Acnodes PC 5173 User Manual

User Manual

PC 5173

17” Industrial wireless Panel PC

PC 5153: 15” Industrial Panel PC with Core 2 Quad/Duo processor PC 5173: 17” Industrial Panel PC with Core 2 Quad/Duo processor

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to improve reliability , design and function and does not represent a commitment on the part of the manufacturer .

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer .

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

T able of Contents

CHAPTER 1 INTRODUCTION

1.1 GENERAL OVERVIEW .................................................................................................... 2

1.1.1 MODEL V ARIA TIONS ........................................................................................ .2

1.1.2 APPLICA TIONS ...................................................................................................3

1.1.3 FEA TURES ......................................................................................................... 4

1.2 EXTERNAL OVERVIEW ...................................................................................................4

1.2.1 FRONT P ANEL ....................................................................................................5

1.2.2 REAR P ANEL ......................................................................................................6

1.2.3 TOP P ANEL .........................................................................................................6

1.2.4 BOTTOM P ANEL .................................................................................................7

1.2.5 LEFT P ANEL .......................................................................................................8

1.2.6 RIGHT P ANEL .....................................................................................................8

1.3 INTERNAL OVERVIEW .....................................................................................................9

CHAPTER 2 SPECIFICATIONS

2.1 INTRODUCTION .............................................................................................................. 10

2.1.1 SYSTEM SPECIFICA TIONS ............................................................................ 1 1

2.1.1.2 PC SERIES SPECIFICA TIONS .....................................................................14

2.2 DIMENSIONS................................................................................................................... 16

2.2.1 PC5153 Dimensions ......................................................................................... 17

2.2.2 PC5173 Dimensions ......................................................................................... 18

2.3 GRAPHICS SUPPORT..................................................................................................... 19

2.4 MEMORY .......................................................................................................................... 20

2.5 STORAGE ........................................................................................................................ 21

2.5.1 CompactFlash® ................................................................................................ 22

2.5.2 Hard Drive .......................................................................................................... 22

2.6 FRONT P ANEL ............................................................................................................... .. 23

2.6.1 FLA T SCREEN ....................................................................................................24

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

2.6.2 Touch Screen .................................................................................................... 24

2.7 POWER SUPPL Y ........................................................................................................... 25

2.7.1 AC INPUT/ DC INPUT SPECIFICA TIONS ......................................................25

2.8 EXP ANSION SLOTS....................................................................................................... 26

2.9 WIRELESS LAN (PC SERIES ONL Y) ........................................................................... 26

CHAPTER 3 UNPACKING

3.1 ANTI-ST ATIC PRECAUTIONS ........................................................................................ 29

3.2 UNP ACKING PRECAUTIONS ........................................................................................ 29

3.3 P ACKAGE CONTENTS .................................................................................................. 30

CHAPTER 4 INSTALLATION AND CONFIGURATION

4.1 INST ALLA TION PRECAUTIONS .................................................................................... 33

4.2 PREINST ALLED COMPONENTS................................................................................... 33

4.3 INST ALLA TION AND CONFIGURA TION STEPS .......................................................... 34

4.4 REMOVE THE BACK COVER ....................................................................................... 35

4.5 JUMPER SETTINGS ....................................................................................................... 36

4.5.1 Access the Jumpers .......................................................................................... 36

4.5.2 Preconfigured Jumpers .................................................................................... 37

4.5.3 CF Card Setup ................................................................................................. 37

4.5.4 COM1 to COM5 Pin 9 Select........................................................................... 38

4.5.5 COM5 RS-232/422/485 Serial Port Select Jumper ....................................... 39

4.5.5.1 COM 5 RS-422 and RS-485 Pinouts ................................................ 40

4.6 DRIVE INST ALLA TION ................................................................................................... 41

4.6.1 Hard Drive Installation....................................................................................... 41

4.6.2 CompactFlash® Installation.............................................................................. 43

4.6.3 CD Drive Installation ......................................................................................... 44

4.7 PCI EXP ANSION CARD INST ALLA TION (OPTIONAL) ................................................ 49

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

4.8 PCIE EXP ANSION CARD INST ALLA TION (OPTIONAL) ................................................ 51

4.9 A T/ATX MODE SELECTION ............................................................................................. 53

4.10 ACTIVA TING THE FRONT USB CONNECTORS (WIDS SERIES ONL Y) .................... 53

4.1 1 MOUNTING THE SYSTEM ............................................................................................... 55

4.1 1.1 WALL MOUNTING .............................................................................................. 55

CHAPTER 5 BIOS SETUP

5.1 INTRODUCTION.................................................................................................................. 67

5.1.1 Starting Setup ...................................................................................................... 67

5.1.2 Using Setup .......................................................................................................... 67

5.1.3 Getting Help .......................................................................................................... 68

5.1.4 Unable to Reboot after Configuration Changes ................................................. 68

5.1.5 BIOS Menu Bar .................................................................................................... 68

5.2 MAIN.................................................................................................................................... 69

5.3 ADV ANCED ...................................................................................................................... 70

5.3.1 CPU Configuration .............................................................................................. 71

5.3.2 IDE Configuration ................................................................................................ 72

5.3.2.1 IDE Master , IDE Slave .......................................................................... 74

5.3.3 Super IO Configuration ....................................................................................... 77

5.3.4 Hardware Health Configuration .......................................................................... 83

5.3.5 Power Configuration ........................................................................................... 86

5.3.5.1 ACPI Settings......................................................................................... 87

5.3.5.2 APM Configuration................................................................................. 87

5.3.6 Remote Access Configuration ........................................................................... 90

5.3.7 USB Configuration............................................................................................... 93

5.4 PCI/PNP .................................................................................................................... .......... 95

5.5 BOOT ................................................................................................................................... 97

. 5.5.1 Boot Settings Configuration................................................................................. 98

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

5.6 SECURITY ...................................................................................................................... 100

5.7 CHIPSET ........................................................................................................................ 101

5.7.1 North Bridge Configuration.............................................................................. 102

5.7.1.1 Video Function Configuration ........................................................... 103

5.7.2 South Bridge Configuration ............................................................................ 104

5.8 EXIT ................................................................................................................................ 105

CHAPTER 6 SYSTEM MAINTENANCE

6.1 SYSTEM MAINTENANCE INTRODUCTION ................................................................ 108

6.2 MOTHERBOARD REPLACEMENT ............................................................................. 108

6.3 BACK COVER REMOV AL ............................................................................................ 108

6.4 DIMM REPLACEMENT ................................................................................................. 109

6.5 ELEV A TED PLA TFORM REMOVAL .............................................................................110

6.6 PSU MODULE REPLACEMENT ...................................................................................1 12

6.6.1 Remove the Old PSU.........................................................................................1 12

6.6.2 Install the New PSU ...........................................................................................1 14

6.7 SYSTEM COOLING F AN REPLACEMENT ....................................................................115

6.7.1 Remove the Old System Cooling Fans ............................................................1 15

6.7.2 Install the New System Cooling Fans ...............................................................1 16

A. BIOS OPTIONS B. DIGITAL I/O INTERFACE

B.1 INTRODUCTION ............................................................................................................ 126

B.2 DIO CONNECTOR PINOUTS ....................................................................................... 126

B.3 ASSEMBLY LANGUAGE SAMPLES ........................................................................... 127

B.3.1 Enable the DIO Input Function..................................................................................... 127

B.3.2 Enable the DIO Output Function ................................................................................. 127

C. WATCHDOG TIMER

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

D. HAZARDOUS MATERIALS DISCLOSURE

D.1 HAZARDOUS MA TERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ......................................152

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

CHAPTER 1 INTRODUCTION

1. 1 OVERVIEW

The PC5153/ PC5173 flat panel PC is for industrial environments like production lines and machine automation. The PC5153/ PC5173 provides all the features of a PC, combined with a touch panel screen for mouse and keyboard free data input. The PC5153/ PC5173 provides wired networking for integration into company networks and PC5153/ PC5173 also provides wireless network via PIF A antenna on the front panel. All major external device connections including USB, serial and parallel port connectors. Storage options include a

2.5" hard drive and a CompactFlash® slot, allowing for flexibility in choosing solid state drives or traditional hard drives. A VGA output on the rear panel allows the PC5153/ PC5173 to connect to a second screen for duplicating the screen contents or extending the user interface.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

1.1.1 MODEL VARIATIONS

15” PC 5153 CPU: 2.2GHz Intel Celeron E1500 Power: AC input, 18~36V DC input 17” PC 5173 CPU: 2.2GHz Intel Celeron E1500 Power: AC input, 18~36V DC input

1.1.2 APPLICATIONS

PC 5173

17” Industrial wireless Panel PC

The PC5153/ PC5173 flat panel PC is designed for rigorous industrial environments where it may be exposed to both heat and moisture. Its durability and strength also makes it an ideal choice for public access computers. Some possible applications include:

ƒ Automated manufacturing processes ƒ Public information gathering point ƒ Plant environment monitoring system ƒ Factory automation ƒ Manufacturing shop flow ƒ Equipment and device control

1.1.3 FEATURES

Some of the features of the PC5153/ PC5173 flat panel PC include: ƒ Mainstream panel PC design with dual display function. ƒ Aluminum die-casting front panel meet IP 65 water proof standard ƒ Support LGA755 Intel® Core™2 Extreme/Quad/Duo, Celeron® processors with 800/1066/

1333 MHz FSB

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

ƒ Dual DDR3 memory DIMM (system max. 4 GB SDRAM) ƒ SA T A connectors ƒ High brightness industrial grade LCD panel ƒ The following I/O ports

o Five COM (one RS-232/422/485) o One CompactFlash® slot o One VGA port o One Parallel port

o USB 2.0 ports ƒ Dual 10/100/Gigabit Ethernet supported ƒ RoHS compliant

1.2 EXTERNAL OVERVIEW

The PC5153/ PC5173 flat panel PC is comprised of an LCD screen, aluminum front panel and heavy duty steel rear and side panels. The rear panel provides screw holes for wall and an arm mounting. The right panel provides access to a slim type CD drive bay . The bottom p anel provides access to external interface connectors that include GbE, USB 2.0, audio, parallel port, serial port connectors, VGA port and a CompactFlash® card slot.

1.2.1 FRONT PANEL

The front panel of the PC5153/ PC5173 (Figure 1-2) is a flat panel TFT LCD screen surrounded by an aluminum frame. The PC5153/ PC5173 also has wireless antenna and two USB ports protected by waterproof cover on the front panel.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

1.2.2REAR PANEL

The rear panel has a fan vent, four VESA standard mounting holes and several retention screw holes. The VESA mounting holes are circled in Figure 1-4.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

1.2.3 TOP PANEL

The top panel has three sets of mounting clamp slot, fan vents and retention screws for securing the drive bay bracket. The retention screws are circled in Figure 1-5 below.

1.2.4 BOTTOM PANEL

The bottom panel shown in Figure 1-6 has the following interfaces: ƒ 1 x Power input connector ƒ 1 x Power switch ƒ 4 x USB connectors ƒ 1 x Reset button ƒ 2 x RJ-45 GbE connectors ƒ 1 x PS/2 mouse connector ƒ 1 x PS/2 keyboard connector ƒ 4 x RS-232 connectors (COM1, COM2, COM3 and COM4) ƒ 1 x RS-232/422/485 connector (COM5) ƒ 1 x PCI/PCIe x1 add-on card slot ƒ 1 x Parallel port connector

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

ƒ 3 x Audio jacks ƒ 1 x VGA connector ƒ 1 x CompactFlash® slot ƒ 1 x AT/ATX switch ƒ 1 x USB switch

PC 5173

17” Industrial wireless Panel PC

1.2.5 LEFT PANEL

The left side panel hosts three cooling fans that cool the interior of the system (Figure 1-7).

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

1.2.6 RIGHT PANEL

The right panel has a CD-ROM drive bay for CD-ROM drive installation (Figure 1-8).

1.3 INTERNAL OVERVIEW

The PC5153/ PC5173 internal components are configured in three levels. The PSU cover bracket to the left (Figure 1-9) supports the hard drive and optical drive brackets. Below the PSU cover bracket is the power supply. On the same level as the power supply is the motherboard. Below the motherboard and PSU level is an LCD panel. An overview picture of the internal components is shown in Figure 1-9 below.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

CHAPTER 2 SPECIFICA TIONS

2.1 INTRODUCTION

The PC5153/ PC5173 flat panel PC has the following preinstalled components: ƒ 1 x Motherboard ƒ 1 x TFT LCD screen ƒ 1 x Power supply ƒ 2 x Cooling fans The technical specifications for these components and the system are shown in the sections

below.

2.1.1 SYSTEM SPECIFICATIONS

PC5153 PC5173 LCD Specs.Size 15" 17”

Resolution 1024 x 768 (XGA) 1280 x1024 (SXGA) Brightness 350 cd/m2 380 cd/m2 Contrast Ratio 700:1 1000:1 Pixel Pitch (mm) 0.297 x 0.297 0.264 x 0.264 Viewing Angle (V-H) 125/140 160/ 170 LCD Color 16.2M 16.7M Backlight MTBF 50,000 hours 50,000 hours

CPU:

2.66GHz Intel® Core™2 Quad Q9400 or 2.20GHz Intel® Celeron® dual-core E1500 CPU Socket: LGA775 Front Side Bus: 800 MHz, 1066 MHz or 1333 MHz Northbridge Chipset: Intel® G41 Southbridge Chipset: Intel® ICH7

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

Memory: Two 2.0 GB 800/1066 MHz DDR3 SDRAM DIMM (system max. 4.0 GB) Solid State Drive (SSD): One CompactFlash® Type II socket Drive Bay: One 2.5" SATA 3Gb/s or IDE anti-shock drive bay, One slim type CD-ROM bay Ethernet: Two PCIe GbE controllers Audio: RealTek ALC888 HD audio codec I/O ports: 1 x RS-232/422/485 2 x LAN connectors 4 x RS-232 3 x Audio connectors (line-in, line-out and mic-in) 6 x USB 2.0 (two on front panel are waterproof) 1 x CMOS reset button 2 x PS/2 for keyboard and mouse 1 x AT/ATX switch 1 x Parallel port connector 1 x USB switch 1 x VGA-out connector 1 x Power switch Wireless:

802.11 b/g/n wireless PCIe Mini module, Wireless antenna embedded in front panel Touch Screen: Resistive Type 5-wire (touch controller IC is on board) Mounting: VESA 100 mm x 100 mm (panel, wall, rack, stand and arm)

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

Expansion Slots: Optional riser card: One PCI slot or One PCIe x4 with PCIe x1 signal Chassis Construction: Heavy-duty steel Front Panel Construction: Aluminum Operating Temperature: -10ºC ~ 50ºC Storage Temperature: -20ºC ~ 60ºC Vibration: 5 Hz ~ 17 Hz 0.1" double amplitude displacement

17 Hz ~ 640 Hz 1.5G acceleration peak-to-peak Shock: 10G acceleration peak-to-peak (11 ms) Net/Gross Weight: 7 kg/11 kg 8 kg/12 kg Dimensions (W x H x D): 410 x 309 x 110.5 452 x 356 x 115 Power Supply: AC Input ATX (A Model) ƒ 220 W ƒ Input: 90 V AC~264 V AC, 50/60 Hz ƒ Output(max.): 3.3 A@14 A, 5 V@16 A, 12 V@10 A, -12 V@0.8 A DC Input ATX (AD Model) ƒ 200 W ƒ Input: 24 V DC (18~36 V DC), 50/60 Hz ƒ -Output(max.): 3.3 A@12 A, 5 V@12 A, 12 V@15.4 A, -12 V@0.5 A

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

2.2 DIMENSION

The dimensions of the PC5153/ PC5173 are shown in the sections below.

2.2.1 PC5153 DIMENSIONS

The dimensions of the PC5153 flat panel PC are shown below.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

2.2.2 PC5173 DIMENSIONS

The dimensions of the PC5173 flat panel PC are shown below.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

2.3 GRAPHICS SUPPORT

The Intel® G41 chipset has an integrated graphics engine, Intel® Graphics Media Accelerator X4500 that supports analog CRT display devices. The VGA port on the external peripheral interface connector panel connects a peripheral monitor to the PC5153/ PC5173 system.

2.4 MEMORY

All processors supported by the PC5153/ PC5173 have their own internal DDR3 memory controller. The DDR3 controller has the following features:

ƒ Low-latency, high-bandwidth ƒ Supports two 800 MHz, 1066 MHz or 1333 MHz DDR3 DIMMs ƒ Each DIMM has a maximum capacity of 2.0 GB The DDR3 controller on the processor is interfaced to two DIMM sockets on

the PC5153/ PC5173.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

2.5 STORAGE

There following storage options are available: CompactFlash® SATA hard drive

2.5.1 COMPACTFLASH

The CompactFlash® socket supports standard CompactFlash® Type II cards. The chipset flash interface is multiplexed with an IDE interface and can be connected to an array of industry standard NAND Flash or NOR Flash devices. The CompactFlash® slot location is shown below.

2.5.2 HARD DRIVE

The PC5153/ PC5173 comes has a single drive bay for 2.5" SATA 3Gb/s hard drive or IDE hard drive.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

2.6 FRONT PANEL

The front panel of the PC5153/ PC5173 consists of an LCD monitor and a touch screen panel.

2.6.1 FLAT SCREEN

The PC5153/ PC5173 comes with a TFT LCD monitor. The tough construction of the TFT monitor allows the PC5153/ PC5173 to withstand the conditions it is likely to be exposed to during regular use. Some of the specifications of the TFT monitors are shown below:

ƒ Pixel pitch of 0.297 mm or less ƒ 700:1 contrast ratio or better ƒ 350 cd/m2 or greater ƒ 0oC to 50oC operating temperature

2.6.2 TOUCH SCREEN

The touch screen panel on the PC5153/ PC5173 allows complete user interaction without the need for a keyboard or mouse. Some of the features of the touch panel are listed below. ƒ 5-wire analog resistive type ƒ 78% transmission ƒ Control chipset built onto the motherboard ƒ -10oC to 50oC operating temperature ƒ 7 V maximum voltage

2.7 POWER SUPPLY

The PC5153/ PC5173 flat panel PC comes with either an AC input 220 W AC 1U, or DC input 200 W DC 1U RoHS compliant ATX power supply. The PSUs have an MTBF greater than 100,000 hours.

W ARNING:

Under no circumstances is the PSU case to be opened. The PSU module is not user serviceable and there are dangerous high-voltages inside the case. If there are any problems with the PSU module, please contact the dealer or reseller immediately.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

2.7.1.1 AC INPUT/ DC INPUT SPECIFICATIONS

There are three connector for two kinds of expansion modules, Type A module and Type B module. Slot 1 and Slot 2 are for installing Type A module and Slot 3 is for Type B module. The pinouts of these slots are listed below.

2.8 EXPANSION SLOTS

The riser card with either a PCI or PCIe x1 expansion card slot can be separately purchased and installed in the PC5153/ PC5173. The expansion card slots add additional functionality to the PC5153/ PC5173.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

2.9 WIRELESS LAN

The PC5153/ PC5173 panel PC preinstalled an 802.11 b/g/n wireless LAN (WLAN) module in the Mini-PCIe socket and interfaced to the Intel® ICH7 through the PCIe x1 bus.

The wireless module is then connected directly to the front panel PIFA antenna.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

CHAPTER 3 UNPACKING

3.1 ANTI-STATIC PRECAUTIONS

WARNING! Failure to take ESD precautions during the installation of the PC5153/ PC5173 may result in permanent damage to the PC5153/ PC5173 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PC5153/ PC5173. Dry climates are especially susceptible to ESD. It is critical that the following anti-static precautions are strictly adhered to whenever handling the PC5153/ PC5173 or any other electrical component. ƒ Wear an anti-static wristband - Wearing a simple anti-static wristband can help to

prevent ESD from damaging the PC5153/ PC5173. ƒ Self-grounding - Touch a grounded conducting material before handling and peri

odically while handling the PC5153/ PC5173. ƒ Use an anti-static pad - When configuring the PC5153/ PC5173, place it on an

antic-static pad to reduce the possibility of ESD damage. ƒ Only handle the edges of the PC5153/ PC5173 - When handling the PC5153/

PC5173, hold it by its edges.

3.2 UNPACKING PRECAUTIONS

When the PC5153/ PC5173 is unpacked, please do the following: ƒ Follow the anti-static precautions outlined in Section 3.1. ƒ Make sure the packing box is facing upwards so the PC5153/ PC5173 does not

fall out of the box. ƒ Make sure all the components shown in Section 3.3 are present.

3.3 PACKAGE CONTENTS

1 x PC5153/ PC5173 1 x SATA CD-ROM cable 1 x Panel Mount Kit 1 x Wall Mount Kit 1 x Power cord 1 x Screw set

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

CHAPTER 4 INSTALLATION AND CONFIGURATION

4.1 INSTALLATION PRECAUTIONS

When installing the PC5153/ PC5173, please follow the precautions listed below: ƒ Turn power off: When installing the PC5153/ PC5173 make sure the power is off.

Failing to turn off the power may cause severe injury to the body and/or damage to the system.

ƒ Certified Engineers: Only certified engineers should install and modify on-board

functions.

ƒ Mounting: The PC5153/ PC5173 is a heavy device. When mounting the system

onto a rack, panel, wall or arm please make sure that at least two people are as sisting with the procedure.

ƒ Anti-static Discharge: If a user open the rear panel of the PC5153/ PC5173, to

configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband.

4.2 PREINSTALLED COMPONENTS

The following components are all preinstalled. ƒ Motherboard ƒ TFT LCD ƒ Touch screen ƒ Power switch ƒ Power supply ƒ Inverter board ƒ DIMM ƒ System cooling fans

Preinstalled OEM customizations may include the following. ƒ CPU ƒ HDD ƒ CD drive ƒ PCI/PCIe x4 riser card

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

Removal and reinstallation of some of the components are described in Chapter 4.

4.3 INSTALLATION AND CONFIGURATION STEPS

The following installation steps must be followed. Step 1: Unpack the PC5153/ PC5173.

Step 2: Set the jumper settings. Step 3: Install HDD, CompactFlash® and CD drive. Step 4: Mount the PC5153/ PC5173 flat panel PC. Step 5: Connect peripheral devices to the bottom panel of the PC5153/ PC5173. Step 6: Configure the system.

4.4 REMOVE THE BACK COVER

Remove all the retention screws on the back cover. Lift the cover up to remove (Figure 4-1).

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

4.5 JUMPER SETTINGS

NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.

The following jumpers can be found on the motherboard installed in the PC5153/ PC5173. Before thePC5153/ PC5173 is installed, the jumpers must be set in accordance with the desired configuration. The jumpers on the PC5153/ PC5173 motherboard are listed in Table 4-1.

4.5.1 ACCESS THE JUMPER

To access the jumpers, remove the back panel. To remove the back panel, please refer to Section 4.4.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

PC 5173

17” Industrial wireless Panel PC

4.5.2 PRECONFIGURED JUMPERS

WARNING: Do not change the settings on the jumpers in described here. Doing so may disable or damage the system

The following jumpers are preconfigured for the PC5153/ PC5173. Users should no change these jumpers.

4.5.3 CF CARD SETUP

Jumper Label: JCF1 Jumper Type: 2-pin header Jumper Settings:See Table 4-3 Jumper Location: See Figure 4-2 The CF Card Setup jumper sets the CF Type I card or CF Type II cards as either the

slave device or the master device. CF Card Setup jumper settings are shown in Table 4-3.

The CF Card Setup jumper location is shown in Figure 4-2.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

PC 5173

17” Industrial wireless Panel PC

4.5.4 COM1 TO COM5 PIN 9 SELECT

Jumper Label: J_COM_V1, J_COM_V2, J_COM_V3, J_COM_V4 and J_COM_V5 Jumper Type: 6-pin header Jumper Settings:See Table 4-4 Jumper Location: See Figure 4-3 Four jumpers configure pin 9 on the COM1, COM2, COM3 COM4 and COM5 connec-

tors. Pin 9 on these connectors can be set as either +5 V, +12 V or as the ring (RI) signal. The COM1, COM2, COM3, COM4 and COM5 Pin 9 Setting jumper selection options are shown in Table 4-4.

661 Brea Canyon Rd., Suite 3 Walnut, CA 91789 tel: 909.598.7388, fax: 909.598.0218

© Copyright 2011 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.

Acnodes PC 5173 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual