Acnodes RMWQ 8190 User Manual

Download

Page 1

User Manual

RMWQ8190: 8U 19” 1440x900 Widescreen Industrial Rackmount CCTV Monitor

RMWQ 8190

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All righ ts reserved. Product descripti on and product speci ficat ions are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 2

RMWQ 8190

Legal Information

First English printing, October 2002 Information in this document has been carefully checked for accuracy; howeve r, no guarantee is given to the correctness of the contents. The inform ation in this document is subject to change without notice. We are not liable for any injury or loss t hat results from the use of this equipment.

Safety Instructions

Please read all of these instructions carefully before you use the dev ice. Save this manual for future reference.

¦ Unplug equipment before c leaning. Don’t use liquid or spray detergent; use a moist cloth.

¦ Keep equipment away from excessive humidity and heat. Pre ferably, keep it in an air-conditioned environment with

temperatures not exceeding 40º Celsius (104º Fahrenheit).

¦ When installing, place the equipment on a sturd y, level surface to prevent it from accidentally falling and causing

damage to other equipment or injury to persons nearb y.

¦ When the equipment is in an open position, do not cove r, block or in any way obstruct the gap between it and the

po wer supply. Prop er air convection is necessary to keep it from overheating.

¦ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.

¦ If you are using a power co rd that didn’t ship with the equipment, ensure that it is rated for the voltage and current

labeled on the equipment’s electrical ratings la bel. The voltage rating on the cord should be higher t han the one listed

on the equipment’s ratings label.

¦ Observe all precautions an d warnings attached to the equipment.

¦ If you don’t intend on using the equipment for a l ong time, disconnect it from the power outlet to prevent being

damaged by transient over -voltage.

¦ Keep all liquids away from the e quipment to minimize the risk of accidental spillage. Liquid spilled on to the power

supply or on other hardware may cause damage, fire or electrical shock.

¦ Only qualified service personnel should open the chassis. Opening it yourself could damage the equipm ent and

invalidate its warranty.

¦ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.

What the warranty does not cover

¦ Any product, on which the serial number has been defaced, modified or removed.

¦ Damage, deterioration or malfunction resulting from:

? Accident, misuse, neglect, fire, water, lightning, o r other acts of nature, unauthorized product modification, or

failure to follow instructions supplied with the product.

? Repair or attempted repair by an yone not authorized by us.

? Any damage of the product due to shipment.

? Remov al or installation of the pr oduct.

? Causes external to the product, such as electric power fluctuation or failure.

? Use of supplies or parts not meeting our specifications.

? Normal wear and tea r.

? Any other causes which does not relate to a product defect.

¦ Removal, installation, and s et-up service charges.

Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the lim its for a Class B digital dev ice, pursuant to Part 15 of the F CC rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment g enerates, uses, and can radiate radio frequency energy and, if not instal led and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not oc cur in a particular installation. If this equipment does cause ha rmful interference to radio or television reception, which can be determined by turning the equipment o ff and on, t he user is encouraged t o try t o correct t he interference by one or more of the following measures:

¦ Re-position or relocate the receiving antenn a.

¦ Incre ase the separat ion between the equipment and receive r.

¦ Connect the equipment into an outlet on a circuit di fferent from that to which the receiver is connected.

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 3

Contents

< Part. 1 > RMWQ 8190

1.1 Package Content

1.2 Structure Diagram & Dimension

1.3 Installation

P.1 P.1 - 2 P.3

< Part. 2 > Specifications / OSD

2.1 Product Specifications

2.2 On-screen Display Operation ( OSD )

P.4 - 5 P.6

< Part. 3 > Options

3.1 48V, 24V or 12VDC power P.7

< Part. 4 >

Quad Display Connection & Operation

4.1 QD Connection

4.2 QD ALARM Connection & Operation

4.3 QD Remote Control Connection & Operation

4.4 QD OSD Operation

4.5 QD On-screen Menu

4.6 QD VCR Operation

4.7 QD Specification

P.8 P.9 - 10 P.11 - 15

P.16 P.17 - 19 P.20 P.21

RMWQ 8190

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 4

RMWQ 8190

Before Installation

¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface. ¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive

dust, dirt, heat, water, moisture and vibration.

Unpacking

The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediatel y.

How To Clean Your LCD Monitor

Caution :

¦ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or

plugging your monitor into an electrical outlet.

¦ When you clean your monito r, do not press down on the LCD screen. Pressing down on the screen can

scratch or damage your display. Pressure damage is not covered under warrant y.

¦ Use only cleansers m ade specifically for cleaning monitors and monitor screens. Cleansers not made to

clean monitors and monitor screens can scratch the LCD display or strip o ff the finish.

¦ Do not spray any kind of liquid directly onto the screen or case of your monito r. Spraying liquids directly

onto the screen or case can cause damage which is not covered under warrant y.

¦ Do not use paper towels or abrasive pads to clean your monito r. Using an abrasive pad or any wood based

paper product such as paper towels can scratch your LCD screen.

Cleaning Your Monitor

To clean your LCD safely, please follow these steps :

Disconnect the power cord.

Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.

Cleaning Tough Marks and Smudges

To remove tough marks and smudges, please follow these steps :

Disconnect the power cord.

Spray a small amount of non-abrasive cleanser on a microfi ber cloth.

Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your microfiber cloth first, not directly on the parts you are cleaning.

Gently wipe the surface. Use as little pressure as possible.

Wait until your monitor is completely dry before plugging it in and powering it up.

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 5

< P art 1 >

< 1.1 > Pac kage Content

RP -W 119 Q D un it X 1

- 6ft V G A cable X 1

- P owe r cord X 1

- M 6 scre w, cage nut & c up wash er X 8

T he above package conte nt is on ly for the p ure mo del ( VGA o nly ). It v ar ie s with op tion s su ch a s DC p owe r.

< 1.2 > Str ucture Dia gra m

1 LCD pane l

Instal latio n Slid e

LC D OSD me mbr ane

Quad d ispla y co ntrol me mbr ane

5 Thum b S c rew

RMWQ 8190

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 6

< 1.2 > Dimension

Front View

Side View

UNIT : mm

1mm = 0.03937 inch

Top View

Model

Product Dimension

(W x D x H)

Packing Dimension

(W x D x H)

Net

Weight

Gross

Weight

RP-119QD series

445 x 650 x 44 mm

17.5 x 23.6 x 1.73"

595 x 860 x 140 mm

23.4 x 33.9 x 5.5”

12.5 kg 28 lb

18.5 kg 41 lb

The weight is only for the pure models. It varies with accessories & options such as DC power.

RMWQ 8190

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 7

RMWQ 8190

< 1 .3 > Installation - H ow to install Ins tallatio n Slide s

St ep

¦ Ins ert th e l ef t a nd r ight re ar moun ting b ra cke ts into

the d ispla y d rawe r.

St ep

¦ M e as u re th e dep th of th e front a nd rear m oun ting r ails. ¦ Align ea c h rea r mo u nt ing b racke t to a su itab le len gt h.

Step

C om ple te the i nstallatio n

¦ Fi x t he d ispla y draw er into t h e r ack.

M6 sc re w, ca ge n u t & c up w a s her x 8 a r e pro v ided.

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 8

< Part 2 >

< 2.1 > Product Specifications

LCD Panel

Manufacturer

Panel Size ( diagonal )

19-inch Widescreen TFT color LCD

Display pixel ( dots x lines )

1440 x 900

Brightness ( typ. )

250

Contrast Ratio ( typ. )

1000:1

Color

16.7 M

Viewing Angle ( L/R/U/D )

80/80/80/80

Response Time ( ms )

Dot pitch ( mm )

0.2835

Display Area ( mm )

408.24H x 255.15V

Surface treatment

Haze 25%, Hard-coating

Surface hardness

Backlight Type

LED

MTBF ( hrs )

30,000

Video Connectivity

Analog

VGA

Analog 0.7Vp-p

Power

Power Supply

Range

Auto-sensing 100 to 240VAC, 50 / 60Hz

Power Consumption

Screen display ON

25W or less

Power saving mode

4W or less

Power button OFF

1W or less

Regulatory Safety Approval FCC & CE

Environmental Conditions

Operating

Temperature

0 to 50°C degree

Humidity

20~90%, non-condensing

Storage

Temperature

-5 to 60°C degree

Humidity

5~90%, non-condensing

Shock

10G acceleration (11ms duration)

Vibration

5~500Hz 1G RMS random

RMWQ 8190

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 9

RMWQ 8190

Physical Specification

Product ( W x D x H )

445 x 650 x 44 mm

17.5 x 25.6 x 1.73 inch

Packing ( W x D x H )

595 x 860 x 140 mm

23.4 x 33.9 x 5.5 inch

Net Weight

12.5 kgs / 28 lbs

Gross Weight

16.5 kgs / 36 lbs

Applicable Format

DVI-D / VGA Input

PC Signal

1440 x 900 x 60Hz

1280 x 1024 x 60 / 75Hz

1280 x 960 x 60Hz

1280 x 760 x 60 / 75Hz

1152 x 864 x 75Hz

1024 x 768 x 60 / 70 / 75Hz

848 x 480 x 60Hz

800 x 600 x 60 / 72 / 75Hz

720 x 400 x 70Hz

640 x 480 x 60 / 72 / 75Hz

640 x 400 x 70Hz

640 x 350 x 70Hz

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 10

< 2.2 > On-screen Display Operation ( OSD )

Power light Green = On Orange = Power saving

Membrane Switch Function

LCD OSD Menu

Power on / off LCD

Display the OSD menu

Scrolls through menu options and adjusts the displayed control (To auto adjustment by pressing the button for 5 seconds)

Exit the OSD screen

Toggle analog, digital & video connection (DVI-D and video options only)

OSD Configuration Page

Image:

for the bri ghtness, contrast, color temp, red, green, and blue

Geometry:

for the auto adjust, H position, V position, phase and clock

Video:

for the colour, tint, sharpness, noise reduction, DCDi and TV Setup

Audio:

for volume, bass, treble, balance, AVL and mute

Misc:

for the language, OSD position, graphic mode, ratio, reset and timer

Page 11

RMWQ 8190

< Part 3 >

< 3.1 > Options : DC Power

Model

12V

24V

48V

Input rating

Input voltage:

12-Volt

24-Volt

48-Volt

Input range:

9 ~ 18V

18 ~ 36V

36 ~ 75V

Input current

- No load

50 mA

- Full load

4950 mA

2450 mA

1220 mA

Output rating

Output voltage:

12-Volt

Output current:

4.16A

Efficiency

84%

85%

***

Option excludes 1 x power cord and 1 x AC power adapter

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 12

< Part 4 >

< 4.1 > QD Connection

1. VCR in :

This BNC connector is connected to video output from VCR/DVR. A pre-recorded quad screen signal from a tape can be played back through a VCR/DVR and displayed on the video output channels. Push the VCR button (#2) to switch the device to VCR Playback mode.

2. VCR out :

This BNC connector is to be connected to the Video in from your VCR/DVR. It will only provide a quad screen video to ensure an un-interrupted video recording for all four cameras. The display video is not affected by the control panel.

3. Terminations :

These impedance switches are used to provide proper termination for each camera input. These switches toggle between 75Ω and Hi-Z impedance. Incorrect termination will degrade the quality of the video signal. All video inputs not “looped through” to another device, the corresponding switches need to be set to 7 5Ω termination position. If another device is connected to video out loop through connector set the corresponding termination switch to Hi -Z position. Any device connected to the video out loop through connectors needs to be configure to 75Ω video termination. The factory default termination setting is 75Ω.

4. Ch1 In, Ch2 In, Ch3 In, and Ch4 In Video IN connectors : These BNC connectors are used to connect to the video out from camera. Four cameras can be connected to th ese connectors to form a quad screen in the following mapping orde r.

5. Ch1 Out, Ch2 Out, Ch3 Out, and Ch4 Out Video Loop through connectors : These connectors are used to loop video signals from each camera out to other devices.

Page 13

< 4.2 > QD ALARM Connection & Operation

1. ALARM I/O :

This female type 9 pin D-sub connector is used for alarm sensor input and alarm output contro l connections. It provides Normal Open and Normal Close contacts for alarm out control.

Pin Assignment for Alarm Connector (female type)

PIN#

Sensor 1

Sensor 4

Normal Open Contact

Sensor 2

Reset In

Common Contact

Sensor 3

GND

Normal Close Contact

The Alarm Hold Time can be configured from 0 second to 99 minutes through system Setup menu.

2. VCR Connection for Tape Recording Start and Stop Control :

Connecting the contacts of VCR RECORD and STOP switch to the alarm output NC and NO contacts will allow you to use an ordinary VCR to record for longer period of time. Combined with alarm sensor detection, the VCR will record only when an alarm sensor is activated.

*. If more than one sensor have been trigged, VCR will start to record after the last trigged event. *. In order to make use of the alarm called full screen display function, the VIDEO IN connector from the VCR has to be connected to LIVE monitor connector of the device. If more than one sensor are trigged, VCR will then record all the events in full screen mode accordingly.

Page 14

RMWQ 8190

A larm

< 4 .2 > Q D ALAR M Con nection & O peration

3 Sen sor A ctivat ed Alarm

The u n it is equippe d w ith 4 al a rm s ensor inputs. If any alarm is activ ated:

¦ the bu i lt -i n buzz er and the al arm output c o ntrol rel a y con ta c t will be activated. ¦ the qu ad w ill s wi tch th e co rrespo ndin g c han nel ind icator LED to blin ki ng m ode . ¦ a w a rn ing mess age d epen ding o n di ffer ent m o dels will be displ a ye d as follow s:

Qu ad ou tp u t c h an ne l (# 4 )

LIVE outpu t ch an ne l (# 5 )

Blin kin g A la r m & T itle m essa ge o n the activated c han ne l in qu a d scree n

A larm

F u ll s c r e en dis p lay of the a ctiva te d cha n ne l. A lso disp lay a bli nking A larm m essag e

Ab ove men tioned a larm can b e c leared b y an y of th e fol lowing: 1. Con nec ting the Al arm Re s e t In co ntac t, pin #5 , of the female ty pe 9 pin D -sub con necto r (#8) to G ND. 2. Th e Alarm D uration time el a pses . 3. If the d evic e is operated un der Se c u rity Lo ck ON m o de , Pu s h L o ck bu tton for 2 sec ond s to dis able the fun c tion the n p ush any button in the fron t pa nel.

4 V ideo Loss Alarm

L o ss of v ideo a t any input is au to m atically d etecte d by the d ev ice . T he device will:

¦ A ctiv ate the b uilt -in bu zze r. ¦ S wi tch th e co rresp ondin g chann el indic ato r LED to b li nking m ode. ¦ Display warnin g me ssage on qu ad s cr e en:

Qu ad ou tp u t c h an ne l (# 4)

Vi de o lo ss

B linkin g V id eo Lo s s & Title m es sa g e on the activa te d cha n ne l in qu ad screen

¦ The war n ing mes sage an d the b uzz e r c a n be clear e d

by pus hing Lo ck butto n (#2) fo r m ore than 4 sec ond s if the de vi ce is operate d unde r Secur ity loc k On mod e, o r p ushing an y bu tton o n the fron t pa nel if the d ev ic e is op erated un der Se curity lock OF F mode.

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 15

RMWQ 8190

< 4.3 > QD Remote Control Connection & Operation

Rear Panel

RS-2 32

h i- z

1 2 3 4

OUT

dc 1 2V, 1amp

ALARM I/O

monitor vcr

RS-232 Cab le W ire

Computer

Remote Keypad

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 16

RMWQ 8190

Pin Assignmen t for Remote Control Connector

GND4NC7VCC

2RX5NC8

GND

3TX6

VCC9GND

< 4.3 > QD Remote Control Connection & Operation

The device can be controlled via the male type 9 pin D-sub/RS-232 connector to a computer using ASCII code.

1. Pin assignment of the male type 9 pin D-sub connector:

1 2 3 4 5

6 7 8 9

When a computer is used to control this device through a RS-232 port, pin 6, 7, 8, and 9 must be disconnected to prevent connecting the VCC and GND signals from the device to the computer. A RS-232 port only uses pin 1, 2, and 3 for control signal transmission.

2. A terminal or computer can be connected to the male type 9 pin D-sub connector on the real panel from it RS232 port to control this device using standard, uppercase ASCII codes.

2.1 The ASCII command codes for the quad are listed in the table below. The transmission protocol is 1200baud rate, 8 data bit, 1 start bit, 1 stop bit, and no parity.

Function

ASCII Command Code

Quad Screen Display

CH 1

CH 2

CH 3

CH 4

Freeze *1

EA, EB, EC, ED

Auto Switching Sequence

VCR/Live

Key Lock *2

Setup Menu *3

Text Select Down *4

(GH) A

Text Select Up

(GH) B

Cursor Left

(GH) C

Cursor Right

(GH) D

Alarm Reset

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 17

RMWQ 8190

< 4.3 > QD Remote Control Connection & Operation

*1. In order to control the device to operate in Zoom mode, the computer has to first send

command code ” to switch the signal source from camera to VCR/DVR, at this time the device will automatically zoom channel 1 video from VCR/DVR to full screen. User can then input a corresponding channel code to zoom any other specific channel . Input the corresponding channel code again to put the specific channel to freez e mode and send the code again to clear the freeze mode.

Example: Input GE, (GE) B, (GE) C, and (GE) D for zooming the video signal in channel 1 to 4 from VCR/DVR. Input “A”, “B”, “C”, “D” again to freeze the specific channel. Send command code “G” again to get back to Live input mode.

*2. Computer has to send out command code “H” continuously for 2 seconds to switch the device be-

tween security lock ON and OFF mode. If any alarm is activated under security lock ON mode, the device has to send out command code “H” continuously for more than 4 seconds to clear the alarm.

*3. Setup menu is switched ON by sending VCR/DVR and Lock button codes together.

*4. Text Select and Cursor Control functions can be performed only under menu Setup mode.

2.2 Right after computer/terminal has sent out the above mentioned control command code to the device, the

device will respond with following status code back to computer through RS-232 port:

Status

Code

Quad Status

Status

Code

Quad Status

Device in Quad mode

CH1 in Sequence mode

CH1 in Freeze mode

CH2 in Sequence mode

CH2 in Freeze mode

CH3 in Sequence mode

CH1 & 2 in Freeze mode

CH4 in Sequence mode

CH3 in Freeze mode

Quad display in Sequence mode

CH1 & 3 in Freeze mode

CH2 & 3 in Freeze mode

CH1 in Full screen mode

CH1, 2, & 3 in Freeze mode

CH2 in Full screen mode

CH4 in Freeze mode

CH3 in Full screen mode

CH1 & 4 in Freeze mode

CH4 in Full screen mode

CH2 & 4 in Freeze mode

CH1, 2 & 4 in Freeze mode

Attach to above code

CH3 & 4 in Freeze mode

XX -DF

Buzzer/VCR ON

CH1, 3, & 4 in Freeze mode

XX-7F

Security lock ON

CH2, 3, & 4 in Freeze mode

XX-3F

Buzzer & Security lock ON (Stop)

CH1, 2,3, & 4 in Freeze mode

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 18

RMWQ 8190

}

< 4.3 > QD Remote Control Connection & Operation

2.3 The configuration of the status code for both normal and alarm operations: There are total 2 bytes of the status codes. Byte one, the first 8 bits, shows the current status of the operation modes that the unit is in. Byte two, the second 8 bits, shows the current status of the alarm operations of the unit.

BYTE 1 BYTE 2

START STOP START STOP

BYTE 1: Status code for normal operation modes

b7 b6 b5 b4 b3 b2 b1 b0

LOCK VCR SEQU QUAD CH4 CH3 CH2 CH1

Channel Select

1110 = CH1 1101 = CH2 1011 = CH3 0111 = CH4

Display Mode

0 = Quad screen display 1 = Full Screen display

Auto-sequencing mode

0 = Auto sequencing mode 1 = Quad or full screen mode

VCR mode

0 = VCR operation 1 = Live operation

Security Lock mode

0 = Security lock ON mode 1 = Security lock OFF mode

Menu Setup mode

00 = Menu setup mode

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 19

RMWQ 8190

< 4.3 > QD Remote Control Connecti on & Operation

BYTE 2: Status code for alarm operations: The first 4 bits show the sensor activated alarm status of each channel; next 4 bits show the video loss alarm status of each channel. The digit “1” means alarm event is detected, and “0” means no alarm event is detected.

b7 - b4: Sensor Activated Alarm b3 - b0: Video Loss Alarm

b7 b6 b5 b4 b3 b2 b1 b0

CH4 CH3 CH2 CH1 CH4 CH3 CH2 CH1

Sensor activated Alarm 0001 = CH1 activated 0010 = CH2 activated 0100 = CH3 activated 1000 = CH4 activated

Video Loss Alarm 0001 = CH1 activated 0010 = CH2 activated 0100 = CH3 activated 1000 = CH4 activated

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 20

< 4.4 > QD OSD Operation

Quad Display C o ntrol

Setup

VCR SEQ

< >

2 4 5

Lock: Security locks out button. Push this button for 2 seconds to enable control panel lock out function. Push this

button again for 2 seconds to disable the function.

2 V CR: Push this button to enter into VCR Playback/Zoom operation. In this mode, the output video i s displaying the

video signal from VCR. When operated in Full Screen display mode, push select buttons (#5) to zoom any spec ific camera signal pre-recorded on the tape in quad format. Push the select button (#5) again to freeze the expanded picture on the screen.

VCR

button (#2)

Quad

button (#4)

CH Select

button (#5)

Function

ONONOFF

Display quad video signal from VCR tape

OFF

Push Once

Call up specific quadrant from tape in full screen mode

OFF

Push Twice

Freeze specific quadrant from tape in full screen mode

OFFXX

Exit VCR operation and back to normal operation mode

#1, #2 Setup buttons: Push these two buttons simultaneously to get into Menu Setup mode and display page 1 of system setup menu. Push these two buttons simultaneously again to display page 2 of the setup menu. Use page 1 to program time/date and camera title and page 2 to configure alarm operations. Under menu setup mode, Channel Select buttons (#5) are used for cursor control and text selection to program the setup menu. Push the setup buttons simultaneously again to save the setting. Push the setup buttons fourth time to get back to ordinary operation mode.

Setup buttons (#1, #2)

Function

CH Select buttons (#5)

UP, DOWN

< , >

Push once

Page 1 menu for time / date / title programming

Text Selection

Cursor Control

Push twice

Page 2 menu for alarm configuration

Text Selection

Cursor Control

Push the third time

Save the settings

Yes / No

Push the fourth time

Exit setup mode, back to normal

SEQ.: Push this button to enable full page auto sequencing mode. Push this button again to disable it.

4 : Push this button to switch between Quad/ Full Screen display mode.

5 buttons: When operated in Quad mode, these buttons are used to freeze any specific camera

by pushing the corresponding button. When operated in Full Screen display mode, these buttons are used to select specific camera to be displayed in full screen.

Quad button (#4)

Channel Select buttons (#5)

Function

Freeze specific camera video in Quad screen mode

OFF

Call up specific camera video in full screen mode

These buttons are also used as cursor control and text select keys under Setup menu mode.

Page 21

< 4.5 > QD On-screen Menu

Right after the unit is turned on, The monitor will display the last setting on the Setup Menu.

1. Page 1 of the Setup Menu - Display Setting

Push Setup buttons (#1, #2) simultaneously to display the Setup Menu on the screen. There are total two pages in the Setup Menu. Page 1 is used to program TIME, DATE, and camera TITLE. Page 2 is used to program Alarm Operations. Under this mode, channel selection buttons (#5) on the front panel are used for cursor control and text selection. Use the cursor control buttons "<" and ">" to move the cursor to the location as desired to program, and use the text select but tons " " and " " to choose the right alphanumeric character to program.

Page 1: Setting the TIME, DATE, TITLE, and DWELL time:

CH TITLE

QUAD

DWELL TIME

03S 1 CH 1 03 S 2 CH 2 03 S 3 CH 3 03 S 4 CH 4 03 S LIVE VIDEO FREEZE ON

VIDEO OUT:

LIVE

QUAD

TITLE:ONON

TIME: 23 : 10 : 10

DATE: 12 - 25 - 2003

1.1 TITLE setup:

The Title menu permits the setup of separate titles for each video channel. 8 characters may be e ntered for each video channel. The available alphanumeric characters are:

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D,..... X, Y, Z, . , :, - , / , < , > , , , space ,

1.2 DWELL Time setup:

The Dwell time menu permits setting the dwell time for all ca meras and the Quad Screen on the LIVE output channel. The menu shows a table of all cameras and associated dwell time. Dwell time can be programmed by setting a number between 00 to 99 for each channel in the menu.

¦ 01 through 99: Adds the camera input to the auto switching SEQUENCE, with the corresponding dwell time in

seconds.

¦ 00: Skips the camera input in the auto switching SEQUENCE.

1.3 TIME/DATE setup:

Time and date informati on can be displayed on the video output channel through both LIVE and QUAD connector. Bottom of page 1 is used to set the values of time and date and also to enable or disable the display at each output channel.

The date and time will display in the “MM-DD-YYYY HH:MM:SS” format for NTSC model and “DD-MM-YYYY HH:MM:SS” format for PAL model.

1.4 TITLE/TIME/DATE disable and enable on LIVE and QUAD video output channel:

The Title/Time/Date display on each output channel can be enabled or disabled by setting ON or OFF in the correspond ing entry.

Page 22

< 4.5 > QD On-screen Menu

2 Page 2 of the setup menu- Alarm Setting

Push Setup buttons (#1, #2) simultaneously and push (#1) button again to display page 2 of the setup menu on the screen. This Alarm Setting menu is used to set the desired alarm configuration like sensor type, sensor sensitivit y, alarm hold duration, and buzzer.

ALARM SETTING

SENSOR

TYPE

STATUS

OPEN

SENSITIVITY: 0.3 S DURATION: 30 S BUZZER: ON V-LOSS ALARM: ON V-LOSS RELAY: OFF

2.1 Sensor Type:

The machine will first detect the type of the sensor connected to the corresponding channel. The result will be displayed in the first column following each channel number. They can be on either OPEN or CLOSE. The menu then allows user to enter a desired type of the sensor for each channel in next column. NO means Normally Open. NC means Normally Close.

Then the menu will allow user to enable or disable sensor input for each channel in the next column. ON will enable the contact to detect the alarm status from the input. OFF will ignore the sensor input and disable the alarm detection from the input. Last column on this part of the menu shows the result of the actually detected sensor type and the desired configur ation. If the setup type of the sensor is different from the actually connected type of senso r, a blinking “?” message will display. In this case, the buzzer will be activated when you exit the setup operation.

2.2 Alarm Sensitivity:

Alarm sensitivity can be programmed to different extent by setting the period of the trigged pulse detected b y the senso r. The available settings are 100ms, 200ms, 300ms, 400ms, 500ms, 600ms, 700ms, and 800ms.

2.3 Alarm Hold Duration:

The alarm hold duration can be set from 0 0 second to 59 minutes. The duration can be set to non-stop by choosing “>>“. In this mode, the activated alarm can only be reset by connecting the alarm reset contact to ground.

2.4 Buzzer:

The device has a build -in buzzer to signal a detected alarm thro ugh sound. User can choose to disable the buzzer by setting it to OFF.

2.5 V-Loss Alarm:

This entry is used to enable or disable the video loss alarm. The device automatically detects loss of video at any input if this entry is set to ON. User c an choose to disable this feature by setting it to OFF for applications like video conferenc ing or others that will need constant video source switching.

2.6 V-Loss Relay Control:

The device is equipped with an alarm controlled rela y, which can be activated by both sensor trigged alarm and video loss alarm. This entry allows user to disable the relay activation from a loss of video in any camera input.

3 Save the settings and exit Setup Menu mode

Push (#1) button again will allow you to save the settings and go back to the normal operation mode and show a quad display on the screen.

Page 23

RMWQ 8190

< 4.5 > QD On-screen Menu

4: The setup menu can be reset to factory setting by pushing the Setup buttons (#1, #2) and power on the quad simultaneously. The factory setting is as follows:

CH TITLE DWELL TIME AL ARM S ET TING

QUAD

03S

SENS OR

TYPE

STAT US

CH 1

03 S

OPE N

CH 2

03 S

OPE N

CH 3

03 S

OPE N

CH 4

03 S

OPE N

LIVE V IDE O FREEZE ON

VIDEO OU T: LIVE QUAD

TITLE: ON ON

TIME: 23 : 10 : 10 ON ON

DAT E: 1 2 - 25 - 200 3 ON ON

SENSI TIV ITY: 0.3 S

DUR ATION : 30 S

BUZZE R: ON

V-LOSS ALAR M: ON

V-LOSS R ELAY: OFF

5. The Quad Display Mode

5.1 Push Quad display button (#4) to switch between Quad screen and Full scree n display mode. Right after you turn on the system, the unit is in the quad mode and displays cameras 1-4.

5.2 Use page 1 of the Setup menu to turn the Title display ON/OFF on each channel and also enable and disable

the Time and Date display on LIVE and QUAD output channels.

5.3 Under Quad screen mode, pus h channel select button to freeze each camera input.

6. The Full Screen Display Mode

6.1 Push Quad button (#4) to OFF to enter Full screen display mode. Under this mode, you may call up any spe

cific channel in full screen by simply pushing the corresponding channel selection button.

6.2 Push the Quad button (#4) to ON to retu rn to the quad mode.

7. The Still Frame Display Mode

7.1 If the still screen mode is desired, first turn the quad display button (#4) to ON to set the unit to display in the

quad mode. At this time you may press any of the four channel selection buttons (#5) to freeze the correspondi ng channel.

7.2 Under Zoom On VCR playback mode, if the unit is showing quad screen, pushing the channel selection but tons (#5) will call up the specific channel to display in full screen. Push the same channel selection button again to freeze that channel in full screen.

8. The Auto-Sequence Mode

Push the Sequence button (#3) to ON to set the device to work as a sequencer. Under this mode, the display sequence first starts with a quad screen and then continues to display each camera input in full screen, and then gets back to quad screen and so on. Press the Sequence button (#3) to OFF to release this mode.

8U 19” 1440x900 Rackmount CCTV Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 24

< 4.6 > QD VCR Operation

Zoom on VCR playback operation: Push VCR button (#2) to ON will switch the device to VCR pl ayback mode. Under this mode, if the device is on quad display mode, a pr-recorded quad display video in the tape will be shown on the screen. If the device is in Full screen display mode, push any channel select buttons (#5) will select and expand the corresponding quadrants of the pre recorded video to full screen display.

< 4.7 > Quad Display Specification

Item

Description

Model Number

QD (NTSC) QD (PAL)

Number of Color

16.7 M

Imaging System

NTSC

PAL

Resolution

1024 x 525

1024 x 625

Refresh Rate

Video In put Camera Input

1.0 Vpp, 75 Ohm x 4

VCR Inpu t

1.0 Vpp, 75 Ohm x 1

Video Output

Live Monitor

1.0 Vpp, 75 Ohm x 1

Loop Through Out

1.0 Vpp, 75 Ohm x 4

VCR Output

1.0 Vpp, 75 Ohm x 1

Auto Gain Control

Yes

Time / Date

Yes

On Screen Display

Yes

Camera Title

8 Character Title

Display Format

2 x Zoom On Playback

Yes

QUAD

Yes

FULL

Yes

SEQUENCY

Yes

Dwell Time

0 to 99 Sec Adjustable

Alarm Inputs

Selectable NO/NC Contacts x 4

Relay Outputs

NO/NC contacts x 1: 1A @DC24V Max.

Alarm Hold Time

1 Sec to Non-stop

Built-in Buzzer

Yes

Key Lock

Yes