers using application software.
1-101-10
1-10
1-101-10
Page 14
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Serial Port(9-pin Male)
LINE IN
Parallel (Printer) Port
MIDI/(GAME) Port
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.4 Back Panel Connectors
PS/2 Mouse
(25-pin Fem ale)
USB1
(15-pin Fem ale)
PS/2 Keyboard
(6-pin Fem ale)
COM1
COM2
SPEAKER
1.4.1 PS/2 Mouse /Keyboard CONN.
The motherboard provides a standard PS/2 mouse / Keyboard
mini DIN connector for attaching a PS/2 mouse. You can
plug a PS/2 mouse / Keyboard directly into this connector.
1.4.2 USB Connectors: USB1 & USB2
The motherboard provides a OHCI(Open Host Controller
Interface)Universal Serial Bus Roots for attaching USB
devices such as a keyboard, mouse and other USB devices.
You can plug the USB devices directly into this connector.
Pin Signal
1 +5V_SB
2 USBP0-(USBP1-)
USB1
3 USBP0+(USBP1+)
4 GND
MIC
1-111-11
1-11
1-111-11
Page 15
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Front Two USB Connectors: USB2
FAN1
USB2
VCC
P2-
P2+
GND
GND
Speak out
Line in
1
3
5
7
9
USB1
COM1
COM2
MIC in
SP-J4
370
Printer
GAME1
VIA
DIMM2
DIMM1
DIMM3
AGP SLOT
PCI1
SP-J7
SP-J6
1
PCI2
VIA
PCI3
PCI4
SP-J2
J1
AMR SLOT
2
GND
4
GND
6
P3+
8
P3-
10
VCC
PCI5
CMOS1
PAN E L 1
SP-J3
FAN2
1-111-11
1-11
1-111-11
Page 16
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.5 Serial and Parallel Interface Ports
This system comes equipped with two serial ports and one
parpllel port. Both types of interface ports will be explained
in this chapter.
The Serial Interfaces: COM1/COM2
The serial interface port is sometimes refered to as an RS-
232 port or an asynchronous communication port. Mice,
printers, modems and other peripheral devices can be
connected to a serial port. The serial port can also be used
to connect your computer system. If you wish to transfer
the contents of your hard disk to another system it can be
accomplished by using each machine’s serial port.
COM1/COM2
The serial port on this system has one 9-pin connector.
Some older computer systems and peripherals used to be
equipped with only a 25-pin connector. Should you need to
connect your 9-pin serial port to an older 25-pin serial port,
you can purchase a 9-to-25 pin adapter.
1-131-13
1-13
1-131-13
Page 17
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Serial Port(9-pin Male)
LINE IN
Parallel (Printer) Port
MIDI/(GAME) Port
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Signal DB9 Pin DB25 Pin
DCD 1 8
RX 2 3
TX 3 2
DTR 4 2 0
GND 5 7
DSR 6 6
RTS 7 4
CTS 8 5
RI 9 2 2
Parallel Interface Port
Unlike serial ports, parallel interface ports have been
standardized and should not present any difficulty interfacing
peripherals to your system. Sometimes called a Centronics port,
the parallel port is almost exclusively used with printers. The
parallel port on your system has a 25-pin, DB 25 connector(see
the picture below).
PS/2 Mouse
(25-pin Fem ale)
USB1
(15-pin Fem ale)
PS/2 Keyboard
(6-pin Fem ale)
COM1
1-141-14
1-14
1-141-14
COM2
SPEAKER
MIC
Page 18
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.6 CPU Installation
1.6.1 CPU Installation Procedure: Socket 370
1. Pull the lever sideways away from the socket then raise
the lever to a 90-degree angle.
2. Locate Pin 1 in the socket and look for the white dot or
cut edge in the CPU. Match Pin 1 with the white dot/cut
edge then insert the CPU.
3. Press the lever down to complete the installation.
4. Make sure the spec of the heatsink is good enough.
FAN1
USB1
COM1
COM2
Speak out
Line in
MIC in
SP-J6
Printer
GAME1
SP-J7
J1
AMR SLOT
370
VIA
AGP SLOT
PCI1
PCI2
1
PCI3
PCI4
SP-J2
PCI5
DIMM1
1-151-15
1-15
1-151-15
VIA
DIMM2
DIMM3
SP-J4
CMOS1
Notch
PAN E L 1
SP-J3
FAN2
Page 19
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.6.2 CPU Clock Frequency Setting: SP-J4
Overclocking is operating a CPU/Processor beyond its
specified frequency. SP-J4 jumper is used for the CPU Front
Side Bus Frequencies from 100MHz to 133MHz.
FAN1
USB1
COM1
SP-J6
Printer
GAME1
SP-J7
COM2
Speak out
Line in
MIC in
CPU PCICLK 1-2 3-4
Auto 33.3 OFF OFF
(Default)
J1
133 33.3 OFF OFF
AMR SLOT
100 33.3 OFF ON
66 33.3 ON ON
370
VIA
AGP SLOT
PCI1
PCI2
1
PCI3
PCI4
SP-J2
PCI5
SP-J4
DIMM2
DIMM1
DIMM3
CMOS1
VIA
PAN E L 1
SP-J3
FAN2
O FFO FF
O FF
O FFO FF
O NO N
O N
O NO N
1-161-16
1-16
1-161-16
Page 20
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.7 Jumper Setting
A jumper has two or more pins that can be covered by a
plastic jumper cap, allowing you to select different system
options.
USB1
FAN1
Connector
FAN1
SP-J4
SP-J4
COM1
COM2
Speak out
Line in
MIC in
Printer
GAME1
370
VIA
AGP SLOT
PCI1
SP-J7
WOL1
WOM1
J1
SP-J6
J1
AMR SLOT
SP-J2
1
PCI2
PCI3
PCI4
PCI5
1.7.1 CPU/System Fan Connectors: Fan1/2
Pin Assignment
1 Ground
1
2
2 +12VDC
3
3 Signal
DIMM2
DIMM1
DIMM3
CMOS1
CMOS1
VIA
PAN E L 1
SP-J3
FAN2
FAN 2
Connector
1-171-17
1-17
1-171-17
Page 21
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.7.2 Wake-On Modem Header: WOM1
Pin Assignment
1 5V_SB
1
2 Ground
3
3 Signal
1.7.3 Wake-On LAN Header: WOL1
Pin Assignment
1 5V_SB
1
2 Ground
3
3 Signal
1.7.4 AMR Set Function: J1
Pin Assignment
ON Enabled AMR Slot
(Defacult)
OFF Disabled AMR Slot
1.7.5 CMOS Function Selection:CMOS1
Pin Assignment
1-2 Normal (Default)
2-3 Clear CMOS
NOTE:
(Please follow the procedure below to clear CMOS data.)
(1)Remove the AC power line.(2)CMOS1(2-3)Closed.(3)Wait
five seconds.(4)CMOS1(1-2) Closed.(5)AC Power on.(6)Re-
set your desired password or clear CMOS data.
1-181-18
1-18
1-181-18
Page 22
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.8 DRAM Installation
1.8.1 DIMM
DRAM Access Time: 3.3V Unbuffered SDRAM/ PC66/
PC100 and PC133 Type required.
DRAM Type: 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,
512MB DIMM Module. (168 pin)
Bank Memory module
DIMM 1 16MB,32MB, 64MB, 128MB, 256MB, 512MB
( Bank 0-1 ) 168 pin, 3.3v SDRAM
DIMM 2 16MB,32MB, 64MB, 128MB, 256MB, 512MB
( Bank 2-3 ) 168 pin, 3.3vSDRAM
DIMM 3 16MB,32MB, 64MB, 128MB, 256MB, 512MB
( Bank 4-5 ) 168 pin, 3.3v SDRAM
Total System Memory (Max 1.536GB)
1.8.2 How to install a DIMM Module
1. The DIMM socket has a “Plastic Safety Tab” and the DIMM
memory module has an asymmetrical notch”, so the DIMM
memory module can only fit into the slot in one direction.
2. Push the tabs out. Insert the DIMM memory modules
into the socket at a 90-degree angle then push down
vertically so that it will fit into place.
3. The Mounting Holes and plastic tabs should fit over the
edge and hold the DIMM memory modules in place.
168Ohn CIMM Snbkds168Ohn CIMM Snbkds
168Ohn CIMM Snbkds168Ohn CIMM Snbkds
168Ohn CIMM Snbkds
88 pins 60 pins 20 pins
1-191-19
1-19
1-191-19
Page 23
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.9 Audio Subsystem
FAN1
USB1
370
VIA
AGP SLOT
DIMM1
DIMM2
CDIN1
CDIN2
COM1
COM2
Speak out
Line in
MIC in
Printer
GAME1
PCI1
SP-J7
SP-J6
PCI2
1
VIA
PCI3
PCI4
SP-J2
J1
AMR SLOT
PCI5
1.9.1 CD Audio-in Connectors: CDIN1/CDIN2
Pin CDIN1 Assignment
1 CD-L
2 GND
3 GND
4 CD-R
SP-J4
DIMM3
CMOS1
PAN E L 1
SP-J3
FAN2
Pin CDIN2 Assignment
1 GND
2 CD-L
3 GND
4 CD-R
1-101-10
1-10
1-101-10
Page 24
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.10 Smart Panel Onboard Connector
SP-J5
FAN1
SP-J4
USB1
SP-J4
COM1
COM2
Speak out
Line in
MIC in
Printer
GAME1
370
VIA
DIMM2
DIMM1
DIMM3
AGP SLOT
1
PCI1
PCI2
VIA
SP-J6
SP-J7
SP-J6
SP-J7
PCI3
PCI4
SP-J2
J1
AMR SLOT
PCI5
FAN2
SP-J2 SP-J3
Note:
The motherboard provides the pin leads for Smart Panel. If
you want POST Error Code or Smart Panel function, please
refer to Smart Panel (SP694TA ) manual.
CMOS1
PAN E L 1
SP-J3
1-111-11
1-11
1-111-11
Page 25
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.10.1 Port 80 Debug Function: SP-J6
For Smart Panel connector(SP-J6) to M/B (SP-
J6)
Pin SP-J6 Assignment Pin SP-J6 Assignment
1 ERD0 2 ERD4
3 ERD1 4 ERD5
5 ERD2 6 ERD6
7 ERD3 8 ERD7
9 GND 10 GND
1.10.2 Second BIOS Connector: SP-J2
For Smart Panel connector(SP-J2) to M/B (SP-
J2)
Pin SP-J2 Assignment Pin SP-J2 Assignment
1 SD0 2 +5V
3 SD1 4 SA0
5 SD2 6 SA1
7 SD3 8 SA2
9 SD4 10 SA3
11 SD5 12 SA4
13 SD6 14 SA5
15 SD7 16 SA6
17 GND 18 DISABLE
19 ROMCS- 20 SA7
21 MEMR- 22 SA8
23 MEMW- 24 SA9
25 SA18 26 SA10
27 SA17 28 SA11
29 SA16 30 SA12
31 SA15 32 SA13
33 +5V 34 SA14
1.10.3 Suspend Mode / Voice Debug: SP-J3
For Smart Panel connector(SP-J3) to M/B (SP-
J3)
Pin SP-J3 Assignment Pin SP-J3 Assignment
1 VCC 2 GND
3 GPO4 4 S3LED+
5 GPO5 6 GND
7 GPO8 8 S5LED+
9 SPK 10 GPOD
11 GND 12 PCIRST
1-111-11
1-11
1-111-11
Page 26
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nn
Chaosdr 1 Mnshdranarc C drbrh osh nnChaosdr 1 Mnshdranarc C drbrh osh nn
1.10.4 AUX Line: SP-J5
For Smart Panel connector(SP-J5) to M/B (SP-
J5)
Pin SP-J5 Assignment Pin SP-J5 Assignment
1 LINE_OUT_L 2 LINE_OUT_R
3 LINE_IN_L 4 LINE_IN_R
5 MIC_IN_L 6 MIC_IN_R
1.10.5 FSB Adjust: SP-J4
For Smart Panel connector(SP-J4) to M/B (SP-
J4)
CPU PCICLK 1-2 3-4
Auto 33.3 OFF OFF
(Default)
133 33.3 OFF OFF
100 33.3 OFF ON
66 33.3 ON ON
O FFO FF
O FF
O FFO FF
O NO N
O N
O NO N
1.10.6 Front COM2 Header Conn.: SP-J7
For Smart Panel connector(SP-J7) to M/B (SP-
J7)
Pin SP-J7 Assignment Pin SP-J7 Assignment
1 DCD 2 RX
3 TX 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9RI
1-131-13
1-13
1-131-13
Page 27
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2. BIOS Setup
Introduction
This manual discussed the Award Setup program built into
the ROM BIOS. The Setup program allows the user to modify
the basic system configuration. This special information is
then stored in battery-backed RAM so that it retains the setup
information when the power is turned off.
The Award BIOS installed in your computer system’s ROM
(Read Only Memory)is a custom version of an industry
standard BIOS. This means that it supports Intel Celeron/
Coppermine PIII and VIA Cyrix, Tualatin processors input/
output system. The BIOS provides critical low-level support
for standard devices such as disk drives and serial and parallel
ports. The rest of this manual is intended to guide you through
the process of configuring your system using Setup.
Plug and Play Support
This AWARD BIOS supports the Plug and Play Version
1.0A specification. ESCD(Extended System Configuration
Data)write is supported.
EPA Green PC Support
This AWARD BIOS supports Version 1.03 of the EPA Green
PC specification.
PCI Bus Support
This AWARD BIOS also supports Version 2.1 of the Intel
PCI (Peripheral Component Interconnect)local bus
specification.
1-11-1
1-1
1-11-1
Page 28
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
APM Support
This AWARD BIOS supports Version 1.1&1.2 of the
Advanced Power Management(APM) specification.Power
management features are implemented via the System
Management Interrupt(SMI). Sleep and Suspend power
management modes are supported. Power to the hard disk
drives and video monitors can be managed by this AWARD
BIOS.
Support CPU
This AWARD BIOS supports the Intel Celeron/Coppermine
PIII and VIA Cyrix, Tualatin processor CPU.
Using Setup
In general, you use the arrow keys to highlight items, press
<Enter>to select, use the <PgUp>and <PgDn>keys to
change entries, press<F1>for help and press <Esc>to quit.
The following table provides more detail about how to
navigate in the Setup program by using the keyboard.
Note:
(BIOS version 1.0 is for reference only. If there is a
change in BIOS version, please use the actual version
on the BIOS.)
1-11-1
1-1
1-11-1
Page 29
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Keystroke Function
Up arrow Move to previous item
Down arrow Move to next item
Left arrow Move to the item on the left(menu bar)
Right arrow Move to the item on the right(menu bar)
Esc Main Menu: Quit without saving changes
Submenus: Exit Current page to the next higher
level menu
Move Enter Move to item you desired
PgUp key Increase the numeric value or make changes
PgDn key Decrease the numeric value or make changes
+Key Increase the numeric value or make changes
-Key Decrease the numeric value or make changes
Esc Key Main menu-Quit and not save changes into
CMOS
Status Page Setup Menu and option Page Setup
Menu-Exit Current page and return to Main
Menu
F1 Key General help on Setup navigation keys.
F5 Key Load previous values from CMOS
F6 Key Load the fail-safe defaults from BIOS default
table
F7 Key Load the optimized defaults
F10 Key Save all the CMOS changes and exit
1-21-2
1-2
1-21-2
Page 30
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.1 Main Menu
Once you enter AWARD BIOS CMOS Setup Utility, the Main
Menu will appear on the screen. The Main Menu allows you
to select from several setup function. Use the arrow keys to
select among the items and press<Enter> to accept and
enter the sub-menu.
“WARNING”
The information about BIOS defaults on manual (Figure
1,2,3,4,5,6,7,8,9,10,11,12,13,14)is just for reference, please
refer to the BIOS installed on the board for updated
information.
◎◎
◎ Figure 1. Main Menu
◎◎
CMOS Setup Utility-Copyright(C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configurations Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
Time , Date , Hard Disk Type ...
Standard CMOS Features
This setup page includes all the items in standard compatible
BIOS.
1-41-4
1-4
1-41-4
Page 31
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Advanced BIOS Features
This setup page includes all the items of the BIOS special
enchanced features.
Advanced Chipset Features
This setup page includes all the items of the Chipset special
enchanced features.
Integrated Peripherals
This selection page includes all the items of the IDE hard
drive and Programmed Input/Output features.
Power Management Setup
This setup page includes all the items of the power manage
ment features.
PnP/PCI Configurations
This setup page includes the user defined or default IRQ
Setting.
PC Health Status
This page shows the hardware Monitor information of the
system.
Frequency / Voltage Control
This setup page controls the CPU's clock and frequency ratio.
Load Fail-Safe Defaults
Use this menu to load the BIOS default values for the
minimal/stable performance for your system to operate.
1-51-5
1-5
1-51-5
Page 32
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Load Optimized Defaults
These settings are more likely to configure a workable
computer when something is wrong. If you cannot boot the
computer successfully, select the BIOS Setup options and
try to diagnose the problem after the computer boots. These
settings do not provide optional performance.
Set Supervisor Password
Change, set, or, disable password.It allows you to limit
accessto the system and Setup, or just to Setup.
Set User Password
You can specify both a User and a Supervisor password. When
you select either password option, you are prompted for a
1-6 character password. Enter the password and then retype
the password when prompted.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
1-61-6
1-6
1-61-6
Page 33
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.2 Standard CMOS Features
This item in the Standard CMOS Setup Menu is divided into
10 categories. Each category includes no, one or more than
one setup items. Use the arrow keys to highlight the item
and then use the <PgUp> or <PgDn> keys to select the value
you want in each item.
◎◎
◎ Figure 2. Standard CMOS Features
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features
Date(mm:dd:yy) Tue,Jun 6 2000 Item Help
Time (hh:mm:ss) 11:26:10
IDE Primary Master Press Enter None
IDE Primary Slave Press Enter None Change the day,
IDE Secondary Master Press Enter None month,year
IDE Secondary Master Press Enter None and century.
Drive A 1.44M,3.5 in
Drive B None
Video EGA/VGA
Halt On All,But Keyboard
Base Memory xxxx
Extended Memory xxxx
Total xxxx
Menu Level
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-71-7
1-7
1-71-7
Page 34
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Main Menu Selections
This table shows the selections that you can make on the
Main Menu.
Item Options Description
Date Month DD YYYY Set the system,date. Note that the
‘Day’ automatically changes
when you set the data.
IDE Primary Options are in its sub Press<Enter> to enter the sub menu
Master menu. of detailed.
IDE Primary Options are in its sub Press<Enter> to enter the sub menu
Slave menu. of detailed.
IDE Secondary Options are in its sub Press<Enter> to enter the sub menu
Master menu. of detailed.
IDE Secondary Options are in its sub Press<Enter> to enter the sub menu
Slave menu. of detailed.
Drive A None Select the type of floppy disk drive
Drive B 360K, 5.25in installed in your system.
1.2M, 5.25in
720K, 3.5in
1.44M, 3.5in
2.88M, 3.5in
Video EGA/VGA Select the default video device.
CGA 40
CGA 80
MONO
1-81-8
1-8
1-81-8
Page 35
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Item Options Description
Halt On All Errors Select the situation in which you
No Errors want the BIOS to stop the POST
All, but Keyboard process and notify.
All, but Diskette
All, but Disk/Key
Base Memory N/A Displays the amount of conventional
memory detected during boot up.
Extended N/A Displays the amount of conventional
Memory memory detected during boot up.
Total N/A Displays the total memory
Memory available in the system.
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
IDE Primary Master
IDE HDD Auto-Detection Press Enter Item Help
IDE Primary Master Auto
Access Mode Auto Menu Level
Capacity 13022MB
Cylinder 25232
Head 16
Precomp 0
Landing Zone 25231
Sector 61
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-91-9
1-9
1-91-9
Page 36
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.3 Advanced BIOS Features
◎◎
◎ Figure 3. Advanced BIOS Features
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Advanced BIOS Features
Virus Warning Enabled Item Help
CPU Internal Cache Enabled
External Cache Enabled Menu Level
CPU L2 Cache ECC Checking Enabled
Processor Number Feature Enabled Allows you to
Quick Power On Self Test Disabled choose the
First Boot Device Floopy VIRUS warning
Second Boot Device HDD-0 feature for IDE
Third Boot Device LS120 Hard Disk boot
Boot Other Device Enabled sector protection.
Swap Floppy Drive Disabled If this function
Boot Up Floppy Seek Enabled is enabled and
Boot Up NumLock Status On someone attempts
Typematic Rate Setting Disabled to write data into
Typematic Rate (Chars/Sec) 6 this area,BIOS
Typematic Delay (Msec) 250 will show a
Security Option Setup warning message
OS Select For DRAM >64MB Non-OS2 on screen and
Video BIOS Shadow Enabled alarm beep
C8000-CBFFF Disabled
CC000-CFFFF Disabled
D0000-D3FFF Disabled
D4000-D7FFF Disabled
D8000-DBFFF Disabled
DC000-DFFFF Disabled
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
Virus Warning
This option allows you to choose the VIRUS Warning
feature for IDE Hard Disk boot sector protection. If this
function is enabled and someone attempts to write data into
this area, BIOS will show a warning message on screen and
alarm beep.
The Choices: Enabled(default), Disabled.
1-101-10
1-10
1-101-10
Page 37
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
CPU Internal Cache
These two categories speed up memory access. However,
it depends on CPU/chipset design.
Enabled (default) Enabled cache.
Disabled Disabled cache.
External Cache
This fields allow you to Enable or Disable the CPU’S
“Level 2” secondary cache. Caching allows better
performance.
Enabled (default) Enabled cache.
Disabled Disabled cache.
CPU L2 Cache ECC Checking
The item allows you to enable/disable CPU L2 Cache ECC
Checking.
The Choices: Enabled(default), Disabled.
Processor Number Feature
The item will show up when you install the Pentium III
processor.
Enabled (default) Pentium Processor Number
Feature.
Disabled Disabled.
Quick Power On Self Test
This category speeds up Power on Self-Test(POST) after
you power up the computer. If it is set to Enable, BIOS
will shorten or skip some check items during POST.
Enabled Enabled quick POST.
Disabled (default) Normal POST.
First/Secondary/Third Boot Device
This BIOS attempts to load the operating system from
the devices in the sequence selected in these items.
The Choices: Floppy, LS120, HDD-0, SCSI, CDROM,
HDD-1, HDD-2, HDD-3, ZIP100, LAN, Disabled.
1-111-11
1-11
1-111-11
Page 38
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Boot Other Device
The Choices: Enabled(default), Disabled.
Swap Floppy Drive
If the system has two floppy drives, you can swap the
logical drive name assignments.
The Choices: Disabled(default), Enabled.
Boot Up Floppy Seek
Seek disk drives during boot up. Disabled speeds boot-up.
The Choices: Enabled(default), Disabled.
Boot Up NumLock Status
Select power on state for Numlock.
On (default) Numpad is number keys.
Off Numpad is arrow keys.
Gate A20 Option
Select if chipset or keyboard controller should control
Gate A20.
Normal A pin in the keyboard
controller controls Gate A20.
Fast (default) Lets chipset control Gate A20.
Typematic Rate Setting
Enabled Enabled this option to adjust
the keystroke repeat rate.
Disabled (default) Disabled.
Typematic Rate (Char/Sec)
Range between 6(default) and 30 characters per second.
This option controls the speed of repeating keystrokes.
Typematic Delay (Msec)
This option sets the time interval for displaying the first
and the second characters.
The Choices: 250(default), 500, 750, 1000
1-111-11
1-11
1-111-11
Page 39
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Security Option
This category allows you to limit access to the system and
Setup, or just to Setup.
System The system will not boot and
access to Setup will be denied
if the correct password is not
entered in prompt.
Setup (default) The system will boot, but
access to Setup will be denied
if the correct password is not
entered in prompt.
OS Select For DRAM
Select the operating system that is running with greater
than 64MB of RAM on the system.
The Choices: Non-OS2(default), OS2
Video BIOS Shadow
Determines whether video BIOS will be copied to RAM
for faster execution.
Enabled (default) Optional ROM is enabled.
Disabled Optional ROM is disabled.
C8000-CFFFF Shadow / D0000-DFFFF Shadow
Determines whether video BIOS will be copied to RAM
for faster execution.
Enabled Optional ROM is Shadowed.
Disabled (default) Optional ROM is not
Shadowed.
Note: For C8000-DFFFF option-ROM on PCI BIOS,
BIOS will automatically enable the shadow RAM. User
does not have to select the item.
1-121-12
1-12
1-121-12
Page 40
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.4 Advanced Chipset Features
This section allows you to configure the system based on
the specific features of the installed chipset. This chipset
manages bus speeds and access to system memory resources,
such as DRAM and external cache. It also coordinates
communications of the PCI bus. It must be stated that these
items should never need to be altered. The default settings
have been chosen because they provide the best operating
conditions for your system. The only time you might
consider making any changes would be if you discovered that
data was lost while using your system.
◎◎
◎ Figure 4. Advanced Chipset Features
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Advanced Chipset Features
DRAM Timing By SPD Enabled Item Help
DRAM Clock Host CLK
SDRAM Cycle Length 3 Menu Level
Bank Interleave Disabled
Memory Hole Disabled
P2C/C2P Concurrency Enabled
System BIOS Cacheable Disabled
Video RAM Cacheable Disabled
AGP Aperture Size 64M
AGP-4X Mode Enabled
AGP Driving Control Auto
AGP Driving Value DA
AGP Fast Write Disabled
On Chip USB Enabled
USB Keyboard Support Disabled
USB Mouse Support Disabled
On Chip Sound Auto
On Chip Modem Auto
CPU to PCI Write Buffer Enabled
PCI Dynamic Bursting Enabled
PCI Master 0 WS Write Enabled
PCI Delay Transaction Enabled
PCI #2 Access #1 Retry Enabled
AGP Master 1WS Write Disabled
AGP Master 1WS Read Disabled
Memory Parity /ECC Check Disabled
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-141-14
1-14
1-141-14
Page 41
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
DRAM Timary By SPD
The Choices: Enabled(default), Disabled.
DRAM Clock
This item determines DRAM Clock following the CPU
host clock.
The Choices: Host CLK(default), Host CLK+33M, Host
CLK-33M.
SDRAM Cycle Length
When synchronous DRAM is installed, the number of
clock cycle of CAS latency depends on the DRAM timing.
Do not reset this field from the default value specified by
the system designer.
The Choices: 3(default), 2, Auto.
Memory Hole
In order to improve performace, certain space in memory
can be reserved for ISA cards. This memory must be
mapped into the memory's space below 16MB.
The Choices: Diasbled(default), Enabled.
P2C/C2P Concurrency
The item allows you to enable/disable the PCI to CPU to
PCI concurrency.
The Choices: Enabled(default), Disabled.
System BIOS Cacheable
When enabled, the access to the system BIOS ROM
address at F0000H-FFFFFFH is cached.
The Choices: Disabled(default), Enabled.
Video RAM Cacheable
Enabled Enabled Video RAM
Cacheable.
Disabled (default) Disabled Video RAM
Cacheable.
1-151-15
1-15
1-151-15
Page 42
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
AGP Aperture Size
Select the size of the Accelerated Graphic Port(AGP)
aperture. The aperture is a portion of the PCI memory
address range dedicated for graphics memory address
space. Host cycle that hit the aperture range are forwarded
to the AGP without any translation.
The Choices: 64M(default), 32M, 16M, 8M, 4M,128M.
AGP-4X Mode
The item allows you to enable/disable the AGP-4X Mode.
The Choices: Enabled(default), Disabled.
AGP Driving Control
By choosing “Auto” the system BIOS will enable the AGP
output Buffer Drive strength that were defined by AGP
Card. By choosing “Manual”, it allows user to set AGP
output Buffer Drive strength by manual.
The Choices: Auto(default), Manual.
AGP Driving Value
This item allows you to adjust the AGP driving force.
The Choices: Min=0000~Max=00FF.
AGP Fast Write
It allows you to enable/disable the AGP fast write.
The Choices: Disabled(default), Enabled.
On Chip USB
This should be enabled if your system has a USB installed
on the system board and you wish to use it. Even when so
equipped, if you add a higher performance controller, you
will need to disable this feature.
The Choices: Enabled(default), Disabled.
1-161-16
1-16
1-161-16
Page 43
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
USB Keyboard Support
Select Enabled if your system contains a Universal Serial
Bus(USB) controller and you have a USB keyboard.
The Choices: Disabled(default), Enabled.
On Chip Sound
The default setting of this item unilizes an onboard sound
chip for audio output. There is no need to buy and insert a
sound card. If a sound card is installed, disable this item.
The Choices: Auto(default), Disabled
On Chip Modem
The item allows you to control the onboard MC97
Modem controller.
The Choices: Auto(default), Disabled.
CPU to PCI Write Buffer
When this field is Enabled, write from the CPU to the PCI
bus are buffered, to compensate for the speed differences
between the CPU and the PCI bus. When Disabled, the are
not buffered and the CPU must wait until the write is
complete before starting another write cycle.
The Choices: Enabled(default), Disabled.
PCI Dynamic Bursting
The Choices: Enabled(default), Disabled.
PCI Master 0 WS Write
When this field is Enabled, write data to the PCI bus are
executed with zero wait states.
The Choices: Enabled(default), Disabled.
PCI Delay Transaction
The Choices: Enabled(default), Disabled.
1-171-17
1-17
1-171-17
Page 44
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
PCI #2 Access #1 Retry
The Choices: Enabled(default), Disabled.
AGP Master 1WS Write
When Enabled, write data to the AGP (Accelerated
Graphic Port) that will be executed with one wait states.
The Choices: Disabled(default), Enabled.
AGP Master 1WS Read
When Enabled, read data to the AGP (Accelerated Graphic
Port) that will be executed with one wait states.
The Choices: Disabled(default), Enabled.
1-181-18
1-18
1-181-18
Page 45
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.5 Integrated Peripherals
◎◎
◎ Figure 5. Integrated Peripherals
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Integrated Peripherals
On-Chip IDE Channel 0 Enabled Item Help
On-Chip IDE Channel 1 Enabled
IDE Prefetch Mode Enabled Menu Level
Primary Master PIO Auto
Primary Slave PIO Auto
Secondary Master PIO Auto
Secondary Slave PIO Auto
Primary Master UDMA Auto
Primary Slave UDMA Auto
Secondary Master UDMA Auto
Secondary Slave UDMA Auto
Init Display First PCI Slot
IDE HDD Block Mode Enabled
Onboard FDC Controller Enabled
Onboard Serial Port 1 Auto
Onboard Serial Port 2 Auto
UART 2 Mode Standard
IR Function Duplex Half
RxD,TxD Active No,Yes
Onboard Parallel Port 378/IRQ7
Onboard Parallel Mode Normal
ECP Mode Use DMA 3
Parallel Port EPP Type EPP1.9
Onboard Legacy Audio Enabled
Sound Blaster Disabled
SB I/O Base Address 220H
SB IRQ Select IRQ 5
SB DMA Select DMA1
MPU - 401 Disabled
MPU - 401 I/O Address 330-333H
Game Port (200-270H) Enabled
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-191-19
1-19
1-191-19
Page 46
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
On-Chip IDE Channel 0
Enabled (default) Enabled onboard 1st channel
IDE port.
Disabled Disabled onboard 1st channel
IDE port.
On-Chip IDE Channel 1
Enabled (default) Enabled onboard 2nd channel
IDE port.
Disabled Disabled onboard 2nd channel
IDE port.
IDE Prefetch Mode
The onboard IDE drive interface supports IDE prefetching,
for faster drive access. If you install a primary and or
secondary add-in IDE interface, set this field to Disabled if
the interface does not support prefetching.
The Choices: Enabled(default), Disabled.
Primary Master PIO(for onboard IDE 1st channel)
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Mode 0~4 Manually set the IDE
Accessing mode.
Primary Slave PIO(for onboard IDE 2nd channel)
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Mode 0~4 Manually set the IDE
Accessing mode.
Secondary Master PIO(for onboard IDE 1st channel)
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Mode 0~4 Manually set the IDE
Accessing mode.
1-101-10
1-10
1-101-10
Page 47
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Secondary Slave PIO(for onboard IDE 2nd channel)
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Mode 0~4 Manually set the IDE
Accessing mode.
Primary Master UDMA
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Disabled Disabled.
Primary Slave UDMA
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Disabled Disabled.
Secondary Master UDMA
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Disabled Disabled.
Secondary Slave UDMA
Auto (default) BIOS will automatically detect
the IDE HDD Accessing mode.
Disabled Disabled.
Init Display First
PCI Slot (default) Set Init Display First to PCI
Slot.
Onboard AGP Set Init Display First to
onboard AGP.
1-111-11
1-11
1-111-11
Page 48
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
IDE HDD Block Mode
Enabled (default) Enabled.
Disabled Disabled.
Onboard FDC Controller
Enabled (default) Enabled.
Disabled Disabled.
Onboard Serial Port1/Port2
Select an address and corresponding interrupt for the first
and second serial ports.
The Choices: Auto(default), (3F8/IRQ4), (2F8/IRQ3),
(3E8/IRQ4), (2E8/IRQ3).
UART 2 Mode
This item allows you to select which Infra Red(IR)
function of the onboard I/O chip you wish to use.
The Choices: Standard (default), SCR, ASKIR.
IR Function Duplex
This item allows you to select which Infra Red(IR)
function of the onboard I/O chip you wish to use.
The Choices: Half (default), Full.
Parallel Port Mode
Normal (default)
SPP Using Parallel port as Standard
Parallel Port.
EPP Using Parallel port as Ex-
hancedParallel Port.
ECP Using Parallel port as Ex-
tended Capabilites Port.
ECP/EPP Using Parallel port as
ECP/EPP mode.
1-111-11
1-11
1-111-11
Page 49
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Onboard Parallel Port
This item allows you to select the I/O address with which
to access the onboard parallel port controller.
Disabled.
3BC/IRQ7.
378/IRQ7. (default)
278/IRQ5.
Onboard Legacy Audio
The Choices: Enabled(default), Disabled.
Sound Blaster
The Choices: Disabled(default), Enabled.
SB I/O Base Address
Change the SoundBlaster Pro Base I/O Address
settings.
SB IRQ Select
Change the SoundBlaster Pro interrupt signal.
SB DMA Select
Change the SoundBlaster Pro direct memory access
setting.
MPU -401
The Choices: Disabled(default), Enabled.
MPU -401 I/O Address(330-333H)
Change the SoundBlaster Pro MPU-401 I/O address.
Game Port (200-270H)
Change the joystick connection address.
The Choices: Enabled(default), Disabled.
1-121-12
1-12
1-121-12
Page 50
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.6 Power Management Setup
The Power Management Setup allows you to configure your
system to most effectively save energy while operating in a
manner consistent with your own style of computer use.
◎◎
◎ Figure 6. Power Management Setup
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Power Management Setup
ACPI Function Enabled Item Help
Power Management Press Enter
ACPI Suspend Type S1(POS) Menu Level
PM Control by APM Yes
Video Off Option Suspend->Off
Video Off Method V/H SYNC+Blank
Modem Use IRQ 3
Soft-Off by PWRBTN Instant-Off
State After Power Failure Of f
Wake Up Events Press Enter
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Power Management
Power Management User Define Item Help
HDD Power Down Disabled
Doze Mode Disabled Menu Level
Suspend Mode Disabled
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-141-14
1-14
1-141-14
Page 51
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
ACPI Function
This item display status of the Advanced Configuration and
Power Management (ACPI).
Power Management
This category allows you to select the type (or degree) of
power saving and is directly related to the following
modes.
1. HDD Power Down.
2. Doze Mode.
3. Suspend Mode.
If you highlight the “Press Enter” next to the “Power
Management” label and then press the enter key, it will
take you to a submenu with the following options:
Power Management
This option allows you to set each mode individually.
When not disabled, each of the ranges are from 1 min. to 1
hr. except for HDD Power Down which ranges from 1 min.
to 15 min. and disable.
The Choices: User Define (default), Min Saving, Max
Saving.
HDD Power Down
By default, this is “Disabled”, meaning that no matter the
mode of the rest of the system, the hard drive will remain
ready. Otherwise, you have a range of choices from 1 to
15 minutes or Suspend. This means that you can select to
have your hard disk drive be turned off after a selected
number of minutes or when the rest or the system goes
into a suspend mode.
The Choices: Disabled(default).
Doze Mode/Suspend Mode
The Doze Mode, and Suspend Mode fields set the Period
of time after each of these modes activates. At Max
Saving, these modes activate sequentially (in the given
order) after one minute; at Min Saving after one hour.
The Choices: Disabled(default).
1-151-15
1-15
1-151-15
Page 52
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
ACPI Suspend Type
The item allows you to select the suspend type under ACPI
operating system.
S1(POS) (default) Power on Suspend.
S3(STR) Suspend to RAM.
PM Control by APM
No System BIOS will ignore APM
when Power Management is
on.
Yes (default) System BIOS will wait for
APM’S prompt before it enters
any PM mode.
Video Off Option
This field determines when to activate the video off feature
for monitor power management.
The Choices: Suspend->off(default), Always on.
Video Off Method
This determines the manner in which the monitor is
blanked.
V/H SYNC+Blank This selection will cause the
(default) system to turn off the vertical
and horizontal synchronization
ports and write blanks to the
video buffer.
Blank Screen This option only writes blanks
to the video buffer.
DPMS Support Initial display power
management signaling.
Modem Use IRQ
This determines the IRQ, which can be applied in Modem
use.
4 (default)
3/5/7/9/10/11/NA
1-161-16
1-16
1-161-16
Page 53
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Soft-Off by PWRBTN
Pressing the power button for more than 4 seconds forces
the system to enter the Soft-Off state when the system has
“hung”.
The Choices: Instant-Off(default), Delay 4 Sec.
State After Power Failure
This option will determine how the system will power on
after a power failure.
The Choices: Off(default), On, Auto.
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Wake Up Events
VG A OFF Item Help
LPT & COM LPT/COM
HDD & FDD ON Menu Level
PCI Master OFF
Wake Up On LAN/Ring Disabled
RTC Alarm Resume Disabled
Date (of Month) 0
Resume Time (hh:mm:ss) 0 0 0
Primary INTR ON
IRQs Activity Monitoring Press Enter
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
IRQ Activity Monitoring
IRQ 3 (COM2) Enabled Item Help
IRQ 4 (COM1) Enabled
IRQ 5 (LPT2) Enabled Menu Level
IRQ 6 (Flppy Disk) Enabled
IRQ 7 (LPT1) Enabled
IRQ 8 (RTC Alarm) Disabled
IRQ 9 (IRQ2 Redir) Disabled
IRQ 10 (Reserved) Disabled
IRQ 11 (Reserved) Disabled
IRQ 12 (PS2/Mouse) Enabled
IRQ 13 (Coprocessor) Enabled
IRQ 14 (Hard Disk) Enabled
IRQ 15 (Reserved) Disabled
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
1-171-17
1-17
1-171-17
Page 54
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Wake Up Events
If you highlight the “Press Enter” next to the “Wake Up
Events” label and then press the enter key, it will take you
to a submenu with the following options:
VGA
When set to On, any event occurring at a VGA port will
awaken a system which has been powered down.
LPT & COM
When set to On, any event occurring at a COM(serial) /
LPT (printer) port will awaken a system which has been
powered down.
HDD & FDD
When set to On(default), any event occurring at a hard or
floppy drive will awaken a system which has been powered
down.
PCI Master
When set to On, any event occurring at a PCI port will
awaken a system which has been powered down.
Wake up On LAN/Ring
To use this function, you need a LAN add-on card which
supports power on function. It should also support the
wake-up on LAN jump.
The Choices: Disabled(default).
RTC Alarm Resume
When “Enabled”, you can set the date and time at which the
RTC (real-time clock) alarm awakens the system from
Suspend mode.
1-181-18
1-18
1-181-18
Page 55
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Primary INTR
When set to On(default), any event occurring at Primary
INTR will awaken a system which has been powered
down.
The following is a list of IRQ, Interrupt ReQuests, which
can be exempted much as the COM ports and LPT ports
above can. When an I/O device wants to gain the attention
of the operating system, it signals this by causing an IRQ
to occur. When the operating system is ready to respond
to the request, it interrupts itself and performs the service.
As above, the choices are On and Off. Off is the default.
When set On, activity will neither prevent the system from
going into a power management mode nor awaken it.
IRQ3 (COM1)
IRQ4 (COM2)
IRQ5 (LPT2)
IRQ6 (Floppy Disk)
IRQ7 (LPT1)
IRQ8 (RTC Alarm)
IRQ9 (IRQ2 Redir)
IRQ10 (Reserved)
IRQ11 (Reserved)
IRQ12 (PS/2 Mouse)
IRQ13 (Coprocessor)
IRQ14 (Hard Disk)
IRQ15 (Reserved)
1-191-19
1-19
1-191-19
Page 56
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI
or Personal Computer Interconnect,is a system which allows
I/O devices to operate at speeds nearing the speed of the
CPU itself uses when communicating with its own special
components. This section covers some very technical items
and it is strongly recommended that only experienced uses
should make any changes to the default settings.
◎◎
◎ Figure 7. PnP/PCI Configurations
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
PnP/PCI Configurations
PNP OS Installed No Item Help
Reset Configuration Data Disabled Menu Level
Resources Controlled By Auto(ESCD) Select Yes if
IRQ Resources Press Enter you are using a
DMA Resources Press Enter Plug and Play
PCI/VGA Palette Snoop Disabled select No if you
Assign IRQ For VGA Enabled need the BIOS
Assign IRQ For USB Enabled to configure non-
capable
operating system
boot devices
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
PNP OS Installed
When set to YES, BIOS will only initialize the PnP cards
used for booting (VGA, IDE, SCSI). The rest of the cards
will be initialized by the PnP operating system like
Windows 95. When set to No, BIOS will initialize all the
PnP cards. Therefore for non-PnP operating systems
(DOS, Netware), this option must be set to No.
1-201-20
1-20
1-201-20
Page 57
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Reset Configuration Data
The system BIOS supports the PnP feature so the system
needs to record which resource is assigned and proceeds
resources from conflict. Every peripheral device has a
node, which is called ESCD. This node records which
resources are assigned to it. The system needs to record
and update ESCD to the memory locations. These
locations (4K) are reserved at the system BIOS.
If Disabled (Default)is chosen, the system’s ESCD will
update only when the new configuration varies from the
last one. If Enabled is chosen, the system is forced to
update ESCDs and then is automatically set to the
“Disabled” mode.
IRQ3 assigned to:PCI/ISA PnP
IRQ4 assigned to:PCI/ISA PnP
IRQ5 assigned to:PCI/ISA PnP
IRQ7 assigned to:PCI/ISA PnP
IRQ9 assigned to:PCI/ISA PnP
IRQ10 assigned to:PCI/ISA PnP
IRQ11 assigned to:PCI/ISA PnP
IRQ12 assigned to:PCI/ISA PnP
IRQ14 assigned to:PCI/ISA PnP
IRQ15 assigned to:PCI/ISA PnP
DMA-0 assigned to:PCI/ISA PnP
DMA-1 assigned to:PCI/ISA PnP
DMA-3 assigned to:PCI/ISA PnP
DMA-5 assigned to:PCI/ISA PnP
DMA-6 assigned to:PCI/ISA PnP
DMA-7 assigned to:PCI/ISA PnP
1-211-21
1-21
1-211-21
Page 58
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
The above settings will be shown on the screen only if
“Manual” is chosen for the resources controlled by
function.
Legacy is the term which signifies that a resource is
assigned to the ISA Bus and provides for non-PnP ISA
add-on cards. PCI/ISA PnP signifies that a resource is
assigned to the PCI Bus or provides for ISA PnP add-on
cards and peripherals.
Resources Controlled By
By Choosing “Auto” (default), the system BIOS will detect
the system resources and automatically assign the relative
IRQ and DMA channel for each peripheral. By Choosing
“Manual” the user will need to assign IRQ & DMA for
add-on cards. Be sure that there are no IRQ/DMA and I/O
port conflicts.
IRQ Resources
When resources are controlled manually, assign each
system interrupt a type, depending on the type of device
using the interrupt.
DMA Resources
When resources are controlled manually, assign each
DMA channel a type, depending on the type of device
using the DMA channel.
1-211-21
1-21
1-211-21
Page 59
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
PCI / VGA Palette Snoop
Choose Disabled or Enabled. Some graphic controllers
which are not VGA compatible take the output from a VGA
controller and map it to their display as a way to provide
boot information and VGA compatibility.
However, the color information coming from the VGA
controller is drawn from the palette table inside the VGA
controller to generate the proper colors, and the graphic
controller needs to know what is in the palette of the VGA
controller. To do this, the non-VGA graphic controller
watches for the write access to the VGA palette and
registers the snoop data. In PCI based systems, the Write
Access to the palette will not show up on the ISA bus if the
PCI VGA controller responds to the Write.
In this case, the PCI VGA controller should not respond to
the Write, it should only snoop the data and permit the
access to be forwarded to the ISA bus. The non-VGA ISA
graphic controller can then snoop the data on the ISA bus.
Unless you have the above situation, you should disable
this option.
Disabled (default) Function Disabled.
Enabled Function Enabled.
Assign IRQ For VGA
Lets the user choose which IRQ to assign for the VGA.
Assign IRQ For USB
Lets the user choose which IRQ to assign for the USB.
1-221-22
1-22
1-221-22
Page 60
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.8 PC Health Status
◎◎
◎ Figure 8. PC Health Status
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
PC Health Status
Current CPU Temp. 36℃ /96℉ Item Help
Current System Temp. ℃/32℉
Current CPU Fan1 Speed 5120RPM Menu Level
Current CPU Fan2 Speed 0RPM
Vcore 1.53V
2.5V 2.50V
3.3V 3.28V
5V 5.00V
12V 11.76V
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
Current CPU Temp.
This field displays the current CPU temperature, if your
computer contains a monitoring system.
Current System Temp.
This field displays the current system temperature, if your
computer contains a monitoring system.
Current CPUFan1 Speed
These field displays the current speed of up to CPU Fans,
if your computer contains a monitoring system.
Current CPUFan2 Speed
These field displays the current speed of up to System
Fans, if your computer contains a monitoring system.
Current CPU Vcore , 2.5V, 3.3V, 5V, 12V
Detect system’s voltage status automatically.
1-241-24
1-24
1-241-24
Page 61
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.9 Frequency / Voltage Control
◎◎
◎ Figure 9. Frequency / Voltage Control
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Frequency / Voltage Control
Auto Detect DIMM / PCI CLK Enabled Item Help
Spread Spectrum Modulated Disabled
CPU Host Clock Default Menu Level
←→↑↓: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F1:General Help F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
Auto Detect DIMM / PCI CLK
This item allows you to enable/disable auto detect DIMM /
PCI CLOCK.
The Choices: Enabled(default), Disabled.
Spread Spectrum Modulated
This function is designed to EMI test only.
The Choices: Disabled(default), Enabled.
CPU Host Clock
This item allows you to select CPU Host Clock .
The Choices: 66~166MHz(default).
you can key in DEC number.
1-251-25
1-25
1-251-25
Page 62
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.10 Load Fail-Safe Defaults
When you press <Enter> on this item, you get a
confirmation dialog box with a message similar to:
◎◎
◎ Figure 10. Load Fail-Safe Defaults
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configuration Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
Pressing ‘Y’ loads the default values that are factory settings
for optimal performance of system operations.
Load Fail-Safe Default (Y/N)? N
Time , Date , Hard Disk Type ...
1-261-26
1-26
1-261-26
Page 63
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.11 Load Optimized Defaults
When you press <Enter> on this item, you get a
confirmation dialog box with a message similar to:
◎◎
◎ Figure 11. Load Optimized Defaults
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configuration Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
Pressing ‘Y’ loads the default values that are factory settings
for optimal performance of system operations.
Load Optimized Default (Y/N)? N
Time , Date , Hard Disk Type ...
1-271-27
1-27
1-271-27
Page 64
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.12 Set Supervisor / User Password
◎◎
◎ Figure 12. Set Supervisor / User Password
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configuration Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
When you select this function, the following message will
appear at the center of the screen to assist you in creating a
password.
Type a password, up to eight characters, and press <Enter>.
The password you type now will clear any previously entered
password from CMOS memory. You will be asked to
confirm the password. Type the password again and press
<Enter>. You may also press <ESC> to abort the selection
and not enter a password. To disable the password, just press
<Enter> when you are prompted to enter a password. A
message will confirm that you wish to disable the password.
Once the password is disabled, the system will boot and you
can enter setup freely.
Enter Password:
Time , Date , Hard Disk Type ...
Enter Password
1-281-28
1-28
1-281-28
Page 65
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Password Disabled
If you select “System” at the Security Option of BIOS
Features Setup Menu, you will be prompted for the
password every time when the system is rebooted, or any
time when you try to enter Setup. If you select “Setup” at the
Security Option of the BIOS Features Setup Menu, you will
be prompted only when you try to enter Setup.
1-291-29
1-29
1-291-29
Page 66
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.13 Save & Exit Setup
◎◎
◎ Figure 13. Save & Exit Setup
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configuration Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
Typing “Y” will quit the Setup Utility and save the user setup
value to RTC CMOS RAM.
Typing “N” will return to the Setup Utility.
Save & Exit Setup (Y/N)? Y
Time , Date , Hard Disk Type ...
1-401-40
1-40
1-401-40
Page 67
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett p
Bhapter 1 BIOS Sett pBhapter 1 BIOS Sett p
2.14 Exit Without Saving
◎◎
◎ Figure 14. Exit Without Saving
◎◎
CMOS Setup Utility-Copyright (C) 1984-2001 Award Software
Standard CMOS Features Frequency/Voltage Control
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Supervisor Password
Power Management Setup Set User Password
PNP/PCI Configuration Save & Exit Setup
PC Health Status Exit Without Saving
Esc : Quit F9 : Menu in BIOS ←→↑↓: Select Item
F10 : Save & Exit Setup
Typing “Y” will quit the Setup Utility without saving to RTC
CMOS RAM.
Typing “N” will return to the Setup Utility.
Exit Without Saving (Y/N)? Y
Time , Date , Hard Disk Type ...
1-411-41
1-41
1-411-41
Page 68
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
Chaoser 3 Cr h ver Inrsallashnn
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
3. Driver Installation
Introduction
There are motherboard drivers and utilities included in
ACORP Bonus CD disc. You don't need to install all of them
in order to boot your system. But after you finish the
hardware installation, you have to install your operation
system first (such as windows 98) before you can install any
drivers or utilities. Please refer to your operation system
installation guide.
Note
:Please follow recommended procedure
to install Windows 95 and Windows 98.
3.1 Auto-run Menu
You can use the auto-run menu of Bonus CD disc.
Choose the utility or driver and select model name.
3-13-1
3-1
3-13-1
Page 69
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
Chaoser 3 Cr h ver Inrsallashnn
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
3.2 Installing VIA 4 in 1 Driver
You can install the VIA 4 in 1 driver (IDE Bus master
(For Windows NT use), VIA ATAPI Vendor Support
Driver, VIA AGP, IRQ Routing Driver (For Windows 98
use), VIA Registry (INF) Driver) from the Bonus Pack
CD disc auto-run menu.
(1)
Click
"VIA Driver" Item.
(2)
Click
"Chipset_driver" Item.
3-23-2
3-2
3-23-2
(3)
Click
"4in1432v(a)" Item.
Page 70
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
Chaoser 3 Cr h ver Inrsallashnn
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
(2)
Click
"Setup" Item.
(5)
Click "Next".
Note:
Installing this Bus Master
IDE driver may cause Suspend
to Hard Drive failure.
3.3 Installing Audio Driver
This motherboard comes with an AC97 CODEC and the
sound controller is in VIA South Bridge chipset. You can
find the audio driver from the Bonus Pack CD disc auto-
run menu.
3-33-3
3-3
3-33-3
(1)
Click
"VIA Driver" Item.
Page 71
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
Chaoser 3 Cr h ver Inrsallashnn
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
(2)
Click
"Audio_driver" Item.
(3)
Click
"Via686A&B" Item.
3-33-3
3-3
3-33-3
(4)
Click "Setup".
Page 72
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
Chaoser 3 Cr h ver Inrsallashnn
Chaoser 3 Cr h ver InrsallashnnChaoser 3 C rh ver Inr sallashnn
(5)
3-53-5
3-5
3-53-5
Loading...