Acnodes PC 8153 User Manual

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
1
PC 8153
15-inch touch panel PC
User Manual
PC 8153: 15-inch Pentium 4 1024x768 touch panel PC
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
2
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Disclaimers
This manual has been carefully checked and believed to contain accurate information. ACNODES Co. assumes no responsibility for any infringements of patents or any third party 's rights, and any liability arising from such use.
ACNODES does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. ACNODES does
not make any commitment to update the information in this manual. ACNODES reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of ACNODES Co.
Copyright 2008 ACNODES Co., Ltd. All Rights Reserved August 2008, Version A2
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
3
PC 8153
15-inch touch panel PC
Safety Approvals CE MarkingFCC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are meant to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that doesn't connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for help. Shielded interface cables must be used in order to comply with the emission limits.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
4
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Safety Precautions Before getting started, please read the following important safety precautions.
1. The PC 8153 Series does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static- shielded devices. Most electronic components are sensitive to static electrical charge.
3. Disconnect the power cord from the PC 8153 Series before any installation. Be sure both the system and external devices are turned OFF. A sudden surge of power could ruin sensitive components that the PC 8153 Series must be properly grounded.
4. The brightness of the flat panel display will be getting weaker as a result of frequent usage. However, the operating period varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not spray any liquid cleaner directly onto the screen. The PC 8153 Series may
come with or w/o a touch screen. Although the touch screen is chemical resistant, it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen. In case your
system comes without the touch screen, you must follow the same procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touch screen. Scratches on the touch screen may cause malfunction or internal failure to the touch screen.
7. The flat panel display is not susceptible to shock or vibration. When assembling the PC 8153 Series, make sure it is securely installed.
8. Do not open the system's back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
5
PC 8153
15-inch touch panel PC
Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
When handling boards and components, wear a wrist- grounding strap, available from most electronic component stores.
Trademarks Acknowledgments
ACNODES is a trademark of ACNODES Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
®Intel and Pentium® are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation. VIA is a trademark of VIA Technologies, Inc. SST is a trademark of Silicon Storage Technology, Inc. UMC is a trademark of United Microelectronics Corporation. Other brand names and trademarks are the properties and registered brands of their respective owners.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
6
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
C h a p t e r 1 Introduction
This chapter contains general information and detailed specifications of the PC 8153. Chapter 1 includes the following sections:
General Description System Specification Dimensions Front View & I/O Outlets Package List
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
7
PC 8153
15-inch touch panel PC
1.1 General Description
The PC 8153 is a 15" Industrial panel PC which features Intel® Core™ 2 Duo processor and Intel® Q965 chipset to provide powerful computing performance. This panel PC also offers the expansion ability with two PCI slots. It adopts built-in speaker and WLAN module for wireless connectivity. Further, the PC 8153 fits in with Aluminum IP65/NEMA4 compliant front bezel.
Powerful computing: Intel® Core™2 Duo processor The PC 8153 features Intel® Core™ 2 Duo with a maximum of FSB 1066 MHz and Intel® Q965+ICH8 chipset. It features
two 1394a ports, two gigabit Ethernet ports and up to 4GB of dual-channel DDR2 system memory which deliver high com­puting capability for high performance- demanding applications.
Expandable for 2 PCI slots The PC 8153 has two PCI slots for expansion purpose. User can easily plug in standard half-size PCI cards such as motion
card, communication card and so on. Speaker & WLAN antenna supported The PC 8153 features built-in speaker, optional WLAN module and antenna for wireless network connectivity. This ideal
industrial-grade panel computer PC 8153 can be applied to the several of industrial or commercial projects, such as trans­portation, factory automation, HMI machine controller, Point Of Sales, KIOSK and more. Moreover, PC 8153 provides highly reliable and highly flexible industrial-grade products in all-in-one solutions.
1.2 System Specifications
1.2.1 Main CPU Board
CPU Socket LGA775 for Intel® CoreTM 2 Duo/CoreTM Solo Processor with FSB 533/800/1066 MHz NOTE It doesn't support the processor with FSB 1333 MHz, and it is not recommended to use Quad-Core CPU. System Chipset
- Intel® Q965 + ICH8
BIOS
- Phoenix-Award BIOS, 16Mbit with RPL/PXE LAN Boot ROM, SmartView and Customer CMOS Backup
System Memory
- Two 240-pin DDR2 DIMM maximum up to 4GB
L2 Cache
- Integrated in CPU
Bus Clock
- 533/800/1066 MHz
Watchdog Timer
- Up to 255 levels as Reset feature
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
8
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
1.2.2 I/O System
Standard I/O
- Three serial ports with power, two RS-232 and one RS-232/422/485
- One PS/2 for Keyboard and Mouse Interface
- Four USB Ports 2.0 compliant
- Two IEEE1394a Ports
- One DVI-I Output
Ethernet
- First port with i82566DM Gigabit Ethernet PHY, Second port with RTL8111B for Gigabit/Fast Ethernet
Audio
- HD Audio for two channels output
- MIC-In, Line-Out
Storage
- Four SATA-300 interface
Box-Header
- One 26-pin for shared LPT/FDD(optional)
Expansion Slot
- Two 32-bit PCI Master slots
1.2.3 System Specification
15" TFT LCD Disk Drive Housing
- One built-in slim type CD-ROM dive,
- One internal 3.5" drive (Optional 2 X 3.5" or 2 X 2.5" HDD) AC Power Supply (100V ~ 240V) Heat Dispensing Design
- Two slots for PCI expansion Net Weight
- 13 Kgs Dimension (Main Body Size)
- 420mm (16.51")(W) x 150mm (9.14")(D) x 335mm (13.19")(H) Operation Temperature
- 0 to 40; Relative Humidity 50% Relative Humidity
- 10% to 85% @ 40?, Non-Condensing Vibration (Operating)
- 5 to 500 Hz, 1 G random Shock (Operating)
- 10 G peak acceleration (11 msec. duration)
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
9
PC 8153
15-inch touch panel PC
1.3 Dimensions
This diagram shows you dimensions and outlines of the PC8153.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
10
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
1.4 Front View and I/O Outlets
1.4.1 Front View
Please refer to the following illustration for features and controls of the PC 8153 front bezel.
1.4.2 I/O Outlets
The following figure shows the I/O locations of the PC 8153.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
11
PC 8153
15-inch touch panel PC
1.5 Package List
The package bundled with your PC 8153 should contain the following items:
PC 8153 x 1 AC power cord x 1 Panel mount kit x 7 Driver CDx1 LGA 775 CPU Cooler x 1 DVI TO VGA Adaptor x 1 PS/2 Splitter - Y Cable x 1 SATA Cable x 1 Dual 3.5" HDD bracket kit with fan x 1 (Optional) Small HDD Kit for 2.5" HDD (Optional) VIA WLAN Kit (Optional) If you can not find this package or any items are missing, please contact ACNODES distributors immediately.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
12
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
C h a p t e r 2 Hardware Installation The PC 8153 is convenient for your various hardware configurations in flexible ways, such as CPU (Central Processing Unit),
HDD (Hard Disk Drive), Memory Module (DRAM), CD-ROM, Add-On card, and more. The chapter 2 will show you how to install the hardware. It includes:
CPU DRAM Hard Disk CD-ROM Add-On Card Serial Port VGA Ethernet Mounting Ways
2.1 Installing the CPU and DRAM
The standard PC 8153 system is designed for Intel CoreTM 2 Duo processors. The built-in CPU board provides two 240-pin DDR2 DIMM sockets that support system memory up to 4GB.
Please refer to the instructions below, illustrated with concise images, to upgrade the CPU, DRAM, PCI step by step: Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
13
PC 8153
15-inch touch panel PC
Step 3 Install the CPU and DDR DRAM in the PC 8153
2.2 Installing the the Hard Disk Drive
The PC 8153 offers a convenient drive bay module for users to install HDD. The system offers users two 3.5" Hard Disk Drives for installation. If you want to install one or two 2.5" HDD, the PC 8153 also provides the 3.5" to 2.5" drive holder to meet your requirement. Please follow the steps:
Note The hardware limitation is the 2.5" HDD and 3.5" HDD CAN NOT exist simultaneously. Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit. Step 3 Unscrew 4 screws from the HDD drive bracket, and take out HDD bracket kit to install 3.5" HDD.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
14
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Step 4 The installation is completed. Installing Dual 3.5" HDD If installing the dual 3.5" HDD, please follow the steps: Step 1 Change HDD bracket from 3.5" to dual 3.5".
Step 2 Fix the Hard Disk to the HDD bracket to complete the installation.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
15
PC 8153
15-inch touch panel PC
Note When installing Dual 3.5" HDD, users must install a fan to decrease system heat. Installation step as following: Installing fan when using dual 3.5" HDD Step 1 Screw the fan to the right side of cover.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
16
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Step 2 Connect power cable of fan to 3 pin fan connector (CN3) in motherboard.
If installing the 2.5" HDD, please follow the steps: Step 1 Set the 2.5" HDD in the HDD bracket kit.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14 short depth server
17
PC 8153
15-inch touch panel PC
Step 2 Install the HDD in the PC 8153.
2.3 CD-ROM Installation
The PC 8153 offers a convenient drive bay module for users to install CD-ROM. When installing the CD-ROM, refer to the following instructions and illustration:
Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit. Step 3 Unscrew 3 screws which are around the chassis.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
18
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
2.4 Add-on Card Installation
The PC 8153 provides a riser card for PCI slots expansion. The riser card assembly can accommodate both half-size expan­sion cards. To install the riser card, refer to the following figure and instructions below:
Step 1 Remove the rear chassis. Setp 2 Remove the riser card fix kit. Step 3 Remove plates.
Step 4 Insert the add-on card in the socket firmly until it is completely seated.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
19
PC 8153
15-inch touch panel PC
2.5 Serial Port Interface
The PC 8153 has three onboard serial ports, COM1, COM2, and COM3. COM1 is RS-232(default)/422/485 Port Connector while COM2 and COM3 are RS-232 Port Connectors. The connector, COM1, COM2, COM3 are DB-9 connector, and the following table shows the pin assignments of this connector.
2.6 DVI-I
The PC 8153 has a DVI-Iinterface connector. It is able to connect to an expansion CRT monitor, and the system can display on both the flat panel and the CRT simultaneously.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
20
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
NOTE It doesn't support display in LCD and DVI-D simultaneously. DVI-D is only available after booting up in Windows XP.
2.7 Ethernet
The PC 8153 provides a NE2000 compatible Ethernet (RJ-45) interfaces. For network connection, just plug in one cable end of the system's 10/100/1000-Base-T Hub into a standard RJ-45 connector.
Please refer to detailed pin assignment list below:
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
21
PC 8153
15-inch touch panel PC
2.8 Mountings Way - Panel
There is one application option for the PC 8153, Panel mounting. Panel - Mount Kit Assembley The PC 8153 is designed for panel mount application. To mount the PC 8153, the standard set of mounting kit (included in
the system packaging) is needed.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
22
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
C h a p t e r 3 Phoenix-Award BIOS Utility The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured
parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off.
3.1 Entering Setup
There are two ways to enter the Setup program. You may either turn ON the computer and press <Del> immediately, or press the <Del> and/or <Ctrl>, <Alt>, and <Esc> keys simultaneously when the following message appears at the bottom of the screen during POST (Power on Self Test).
If the message disappears before you respond and you still want to enter Setup, please restart the system to try it again. Turning the system power OFF and ON, pressing the "RESET" button on the system case or simultaneously pressing <Ctrl>, <Alt>, and <Del> keys can restart the system. If you do not press keys at the right time and the system doesn't boot, an error message will pop out to prompt you the following information:
3.2 Control Keys
3.3 Getting Help
Main Menu The online description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press <F1> to pop out a small Help window that provides the description of using appropriate keys and possible selections for
highlighted items. Press <F1> or <Esc> to exit the Help Window.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
23
PC 8153
15-inch touch panel PC
3.4 The Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to configure then press <Enter> to accept or enter its sub-menu.
NOTE If your computer can not boot after making and saving system changes with Setup, the Award BIOS will reset your system to the CMOS default settings via its built-in override feature.
It is strongly recommended that you should avoid changing the chipset's defaults. Both Award and your system manufacturer have carefully set up these defaults that provide the best performance and reliability.
3.5 Standard CMOS Setup Menu
The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use <PgUp> or <PgDn> key to select the value you want in each item.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
24
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Date The date format is <day>, <date> <month> <year>. Press <F3> to show the calendar.
Time This item shows current time of your system with the format <hour><minute> <second>. The time is calculated based on the
24-hour military-time clock. For example, 1 p.m. is 13:00:00. IDE Primary Master/Primary Slave These items identify the types of each IDE channel installed in the computer. There are 45 predefined types (Type 1 to Type 45)
and 2 user's definable types (Type User) for Enhanced IDE BIOS. Press <PgUp>/<+> or <PgDn>/< > to select a numbered hard disk type, or directly type the number and press <Enter>. Please be noted your drive's specifications must match the drive table. The hard disk will not work properly if you enter improper information. If your hard disk drive type does not match or is not listed, you can use Type User to manually define your own drive type. If selecting Type User, you will be asked to enter related information in the following items. Directly key in the information and press <Enter>. This information should be provided in the documentation from your hard disk vendor or the system manufacturer.
If the HDD interface controller supports ESDI, select "Type 1". If the HDD interface controller supports SCSI, select "None". If the HDD interface controller supports CD-ROM, select "None".
If there is no hard disk drive installed, select NONE and press <Enter>. Video
Select the display adapter type for your system. Halt On
This item determines whether the system will halt or not, if an error is detected while powering up.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
25
PC 8153
15-inch touch panel PC
Press <Esc> to return to the Main Menu page.
3.6 Advanced BIOS Features
This section allows you to configure and improve your system, to set up some system features according to your preference.
CPU Feature Scroll to this item and press <Enter> to view the CPU Feature sub menu.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
26
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Hard Disk Boot Priority Scroll to this item and press <Enter> to view the sub menu to decide the disk boot priority.
Virus Warning This option flashes on the screen. During and after the system boot up, any attempt to write to the boot sector or partition table
of the hard disk drive will halt the system with the following message. You can run an anti-virus program to locate the problem. The default setting is "Disabled".
NOTE This function is only available with DOS and other operating systems that do not trap INT13.
CPU L1 & L2 Cache These two options speed up memory access. However, it depends on the CPU/chipset design. The default setting is "Enabled".
CPUs with no built-in internal cache will not provide the "CPU Internal Cache" item on the menu.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
27
PC 8153
15-inch touch panel PC
Quick Power On Self Test This option speeds up Power on Self Test (POST) after you turn on the system power. If set as Enabled, BIOS will shorten or
skip some check items during POST. The default setting is "Enabled".
First/Second/Third Boot Device These items let you select the 1st, 2nd, and 3rd devices that the system will search for during its boot-up sequence. The wide
range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM. Boot Other Device This item allows the user to enable/disable the boot device not listed on the First/Second/Third boot devices option above. The
default setting is "Enabled". Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive type, 40 or 80 tracks. 360Kb type is 40 tracks while 720Kb, 1.2MB and
1.44MB are all 80 tracks. The default value is "Enabled".
Boot Up NumLock Status Set the the Num Lock status when the system is powered on. The default value is "On".
Gate A20 Option The default value is "Fast".
Typematic Rate Setting This item determines the typematic rate of the keyboard. The default value is "Disabled".
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
28
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Typematic Rate (Chars/Sec) This option refers to character numbers typed per second by the keyboard. The default value is "6".
Typematic Delay (Msec) This option defines how many milliseconds must elapse before a held-down key begins generating repeat characters. The
default value is "250".
Security Option This item allows you to limit access to the system and Setup, or just to Setup. The default value is "Setup".
NOTE To disable the security, select PASSWORD SETTING at Main Menu and then you will be asked to enter a password. Do not type anything, just press <Enter> and it will disable the security. Once the security is disabled, the system will boot and you can enter Setup freely.
APIC Mode Use this item to enable or disable APIC (Advanced Programmable Interrupt Controller) mode that provides symmetric multi-
processing (SMP) for systems. MPS Version Control For OS This item specifies the version of the Multiprocessor Specification (MPS). Version 1.4 has extended configuration tables to
improve support for multiple PCI bus configurations and provide future expandability. Small Logo (EPA) Show If enabled, the EPA logo will appear during system booting up; if disabled, the EPA logo will not appear. Press <Esc> to return to the Main Menu page.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
29
PC 8153
15-inch touch panel PC
3.7 Advanced Chipset Features
This section contains completely optimized chipset 's features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware.
System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance.
However, if any program writes to this memory area, a system error may result. The default value is "Disabled". Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user
information of peripherals that need to use this area of system memory usually discusses their memory requirements. PCI Express Root Port Func Scroll to this item and press <Enter> to view the sub menu to decide the PCI Express Port.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
30
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Press <Esc> to return to the Advanced Chipset Featurs page. *** VGA Setting *** PEG/Onchip VGA Control Use this item to choose the primary display card. On-Chip Frame Buffer Size Use this item to set the VGA frame buffer size. DVMT Mode DVMT (Dynamic Video Memory Technology) helps you select the video mode. DVMT/Fixed Memory Size DVMT (Dynamic Video Memory Technology) allows you to select a maximum size of dynamic amount usage of the video
memory. The system would configure the video memory dependent on your application. Boot Display This item is for Intel define ADD card only. Press <Esc> to return to the Main Menu page.
3.8 Integrated Peripherals
This section allows you to configure your SuperIO Device, IDE Function and Onboard Device.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
31
PC 8153
15-inch touch panel PC
On-Chip IDE Device Scroll to this item and press <Enter> to view the sub menu On-Chip IDE Device.
IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports
block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support.
IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention. This improves data through-
put and frees CPU to perform other tasks. On-Chip Primary/Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate
each channel separately. The default value is "Enabled". NOTE Choosing Disabled for these options will automatically remove the IDE primary Master/Slave PIO and/or IDE Secondary IDE Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the
onboard IDE interface supports. Modes 0 to 4 provide successively increased performance. In Auto mode, the system automati­cally determines the best mode for each device.
IDE Master/Slave UDMA Select the mode of operation for the IDE drive. Ultra DMA-33/66/100/133 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver. If your hard drive and your system software both support Ultra DMA-33/66/100/133, select Auto to enable UDMA mode by BIOS.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
32
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
SATA Mode There are these options for you to set up SATA mode: IDE, RAID or AHCI. NOTE ICH8DO supports AHCI under Microsoft Windows VISTA and Microsoft Windows XP. ICH8 only supports AHCI under
Microsoft Windows VISTA. LEGACY Mode Support Legacy mode support allows devices to function in an operating environment that is not USB-aware. Press <Esc> to return to the Integrated Peripherals page. Super IO Device Scroll to this item and press <Enter> to view the sub menu Super IO Device.
Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you
install and-in FDC or the system has no floppy drive, select Disabled in this field. The options available are Enabled, Dis­abled.
Onboard Serial Port 1/2/3/4 Select an address and corresponding interrupt for the serial port. Options: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3,
Disabled, Auto. Serial Port 1/2/3/4 Use IRQ These items assign which I/O address to access onboard serial port 1/2/3/4. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. The options available are
378H/IRQ7, 278H/IRQ5, 3BC/IRQ7, Disabled. The 3BC option does not support any EPP modes.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
33
PC 8153
15-inch touch panel PC
Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port. Select Normal unless your hardware and software require one of the other modes offered in this field. The options available are EPP1.9, ECP, SPP, ECPEPP1.7, EPP1.7.
ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode. PWRON After PWR-Fail This item enables your computer to automatically restart or return to its operating status. Press <Esc> to return to the Integrated Peripherals page. Onboard Lan1/Lan2 Boot ROM Use this item to enable or disable the Boot ROM function of the onboard LAN1/LAN2 chips when the system boots up. USB Device Setting Scroll to this item and press <Enter> to view the sub menu USB Device Setting. USB (CN16) is not working when USB2.0
Controller is disabled.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
34
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
3.9 Power Management Setup
The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
35
PC 8153
15-inch touch panel PC
ACPI Function This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The function is always
"Enabled". ACPI Suspend Type This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as Windows
98SE, Windows ME and Windows 2000, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Options are:
[S1(POS)] The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system context.
[S3(STR)] The S3 sleep mode is a lower power state where the information of system configuration and open applications/ files is saved to main memory that remains powered while most other hardware components turn off to save energy. The information stored in memory will be used to restore the system when a "wake up" event occurs.
Run VGABIOS if S3 Resume When this item is set Auto, the system will run VGA BIOS if it is reaumed from the S3 state. Power Management This option allows you to select the type (or degree) of power saving for Doze, Standby, and Suspend modes. The table
below describes each power management mode:
Video Off Method This setting determines the manner in which the monitor is blanked.
Video Off In Suspend This item defines if the video is powered down when the system is put into suspend mode.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
36
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Video Off In Suspend This item defines if the video is powered down when the system is put into suspend mode. Suspend Type If this item is set to the default Stop Grant, the CPU will go into Idle Mode during power saving mode. Moden Use IRQ If you want an incoming call on a modem to automatically resume the system from a power saving mode, use this item to
specify the interrupt request line (IRQ) used by the modem. You might have to connect the fax/modem to the board Wake On Modem connector for working this feature.
Suspend Mode After the selected period of system inactivity (1 minute to 1 hour), all devices except the CPU shut off. The default value is
"Disabled".
HDD Power Down If HDD activity is not detected for the length of time specified in this field, the hard disk drive will be powered down while
all other devices remain active. Soft-Off by PWR-BTTN This option only works with systems using an ATX power supply. It also allows the user to define which type of soft power OFF
sequence the system will follow. The default value is "Instant-Off".
Wake-Up by PCI card If enable this item, the system can automatically resume when the PCI Modem or PCI LAN card receives an incoming call. Power On by Ring This option allows the system to resume or wake up upon detecting any ring signals coming from an installed modem. The
default value is "Enabled". Resume by Alarm If enable this item, the system can automatically resume after a fixed time in accordance with the system's RTC real time
clock.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
37
PC 8153
15-inch touch panel PC
** Reload Global Timer Events ** Global Timer (power management) events can prevent the system from entering a power saving mode or can awaken the
system from such a mode. Primary/Secondary IDE 0/1 Use this item to configure the IDE devices monitored by the system. FDD, COM, LPT Port Use this item to configure the FDD, COM and LPT ports monitored by the system. PCI PIRQ[A-D]# This item can be used to detect PCI device activities; if no activity, the system will enter the sleep mode. Press <Esc> to return to the Main Menu page.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
38
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
3.10 PnP/PCI Configuration Setup
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
Reset Configuration Data Normally, you leave this item Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit
Setup or if installing a new add-on cause the system reconfiguration a serious conflict that the operating system can not boot. Options: Enabled, Disabled.
Resources Controlled By The Award Plug and Play BIOS can automatically configure all boot and Plug and Play-compatible devices. If you select Auto,
all interrupt request (IRQ), DMA assignment, and Used DMA fields disappear, as the BIOS automatically assigns them. The default value is "Manual".
IRQ Resources When resources are controlled manually, assign each system interrupt to one of the following types in accordance with the
type of devices using the interrupt:
1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1).
2. PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture. The default value is "PCI/ISA PnP".
PCI/VGA Palette Snoop
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
39
PC 8153
15-inch touch panel PC
Some non-standard VGA display cards may not show colors properly. This item allows you to set whether MPEG ISA/VESA VGA Cards can work with PCI/VGA or not. When enabled, a PCI/VGA can work with a MPEG ISA/VESA VGA card; when disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.
** PCI Express relative items ** Maximum Payload Size When using DDR SDRAM and Buffer size selection, another consideration in designing a payload memory is the size of the
buffer for data storage. Maximum Payload Size defines the maximum TLP (Transaction Layer Packet) data payload size for the device.
Press <Esc> to return to the Main Menu page.
3.11 PC Health Status
This section supports hardware monitoring that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board.
Shutdown Temperature It helps you set the maximum temperature they system can reach before powering down.
Current SYSTEM Temperature Show you the current system temperature.
Current CPU Temperature These read-only fields show the functions of the hardware thermal sensor by CPU thermal diode that monitors the chip
blocks to ensure a stable system.
Vcore +3.3V/+5V/+12V/VBAT(V)/5VSB Show you the voltage of +3.3V/+5V/+12V. Press <Esc> to return to the Main Menu page.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
40
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
3.12 Frequency/Voltage Control
This section is to control the CPU frequency and Supply Voltage, DIMM OverVoltage and AGP voltage.
CPU Clock Ratio Use this item to select the CPU's frequency. Auto Detect PCI Clk The enabled item can automatically disable the clock source for a PCI slot without a module, to reduce EMI (Electro Magnetic
Interference). Spread Spectrum If spread spectrum is enabled, EMI (Electro Magnetic Interference) generated by the system can be significantly reduced.
Press <Esc> to return to the Main Menu page.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
41
PC 8153
15-inch touch panel PC
3.13 Load Optimized Defaults
This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. To load SETUP defaults value to CMOS SRAM, enter "Y". If not, enter "N".
3.14 Set Supervisor/User Password
You can set either supervisor or user password, or both of then. The differences between are:
1. Supervisor password: can enter and change the options of the setup menus.
2. User password: just can enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a pass-
word. ENTER PASSWORD: Type the password with eight characters at most, and press <Enter>. The password typed will now clear any previously entered
password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message will confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely.
PASSWORD DISABLEDÚ When a password is enabled, you have to type it every time you enter Setup. This prevents any unauthorized person from
changing your system configuration. Additionally when a password is enabled, you can also require the BIOS to request a password every time the system reboots.
This would prevent unauthorized use of your computer. You determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security
option is set to "System", the password is required during boot up and entry into Setup. If set as "Setup", prompting will only occur prior to entering Setup.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
42
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
3.15 Save & Exit Setup
This allows you to determine whether or not to accept the modifications. Typing "Y" quits the setup utility and saves all changes into the CMOS memory. Typing "N" brigs you back to Setup utility.
3.16 Exit Without Saving
Select this option to exit the Setup utility without saving the changes you have made in this session. Typing "Y" will quit the Setup utility without saving the modifications. Typing "N" will return you to Setup utility.
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
43
PC 8153
15-inch touch panel PC
C h a p t e r 4 Driver Installation
4.1 System PC 8153 supports Windows 2000/XP/Vista. To facilitate the installation of the system driver, please carefully read the instruc-
tions in this chapter before start installing.
1. Here is the path for the system driver: Panel series\PC 8153\Driver
2. Select all files, follow the installing procedure, and finally press OK.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
44
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
4.2 Touch Screen
4.2.1 Specification
4.2.2 Driver Installation - Windows 2000/XP/Vista
The PC 8153 provides a driver of the touch screen that users can install it under operating system Windows 2000/XP/Vista. To facilitate this touch screen driver installation, users should read the instructions in this chapter carefully before start the installa­tion.
1. Insert Driver CD and follow the path to select the "Panel series\PC 8153\Driver \Step5 - Touch\Driver\Windows 2000_XP_Vista Universal Driver\Setup.exe".
2. Follow the installing procedure and press OK.
3. Click Start menu and select "Pen mount Utilities", and then a "Pen mount Control Panel" pops out. Note Please choose COM4 for touch screen installation
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
© Copyright 2009 Acnodes, Inc . All right s reserved. Product descripti on and product specifi cations are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
14 short depth serverRMC 7152
14” short depth server
45
PC 8153
15-inch touch panel PC
4. Select the "Standard Calibrate" tab.
5. Calibration: To adjust the display with touch panel, click "Calibration" and follow the calibrate point to do calibration; there are five points on screen for calibration.
6. Press OK.
4.2.3 Driver Installation - DOS
Using "INSTALL.EXE" Utility to Install Pen Mount Software Driver
1. Insert Driver CD and select the Panel series\P1153-841\Driver\Step5 - Touch\Driver\DOS\Install.exe
2. Press ENTER key to install the drivers to drive C or use keyboard to key-in the hard disc drive that you plan to install the driver.
3. The driver will ask "Do you want to modify your Autoexec.bat to initialize Pen Mount? (Y/N)" Suggest you choose "YES" for generating the initialization instructions in AUTOEXEC.BAT files. Then follow up the instructions to complete the installation.
© Copyright 2009 Acnodes, Inc . All right s reserv ed. Prod uct descripti on and produ ct speci fi catio ns are subjec t to c hange witho ut notic e. For latest produ ct informat ion , please visi t Acnodes’ web sit e at www.a cnod es.c om.
PC 5150
15-inch touch panel PC
46
PC 8153
15-inch touch panel PC
661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218, www.acnodes.com
Identify the Communication Port and IRQ Number
1. For the first time installation, or changing Pen Mount Touch Screen's COM port, use PMDETECT (e.g. C:\PEN MOUNT\PMDETECT) to check the COM port and IRQ number. PMDETECT will save the correct data to PMOUSE.CFG file for further use.
2. The driver detects your communication COM port and IRQ number from COM1 IRQ4, COM2 IRQ3, COM3…. to COM4 IRQ15. Pen mount driver can find the COM port and IRQ number automatically. The screen will then show:
Pen Mount is initialized successfully!!! Create file "pmouse.cfg". Success. Pen Mount internal settings: Comm. Port: COM<n> IRQ<n>
3. PMDETECT program is able to skip the IRQ number detecting if the Touch screen Driver Installation 13 does not need to detect the specified IRQ number. For example, you do not need to detect IRQ5, and the command is: C:\PEN MOUNT\PMDETECT -N5
4. If you do not need to detect IRQ5 and IRQ9, the command is: C:\PEN MOUNT\PMDETECT -N5 -N9 Do Calibration
1. To adjust the touch screen mapping properly to display screen, use PM.BAT (C:\PEN MOUNT\PM) to do calibration. Choose "1" DO CALIBRATION (adjust screen mapping).
2. The message pops out to ask if you select the video mode number. Use keyboard to select starting the calibration, touch the upper- center point, then right-center point, bottom-center point and
left- center point in sequence. After the calibration is done, the data will be shown on the screen, then press any key to con­tinue the progress.
3. After the calibration, you are suggested to test the touch screen and display mapped results by choosing "3" DRAWING TEST under PM.BAT
Initializing the Pen mount Driver If you don't have the initialization commands in AUTOEXEC.BAT, initialize Pen mount C:\PEN MOUNT\PMINIT) controller before
you use the Pen mount Touch Screen. The display will show the initialization message: Pen mount V7.06 Copyright(c) SALT International Corp. Test:COM<n> IRQ<n> (<n> is the number after PMDETECT done) Pen mount communication settings: COM<N> IRQ<n> Baud Rate: <xxxx> Demonstration To demonstrate or test touch screen operation, please select "3" DRAWING TEST in PM.BAT file of the Utility Directory.
Drawing will be shown on the screen. The demonstration program "ICECREAM.EXE" in the "PEN MOUNT" directory can be applied, too.
Loading...