Acnodes PC 9150 User Manual

PC 9XX0

User Manual

PC 9XX0: 7 / 8 / 12 / 15” Industrial Panel PC with Dual-Core N2600 1.6GHz Processor

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

Industrial Panel PC

© Copyrigh t 2013 Acnodes, Inc. All rights reserv ed. Product description and product speci fications are subj ect to chan ge without notice. For latest produc t information , please visit Acnodes’ web site at www.acnode s.com.

PC 9XX0

Warning!

This equipment generates, uses and can radiate radio frequen cy en erg y and if not installed and used in accordance with t he instructions manual, it may cause interference to radio co mmunicati ons.

It has b een tested and found to compl y with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reason able pro tection against su ch interference w hen operated in a commercial enviro nment. Operation of this equipment in a residential area is likely to cause interference in which case th e user at his own ex pense will be required to take w hatever measures may be required to correct the interference.

Electric Shock H azard – Do not operate the m achine with its back cover removed. Th ere are

Industrial Panel PC

d angerous high volt ages inside.

Disclaimer

This information in this document is subject to change w ithout notice. In no event shall Acnodes Corp. be liable for damages of any kind, w hether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials.

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

© Copyrigh t 2013 Acnodes, Inc. All rights rese rved. Product des cript ion and product spec ifi cation s are subj ect to chan ge without notice. For latest produc t information , please visit Acnodes’ web site at www.acnode s.com.

PC 9XX0

Packing List

AC po wer cable

Driv er & manual CD disc

Other._ (please specify)

Industrial Panel PC

Accessories (as tick ed) includ ed in th is package are:

Safety Precautions

Follow the messages be low to prevent your systems from damage:

Avoid your system from static electricity on all occasions.

power-on. Always disconnect power when the system is not in use.

Prevent electric shock.

Disconnect power when you change an y hardware devices. For instance, when you

connect a jumper or install an y cards, a surge of power may damage the electronic

14628 Central Ave, Chin o, CA 91710 tel: 909.597.7588, fax:909.597.1939

components or the whole system.

Don’t

touch any components of this card when the card is

Table of Contents

Wa rning !………………………………………………………………………… ….……..….2 Disc laimer………………………………………………………………….…………………2 Pa cking List…………………………………………………………………………………..3 Safety Prec autions …………………………………………………………………………..3

Chapter 1 Getting Started

1.1 Specifications……………………………… ……..….……………………..6

1.2 Dimen sion s………………………………...………………………….......7

1.3 Brief Descriptio n………………………………………………….………10

1.4Installation of HDD…………………………………………………………11

Chapter 2 Hardw are

2.1 Mainb oard………………..…….……………………………………..…..15

2.2 Installatio ns…….………………… .……………………………………...18

2.3 Jumpers Setting an d Co nnectors........................................................19

Chapter 3 BIOS Setup

3.1 Operations after POST Scre en.............................................................28

3 .2 BIOS SETUP UTILITY..........................................................................29

3 .3 Main Settings…....................................................................................29

3 .4 Advanced Settin gs............................................................................... 31

3 .5 Chipset Settin gs................................................................................... 37

3 .6 Boot Settings....................................................................................... 41

3 .7 Secu rity Settings.................................................................................. 44

3 .8 Save and Exist Settings....................................................................... 45

3 .9 Exit Options..........................................................................................5 1

Chapter 4 Installation of Drivers

4.1 Chipse t Driver.…………………………...……………………………..…54

4.2 Graphics Media Accelerator Driver...……………………….…………..57

4.3 Netwo rk Ad ap ter……..…………………………………………………….60

4.4 Realtek ALC662 HD Audio Drive r Installation …….………….…………62

Chapter 5 Touch Screen Installation

5 .2 Windows 2 000/X P USB Drive r Installatio n for PenMount 6000Series.64

5.1.1 Installing Software (Resistive To uch).................................................6 4

5.1 .2 Installing S oftware (Pro jected Capacitive)..........................................69

5.2 .1 Software Functions(Resistive Touch)...............................................74

5.2 .2 Software Functions(Projected Capa citive)…………………………….85

Figu

res

Fig ure 1.1 :Dime nsion s of PC 90 70………………………………………..…....7

Fig ure 1.2 :Dime nsion s of PC 90 80………………………………………..…....8

Figure 1.3:Dimensions o f PC 9 12 0 …...…………………………………….8 Figure 1.3:Dimensions o f PC 9 15 0 …… ………………… ………………….9 Fig ure 1.4: Front Vie w of PC 9XX 0 SERIES………………………………...1 0 Fig ure 1.5: Rear View of PC 9070/PC 9 080……………………….………..10 Fig ure 1.5: Rea r View of PC 9120 /PC 9150……… ….……………………..11

Fig ure 2.1: Mainboard Dime nsions…………………………………..…….....17

Fig ure 2.2: Ju mpe rs an d Connectors Location_ Board Top………………...18

Fig ure 2.3: Jumpers and Co nnectors Location_ Board Botto m…………....1 9

Chapter 1 System

PC 9070

PC 9080

PC 9120

PC 9150

System

CPU

Atom Cedar View N2600 1.6GHz Dual Core Processors

System Chipset

NM10

Sys tem Memory

Onboard DDR3 2GB 800 MHz

IO Port

USB

2 x USB 2.0 type A, USB4/5

Serial/Parallel

1 x RS-232/422/485 DB-9, COM1, Default RS-232 1 x RS-232 DB-9, COM2

Audio

1 x Line out phone jack

LAN

2 x GbE RJ -45

Power

3 pins terminal block connector, DC Power input

Storage Space

HDD

1 x 2.5” SATA 2 half size

1 x 2.5” SATA 2

Movable device

1 x Internal SD slot

Expansion

On board

expansion bus

1 x Mini-PCIe half size

Display

Display Type

7” TFT-LCD

8”TFT-LCD

12.1”TFT-LCD

15”TFT-LCD

Max. Resolution

800x480

800x600

1024x768

Max. Color

262K

16.2M

Luminance

(cd/m²)

350

330

400

View

angle(H°/V°)

140/110

140/125

160/140

160/145

Touch screen

Type

Resistive Touch / Projected Capacitive Tou ch (Option)

Interface

RS-232 / USB

Light

Transmission(%)

80% / 90%

1.1 Specifications

P ower

Power Input

9~36V DC

Mechanical

Construction

Sliver aluminum front bezel and chassis

IP Rating

IP65 front panel

Mounting

Panel mounting, VESA 75 x 75

Dimension (mm)

202 x 149 x 39

231 x 176 x 51

319 x 245 x 51.68

410 x 310 x 54.67

Net Weight (Kgs)

2.3

3.2

4.0

6.3

Environmental

Operatiing

temperature(°C)

0~50℃

Storage

temperature(°C)

-20~60℃

Storage humidity

10 to 90% @

40°C,

non- condensing

Certification

CE / FCC Class A

Operating

System Support

Windows XP pro, Windows XP Embedded, Windows Embedded CE6.0(Note 1), Windows 7 pro for Embedded Windows Embedded standard 7(Win 7 support 3D Graphic function)

Note 1: PC9XX0 series is covered by one or more of the following patents: US6, 570, 884, US6,115,776, and US6,327,625.

1.2 Dimensions

Figure 1.1: Dime nsions of PC9070

F igure 1.2: Dime nsions of PC9080

F igure 1.3: Dime nsions of PC9120

Figure 1.4: Dimensions of PC9150

1.3 Brief Description of PC9XX0 SERIES

There are 7”, 8”, 12”,15 ” Industrial Compact Size Panel PC in PC9XX0 series, which comes with flat front panel touch screen and fanless d esign. It is powered by an Intel Atom N2600 1.6GHz CPU

built-in, 2GB DDR III 800 MHz. PC9XX0 series is 9~36VDC wide-ranging power input and IP65 compliant f ront panel. Optional projected capacitive touchscreen support 7H anti-scratch surface is ideal for us e as a PC-based controller f or Industrial Automation & Factory Automation.

Figure 1.5 : Front View of PC9XX0 SERIE S

Figure 1.6: Re ar View of PC 9070 / PC 9080

Step 1

There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws.

Step 2

There is a SSD card in the bracket. Gently remove the screw, then carefully pull SSD card.

Figure 1.7: Rear View of PC 9120/ PC 9150

1.4 Installation of HDD(PC9070/PC9080)

Step 3

Take out SSD Card bracket.

Step 4.

You can replace SSD card by unscrewing 4 screws as shown in the picture. Note: 4 screws are packed in the packing lis t.

Step 5

There is a SD card hole in the side of the machine. You can replace SD card from there.

Step 6.

Gently screw the screws.

Installation of HDD(PC 9120 / PC 9150)

Step 1

There are 2 screws to deal with when enclosing or removing the chas sis. Gently remove 2 screws.

Step 2

You c an put or remove HDD into the machine by pulling the HDD bracket.

Step 3

You can remove HDD by unsc rewing 4 screws in the HDD bracket. Note: 4 screws are packed in the packing list.

Step 4

There is a SD hole in the side of machine. You can replace SD card from there .

Chapter 2 Hardware

Specifications

Board Size

170mm x 113mm

CPU Support

Atom N2600 /1.60GHz

Chipset

NM10 Express

Memory Support

Onboard 2GB DDRIII SDRAM

Graphics

Integrated GMA 3600 (N2600)

Display Mode

1 x CRT Port

1 x LVDS1 (18/24-bit single LVDS)

Support Resolution

Up to 1920 x1200 for CRT Up to 1366 x768 for LVDS1 (N2600)

Dual Display

CRT+LVDS1

Super I/O

Winbond W83627UHG-E

BIOS

AMIBIOS

Storage

1 x SATA Connector (7P)

1 x SATA Connector (7P+15P) 1 x SD Socket (USB to SD)

Ethernet

2 x PCIe GbE LAN by Realtek RTL8111E

2 x USB 2.0 (type A)stack ports (USB4/USB5) 2 x USB 2.0 Pin header via CN3 (USB2/USB3) 2 x USB 2.0 Pin header via CN1 (USB0/USB1) 1 x USB 2.0 for MPCIE1 (USB7) Mini-PCIe(USB7)

USB

Serial

1 x RS-232/RS-422/RS-485, DB9 connector for external

(COM1)

pin 9 w/5V/12V/Ring

select

1 x RS232 port, DB9 connector for external (CO M2)

pin 9 w/5V/12V/Ring

select 1 x RS422/485 header via CN2 (COM3) 2 x UART via CN3 (COM5,COM6)

Digital I/O

8-bit digital I/O Pin header via CN2

2.1 Mainboard

4-bit digital Input 4-bit digital Output

4-bit digital I/O Pin header via CN3

2-bit digital Input 2-bit digital Output

Battery

Support CR2477 Li battery by 2-pin header

Audio

Realtek ALC662 HD au dio codec

Line-in, Line-out, MIC via 2x6-pin header Audio Line out in phone jack

Ke yboard /Mouse

1 x PS2 keyboard/mouse 1x6 box pin header via CN3

Expansion Bus

1 x mini-PCI-express slot 1 x PCI-express via CN3

Touch Ctrl

1 x Touch control header for TCH1 (COM4)

Pow er Management

Wide Range DC 9~36V input 1 x 3-pin power input connector

Sw itches and LED Indicators

1 x Powe r on/off switch via CN1 1 x Reset switch via CN1

1 x Power LED status via CN 1

1 x HDD LED status via CN1 1 x Buzzer

External I/O port

2 x COM Ports (COM1/CO M2) 2 x USB 2.0 Ports (U SB4/USB5) 2 x GbE LAN Ports 1 x Line out Audio phone jack

Watchdog Timer Software programmable 1 – 255 second by Super I/O

Temperature

O perating: -20 to 70

Storage: -40 to 85

Humidity

5% - 95%, non-condensing, operating

Pow er Consumption

12V /0.95A (Intel Atom N2600 processor with 2GB DDR3

DR AM)

EMI/EMS

Meet CE/FCC class A

(units :mm)

Figure 2.1: Mainboard Dimensions

2.2 Installations

SBC-7106 is a 4" industrial motherboard developed on the basis of Cedarview-M Processors and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE c onfiguration, one VGA port, one HDMI port, one LVDS interface. To s atisf y the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely us ed in various sectors of industrial control.

2.2.1 Jumpe rs Setting and Conne ctors

Board Top

Figure 2.2: Jumpers and Connectors Location_ Board Top

JP5 Mode

Open

ATX Power

Auto Pow er on

(Default)

Board Bottom

Figure 2.3: J umpers and Connec tors Loca tion_ Board Bottom

2.3 Jumpers Setting and Connectors

1. JP5:

(2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting.

3. BAT1 :

Pin#

Signal Name

Pin1

VBAT

PIN2

Ground

Pin#

Power Input

Pin1

DC+9V~32V

Pin2

Ground

Pin3

Signal Name

Pin#

Signal Name

CRT_RED

1 2 Ground

CRT_GREEN

3 4 Ground

CRT_BLUE

5 6 Ground

CRT_H_SYN C

7 8 CRT_D DCDAT

CRT_V_SYNC

9 10

CRT_D DCCL K

Ground

11 12

Ground

(1.25mm Pitch 1X2 box Pin H eader) 3.0V Li battery is embedded to provide power for CMOS.

4. DC_IN1:

(5.08mm Pitch 1x3 Pin Connector),DC9V~36V System power input connector

6. VGA1:

(CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to VGA Port.

8. JP1:

JP1 Pin#

Function

Close 1-2

COM1 RI (Ring Indicator)

(default)

Close 3-4

COM1 Pin9=+5V

(option)

Close 5-6

COM1 Pin9=+12V

(option)

Func tion

S_232 Pin#

RS232

(Default)

ON: Pin1, Pin2, Pin3, Pin4

RS422

(option)

OFF: Pin1, Pin2, Pin3, Pin4

RS485

(option)

OFF: Pin1, Pin2, Pin3, Pin4

Func tion

RS_422 Pin#

RS232

(Default)

OFF: Pin1, Pin2, Pin3, Pin4

RS422

(option)

ON: Pin1, Pin2, Pin3, Pin4

RS485

(option)

ON: Pin1, Pin2, Pin3, Pin4

(2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal

out of pin 9 of COM1 port.

9. RS-232:

(Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output.

10. RS-422:

(Switch),COM1 setting, it provides selectable R S232 or RS422 or RS485 serial signal output.

Note: M us t k eep the setting with BIOS setting.

11. COM1:

R S232 (Default):

Pin#

Signal Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

JP1 select Setting (RI/5V/12V)

BIOS Setup Advanced/W83627UHG Super IO

C onf iguration/Serial Port 1 Configuration RS-232

R S422 (option):

Pin#

Signal Name

422_RX+

422_RX-

422_TX-

422_TX+

Ground

BIOS Setup Advanced/W83627UHG Super IO

C onf iguration/Serial Port 1 Configuration RS-422

(Type DB9 ),Rear serial port, standard DB9 Male serial port is provided to make a direct

connection to serial devices. CO M1 port is controlled by pins No.1~6 of JP1,select output Signal RI or 5V or 12 V, For details, please refer to description of JP1 and S_232 and S_422 setting.

RS485 (option):

Pin#

Signal

Name

485-

485+

Ground

BIOS Setup Advanced/W83627UHG Super IO

Conf iguration/Serial Port 1 Configuration RS-485

JP2 Pin#

Function

Close 1-2

COM1 RI (Ring Indicator)

(default)

Close 3-4

COM1 Pin9=+5V

(option)

Close 5-6

COM1 Pin9=+12V

(option)

12 JP2:

(2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select s ignal

out of pin 9 of COM2 port.

13. COM2:

Pin#

Signal

Name

DCD# (Data Carrier Detect)

RXD (Received Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

Ground

DSR (Data Set Ready)

RTS (Request To Send)

CTS (Clear To Send)

RI (Ring Indicator)

(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a

direct connection to serial devices.

16. LED3:

LED STATUS. Green LED f or Touch Power status.

19 SAT A1:

(SATA 7Pin+15Pin), SATA Connectors, one SATA connectors are provided, with transfer

speed up to 3.0Gb/s.

20 SD1:

(SD card socket),Secu re Digital Mem ory Card s oc k et.

23. LINE_OUT:

(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to provide high quality audio I/O ports. Line Out can be connected to a headphone or amplifier.

24. USB45:

USB4/USB5 (Double stack USB type A), Rear USB connector, it provides up to 4

USB2.0 ports, High-speed USB 2.0 allows da ta transf ers up to480 Mb/s ,s upport USB full-speed and low-speed signaling.

Each USB Type A Re ceptacle (2 Ports) Current limited value is 1.5A.

If the external USB device current exceeds 1.5 A, please separate connectors into different Receptacle.

25. LAN1/LAN2:

LAN1/LAN2: (RJ 45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45

Ethernet ports are provided. Used Realtek RTL8111E chipset, LINK LED (green) and ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN.

26. BUZ1:

Onboard buzzer.

27 LED1:

LED STATUS. Green LED for Motherboard Pow er status.

28. LED2:

Function

Signal Name

Pin#

Signal Name

Function

5V_S5_USB

1 2 5V_S5_USB

5V_S5_USB

3 4 5V_S5_USB

USB23_OC

5 6

CLKREQPSON_ATX-

USB2

USB2_N

7 8 USB2_P

USB2

USB3

USB3_N

9 10

USB3_P

USB3

Ground

PS/2 MS

PS2_MSCLK

PS2_MSDATA

PS/2 MS

PS/2 KB

PS2_KBCLK

PS2_KBDATA

PS/2 KB

COM6 (UART)

COM6_RI

COM6_DCD-

COM6 (UART)

CO M6_TXD

COM6_RXD

COM6_DTR

RICOM6_RTS

COM6_DSR

COM6_CTS-

Ground

COM5 (UART)

COM5_RI

COM5_DCD-

COM5 (UART)

CO M5_TXD

COM5_RXD

COM5_DTR

DSRCOM5_RTS-

COM5_DSR

DTRCOM5_CTS-

GPIO24

ICH_GPIO24

ICH_GPIO13

GPIO13

GPIO26

ICH_GPIO26

ICH_GPIO27

GPIO27

Ground

PCIE

PE1_TX_N0

PE1_TX_P0

PCIE

PE1_RX_N0

PE1_RX_P0

Ground

CLK_100M_PE1_N

CLK_100M_PE1_P

PM_PCIE_WAKE

PLTRST_BUF-

SMBUS

SMB_CLK_S

SMB_DATA_S 5

SMBUS

PCIE

PE1_CLKRE

Ground

PCIE

3P3V_S5

LED STATUS. Green LED f or Motherboard Standby Power Good statu s.

31. CN3:

(1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO, Two USB 2.0,one PS/2 mouse one PS/2 keyboard,two uart,one PCIe x1,one SMbus.

3P3V_S5

12V

12V_S0

12V

3 BIOS Setup Description

3.1 Operations after POST Screen

After CM OS discharge or BIOS flashing operation,.Press [Delete] k ey to enter CMOS Setup.

After optimizing and exiting CMOS Setup, the P OST screen displayed for the first time is as follows and

BIOS Date: 12/17/2012 02:22:46 Ver: 7106V002

Press DEL or F2 to enter setup

includes bas ic information on BIOS , CPU, memory, and s torage devices.

3.2 BIOS SETUP UTILITY

Main

Advanced

Chipset

Boot

Security

Save & Exit

BIOS Information

BIOS Vendor American Megatrends Core Version 4.6.5.3 Compliancy UEFI 2.3; PI 1.2 Project Version 7106V002

Build Date and Time 12 17 2012 03:22:46

Intel RC Version

System Language [English]

System Date [Sun 01/01/2012] System Time [00:00:08]

Access Level Administrator

Intel Reference Code Version

: Select Screen

: Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit

ESC Exit

Press [Delete] key to enter BIOS S etup utility during P OST, and then a main menu containing system summ ary information will appear.

3.3 Main Settings

BIOS Info rmatio n BIOS Vendor American Megatren ds Core Version 4.6.5 .3 Compliancy UEFI 2.3; P I 1.2 Project Version 7106V00 2 Build Date and Time 12 17 2012 03:22:46

? Intel RC Version

Intel Reference Code Version

System Lan gu age [English]

System Date [Sun 01/01/2012] System Time [00:00:08]

Access Level A dministrator

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1

: General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit

System Time:

Set the system time, the time format is:

System Date:

Set the system date, the date format is:

Day: Note that the

„Day? automatically changes when you set the date.

Month: 01 to 12 Date: 01 to 31 Year: 1998 to 2099

Minute : 0 to 59

Hour : 0 to 23

Second : 0 to 59

ESC Exit

3.4 Advanced Settings

Main

Advanced

Chipset

Boot

Security

Save & Exit

 PCI Subsystem Settings  ACPI Settin gs  CPU Con figuration  Thermal Configuration

 ID E Configuration  USB Configuration  W8362 7UHG Super IO Configuration  W8362 7UHG HW Monitor  Serial Port Console Redirection

 PPM Configuration

PCI,PCI-X and PCI Express Settings

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit

3.4.1 PCI Subsystem Settings

PCI Bus Driver Versio V2.05.02

PCI Common Settings: PCI Latency Timer:

[32 PCI Bus Clocks]

[64 PCI Bus Clocks] [96 PCI Bus Cloc ks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks]

VG A Palette Snoop:

[Disabled]

[Enabled]

PERR# Generation:

[Disabled]

SERR# Generation:

3.4.2 ACPI Settings Enable ACPI Auto Conf:

Enable Hibernation:

ACPI Sleep State:

[Enabled]

[Disabled]

[Enabled]

[Disabled]

[Enabled]

[Disabled]

[Both S1 and S3 available for OS to choose from ]

Lock Legacy Resources:

S3 Video Repost:

3.4.3 CPU Configuration

Processor Type Intel(R) Atom(TM) CPU N2600 EMT64 Processor Speed 1600 MHz System Bus Speed

[Suspend

Disabled] [S1 only(CPU Stop Clock) ] [S3 only (Suspend to RAM) ]

[Disabled]

[Enabled]

[Disabled] [Enabled]

Not Supported

400 MHz Ratio Status 16 Actual Ratio 16 System Bus Speed 400 MHz Processor Stepping 30661 Microc ode Revision 269

L1 Cache RAM

Passive TC1 Value

Passive TC2 Value

Passive TSP Value

2x56 k L2 Cache RAM Processor Core Dual

Hyper-Threading Supported

Hyper-Threading:

Execute Disable Bit:

Limit CPUID Maximum:

3.4.4 Thermal Configuration

2x512 k

[Enabled] [Disabled]

[Disabled] [Enabled]

CPU Thermal Configuration

DTS SMM

Platf orm Thermal Configuration

Critical Trip Point [POR] Active Trip Point Lo [55 C] Active Trip Point Hi [71C] Passive Trip Point [95]

3.4.5 IDE Configuration SATA Port0 Not Present SATA Port1 Not Present

SATA Controller(S):

Configure SATA as:

[Disabled]

[Enabled]

[Disabled]

[IDE]

[AH

CI]

Misc C onfiguration for hard disk

3.4.6 USB Configuration

USB Configuration USB Devices:

Legacy USB Support:

EH CI Hand-off:

USB hardware delays a USB transfer time-out:

Device reset time-out:

Device power-up delay

Mass Storage D evic es Multiplecard Reader 1

1 Drive 1 keyboard

[Enabled] [Disabled]

[Disabled] [Enabled]

[20 sec] [10 sec] [5 sec] [1 sec]

[20 sec] [10 sec] [30 sec] [40 sec]

[Auto] [Manual]

[Auto]

3.4.7 W83627UH G Super IO C onfiguration W83627UHG Super IO ch W83627UHG Serial Port 1 Conf iguration

UART Mode Selection

[Floppy] [Forced FDD] [Hard Disk ] [CD-ROM]

[RS-232]

[R S-485]

VSB5

: +5.203 V

VBAT

: +3.334 V

Serial Port 2 C onf iguration Serial Port 3 C onf iguration

UART Mode Selection

Serial Port 4 C onf iguration Serial Port 5 Configuration Serial Port 6 Configuration Power Failure

3.4.8 W83627UHG HW Monitor

[R S-422]

[RS-485] [R S-422]

[Keep las t state] [Always off ] [Always on]

PC Health Status

System temperature1 : +38 System Speed : N/A

VCORE +12V +3.3V : +3.320 V +1.5V : +1.528 V AVCC : +5.203 V VC C5V

3.4.9 Serial Port Console R edirection COM0

Console Redirection

Console Redirection Settings

: +0.968 V

: +12.302 V

: +5.216 V

[Enabled] [Disabled]

Serial Port f or Out-of-Band Management/

W indows Emergency Management Services (EMS)

Console Redirection

Console Redirection Settings

3.4.10 PPM Configuration

PPM Conf iguration EIST:

CPU C state Report

Enhanced C state

CPU Hard C4E

[Disabled] [Enabled]

[Enabled] [Disabled]

C PU C6 state

C 4 Exit Timing

C-state POPDOWN

C-state POPUP

[Enabled] [Disabled]

[Fast] [Default] [Slow]

[Enabled] [Disabled]

3.5 Chipset Settings

Main

Advanced

Chipset

Boot

Security

Save & Exit

 Host Bridge

 Sou

h Bridge

Host Bridge Parameters

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit

3.5.1 Host Bridge

M emory Frequency and Timing Intel IGD Configuration

******* M em ory Information ******* Memory Frequenc y 800 MHz(DDR3) Total Memory 2048 MB DIMM#0 Not Present DIMM#1 2048 MB

Memory Frequency and Timing

MRC Fas t B oot

Max TOLUD

[E nabled]

[Disabled]

[Dynamic]

[1GB ] [1.25GB ]

[1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB]

[3.25GB]

Intel IGD Configuration

IGFX – Boot Type

LCD Panel Type

[VBIOS Default] [VGA] [LVDS] [VGA + LVDS ]

[VBIOS Default] [640x480 18bit]

[800x480 18bit] [800x600 18bit] [1024x600 18bit ] [1024x768 18bit ] [1280x768 18bit ] [1280x800 18bit ] [1280x1024 18bit] [1366x768 18bit] [1024x768 24bit] [1280x768 24bit] [1280x800 24bit] [1280x1024 24bit]

P anel S caling

[Auto] [Force Scaling] [off]

[Maintain A spec t Ratio]

A ctive LFP

[LVDS] [No LVDS ]

IGD Clock Source

[External Clock] [Internal Clock ]

Fixed Graphics Memory

[128MB] [256MB]

A LS Support

[Disabled]

[Enabled]

B ack light Control

[DC]

[PW M]

B ack light Logic

[Positive]

[Negative]

B ack light Control Lev

[Auto] [Disabled] [Level 8] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] [Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15]

3.5.2 S outh Bridge TP T Devices PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3

DMI Link ASP M Control

PCI-E xp. High Priorit

High P recis ion E vent Timer Configuration High P recis ion Timer

SLP_S4 Assertion Widt

Restore AC Power Loss

[Enabled] [Disabled]

[Disabled]

[Enabled]

[Disabled]

[1-2 Sec onds] [2-3 Sec onds] [3-4 Sec onds] [4-5 Sec onds]

[Last State] [Power off] [Power on]

3.6 Boot Settings

Main

Advanced

Chipset

Boot

Security

Save & Exit

Boot Configuration

Setup Prompt Timeout 1

Bootup Numlock State [On]

Quiet Boot

[Disabled]

Fast Boot

[Enabled]

Skip USB

[Disabled]

Skip PS2 [Disabled]

CSM16 Module Version 07.69

Gatea20 Active

[Upon Request] Option ROM Messages [Force BIOS] Interrupt 19 Capture

[Enabled]

Driver Option Priorities Boot Option Priorities

Boot Option Priorities

Boot Option #1 [SATA PM: Hitachi…] Boot Option #2 […]

Hard Drive BBS Priorities

CSM Parameters

Number of seconds to Wait for setup Activation key. 65535(0xFFFF)means Indef inite waiting.

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit

Setup Prompt Timeout [1]

Bootup Numlock State

Quiet B oot

[On ] [ off]

[Disabled]

Fast B oot

Skip VGA

Skip USB

Skip P S2

C SM16 Module Version 07.69

Gatea20 Active

Option ROM Messages

Interrupt 19 Captu re

B oot Option #1

Boot Option #2 ……

Har d Drive BBS Prior ities [SATA PM:*** … ]

Sets the system boot order

B oot Option #1

SATA P M:***…

[E nabled]

[Disabled]

[E nabled]

[Disabled]

[Disab led]

[Enabled]

[Disab led]

[Enabled]

[Upon R equest]

[Always]

[Force B IOS] [Keep C urrent]

[Im mediate]

[Postponed]

C SM Parameters

Launch CS M

****** Disabled

[Always]

[Ne ver]

B oot option filter

[UEFI and Legacy] [Legac y only] [UEFI only]

Launch P XE OpROM poli

[Do not Launch] [UEFI only]

[Legac y only]

Launch Storage OpROM

[Legacy only] [Do not Launch]

[UEFI only]

Launch Video OpROM po

[Do not Launch] [UEFI only]

[Legac y only]

Other PCI device ROM

[UEFI OpROM ] [Legacy OpROM]

3.7 Security Settings

American Megatrends, Inc.

Main

Advanced

Chipset

Boot

Security

Save & Exit

Password Description

If ONLY the Administrator?s password is set, Then this only limits access to Setup and is Only asked for when entering Setup.

If ONLY the User?s password is set, then this Is a power on password and must be entered to

Is a power on password and must be entered to Boot or enter Setup. In Setup the User will Have Administrator rights. The password length must be In the following range: Minimum length 3 Maximum length 20

Administrator Password

User Password

Set Administrator Password

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit

6.4.1 Administrator Password

6.4.2 User Password

Type the passwo rd with up to 20 characters and then pr ess Enter key. This will clear all previously typed CM OS pas swor ds . You will be requested to confirm the password. Type the pass word again and press  Enter key. You m ay press Esc key to abandon pass word entry operation. To c lear the password, just pres s E nter k ey when pass word input window pops up. A c onfirmation m essage will be shown on the screen as to whether the password will be disabled.

You wi ll have dir ec t access to BIOS setup without typing an y password after s ys tem reboot once

BIOS SETUP

UTILITY

Main

Advanced

PCIPnP

Boot

Security

Chipset

Exit

Advanced Chipset Settings

Configure North Bridge feature

Select Screen Select Item

Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit

WARNING: Setting wrong values in below

sections

may cause system to malfunction

 North Brid ge Configu ration

 South Bridge Configuration

V02.61

the pas swor d is disabled. Onc e the password feature is used, you will be requested to type the password each time you enter B IOS setup. This will prevent unau thorized pers ons from changing your system configurations.

3.8 Save and Exist Settings

Also, the feature is capable of requesting users to enter the password prior to s ys tem boot to control unauthorized access to your com puter. Users may enable the feature in Security Option of Advanced B IOS Features . If Security Option is set to System, you will be requested to enter the pas swor d before system boot and when entering BIOS setup; if Security Option is set to Setup, you will be reques ted for pass word for entering BIOS setup.

Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in

BIOS Setup. If the connected panel is not included in the parameter list, display problem will occur. In this c ase, Please do not change BIOS setup.

3.8.1 North Bridge Configuration

BIOS SETUP

UTILITY

Chipset

North Bridge Chipset Configuration

ENABLE: Allow Remapping of Over lapped PCI Memory Above the total Physical memory

DISABLE: Do not allow remapping of memory

Select Screen Select Item

+- Charge Field F1 General Help F10 Save and Exit ESC Exit

Memory Remap Feature

[Enabled]

PCI MMIO Allocation: 4Gb To 3072MB

Memory Hole [Disabled]

Initate Graphic Adapter [PCI/IGD]

IGD G raph ics Mode Select [Enabled ,64 MB]

IGD GTI Graphic smemory size [No VT mod e,2MB]

PEG Port Configuration

 Video Fun ction Configu ration

V02.61

Memory Remap Feature:

Memory Hole:

Initate Graphic Adapter:

Select which graphics controller to use as the primary boot device.

IGD Graphics Mode Select:

[

Enabled]

[Dis

abled]

[Disabled] [15MB-16MB]

[

IGD]

[PCI/IGD]

[Enabled, [Disabled]

64MB]

[Enabled, 32MB]

BIOS SETUP

UTILITY

Chipset

Video Functio n Configuration

Options Fixed Mode DVMT Mode

Select Screen Select Item

+- Charge option F1 General Help F10 Save and Exit ESC Exit

DVMT Mode Select [DVM Mode]

DVMT/FIXED Memo ry

[25 6MB]

Boot Display Device

[V BIO S-Default]

Flat Panel Type [1024x768 18bit 1c]

Backlight Control Support [V BIO S-Default]

Backlight Control Level [Level 5]

Backlight Control Mode [DC]

Backlight Image Adaptation [V BIO S-Default]

V02.61

[Enabled, 128 MB]

Video Function Configuration:

DVMT Mode Select:

[DVMT Mode] [FIXED Mode]

DVMT/FIXED Memory Size:

[256MB] [128MB] [Maximum D VMT]

Boot Display Device:

[BIOS-D efault] [CRT]

[LVDS] [CRT + LVDS]

Flat Panel Type:

[1024x 768 18bit 1ch]

[640x480 18bit 1ch]

[800x600 18bit 1ch] [1280x800 18bit 1ch] [1366x768 18bit 1ch]

[1024x 768 24bit 2ch]

[1440x900 24bit 2ch]

[1600x900 24bit 2ch] [1680x1050 24bit 2ch] [1920x1080 24bit 2ch]

Backlight Control Support

[V BIOS-D efault]

[Both BLC & BIA Disabled]

[BLC Enabled]

Backlight Control Control:

[Level5]

[Level0] [Level1] [Level2] [Level3] [Level4] [Level6]

Note: Panel support PWM

[Level7]

Function.

Backlight Control Mode:

[DC]

[PWM]

Backlight Image Adaptation:

[VBIOS-Default]

[BIA Dis abled] [BIA Enabled at Level1] [BIA Enabled at Level2]

[BIA Enabled at Level3]

Main

Advanced

Chipset

Boot

Security

Save & Exit

Save Changes and Exit

Discard Changes and Exit Save Changes and Reset Discard Changes and Reset

Save Options

Save Changes Discard Changes

Restore Defaults Save user Defaults Restore user Defaults

Boot Override

MultipleCard Reader 1.00 SATA PM:*** …

Launch EFI Shell from filesystem device

Exit system setup after Saving the changes.

: Select Screen : Select Item

Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit

[BIA Enabled at Level4] [BIA Enabled at Level5]

3.8.2 South Bridge Configuration:

Save Changes and Exit

Save & Ex it Setup save C onfig uration and exit ?

D iscard Changes and Ext

Exit With out Saving Quit witho ut saving?

Save Changes and Reset

Save & reset Save Con figu ration and reset?

[Yes] [No ]

[Yes]

Discard Ch anges and Reset

Reset Without Savin g Reset without savin g?

Save Changes

Save Setu p Values Save configuration?

Discard Ch anges

Load Previous Values Load Previous Values?

Restore Defaults

Load Optimized Defaults Load optimized Defaults?

Save user Defaults

Save Values as User Defaults Save configuration?

Restore user Defau lts

Resto re User Defau lts Restore User Defaults?

Launch EFI Sh ell from filesystem device

WARNING Not Found

[No]

[Yes] [No]

[ok]

3.9 Exit Options

BIOS SETUP

UTILITY

Main

Advanced

PCIPnP

Boot

Security

Chipset

Exit

Exit Options

Exit system setup after saving the changes

F10 key can be used For this operation

Select Screen Select Item

Enter Go to sub screen F1 General Help F10 Save and Exit ESC Exit

Save Changes and Ex it

Discard Changes and Exit

Discard Changes

Load Optimal Defaults

Load Failsafe D efaults

V02.61

Save Changes and Exit:

Save c onf iguration changes and exit setup? (F10 key can be used for this operation)

[OK] [Cancel]

Discard Changes and Exit:

Discard C hanges and Exit setup? (ESC key can be used for this operation)

[OK] [Cancel]

Discard Changes:

Disc ard changes? (F7 key can be used for this operation)

[OK] [Cancel]

Load Optimized D efaults:

Load Optimized Defaults? (F9 key can be used for this operation)

[O K]

[Cancel]

Load Fail-Safe Defaults:

Load Fail-Safe Defaults? (F9 key can be used for this operation)

[O K]

[Cancel]

Chapter 4 Installation of Drivers

This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Chipset driver,

VGA driver, LAN dri vers, Audio driver Installation instructions are given below.

Important Note:

After installing your Windows operating system (W indows XP), you must install first the Chipset Software Installation Utility before proceeding with the

installation of drivers.

4.1 Chipset Driver

To install the chipset driver, please f ollow the steps below.

Step 1. Select Intel (R) Chipset NM10 Express f rom the list

Step 2. Click Next to setup program.

Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement.

Step 4. Click Next to continue.

Step 5. Click Next.

Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any ins tallation

media from the drives.

4.2 Graphics Media Accelerator driver

To install the VGA drivers, follow the steps below to proceed with the installation.

Step 1.Select Intel(R) VGA Chipset Driver.

Step 2. Select Installs driver and application files. Click Next.

Step 3. Select I agree. C lick Install.

Step 4. C lick Continue Anyway.

Step 5. C lick Continue Anyway.

Step 6. To restart the computer, click Yes.

4.3 Network Adapter

To install the Network Adapter device driver, please follow the steps below.

Step 1. Select Realtek RTL8111D Driver.

Step 2. Click Next to continue.

Step 3. C lick Install to begin the installation.

Step 4. Click Finish to exist the wizard.

4.4 Realtek ALC662 HD Audio Codec Driver Installation

To install the R ealtek ALC662 HD Audio Codec Driver, please f ollow the steps below.

Step 1. Select Realtek AL662 Audio Codec Driver from the list

Step 2. Click Next to continue.

Step 3. Click Yes, I want to restart my computer now . Click Finish to complete the installation.

Chapter 5 Touch Screen Installation

This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems.

5.1 Windows 2000/XP/2003/Vista/WIN7 Universal Driver Installation for PenMount 6000 Series

Bef ore installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer. You must also have one of the following PenMount 6000 series controller or control boards installed: PM6500, PM6300.

5.1.1 Installing Software(Resistive Touch)

If you have an older version of the PenMount Windows 2000/XP driver installed in your s ys tem, please remove it first. Follow t he steps below to ins tall the PenMount DMC6000 W indows 2000/XP driver.

Step 1. Ins ert the product CD, the screen below would appear. Click touch panel driver.

Step 2. Select Resisti ve Touch.

Step 3. Click Next to continue.

Step 4. Read the license agreement. Click I Agree to agree the license agreement.

Step 5. Choose the folder in which to install PenMount W indows Universal Driver. Click Install to

start the installation.

Step 6. Wait for installation. Then click Next to continue.

Step 7. Click Continue Anyw ay.

Step 8. Click Finish to complete ins tallation.

5.1.2 Installing Software (Projected Capacitive)

Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.

Step 2. Select Projected Capacitive.

Step 3. Click Next to continue.

Step 4. Select I accept the terms of the license agreement. Click Next.

Step 5. Tic k Install RS232 interface driver. Click Next.

Step 6. Select None. Click Next.

Step 7. Click OK.

Step 8. Tic k Support Muti-Monitor System. Click Next.

Step 9. Go to C:\Program Files\eGalaxTouch. Click Next.

Step 10. Click Next.

Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next.

Step 12. Wait f or installation.

Step 13. Click Yes to do 4 point calibration.

5.2.1 Software Function s(Resistive Touch)

Upon rebooting, the computer automatically f inds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration.

1. After installation, click the PenMount Monitor icon “PM” in the menu bar.

2. W hen the PenMount Control Panel appears, select a device to “Calibrate.”

PenMount Control Pane l(Resistive Touch)

The f unctions of the PenMount Control Panel are Device, Multiple Monitors ,Tools and About, which are explained in the following sections.

Devic e

Standard Calibration

Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press ‘ESC’.

Advanced Calibration

Advanced Calibration uses 4, 9, 16 or 25 points to effectivel y calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’.

In this window, you can find out that how many devices be detected on your s ystem.

Calibrate

This function offers two ways to c alibrate your touch screen. „Standard screens. „Advanced

Calibration? adjusts aging touch screens.

Calibration? adjusts most touch

Command C alibration Command call calibration function. Use

command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos

prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.exe

-c alibration 0 ( Standard Calibration) Dmcctrl.exe - calibration ($) 0= Standard Calibration 4=Advanc ed Calibration 4 9=Advanced Calibration 9 16=Advanced Calibration 16 25=Advanced Calibration 25

Step 1. Please s elec t a device then click “C onfigure”. You can also double click the device too.

Step 2.Click “Standard Calibration” to start calibration procedure

NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an

accurate calibration. Use a s tylus during Advanced Calibration for greater accuracy. Pleas e follow the step as below:

Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration.

Step 4. Select Device to calibrate, then you can start to do Advanced Calibration.

NOTE: Recommend to use a stylus during Advanced Ca libration for greater accuracy.

Setting

About

This panel displays inform ation about the PenMount controller and driver version .

Multiple Monitors

Multiple Monitors support f rom two to six touch screen displays f or one s ystem. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This f unction supports from two to six touch sc reen displays f or one system. Each monitor requires its own PenMount touch screen control board, either installed inside the dis play or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface. Driver installation procedures are the same as for a single monitor. Multiple Mon itors support the following modes:

Windows Extends Monitor Function Matrox DualHead Multi-Screen Function nVidia nView Function

NOTE: The Multiple Monitor function is for use with multiple displays only. Do not use this

function if you have only one touch sc reen display. Please note on ce you turn on this function the rotating function is disabled.

Enable the multiple display function as follows:

1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens to assign touch c ontrollers to displays.

2. When the mapping screen message appears, click OK.

3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens.

4. Touching all screens completes the mapping and the desktop reappears on the monitors.

5. Select a display and execute the “Calibration” function. A mes sage to start calibration appears. Click OK.

6. “Touch this screen to start its calibration” appears on one of the screens . Touch the screen.

7. “Touch the red square” messages appear. Touch the red squares in sequence.

8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.

NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the

Multiple Monitor f unction. Just follow the regular procedure for calibration on each

of your desktop monitors.

2. The Rotating f unction is disabled if you us e the Multiple Monitor function.

3. If you change the resolution of display or screen address, you have to redo Map

Touch Screens, so the system understands where the displays are.

Ab out

This panel displays information about the PenMount controller and this driver version.

PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of W indows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities.

PenMount Monitor has the following f unction

PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software pac kages such as:

• Portrait?s Pivot Screen Rotation Software

• ATI Display Driver Rotate Function

• nVidia Display Driver Rotate Function

• SMI D isplay Driver Rotate Function

• Intel 845G/GE Display Driver Rotate Func tion

Configuring the Rotate Function

1. Install the rotation software package.

2. Choose the rotate function (0°, 90°,

180°, 270°)

in the 3rd party software. The calibration screen

appears automatically. Touch this point and rotation is mapped.

NOTE: The Rotate function is disabled if you us e Monitor Mapping

5.2.2 Software Function s(Projected Capacitive)

General

In this window, you c an see there is USB Controller. Click OK to continue.

Monitor Mapping

to adjust touch panel

Add

to search for device

Setting

Beep

Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card

Linearization Style

9 points 25 points

Double Click Time

Shorter Longer

Double Click Area

Smaller Bigger

Normal mode

Simulate the mouse mode

Option

Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time

Tools Click OK to continue the settings.

4 Points Calibration

Do 4 points alignment to match display.

Clear and Calibrate

Clear linearization parameter and do 4 points alignment.

Linearization

Do 9 points linearization for better touchscreen linearity.

Draw Test

Do draw test to verify the touch accuracy.

Display In this window, it shows the mode of display.

Enable Multiple Monitors.

Map to main display if system has onl y one display monitor

Full Screen Lower Screen Lef t Screen Upper Screen Right Screen

Other

Other mode of display. Quarter1~4 and Customized area.

Active Area

Drag active area to enable Active Area Function.

Hardw are

Saturn Hardware Configuration

About

To display information about eGalaxTouch and its version.

Acnodes PC 9150 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual