Acnodes RM 6821 User Manual

Download

Page 1

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

User Manual

RM6821: 8U 21.5” 1920x1080 650-nit High Brightness Industrial Rackmount Monitor

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All righ ts reserved. Product descripti on and product speci ficat ions are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 2

RM 6821

Legal Information

First English printing, October 2002 Information in this document has been carefully checked for accuracy; howeve r, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.

Safety Instructions

Please read all of these instructions carefully before you use the dev ice. Save this manual for future reference.

¦ Unplug equipment before cleaning. Don’t us e liquid or spray detergent; use a moist cloth.

¦ Keep equipment away from excessive humidity and heat. Pre ferably, keep it in an air-conditioned environment with

temperatures not exceeding 40º Celsius (104º Fahrenheit).

¦ When installing, place the equipment on a sturd y, level surface to prevent it from accidentally falling and causing

damage to other equipment or injury to persons nearb y.

¦ When the equipment is in an open position, do not cove r, block or in any way obstruct the gap between it and the

po wer supply. Proper air convection is necessary to keep it from overheating.

¦ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.

¦ If you are using a power co rd that didn’t ship with the equipment, ensure that it is rated for the voltage and current

labeled on the equipment’s electrical ratings label. The voltage rating on th e cord should be higher than the one listed

on the equipment’s ratings label.

¦ Obs erve all pre cautions and warnings attached to the equipment.

¦ If you don’t intend on using the equipment f or a long time, disconnect it from the power outlet to prevent being

damaged by transient over -voltage.

¦ Keep all liquids away from the e quipment to minimize the risk of accidental spillage. Liquid spilled on to the power

supply or on other hardware may cause damage, fire or electrical shock.

¦ Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and

invalidate its warranty.

¦ If any part of the equipment bec omes damaged or stops functioning, have it checked by qualified service personnel.

What the warranty does not cover

¦ Any product, on which the serial number has been defaced, modified or removed.

¦ Damage, deterioration or malfunction resulting from:

? Accident, misuse, neglect, fire, water, lightn ing, or other acts of nature, unauthorized product modification, or

failure to follow instructions supplied with the product.

? Repair or attempted repair by an yone not authorized by us.

? Any damage of the product due to shipment.

? Removal or installation of the pr oduc t.

? Causes external to the product, such as electric power fluctuation or failure.

? Use of supplies or pa rts not meeting our specifications.

? Normal wear and tea r.

? Any other causes which does not relate to a product defect.

¦ Removal, installation, and set-up service charges.

Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tes ted and found to comply with the limits f or a Class B digital device, pursuant t o Part 15 of the F CC rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment g enerates, uses, and can radiate radio frequency energy and, if not instal led and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no g uarantee that int erference will not occ ur in a particular installation. If this equipment does cause ha rmful interference to radio or television reception, which can be determined by turning the equipment o ff and on, t he user is encouraged to try t o correct t he interference by one or more of the following measures:

¦ Re-position or relocate the receiving antenna.

¦ Incre ase the separation between t he equipment and receiver.

¦ Connect the equipment into an outlet on a c ircuit di fferent from that to w hich the receiver is connected.

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 3

Contents

< Part. 1 > RM 6821

1.1 Package Content

1.2 Structure Diagram & Dimension

1.3 Installation

P.1 P.1 - 2 P.3

< Part. 2 > Specifications / OSD / Remote Controller

2.1 Product Specifications

2.2 On-screen Display Operation ( OSD )

2.3 Picture In Picture ( PIP ) / Picture By Picture ( PBP )

P.4 - 5 P.6 - 7

P.8 - 9

< Part. 3 > Options

3.1 3G / HD / SD-SDI Broadcast-grade input

3.2 MCS Multi-display control solution

3.3 AV3.0 Upgrade : DVI-D + VGA + HDMI + BNC + S-Video + Audio

3.4 HF21" Touchscreen : Resistive, Capacitive, Multi-touch

3.5 48V, 24V or 12VDC power

3.6 MIL-type or lockable connector

P.10 P.11 P.12

P.13 P.14 P.15

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 4

RM 6821

Before Installation

¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface. ¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive

dust, dirt, heat, water, moisture and vibration.

Unpacking

The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good c ondition. If anything is missing, or damaged, contact the supplier immediatel y.

How To Clean Your LCD Monitor

Caution :

¦ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or

plugging your monitor into an electrical outlet.

¦ When you clean your monito r, do not press down on the LCD screen. Pr essing down on the screen can

scratch or damage your display. Pressure damage is not covered under warrant y.

¦ Use only cleansers m ade specifically for cleaning monitors and monitor screens. Cleansers not made to

clean monitors and monitor screens can scratch the LCD display or strip o ff the finish.

¦ Do not spray any kind of liquid directly onto the screen or case of your monito r. Spraying liquids directly

onto the screen or case can cause damage which is not covered under warrant y.

¦ Do not use paper towels or abrasive pads to clean your monito r. Using an abrasive pad or any wood based

paper product such as paper towels can scratch your LCD screen.

Cleaning Your Monitor

To clean your LCD safely, please follow these steps :

Disconnect the power cord.

Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.

Cleaning Tough Marks and Smudges

To remove tough marks and smudges, please follow these steps :

Disconnect the power cord.

Spray a small amount of non-abrasive cleanser on a microfi ber cloth.

Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your microfiber cloth first, not directly on the parts you are cleaning.

Gently wipe the surface. Use as little pressure as possible.

Wait until your monitor is completely dry before plugging it in and powering it up.

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 5

< P a rt 1 >

< 1 .1 > P ac k a g e C o nten t

R M 6 8 2 1 un it X 1

- 6 f t VG A c ab le X 1

- Po w e r a d ap t e r X 1

- Po w e r c ord X 1

- Fa ste n e r s c r ew fo r r e a r b r ac k e t x 2

< 1 .2 > S tru c ture D iag ra m

F ro n t v iew

P ow e r a d ap te r

R ea r vi e w

L CD p a n el

2 L C D m em br a ne

Lat c h t o re le a s e th e d isp l a y pa n e l fro m the rea r b r ac ket

R e a r m ountin g bra c ke t

5 P owe r ad apte r bask e t

Po we r c o r d

DV I -D

A ud io

P ow e r B NC S -V ide o V G A H DM I

S tan dar d

AV3. 0 up grade

O ptio n

ou t - i n - in

V ide o PC

: D V I - D + V G A + H DM I w / sp e a k er

: D V I - D + V G A + H DM I + B N C + S -V id e o + a ud io

: S D I, U S B fo r t ou ch s c ree n & D C po w e r

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 6

RM 6821

< 1.2 > Dimension

Front View Side View

Bottom View

UNIT : mm

1mm = 0.03937 inch

Model

Product Dimension

(W x D x H)

Packing Dimension

(W x D x H)

Net

Weight

Gross

Weight

RM 6821

501.9 x 64 x 353 m m

19.8 x 2.5 x 13.9"

555 x 124 x 537 mm

21.9 x 4.9 x 21.1"

10 kg

22 lb

13 kg

28.6 lb

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 7

< 1.3 > Installation

Step

¦ Mount the rear bracket with M6 screw set. ¦ 8 x M6 screw set are required.

M6 screw sets are not provided.

rear bracket

Step

¦ Insert the upper part of the RM 6821

display panel into the rear bracket.

Step

¦ Push the lower part of the RM 6821

display panel into the rear bracket.

Fastener screw

Step

¦ Fix the RM 6821 display panel into the rear

bracket with two fasteners ( Left & right side ).

¦ Lock the RM 6821 display panel by the

latch ( on the bottom left & right side ).

latch

Page 8

< Part 2 >

< 2.1 > Product Specifications

LCD Panel

Panel Size ( diagonal )

21.5-inch Widescreen TFT color LCD

Display pixel ( dots x lines )

1920 x 1080

Brightness ( typ. )

650

Contrast Ratio ( typ. )

5000:1

Color

16.7 M

Viewing Angle ( L/R/U/D )

89/89/89/89

Response Time ( ms )

Dot pitch ( mm )

0.248

Display Area ( mm )

476.64H x 268.11V

Surface treatment

Anti-glare

Surface hardness

Backlight Type

LED

MTBF ( hrs )

50,000

Video Connectivity

Digital

HDMI

HDMI 1.1, CEA-861-D

DVI

DVI-D, TMDS single link

Analog

VGA

Analog 0.7Vp-p

Composite ( RCA )

NTSC & PAL

S-Video ( 4-pin )

NTSC & PAL

Plug & Play

DVI / VGA

VE SA EDID structure 1.3

Synchronization

VGA

Separate, Composite & SOG

Audio Connectivity

Audio Input

Connector

3.5mm stereo jack

Impedance / Power level

30kΩ / 750mV

Audio Output

Connector

3.5mm stereo jack

Resistance / Power level

30kΩ / 2.8V

Speaker Output

Power

2 x 2W

*When the audio output is connected, speaker output is OFF

Power

Power Supply

Range

Auto-sensing 100 to 240VAC, 50 / 60Hz

Power Consumption

Screen display ON

65W or less

Power saving mode

6W or less

Power button OFF

2W or less

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 9

Regulatory Safety Approval FCC & CE

Environmental Conditions

Operating

Temperature

0 to 50°C degree

Humidity

20~90%, non-condensing

Storage

Temperature

-5 to 60°C degree

Humidity

5~90%, non-condensing

Shock

10G acceleration (11ms duration)

Vibration

5~500Hz 1G RMS random

Physical Specification

Product ( W x D x H )

501.9 x 64 x 353 mm

19.8 x 2.5 x 13.9 inch

Packing ( W x D x H )

555 x 124 x 537 mm

21.9 x 4.9 x 21.1 inch

Net Weight

10 kgs / 22 lbs

Gross Weight

13 kgs / 28.6 lbs

Applicable Format

DVI-D / VGA Input

PC Signal

1920 x 1080 x 60Hz

1280 x 1024 x 60 / 75Hz

1280 x 960 x 60Hz

1280 x 768 x 60 / 75Hz

1152 x 864 x 75Hz

1024 x 768 x 60 / 70 / 75Hz

848 x 480 x 60Hz

800 x 600 x 60 / 72 / 75Hz

720 x 400 x 70Hz

640 x 480 x 60 / 72 / 75Hz

640 x 400 x 70Hz

640 x 350 x 70Hz

HDMI Input

PC Signal

Same as VGA

Video Signal

1080p : 50 / 60Hz

1080i : 50 / 60Hz

720p : 50 / 60Hz

480p : 60Hz

576p : 50Hz

Audio Signal

2ch Linear PCM ( 32 / 44.1 / 48 KHz )

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 10

< 2.2 > On-screen Display Operation ( OSD )

Membrane Switch Functi on

Turn the monitor on or off

Display the OS D menu

Act as an Enter key to select screen setting options

Scroll through menu options and adjust

the displayed control

Exit the OSD screen Go back to the previous on-screen sub-menu or main menu

Remark : All LED touch buttons in WHITE light.

The LED of Power touch button will flash continuously when there is no signal input.

1 All the LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power ).

2 Light up all membrane buttons, please press any button for 1 - 2 seconds ( except the Power ).

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 11

< 2.2 > On-screen Display Operation ( OSD )

Picture

Picture mode : Standard / Vivid / Soft / User mode to choose Brightness :

Adjust background black level of the screen image

Contrast : Adjust the difference between the image background

(black level) and the foreground (white level)

Hue: Adjust the screen hue value

Saturation : Adjust the saturation of the image color

Picture size : Adjust the image size

Color temp : Standard / Cool / Warm / User to choose

Noise reduce : Reduce the noise of the image Sharpness :

Adjust the image from weak to sharp

Auto adjust : Automatically adjust sizes, centers and fine tunes the

video signal to eliminate waviness and distortion.

Clock : Adjust the clock value

Phase : Adjust the phase value

H. Position : Align the screen image left or right

V. Position : Align the screen image up or dow n

Audio

Audio mode : Mo vie / Voice / Normal / Music mode to choose

Volume : Adjust the volume of sound

Bass : Set the value of bass sound

Treble : Set the value of treble sound

Balance : S et the balance value of treble and bass sound

Analog TV audio : Set the value of analog TV audio sound

Mute : Turn off the surrounding sound

MISC

Language : Select the language in which the OS D menu is

displayed - English

Sleep timer : Set the off time

PIP mode : Adjust picture in picture setting

PIP position : Enter into PIP position

PIP source : Enter into the Sub source and sound source

System reset : Return the adjustment back to factory setting

Information : Select for Help

Page 12

RM 6821

< 2.3 > How to Use Picture In Picture ( PIP ) / Picture By Picture ( PBP )

< 2.3.1 > Picture in Picture ( PIP )

Mode

Display the Sub screen in the Main screen.

OSD Menu ? MISC ? PIP Mode ? Large / Small / OFF

Main screen

Sub screen

Position

Adjust the position of the Sub screen ( top left, bottom left, top right, bottom right )

OSD Menu ? MISC ? PIP Position ? top left / top right / bottom left / bottom right

top left top right

bottom left bottom right

Size

Adjust the size of the Sub screen ( Large / Small )

OSD Menu ? MISC ? PIP Mode ? Large / Small

Size of Sub screen

LCD Monitor

Large Sub screen

Small Sub screen

1920 x 1200

552 x 414

480 x 360

1920 x 1080

552 x 414

480 x 360

1440 x 900

414 x 310

360 x 270

1366 x 768

392 x 294

340 x 254

1280 x 1024

368 x 276

320 x 240

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 13

< 2.3.2 > Picture By Picture ( PBP )

Mode

Display the Sub screen next to the Main screen.

OSD Menu ? MI SC ? PIP Mode ? PBP

Main screen Sub screen

Size

LCD Monitor

Main / Sub screen

1920 x 1200

955 x 716

1920 x 1080

955 x 716

1440 x 900

715 x 536

1366 x 768

678 x 508

1280 x 1024

635 x 476

< 2.3.3 > PIP / PBP Source

To select an input signal for PIP / PBP Sub screen.

OSD Menu ? MISC ? PIP Source ? VGA / S-Video / Composite / DVI / HDMI / SDI / YPbPr / TV

The PIP / PBP is operable in the following table :

Sub

Main

VGA

S-Video

Composite

DVI-D

HDMI

SDI

YPbPr

VGA

xoooooo

S-Video

oxxoooo

Composite

oxxoooo

DVI

oooxxoo

HDMI

oooxxoo

SDI

oooooxx

YPbPr

oooooxx

oxxoooo

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 14

< Part 3 >

< 3.1 > Optio ns : 3G / HD / SD -SDI input

Acn od es ’ SD I in pu t is an idea l solutio n for th e bro ad cast grad e vide o a n d hig h re solutio n CC T V m arket.

Desig ne d fo r u se wit h F ul l H D 10 8 0 p a n d ultr a h igh reso lutio n 192 0 x 12 0 0 LC D dis plays , Ac n od e s provi de s a SD I inpu t modul e w it ho u t usi n g a d ditiona l sp ac e or powe r an d it com e s st an dar d wit h a 2- yea r wa rran t y.

DVI - D

Audio

out - in - in

Vide o PC

Po wer BNC S-Video VGA

SDI

ou t - in

HDMI

*** F or S DI op tion, the A D board w i ll b e upg raded to AV3. 0, a nd t his co m es standa rd with HD M I, DVI -D,

VG A , S -V ideo , BN C and audio inp ut s.

INPU T

3G - SD I I N

BNC x 1 / 0 .8 V p -p ( 75 o h m )

3G - SD I O UT

BNC x 1 / Active t hrough, eq u alized & r eloc ked

Sta nda rd C om plian c e

Video

SMPT E 4 25 M / 2 74 M / 296M / 1 25 M ITU -R B T.656

Audio

SMPT E 2 99 M / 2 72 M -C

Com pa tibl e Vide o F orma t

3G - SD I

1080p @6 0 / 50 Hz, 4: 2 :2 1080p @3 0 / 25 / 2 4 H z, 4 :4 :4 1080i @60 / 5 0Hz, 4: 4:4 720p @ 6 0 / 5 0 Hz , 4: 4 :4

HD -SD I

1080p @3 0 / 25 / 2 4 H z, 4 :2 :2 1080i @60 / 5 0Hz, 4: 2:2 720p @ 6 0 / 5 0 Hz , 4: 2 :2

SD -SD I

480i @60Hz, 4:2 : 2

IT U -R B T.656

576i @50Hz, 4:2 : 2

Com pa tibl e A udi o F orma t

3G - SD I

48kHz, 16 / 20 / 24 bi t, 2 CH, Synch roniz ed Video

HD -SD I

48kHz, 16 / 20 / 24 bi t, 2 CH, Synch roniz ed Video

SD -SD I

48kHz, 16 / 20 / 24 bi t, 2 CH, Synch roniz ed / As ynchron ized V ideo

Max. Transm issi on Dista nce 75 ohm c oax ia l c ab le

3G - SD I

150m at 2 .9 7G b/s

HD -SD I

250m at 1 .4 85 G b /s

SD -SD I

480m at 2 70 M b /s

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 15

< 3.2 > Options : MCS ( Multi-display Control )

More control is always good. Especially when it is necessary and easy. Acnodes provides MCS solution to control the OSD of various LCD display up to 64 units.

The RS-232C is used for the communication between the PC and the first display via a 15 feet serial cable while the CAN bus is used for the various LCD displays cascade together via CAT 5/6 cable, and daisy chain up to 1,000 meters.

Designed for use with various LCD displays, Acnodes provides a MCS input module without using additional space or power and it comes standard with a 2-year warranty.

HDMI

Audio

Power BNC S-Video

out - in - in

Video PC

MCS

VGA DVI-D

set out in Link

*** For MCS option, casing depth will be changed.

RS-232C

Set switch

For the 1st and last display,

push the set switch upward

15 feet serial cable

( over 15 feet, extender required )

For other daisy chain displays,

push the set switch downward

LINK OUT IN OUT IN OUT IN OUT

Cat5 / 6 cable

max. 300 meters

Cat5 / 6 cable

max. 300 meters

Cat5 / 6 cable

max. 300 meters

RJ-45 jack

Daisy chain up to 1,000 meters and 64 displays

up to 64 displays

Page 16

< 3.3 > AV3.0 Upgrade Options :

- AV

- Audio

( S-Video + Composite, BNC )

( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )

DVI-D

Audio

out - in - in

Video PC

Power BNC S-Video VGA HDMI

< 3.4 > Options : Touchscreen & driver

21.5" USB Touchscreen Specification

Mod el

Technology

Touch Point

Method

Activation Force

Durability

Response Time

Optical Transmittance

Surface Hardness

Haze

Glass

Connector

Compatibility

TRB e-Resistive

TCB e-Capacitive

TMC2 Multi-touch

5-Wire Resistive

Capacitive

Projected Capacitive

Single

Dual

Stylus or Finger

Finger

= 50g / Stylus=R0.8

= 50g

10 million touches

300 million touches

100 million touches

15 ms

20 ms

80% ± 3%

87% ±2%

90% ±2%

3H9H7H

8% ± 3%

3.2 ±0.2 mm

2.8 mm ±10%

2.4 ±0.15 mm

USB Type A

Windows 7 / XP / Vista, Linux

Windows 7

¦ USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc ¦ For detailed information, please refer to the attached CD disc ¦ As the touchscreen unit is not made of toughened glass, please handle it carefully

USB Touchscreen

DVI-D Power VGA HDMI

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 17

DVI-D Power VGA

Please follow the below steps to setup the touch screen: -

Step 1. Run the bundled CD disc

Step 2. Double click the Setup.exe

Step 3. Follow the installation instruction to finish the setup

Step 4. After installation, run the TouchKit program & the “4 point calibration”

Please do the initial calibration after the first setup

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

Page 18

< 3.4 > Options : Touchscreen & driver

TMC2 Driver

Connect the USB cable from the USB port on the LCD to a compute r. The touch screen supports easy Plug-and-Play operations. There is no need to install additional drivers on the compute r.

< 3.5 > Options : DC Power

Model

24V

48V

Input rating

Input voltage:

24-Volt

48-Volt

Input range:

18 ~ 36V

36 ~ 75V

Input current

- No load

50 mA

- Full load

4880 mA

2442 mA

Output rating

Output voltage:

12-Volt

Output current:

8.3A

Efficiency

85%

86%

RM 6821

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939

© Copyright 2013 Acnodes, Inc. All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns are subj ect to change w ith out n oti ce. F or lates t product inform ati on, ple ase vis it Acnod es’ we b site at www.ac nodes.c om.

Page 19

RM 6821

< 3.6 > Options : MIL-type or Lockable Connector

Input

Part no.

MIL Standard

MIL - type Connector

DC Power *** ( Male )

MS3470W8 -33P

MIL - DTL - 26482

VGA *** ( Male )

MS3470W14-15P

MIL - DTL - 26482

*** There are several additional MIL DC and VGA connector types with varying design

characteristics to meet cost considerations and to provide users with the m ost design flexibility possible. For more information, please contact us.

Input

Part no.

Standard

Lockable Connector

DC Power ( Male )

YM-Ext-461CP001

D-type 3W3

USB

LUSB - A111 - 00

*** MIL - type or Lockable connectors above can be integrated with our LCD displays.

Sale service just for connectors not provided.

21.5” 1920x1080 650-nit High Brightness LCD 8U Rackmount Display Panel

14628 Ce ntral Ave, Chino , CA 91710 tel:909.597.7 588, fax:909.597.1939