ACME LED-737 20130727113636.pdf

Download

Page 1

We declare that our products (lighting equipments) comply with the following

specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

EC - Declaration of Conformity

EN61000-4-11: 1994.

Harmonized Standard

Part 1: General requirements

User Manual

MARVELED

LED-737

Innovation, Quality, Performance

11C

Please read the instructions carefully before use

Page 2

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specif ications

3. Main Function

4. How to control the fixture

5. DMX 512 Configuration

6. DMX 512 Connections

7. Troubleshooting

8. Fixture Cleaning

The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.

y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

10C

Page 3

7. Troubleshooting

Following are a few common problems that may occur during operation. Here ar e some suggestions for easy troubleshooting:

A. The fixture does not work, no light and the fan does not work

1. Check the con nection of power and main fuse.

2. Measur e the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. You may have a break in the DMX cabling . Check the LED for the response of the master/ slave mode signal.

2. Wrong DMX address in the fixture. Set the proper address.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microph one to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. T he stepper motor might be damaged or the cable connected to the PCB is broken.

2. T he motor’s drive IC on the PCB might be out of condition.

1. Safety Introductions

Please read the instructions carefully which includes important

WARNING

y Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

y Unpack and check carefully there is no transportation damage before using the fixture. y Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the fixture.

y It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

y Disconnect main power before servicing and maintenance. y Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

y In the event of serious operating probl em, stop using the fixture immediatel y. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

y Do not connect the device to any dimmer pack. y Do not touch any wire during operation and there might be a hazard of electric shock. y To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

y The housing must be replaced if they are visibly damaged. y Do not look directly at the LED light beam while the fixture is on. y There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service, please contact your nearest dealer.

y Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage unit.

For power supply, do not connect in series much more than 33 units, use another mains supply for next 33 units.

information about the installation, operation and maintenance.

Page 4

2. Technical Specifications

y It can be operated by DMX512 co ntrol or can be used as an individual unit without

controller.

y It can be linked together as many as required in master/sl ave mode, and perform the

great built-in programmed lighting shows triggered by music.

y Please use a 3 pin XLR cable/plug when connecting them together. y It features different pre-programmed chase patterns. y Fan cooled. y Channels

Channel 1 = Mode Channel 2 = Pattern/Chase Channel 3 = Pattern Strobe/Chase Speed Channel 4 = Dimmer

y Power supply

Input Voltage：100V-240V~50-60Hz Power consumption：18W

y LED

Total 156pcs, Red 48pcs, Green 36pcs, Blue 36pcs, White 36pcs

y Dimension： 300 x 308 x 280mm y Weight： 4.2KG

3. Main Function

To select any functions, press MENU button until the req uired one is shown on the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to change the mode. Once the required mode has been selected, press ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds. Back to the functions without any change press MENU button. The main functions are shown below:

6. DMX512 Connections

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system

2. The DMX output and input connectors are pass-through to maintain the DMX circuit The DMX output and input connectors are pass-through to maintain the DMX circuit when one of the units’ power is disconnected.

3. At last fixture, the DMX cable has to be termi nated with a terminator to reduce signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and p in 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.

4. Each lighting fixture needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usual ly 0 & 1 are equal to 1).

5. 3 pin XLR connectors are more popular than 5 pins XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),

Pin4/5: Not used.

Page 5

the display stops blinking or storing automatically 8 seconds later. To go back to the functions without any change press the MENU button again. If you use please refer to the following diagram to address your DMX512 channel for the first 4 units.

5. DMX512 Configuration

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address has been selected, press ENTER button to setup or automatically retur n to the main functions without any change after 10 seconds. Back to the previous functions without any change press MENU button.

Master Mode

Press the MENU button up to when the button, Use DOWN and UP button to select the , Pressing ENTER button, Use

DOWN and UP button to select the or . Select the Pressing ENTER button, Use DOWN and UP button to select the or . Select the

Pressing ENTER button. Use DOWN and UP button to select the Yes or No

Blackout, Back to the main functions, press the MENU button twice.

Press the MENU button up to when the button, Use DOWN and UP button to select the

Back to the previous functions without any change press MENU button.

Slave Mode

is shown on the display. Pressing ENTER

or (Slave Mode 1and 2).

Page 6

LED

Press the MENU button up to when the is sho wn on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (ON) or (OFF) mode. Once the mode has been selected, press ENTER button to setup or automaticall y return to the main functions without any change after 10 seconds. Back to the functions without any change press MENU button again.

Display Inverse

Press MENU button until the mode has been selected, press ENTER button to setup or automatically return to the main functions without any change after 10 seconds. Back to the functions without any change press MENU button again.

Fixture Hours

Press the MENU button up to when the button and the display will show the number of working hou rs of the unit. To go back to the

functions press the MENU button again.

Software version

Press the MENU button up to when the is blinking on the display. Pressing ENTER button and the display will show the version of software of the unit. To go back to the

functions press the MENU button again.

is blinking on the display. Pressing ENTER button. Once

is blinking on the display . Pressing ENTER

4. How To Control The Unit

You can operate the unit in three ways:

1. Master/slav e built-in preprogram function

2. Easy controller

3. DMX controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be effected at once. Every time you turn the unit on, it will show the type on the display and move all the motors to their ‘home’ position and you may hear some noises for about 20 seconds. After that the unit will be ready to receive DMX signal or run the b uilt in programs.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the ot her units to give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode

(show 1) or (show 2) or (show 3) or (show 4) mode. Its

DMX input jack will have nothing plugged into it, and Its master LED will be constantly on and sound LED will flash to the music. The other units will have to set in slave mode

and select the DMX input jacks (daisy chain) and the slave led lights will constantly on.

2-light show

In 2-light show. In order to create a great light show , you can set

get contrast movement to each other, even if you have two units only.

(normal) or (2 light show) mode, Their DMX cables plugged into

(slave mode), means the unit works normally and means

on the second unit to

and select

4.2. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. There is a terminator for connect the easy controller inside the fixture. By connecting the cable into DMX IN waterproof cable entry gland to the CA-8 terminator of the first fixture, you will find that the remote control on the first fixture will control all the other fixtures for Stand by, Function and Mode functions.

Blackout Blackout the unit

Function

Mode

1. Synchronous Strobe

2. Sound Strobe

3. Two light Strobe Sound/Strobe

(LED OFF)

Chase Select (Chase 1-10)

Chase (LED ON)

4.3 DMX Controller

Use universal DMX controller to control the units, you have to set DMX addr ess from 1 to 512 channel so that the units can receive DMX signal.

Press the MENU button up to when the button and the display will blink. Use DOWN and UP button to change the DMX512 address.

Once the address has been selected, press and keep ENTER button pressed up to when

is showing on the display. Pressing ENTER