Page 1
User Manual
RM6173/6193: 7/8U 17/19” 1000-nit High Brightness
Industrial Rackmount LCD Monitor
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 2
RM6173/6193
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; howeve r, no guarantee is given to the correctness of the contents. The inform ation in this
document is subject to change without notice. We are not liable for any injury or loss t hat results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the dev ice. Save this manual for future reference.
¦ Unplug equipment before cleaning. Don’t us e liquid or spray detergent; use a moist cloth.
¦ Keep equipment away from excessive humidity and heat. Pre ferably, keep it in an air-c onditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
¦ When installing, place the equipment on a sturd y, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearb y.
¦ When the equipment is in an open position, do not cove r, block or in any way obstruct the gap between it and the
po wer supply. Proper air convection is necessary to keep it from overheating.
¦ Arrange the equipment’s power cord in suc h a way that others won’t trip or fall over it.
¦ If you are using a power co rd th at didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. T he voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
¦ Observ e all precautions and warnings attached to the equipment.
¦ If you don’t intend on us ing the e quipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over -voltage.
¦ Keep all liquids away from the e quipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
¦ Only qualified servic e personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
¦ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
¦ Any product, on which the serial number has been defaced, modified or removed.
¦ Damage, deterioration or malfunction resulting from:
? Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
? Repair or attempted repair by anyone not authorized by us.
? Any damage of the product due to shipment.
? Rem oval or inst allation of the product.
? Causes ex ternal to the product, such as electric power fluctuation or failure.
? Us e of s upplies or parts not meeting our specifications.
? Norm al wear and tea r.
? Any other causes which does not relate to a product defect.
¦ Removal, installation, and set -up serv ice charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply w ith the lim its for a Class B digital device, pursuant t o Part 15 of the F CC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment g enerates, us es, and can radiate
radio frequency energy and, if not instal led and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee t hat int erference will not occur in a partic ular inst allation. If this equipment does cause ha rmful interference to radio or
television reception, which can be determined by turning the equipment o ff and on, t he user is encouraged to try to correct t he interference by one or more of
the following measures:
¦ Re-position or relocate t he receiv ing antenna.
¦ Increase the s eparation bet ween the equipment and receive r.
¦ Connect the equipment into an o utlet on a circuit di fferent from that to which the receiv er is connec ted.
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 3
Contents
< Part. 1 > RM6173/ 6193
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Installation
P.1
P.1 - 3
P.4
< Part. 2 > Specifications / OSD / Remote Controller
2.1 Product Specifications
2.2 On-screen Display Operation ( OSD )
P.5 - 6
P.7 - 8
< Part. 3 > Options
3.1 3G / HD / SD-SDI Broadcast-grade input ( except RM6173 )
3.2 MCS Multi-display control solution
3.3 AV2.2D Upgrade : DVI-D + VGA + BNC + S-Video + Audio
3.4 AV2.2H Upgrade : HDMI + VGA + BNC + S-Video + Audio
3.5 H17” / H19” Touchscreen : Resistive, Capacitive
3.6 48V, 24V or 12VDC power
3.7 MIL-type or lockable connector
P.9
P.10
P.11
P.11
P.12
P.13
P.14
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 4
RM6173/6193
Before Installation
¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anyt hing is missing, or damaged, contact the supplier immediat el y.
How To Clean Your LCD Monitor
Caution :
¦ To avoid the r isk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
¦ When you clean your monito r, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warrant y.
¦ Use only cleansers m ade specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip o ff the finish.
¦ Do not spray any kind of liquid directly onto the screen or case of your monito r. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warrant y.
¦ Do not use paper towels or abrasive pads to clean your monito r. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non -abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 5
< Part 1 >
< 1.1 > Package Content
RM6173 or RM6193 X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
< 1.2 > Structure Diagram
Front view
1
RM6173 RM6193
2
3
Rear view
Power adap ter
1
LCD panel
4
2
LCD membrane
3 Audio speaker
4
Power adapter basket
Pow er cord
DVI-D
Audio
Power BNC S-Video VGA HDMI
Standard
AV 2.2D upgrade
AV 2.2H upgrade
Option
out - in - in
Video PC
: DVI-D + VGA
: DVI-D + VGA + BNC + S-Video + audio
: HDMI + VGA + BNC + S-Video + audio
: SDI, USB for touchscreen & DC power
Page 6
RM6173/6193
< 1.2 > Dimension - RM6173
Front View Side View
Bottom View
RP-H717
UNIT : mm
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
RM6173
480 x 54.2 x 310 mm
18.9 x 2.1 x 12.2 inch
529 x 124 x 495 mm
20.8 x 4.9 x 19.5 inch
6 kg
13 lbs
8.5 kg
19 lbs
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 7
RM6173/6193
< 1.2 > Dimension - RM6193
Front View Side View
RP-H819
Bottom View
UNIT : mm
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
RM6193
480 x 53.3 x 354.8 mm
18.9 x 2.1 x 14 inch
529 x 124 x 495 mm
23 x 4.9 x 20.8 inch
6.5 kg
14 lbs
9 kg
20 lbs
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 8
RM6173/6193
< 1.3 > Installation
Step
1
¦ Mount the display panel with M6 screw set.
¦ M6 screw x 4 pcs required ( Left & right side ).
M6 screw sets are not provided.
Step
2
¦ Fix the LCD into the rack.
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 9
< Part 2 >
< 2.1 > Product Specifications
LCD
Panel
RM61 73
RM6193
Panel Size ( diagonal )
17-inch T FT color LCD
19-inch TFT color LCD
Display pixel ( dots x lines )
1280 x 1024
1280 x 1024
Brightness ( typ. )
1000
1000
Contrast Ratio ( typ. )
1000:1
1000:1
Color
16.7 M
16.7 M
Viewing Angle ( L/R/U/D )
85/85/80/80
80/80/80/80
Response Time ( ms )
5
5
Dot pitch ( mm )
0.264
0.294
Display Area ( mm )
337.92H x 270.33V
376.32H x 301.05V
Surface treatment
Anti-glare
Haze 25%, Hard-coating
Surface hardness
3H
3H
Backlight Type
LED
LED
MTBF ( hrs )
50,000
50,000
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
Analog
VGA
Analog 0.7Vp-p
Composite ( BNC )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kΩ / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Speaker Output
Power
2 x 2W
*When the audio out put is connected, speaker outpu t is OFF
Regulatory Safety Approval FCC & CE
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 10
RM6173/6193
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
35W or less
Power saving mode
4W or less
Power button OFF
1W or less
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
RM6173
RM6193
Product ( W x D x H )
480 x 54.2 x 310 mm
18.9 x 2.1 x 12.2 inch
480 x 53.3 x 354.8 mm
18.9 x 2.1 x 14 inch
Packing ( W x D x H )
529 x 124 x 495 mm
20.8 x 4.9 x 19.5 inch
529 x 124 x 495 mm
20.8 x 4.9 x 19.5 inch
Net Weight
6 kgs / 13 lbs
6.5 kgs / 14 lbs
Gross Weight
8.5 kgs / 19 lbs
9 kgs / 20 lbs
Applicable
Format
DVI-D / VGA Input
PC Signal
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 11
< 2.2 > On-screen Display Operation ( OSD )
RM6193
Power light
Green = On
Orange = Power saving
Membran e Sw itch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
RM6173
Membrane Switch Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting o ptions
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menu or
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power touch button will flash continuously when there is no signal input.
1
All th e LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power ).
2 L ight up all membrane buttons, please press any button for 1 - 2 seconds ( except the Power ).
Page 12
< 2.2 > On-screen Display Operation ( OSD )
OSD Configuration Page
Image:
for the brightness, contrast, color temp, red, green, and blue
Geometry:
for the auto adjust, H position, V position, phase and clock
Video:
for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for volume, bass, treble, balance, AVL and mute
Misc:
for the language, OSD position, graphic mode , ratio, reset and timer
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 13
< Part 3 >
< 3.1 > Optio ns : 3G / HD / SD -SDI input
Acn od es ’ SD I inpu t is an id ea l solutio n f or th e bro ad c ast grad e vide o an d h i g h resolut io n CCT V marke t.
Desig ne d fo r u s e wit h F ul l H D 1080 p a n d ultra high reso lutio n
192 0 x 120 0 L C D dis plays , Ac n od e s provi de s a SD I inp u t
modul e w itho u t usin g a d ditiona l spac e or p owe r an d i t com e s
st an dar d wit h a 2- year warran t y.
DVI - D
Audio
out - in - i n
Vide o PC
Po wer BNC S-Video VGA
SDI
ou t - in
HDMI
*** F or SDI opti o n, th e AD bo ard will be u pg raded to AV 3. 0, a nd this com e s sta ndard w ith H D M I, DVI -D,
VG A , S -V ideo , BN C and au dio inputs.
INPU T
3G - SD I I N
BNC x 1 / 0 .8 V p -p ( 75 o h m )
3G - SD I O UT
BNC x 1 / Active t hrough, eq u alized & r eloc ked
Sta nda rd C om pl ian c e
Video
SMPT E 4 25 M / 2 74 M / 296 M / 1 25 M
ITU -R B T.656
Audio
SMPT E 2 99 M / 2 72 M -C
Com pa tible Vi deo F or mat
3G - SD I
1080p @60 / 50Hz, 4:2 :2
1080p @30 / 25 / 24H z, 4 :4 :4
1080i @60 / 50Hz, 4:4 :4
720p @60 / 50Hz, 4:4 :4
HD -SD I
1080p @30 / 25 / 24H z, 4 :2 :2
1080i @60 / 50Hz, 4:2 :2
720p @60 / 50Hz, 4:2 :2
SD -SDI
480i @60H z, 4:2:2
IT U -R B T.6 56
576i @50H z, 4:2:2
Com pa tible Audio F or mat
3G - SD I
48kHz, 16 / 20 / 24 b it, 2 CH , Sync h roniz ed Video
HD -SD I
48kHz, 16 / 20 / 24 b it, 2 CH , Sync h roniz ed Video
SD -SDI
48kHz, 16 / 20 / 24 b it, 2 CH , Sync h roniz ed /
As ynchron ized V ideo
Max. T ra nsm is si on Dista nce
75 ohm c oax ia l c ab le
3G - SD I
150m at 2 .9 7G b/s
HD -SD I
250m at 1 .4 85 G b /s
SD -SDI
480m at 2 70 M b /s
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 14
< 3.2 > Options : MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64 units.
The RS-232C is used for the communication between the PC and the
first display via a 15 feet serial cable while the CAN bus is used for the
various LCD displays cascade together via CAT 5/6 cable, and daisy
chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides a
MCS input module without using additional space or power and it
comes standard with a 2-year warranty.
HDMI
Audio
Power BNC S-Video
out - in - in
Video PC
MCS
VGA DVI-D
set out in Link
*** For MCS option, casing depth will be changed.
RS-232C
Set switch
For the 1st and last display,
push the set switch upward
15 feet serial cable
( over 15 feet, extender required )
For other daisy chain displays,
push the set switch downwa rd
LINK OUT IN OUT IN OUT IN OUT
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
up to 64 displays
Page 15
< 3.3 > AV2.2D Upgrade Options :
- DVI-D
- AV
- Audio
( DVI-D TMDS single link )
( S-Video + Composite, BNC )
( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
DVI-D
Audio
out - in - in
Video PC
Power BNC S-Video VGA
< 3.4 > AV2.2H Upgrade Options :
- HDMI ( HDMI 1.1, CEA-861-D )
- AV
- Audio
( S-Video + Composite, BNC )
( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Audio
out - in - i n
Video PC
Power BNC S-Video VGA HDMI
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 16
< 3.5 > Options : Touchscreen & driver
H17” / H19" USB Touchscreen Specification
Model
Technology
Touch Point
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Haze
Glass
Connector
Compatibility
17’
19”
17”
19”
TRB e-Resistive
TCB e-Capacitive
5-Wire Resistive
Capacitive
Single
Single
Stylus or Finger
Finger
= 50g / Stylus=R0.8
= 50g
35 million touches
300 million touches
15 ms
20 ms
80% ± 3%
93% ±2%
3H
9H
8% ± 3%
7%
1.4 ±0.2 mm
3.2 ±0.2 mm
2.8 mm ±10%
2.8 mm ±10%
USB Type A
USB Type A
Windows 7 / XP / Vista, Linux
Windows 7 / XP / Vista, Linux
¦ USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
¦ For detailed information, please refer to the attached CD disc
¦ As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
DVI-D Power VGA
RM6173/6193
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 17
RM6173/6193
< 3.5 > Options : Touchscreen & driver
Please follow the below steps to setup the touch screen: -
Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 18
RM6173/6193
< 3.6 > Options : DC Power
Model
24V
48V
Input rating
Input voltage:
24-Volt
48-Volt
Input range:
18 ~ 36V
36 ~ 75V
Input current
- No load
50 mA
50 mA
- Full load
4880 mA
2442 mA
Output rating
Output voltage:
12-Volt
12-Volt
Output current:
8.3A
8.3A
Efficiency
85%
86%
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All right s reser ved . Produc t descr ipt ion and product speci fi cat io ns
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Page 19
RM6173/6193
< 3.7 > Options : MIL-type or Lockable Connector
Input
Part no.
MIL Standard
MIL - type
Connector
DC Power ***
( Male )
MS3470W8 -33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several addit ional MIL DC and VG A c onnector types with varying design
characteristics to meet cost considerations and to provide users with the m ost
design flexibility possible. For more information, please contact us.
Input
Part no.
Standard
Lockable
Connector
DC Power
( Male )
YM-Ext-461CP001
D-type 3W3
USB
LUSB - A111 - 00
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
17/19” 1000-nit High Brightness LCD Monitor
7/8U Rackmount Display Panel
14628 Ce ntral Ave,
Chino , CA 91710
tel:909.597.7 588, fax:909.597.1939
© Copyright 2013 Acnodes, Inc.
All righ ts reserved. Product descripti on and product speci ficat ions
are subj ect to change w ith out n oti ce. F or lates t product inform ati on,
ple ase vis it Acnod es’ we b site at www.ac nodes.c om.
Loading...