In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
Diagram for lamp changing
Because of its high internal pressure, there might be a
risk t hat t he Discharge lamp would explode during
operation. The lam p emits intense UV radiation which
is harmful to the eyes and skin. The high luminance of
the arc can cause severe damage to the retina if looks
directly at t he lamp.
1. Always switch off the main supply and never handle
the lamp or lum inaries when is hot.
2. Do not t ouch t he bulb with bare hands. If t his
happens, clean the lam p with denatured alcohol and
wipe it with a lint f ree cloth before installation.
3. The lamp generates UV radiation. Never operate the
lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and
IR-7S/7B/5C ( IR-5C is a 5 channel color changer )
MSD 250/2
CDM 150W
8F
there is a slight risk of arc tube rupture. The risk
increases with age, temperature and improper
handling of the lamp. Do not use the lamp any
longer than its specified life.
Make sure the lamp is located in the center of the
reflector for the best spot.
ELC 24V 250W
ELC 24V 250W
65. 4 DMX512 Configuration
Model CH1 CH2 CH3 CH4 CH5 CH6 CH7
IR-7S Pan Tilt
IR-7B Pan
IR-6SD/6S Pan Tilt
IR-6BD/6B Pan
IR-5S Pan Tilt
IR-5B Pan
IR-5C
IR-4C
IS-6S Pan Tilt
IS-6B Pan
IS-4
IS-3
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Barrel
Rotation
Barrel
Rotation
Barrel
Rotation
Gobo Color
Gobo Color
Barrel
Rotation
Gobo Color Reflector
Gobo
/Color
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
Shutter
/Shaking
No
Function
Gobo Color
Gobo Color
Gobo Color
Gobo Color
Gobo Color
Gobo Color
Gobo
Rotation
No
Function
Gobo Color Reflector
Gobo Color Reflector
Reflector
Dimmer
Dimmer
Gobo
Rotation
Gobo
Rotation
No
Function
No
Function
Dimmer
Dimmer
Dimmer
Dimmer
4. How To Set The Unit
4.1 Control Panel
Display
To show the various menu and the selected functions.
LED
DMX On DMX input present
MASTER On Master Mode
9F
SLAVE On Slave Mode
SOUND Flashing Sound activation
Button
MENU to select the programming functions
DOWN to go backward in the selected functions
UP to go forward in the selected functions
ENTER to confirm the selected functions
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and Mode.
Sensitivity
To adjust the sound sensitivity.
Microphone
To receives audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
4.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are showing below:
DMX512 Address Setting
Slave mode " Normal "
Slave mode " 2 Light Show "
Slave mode " 3 Light Show "
Slave mode " 4 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
MENU
and
DMX512 Address Setting
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
Slave Mode
Pan Inversion
Tilt / Barrel Normal
Tilt / Barrel Inversion
Dimmer Normal
Dimmer Inversion
LED on
LED off
Display Normal
Display Inversion
Focus Adjust
Self-Test
Fixture Hours
Reset
only for color-change
5.3.1 iSolution Operation
¤ Consistent DMX configuration enable iRock and iShow to be linked together and
controlled at the same time.
¤ DMX address can be set remotely by iLead controller ( please refer to the user manual
of iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
¤ Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from 1 to 512
channel so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when the
display stops blinking or storing automatically 8 seconds later. To go back to the functions
without any change press the MENU button again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
DMX address can be set remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
10F
( Following DMX address setting is based on that all the lighting fixtures are linked together
controlled by the 8-channel iLead IL-0824 controller. )
The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit, you will find
that the remote control on the first unit will control all the other units
as below.
Built-in lighting shows triggered by Easy Controller:
Stand by Blackout t he unit
IR-7S
IR-7B
Function Strobe
IR-6SD
IR-6BD
IR-6S
IR-6B
IR-5S
Mode Sound 1
IR-5B
Stand by Blackout t he unit
IR-5C
IR-4C
Function Strobe
Mode Sound 1
Stand by Blackout t he unit
IS-6S
IS-6B
Function Strobe
Mode Sound 1
Stand by Blackout t he unit
IS-4
Function Strobe
Mode Sound
Stand by Blackout t he unit
IS-3
Function Strobe
Mode Sound
1.Gobo/Color sync. strobe
2.Sync. st robe
3.Two-light strobe
(LED off )
1.Gobo/Color sync. strobe
2.Sync. st robe
3.Two-light strobe
(LED off )
1.Gobo/Color sync. strobe
2.Sync. st robe
3.Two-light strobe
(LED off )
1.Gobo/Color sync. strobe
2.Sync. st robe
3.Two-light strobe
(LED off )
1.Gobo/Color sync. strobe
2.Sync. st robe
3.Two-light strobe
(LED off )
X/Y moving pattern
X/Y moving pattern selection
( 12 patterns )
Sound 2
(LED normal blinking)
Chase pattern s election
( 6 patterns )
Sound 2
(LED normal blinking)
X/Y moving pattern selection
( 12 patterns )
Sound 2
(LED normal blinking)
Gobo/Color selection
1.Hold on for gobo change.
2.Press shortly for color change.
Slow
(LED on)
Gobo/Color selection
Slow
(LED on)
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
Slow/Sound 3
(LED on)
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
Slow
(LED on)
Color/Gobo selection
1. Hold on for gobo change.
2. Press shortly for color
Slow/Sound 3
(LED on)
change.
change.
change.
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
Position/ Latch
(LED fast blinking )
Dimmer setting
Latch
(LED fast blinking )
X/Y moving setting
1.Pan position
2.Tilt position
Position/ Latch
(LED fast blinking )
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal) or
(2 light show) mode or (3 light show) mode or (4 light show). Once
the mode has been selected, press the ENTER button to setup or automatically return to the
main functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Blackout Mode
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (yes
blackout) or (no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change after
8 seconds. To go back to the functions without any change press the MENU button again.
Color Mode
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal) or
11F
(split color) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Pan I nversion
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal) or
(pan inversion) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Tilt I nversion Barrel Rotation Inversion
Press the MENU button up to when the ( ) is showing on the display.
Pressing ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or (tilt/barrel rotation inversion) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change press the
MENU button again.
Dimmer Inversion
Fixture Hours
Press the MENU button up to when t he is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or (dim mer inversion) mode. O nce t he mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any
change after 8 seconds. To go back to the functions without any change press the MENU
button again.
Led Display
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER button to setup
or automatically return to the main functions without any change after 8 seconds. To go back
to the functions without any change press the MENU button again.
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
when the is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
button again return to the mode (display normal). To go back to the functions press
the MENU button again.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Focus Adjust
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button, the unit will focus on center position. To go back to the functions press the MENU
button again.
Self-Test
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the unit will run self-test by built in program. To go back to the functions press the
MENU button again.
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
Reset
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
functions press the MENU button again.
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By IL-0824 ( please refer to the user guide of iLead controller ) or universal DMX
controller
No need to turn the unit off when you change the DMX address, as new DMX address setting
12F
will be effected at once. Every time you turn the unit on, it will show its item number on the
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in
programs.
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to give
an automatic, sound activated, synchronized light show. This function is good when you want
an instant show. Its DMX input jack will have nothing plugged into it, and Its master LED will
be constantly on and sound LED will flash to the music. The other units will have to set in
slave mode and select (normal) or (2 light show) mode (3
light show) mode or (4 light show), Their DMX cables plugged into the DMX input
jacks (daisy chain) and the slave led lights will constantly on.
and only for color-change.
2-light show
In (slave mode), means the unit works normally and means 2-light
show. In order to create a great light show, you can set on the second unit to get
contrast movement to each other, even if you have two units only.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.