Acopian Power Supplies Data Sheet

Power Supplies

Don’t forget these facts about Acopian....

•Fast Shipping? Acopian invented it! For over half a century, Acopian has built and shipped millions of power supplies within 3-DAYS after receipt of order. And we still do today!

View our 3-DAY Shipping Promise: www.acopian.com/3dayship.html

•You ALWAYS talk to a real person when you call Acopian.

•Acopian power supplies last a very long time!

•You can email [e-mail] anytime for 24/7 product support.

•The Online System Builder (www.acopian.com/SystemBuilder) is a convenient way to

get your own custom power supply or power system (and most ship within 9 Days).

•You can order Acopian power supplies factory direct.

•ALL Acopian products are made in the USA.

POWER SUPPLIES

<![if ! IE]>

<![endif]>LINEAR REGULATED AC–DC

Plug-in

SINGLE OUTPUT &

WIDE ADJUST OUTPUT

LINEAR REGULATED AC-DC

•Shipped Within 3 Days

•All Models U.L. Recognized

•Five Year Warranty

An Acopian Plug-in power module can be installed in a matter of seconds. Simply plug it into a standard octal socket. (Threaded mounting holes are provided in the base for fastening the module when used in other than the upright position, or if subject to extreme vibration.) To replace a module - for example, where added circuitry calls for a higher current rating - just unplug the old, plug in the new. And as a result of years of product refinement, your Acopian Plug-in provides the highest reliability of any available series-regulated power supply.

STANDARD FEATURES

•May be used in series

•Delivers current surges without damage - to protect against prolonged overload and shorts, use of an input fuse is recommended

•No derating or additional heat sinking required

•Completely serviceable

•Lightweight

SPECIFICATIONS

Input Voltage: 105-125 VAC, 50-400 Hz, single phase.

Output Specifications: See table.

Polarity: Output floating; either positive or negative terminal may be grounded or floated up to 300 volts above ground.

Temperature Coefficient: 0.02%/°C (Typical).

Ambient Operating Temperature: –10 to +65°C. No derating required.

MIL Tested and Extended Temperature Range:

See page F48.

Storage Temperature: –55 to +85°C.

Installation: Plugs into standard 8-pin octal socket (see page H4). Four mounting holes (6-32) are provided in the base for fastening the module when used in other than the upright position, or if extreme vibration will be encountered.

PIN CONNECTIONS:

Standard model.

OPTIONS

Solder Terminals: All models can be furnished with solder terminals instead of the octal type plug. Contact factory or see web site for detailed information.

*H dimension includes HEATSINK on BS, US, WS, and HS case sizes.

	Case			H*					Approx.
	Size	L	W		M	V	J	Q	Weight
	AS	3.40	3.28	4.67	2.625	2.625	1.00	.66	2 lb.	8 oz.
	BS	3.40	3.28	5.33	2.625	2.625	1.00	.66	2 lb.	14 oz.
	TS	3.33	4.15	4.85	2.562	2.750	1.12	.62	3 lb.	6 oz.
	US	3.33	4.15	5.53	2.562	2.750	1.12	.62	3 lb.	8 oz.
	WS	3.40	5.02	5.53	2.562	3.562	1.12	.62	4 lb.	14 oz.
	HS	3.40	5.02	6.65	2.562	3.562	1.12	.62	5 lb.
All dimensions in inches.

Remote Output Adjustment: All models have a local voltage adjustment. When provision for remote (external) adjustment is also desired, add prefix “E” to model number. Example: Model 12J100 becomes Model E12J100.

Remote Sensing: Provision for remote sensing of the output voltage to compensate for drops in the load lines can be furnished. Add prefix “R” to model number when ordering. “R” power supplies have a local voltage adjustment and provision for remote (external) output adjustment.

230 Volt furnished for operation on inputs of 210 to 250 VAC, 50-400 Hz. Add suffix “–230” to model number. The “–230” option requires two additional days.

Overvoltage Protection: An internal preset overvoltage protector is available. To order, add prefix “V” to the model number.

	F43	Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com
		131 Loomis Street, Easton, PA 18045 • Phone: [phone] • FAX: [phone]
	211108

SINGLE OUTPUT

Nominal	Adjust	Output	Regulation		Ripple				Nominal		Adjust			Output		Regulation					Ripple					Case
Output	Range	Current			mV		Case		Output		Range			Current								mV
			Load	Line		Model										Load			Line					Model
Voltage	± V	Amps.	± %	± %	RMS		Size		Voltage			± V		Amps.		± %			± %			RMS				Size		<![if ! IE]> <![endif]>LINEAR
1	.25	.100	.25	.05	0.5	1J10	AS		32			1		.300		.05			.05			1		32J30		AS
1.5	.5	.750	.7	.05	1	1.5J75	AS		32			1		.500		.05			.05			1		32J50		AS
2.5	.5	.750	.7	.05	1	2.5J75	AS		32			1		.600		.1			.05			1		32J60		TS
3.3	.5	.750	.7	.05	1	3.3J75	AS		32			1		1.0		.1			.05			1		32J100		US
3.3	.5	1.0	.5	.05	1	3.3J100	AS		32			1		1.5		.1			.05			1		32J150		WS
3.3	.5	1.5	.5	.05	1	3.3J150	US		34			1		.500		.05			.05			1		34J50		AS
3.3	.5	2.0	.5	.05	1	3.3J200	WS		35			1		.500		.05			.05			1		35J50		AS
3.3	.5	3.0	.5	.05	1	3.3J300	WS		36			1		.300		.05			.05			1		36J30		AS		<![if ! IE]> <![endif]>REGULATED
3.3	.5	4.0	.5	.05	1	3.3J400	HS		36			1		.500		.05			.05			1		36J50		AS
4	1	.750	.4	.05	1	4J75	AS		36			1		.600		.1			.05			1		36J60		TS
4	.5	1.0	.5	.05	1	4J100	AS		36			1		.800		.1			.05			1		36J80		TS
5	1	.750	.4	.05	1	5J75	AS		36			1		1.0		.2			.05			1		36J100		US
5	.5	1.0	.5	.05	1	5J100	AS		36			1		1.5		.1			.05			1		36J150		WS
5	.5	1.5	.4	.05	1	5J150	US		38			1		.500		.05			.05			1		38J50		AS
5	.5	2.0	.5	.05	1	5J200	WS		38			1		1.0		.2			.05			1		38J100		US
5	.5	3.0	.5	.05	1	5J300	WS		40			1		.300		.05			.05			1		40J30		AS
5	.5	4.0	.5	.05	1	5J400	HS		40			1		.400		.1			.05			1		40J40		AS
5	.5	5.0	.7	.05	1	5J500	HS		40			1		.600		.1			.05			1		40J60			TS
6	1	.400	.15	.05	1	6J40	AS		40			1		1.0		.2			.05			1		40J100		US
6	1	.750	.3	.05	1	6J75	AS		42			1		.400		.1			.05			1		42J40		AS
6	1	1.0	.3	.05	1	6J100	AS		42			1		.600		.15			.05			1		42J60			TS
6	.5	2.0	.3	.05	1	6J200	WS		45			1		.400		.1			.05			1		45J40		AS		<![if ! IE]> <![endif]>AC
6	.5	3.0	.5	.05	1	6J300	WS		45			1		.600		.15			.05			1		45J60			TS
6	.5	4.0	.5	.05	1	6J400	HS		48			1		.300		.05			.05			1		48J30		AS
6	.5	5.0	.7	.05	1	6J500	HS		48			1		.400		.1			.05			1		48J40		AS		<![if ! IE]> <![endif]>–
8	1	.750	.2	.05	1	8J75	AS		48			1		.600		.15			.05			1		48J60			TS
8	1	1.0	.2	.05	1	8J100	AS		50			1		.300		.05			.05			1		50J30		AS		<![if ! IE]> <![endif]>DC
9	1	.750	.15	.05	1	9J75	AS		50			1		.500		.1			.05			1		50J50			TS
9	1	1.0	.2	.05	1	9J100	AS		55			1		.200		.05			.05			1		55J20		AS
9	1	1.5	.3	.05	1	9J150	US		60			1		.200		.05			.05			1		60J20		AS
9	.5	2.0	.2	.05	1	9J200	WS		60			1		.300		.05			.05			1		60J30		AS
10	1	.750	.15	.05	1	10J75	AS		60			1		.400		.05			.05			1		60J40			TS
10	1	1.0	.2	.05	1	10J100	AS		65			1		.100		.05			.05			1		65J10		AS
10	1	1.5	.25	.05	1	10J150	US		65			1		.300		.05			.05			1		65J30		AS
10	.5	2.0	.15	.05	1	10J200	WS		70			1		.200		.05			.05			1		70J20		AS
10	.5	3.0	.25	.05	1	10J300	HS		70			1		.300		.05			.05			1		70J30		AS
12	1	.750	.15	.05	1	12J75	AS		75			1		.200		.05			.05			1		75J20		AS
12	1	1.0	.1	.05	1	12J100	AS		80			1		.200		.05			.05			1		80J20		AS
12	1	1.5	.2	.05	1	12J150	US		90			1		.100		.05			.05			1		90J10		AS
12	.5	2.0	.1	.05	1	12J200	WS		90			1		.200		.05			.05			1		90J20		AS
12	.5	3.0	.25	.05	1	12J300	HS		95			1		.100		.05			.05			1		95J10		AS
15	1	.400	.1	.05	1	15J40	AS		95			1		.200		.05			.05			1		95J20			AS
15	1	.750	.15	.05	1	15J75	AS		100			1		.100		.05			.05			1		100J10			AS
15	1	1.0	.15	.05	1	15J100	AS		100			1		.200		.05			.05			1		100J20			AS
15	1	1.5	.2	.05	1	15J150	US		105			1		.100		.05			.05			1		105J10			AS
15	.5	2.0	.1	.05	1	15J200	WS		105			1		.200		.05			.05			1		105J20			AS
15	.5	3.0	.25	.05	1	15J300	HS		110			1		.100		.05			.05			1		110J10			AS
16	1	.400	.1	.05	1	16J40	AS		110			1		.200		.05			.05			1		110J20			AS
16	1	.750	.15	.05	1	16J75	AS		120			1		.100		.05			.05			1		120J10			AS
16	1	1.0	.15	.05	1	16J100	AS		120			1		.200		.05			.05			1		120J20			AS
18	1	.400	.1	.05	1	18J40	AS		125			1		.100		.05			.05			1		125J10			AS
18	1	.750	.15	.05	1	18J75	AS		125			1		.200		.05			.05			1		125J20			AS
18	1	1.0	.15	.05	1	18J100	US		130			1		.100		.05			.05			1		130J10			AS
18	.5	2.0	.1	.05	1	18J200	WS		130			1		.200		.05			.05			1		130J20			AS
20	1	.400	.1	.05	1	20J40	AS		140			1		.200		.05			.05			1		140J20			AS
20	1	.750	.15	.05	1	20J75	AS		150			1		.050		.05			.05			1		150J05			AS
20	1	1.5	.2	.05	1	20J150	WS		150			1		.200		.05			.05			1		150J20			AS
20	.5	2.0	.1	.05	1	20J200	WS		200			1		.100		.05			.05			1		200J10			AS
22	1	.400	.1	.05	1	22J40	AS					WIDE ADJUST OUTPUT
22	1	.750	.15	.05	1	22J75	AS
22	1	1.0	.15	.05	1	22J100	US			Shown below is a partial listing of models with increased voltage
22	1	1.5	.2	.05	1	22J150	WS			adjustment ranges. Contact the factory for information on other models.
22	.5	2.0	.1	.05	1	22J200	WS			Output			Output		Regulation					Ripple
24	1	.400	.05	.05	1	24J40	AS
24	1	.750	.1	.05	1	24J75	AS			Voltage			Current		Load		Line			mV				Model	Case
24	1	1.0	.1	.05	1	24J100	US			Range			Amps.		± %		± %			RMS					Size
24	1	1.5	.15	.05	1	24J150	WS			2 to 30			.300		.5		.05			1				J230	AS
24	.5	2.0	.1	.05	1	24J200	WS
										3 to 15			.400		.5		.05			1				J315	BS
25	1	.400	.05	.05	1	25J40	AS			4 to 10			1.5		.5		.05			1				J410	US
25	1	.750	.1	.05	1	25J75	AS
										5 to 15			2.0		.5		.1			5				J515	HS
25	1	1.0	.1	.05	1	25J100	US
										5 to 25			.100		.1		.05			1				J525	AS
25	1	1.5	.15	.05	1	25J150	WS			6 to 30			.200		.1		.05			1				J630	AS
25	.5	2.0	.1	.05	1	25J200	WS
										10 to 18			.600		.3		.05			1				J1018	BS
28	1	.400	.05	.05	1	28J40	AS
										10 to 40			.200		.1		.05			1				J1040	AS
28	1	.500	.05	.05	1	28J50	AS
										15 to 25			.500		.1		.05			1				J1525	BS
28	1	.750	.1	.05	1	28J75	TS
										15 to 30			.300		.1		.05			1				J1530	BS
28	1	1.0	.1	.05	1	28J100	US			16 to 24			.750		.15		.05			1				J1624	BS
28	1	1.5	.15	.05	1	28J150	WS
										18 to 30			.400		.1		.05			1				J1830	BS
28	.5	2.0	.1	.05	1	28J200	WS
										20 to 28			.500		.1		.05			1				J2028	BS
30	1	.400	.05	.05	1	30J40	AS			23 to 32			1.0		.15		.05			1				J2332	US
30	1	.500	.05	.05	1	30J50	AS
										24 to 32			.500		.1		.05			1				J2432	BS
30	1	.750	.1	.05	1	30J75	TS			24 to 40			.400		.1		.05			1				J2440	BS
30	1	1.0	.1	.05	1	30J100	US
										24 to 50			.250		.1		.05			1				J2450	AS
30	1	1.5	.15	.05	1	30J150	WS
										28 to 60			.250		.1		.05			1				J2860	BS
30	.5	2.0	.1	.05	1	30J200	WS
										30 to 70			.300		.1		.05			1				J3070	BS

	Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com	F44
	131 Loomis Street, Easton, PA 18045 • Phone: [phone] • FAX: [phone]
		211108

Plug-in Power Supplies

MIL TESTED and EXTENDED TEMP RANGE

(for Plug-in models on pages F43-F47)

SHIPPED WITHIN 3 DAYS

ALL MODELS U.L. RECOGNIZED

Ruggedized construction and capability for operation through an extended ambient temperature range of –20 to +71°C (without derating) are provided by Acopian MIL-option supplies. In all other respects they are identical to our standard Plug-in power supplies.

HOW TO ORDER:

Add prefix “MIL-” to standard model number.

Example: Model 6J200 becomes MIL-6J200.

MIL-option equivalents to all the models included on pages F39 through F42, except those housed in case size HS, have been tested to these specifications:

ALTITUDE: MIL-STD-810B, Method 500, Procedure II.

VIBRATION: MIL-STD-810B, Method 514, Procedure I, Curve D.

SHOCK: MIL-STD-810B, Method 516, Procedure I.

FUNGUS: (additional $25.00/output charge applies.) MIL-STD-810B, Method 508, Procedure I.

CONDUCTED EMI: MIL-I-6181D, Paragraph 4.3.1., Figure II.

RADIATED EMI: MIL-I-6181D, Paragraph 4.3.2.

SUSCEPTIBILITY TO CONDUCTED AND RADIATED EMI: MIL-I-6181D, Paragraph 4.3.4.

HIGH TEMPERATURE: MIL-STD-810B, Method 501, Procedure I.

LOW TEMPERATURE: MIL-E-5272C, Paragraph 4.2.2, Procedure II.

HUMIDITY: MIL-STD-810B, Method 507, Procedure I. SALT FOG: MIL-STD-810B, Method 509, Procedure I.

<![if ! IE]>

<![endif]>DC–AC REGULATED LINEAR

	Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com	F48
	131 Loomis Street, Easton, PA 18045 • Phone: [phone] • FAX: [phone]
		211108

MOUNTING KITS & SOCKETS

Mounting Kits for ‘Mini Encapsulated - with screw terminals’ power supplies:

WALL MOUNTING

Model EB4A

Use Mounting Kit EB4A to mount from the power supply side of the mounting surface, necessary when the other side of the mounting surface is inaccessible. This kit consists of an aluminum plate and four screws for attaching it to the power supply, effectively adding mounting flanges to any Mini Encapsulated power supply with screw terminals or any Mini DC-DC Converter with screw terminals.

<![if ! IE]> <![endif]>niEncapsulated Pow erSupply

<![if ! IE]> <![endif]>M

DIN RAIL MOUNTING

Model EB35DIN

Mounting Kit EB35DIN consists of an aluminum plate, with two DIN clips attached to it, and four screws for attaching the plate to the bottom of any Mini Encapsulated power supply with screw terminals or any Mini DC-DC Converter with screw terminals. The power supply can then be snapped onto a 35mm ‘top hat’ type of DIN rail.

Sockets for ‘Mini Encapsulated - PC Board mounting’ power supplies:

For use with PC board mounting Mini Linears and PC board mounting DC-DC Converters.

Each of these sockets has a sturdy phenolic base with gold plated teflon-insulated contacts.

Model ES-1

Model EL-1

Model ELW-1

For case sizes ES-10 and ESC-10

For case sizes EL-10, EL-13, EL-20 and ELC-10

For case sizes ELW-13 and ELW-20

<![if ! IE]>

<![endif]>INFO & PRODUCTS OTHER

Sockets for ‘Plug-In’ power supplies:

RETMA-numbered screw-type terminals simplify wiring and permit the use of wire terminals or bare wire, 12 to 20 guage. Rated at 300 volts RMS, 10 amp.

Model SL608	Model SL611
For 8-pin plugs.	For 11-pin plugs.

All dimensions in inches.	All dimensions in inches.

	Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com	H4
	131 Loomis Street, Easton, PA 18045 • Phone: [phone] • FAX: [phone]
		211108

ORDERING INFO / TERMS & CONDITIONS

ACOPIAN SELLS FACTORY DIRECT WORLDWIDE: We do not use representatives or distributors. Contact Acopian for technical information or a quote.

WARRANTY: Acopian power supplies are warranted to be free from defects in material and workmanship for a period of five years (encapsulated devices, for one year) from date of original shipment. Acopian’s obligation under this warranty is limited to repairing any power supply returned to the factory Service Department in Easton, PA or Melbourne, FL, and replacing any defective parts. Mini Encapsulated power supplies are not repairable. Authorization must be obtained from Acopian before a power supply may be returned for repair. Units must be well packed when shipping to Acopian; the repair of any damage incurred during shipment will be charged. Transportation charges are to be paid by the purchaser. A reinspection and handling charge will be applied to returned units found to have no defects. If a failure has been caused by misuse, operation in excess of specifications, or modification by the customer, repairs will be billed at cost; in such cases, a cost estimate will be submitted before work is started.

Acopian reserves the right to make changes or improvements in its products without incurring any obligation to install the same on products previously manufactured.

This warranty is in lieu of all other warranties, obligations, and liabilities, expressed or implied, and is the purchaser’s exclusive remedy. Acopian makes no warranty, either express or implied, of merchantability, fitness for a particular purpose or otherwise. In no event shall Acopian be liable whether in contract, tort, or negligence, for special, indirect, incidental or consequential damages of any kind, including loss of business or profits, or any other losses incurred by the purchaser or any third party, the Customer’s remedies being limited, at Acopian’s option, to replacement, repair or credit at the price on the date of claim.

The validity, performance and construction of all terms and conditions and any sale made by Acopian shall be determined by the law of Pennsylvania, without regard to its conflict of law principles, and all parties to the transaction expressly consent to the jurisdiction of such courts and consent to the venue of the Court of Common Pleas for Northampton County, Pennsylvania.

PRICES: The prices shown are F.O.B. our factory; Easton, PA or Melbourne, FL. (‘EXW Factory’ if outside the 50 United States.) All prices and specifications are subject to change without notice.

TERMS: Net 30 days, subject to credit approval. Visa, MasterCard and American Express also accepted.

SHIPPING: Location permitting, small shipments are made by United Parcel Service, FedEx, DHL (international orders) or by Parcel Post; larger shipments, by insured motor freight collect. Shipments can be made by air upon request. Risk of loss shall be F.O.B. Our Factory, even in cases where freight may be prepaid or allowed to destination by Acopian. If equipment is received in damaged condition, it is the customer’s responsibility to contact the carrier and file a claim for damages.

TIME FOR DELIVERY: The time for delivery quoted by Acopian is the time required to ship from our plants. We will not be liable for delays in delivery caused by any reason beyond our control, including but not limited to acts of God, casualty, civil disturbance, labor disputes, transportation or supply difficulties, or any interruption of our facilities, and the quoted time for delivery shall be extended during the continuance of such conditions and for a reasonable time thereafter. In no event will Acopian be liable for any premium transportation, reprocurement, or similar costs incurred by the Customer as a result of conditions beyond Acopian’s control resulting in Acopian’s inability to deliver product in accordance with customer’s requested delivery schedules.

QUANTITY DISCOUNTS: Discounts are available to quantity buyers and are dependent upon the order quantity and the manufacturing scheduling anticipated by the order, and apply only to the quantity and delivery ordered. Partial shipments are considered as separate orders for discounting purposes.

EXPORT ORDERS: A minimum export documentation charge of $60.00 applies. (A minimum charge of $25.00 applies on orders to certain U.S. territories requiring customs forms.)

MOISTURE/FUNGUS PROOFING: Power supplies can be furnished with a moisture and fungus resistant varnish applied to interior surfaces. To order, add the suffix letter F to the model number. This option requires two additional days and is not available on High Voltage, Mini Encapsulated, Rack Mounting, and Gold Box Switching models.

TAGGING: Add $10.00 to price.

TEST DATA: Cost, $35.00 or 2% of order, whichever is greater.

SPECIAL MODELS/MODIFICATIONS: Cataloged models can be altered at the factory to meet special requirements. Contact the Applications Engineering Department to discuss your needs.

PARTS: The designs used in Acopian power supplies utilize standard components to the greatest practical extent. When replacements are required, the types originally used, or their equivalents, can usually be obtained most quickly from a local electronic components distributor.

Special components, such as transformers, are stocked at the factory warehouses. Contact the Applications Engineering Department for information on the parts required, referencing the model number of the power supply, the circuit designation of the component, and a description.

PURCHASE ORDER ACCEPTANCE: Orders are accepted subject to Acopian’s Terms and Conditions. Any Terms and Conditions of any Purchaser’s order, agreement, or understanding which are in addition to or inconsistent with Acopian’s shall not be binding upon Acopian unless made in writing and accepted over the signature of an authorized officer of Acopian. Orders shall not be considered accepted until entered into production at our plant. Acopian reserves the right to refuse any order. All typographical and clerical errors are subject to correction by Acopian.

RETURNED GOODS: Acopian products are built on a per-order basis, and ordinarily no credit can be extended for their return. No goods will be accepted for return unless authorized in writing by Acopian.

CHANGES: The customer may, by a written notice, request changes within the general scope of the order, in the drawings, designs or specifications; method of shipment; and place of delivery. If any such change causes an increase or decrease in the cost, or the time required for the processing of any part of the order, an equitable adjustment shall be made in the price or delivery schedule, or both, and the order shall be modified in writing accordingly.

CANCELLATION: Suspension or cancellation of orders may be made only upon our written approval and on terms that will indemnify us against all loss.

OVERTIME: It is anticipated that any order will be processed during regular working hours on regular working days. If for any reason the Purchaser requests Acopian to process the order, or any portion of it, outside of such regular working hours, any overtime or other additional expense occasioned thereby shall be billed to and paid by the Purchaser as an extra cost. Acopian reserves the right to decline to process the order outside regular working hours.

CUSTOMER DELAY OF WORK: If the performance of all or any part of the work is delayed or interrupted by Customer’s failure to act within the time specified (or within a reasonable time if no time is specified) and such act is not expressed or implied by the order, an adjustment shall be made in the cost of performance of the order caused by such delay or interruption and the order modified in writing accordingly. Adjustment will also be made in the delivery or performance dates and any other contractual provisions affected by such delay or interruption.

GOVERNMENT SPECIFICATIONS: Pricing is based upon industrial-grade construction, marking, packing, and packaging. Exception is taken to any MIL specifications, and to any requirements for the use of special forms, documentation other than quoted, and Government Source Inspection. Acopian must decline to quote on any other basis.

APPLICATIONS ASSISTANCE: Questions regarding the specifications, features, and use of any Acopian product should be directed to the Applications Engineering Department. A staff of power supply specialists will be pleased to assist you.

ACOPIAN IS AN ISO 9001 CERTIFIED COMPANY

	Online Ordering and Instant Quotes for ALL Acopian power supplies at www.acopian.com	H8
	131 Loomis Street, Easton, PA 18045 • Phone: [phone] • FAX: [phone]
		211108

<![if ! IE]>

<![endif]>INFO & PRODUCTS OTHER