Acer UM.QV0EE.P01 User Manual

Acer LCD Monitor

User Guide

Acer LCD Monitor User Guide Original Issue: 12/2017

English

Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents

hereof and specically disclaims the implied warranties of merchantability or tness for a

particular purpose.

Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the

label afxed to your computer. All correspondence concerning your unit should include the

serial number, model number and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.

Acer LCD Monitor User Guide

Model number: __________________________________

Serial number: ___________________________________

Date of purchase: ________________________________ Place of purchase: ________________________________

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’

product names or trademarks are used herein for identication purposes only and belong to

their respective companies.

Information for your safety and comfort

Safety instructions

Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product.

Acer monitor is purposed for video and visual display of information obtained from electronic devices.

Special notes on LCD monitors

The following are normal with the LCD monitor and do not indicate a problem.

• Due to the nature of the uorescent light, the screen may icker during initial use. Turn off the power switch and then turn it on again to make sure the icker disappears.

• You may nd slightly uneven brightness on the screen depending on the desktop pattern

you use.

• The LCD screen has 99.99% or more effective pixels. It may include blemishes of 0.01% or less such as a missing pixel or pixel lit all the time.

• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the power switch for a few hours.

English

Cleaning your monitor

Please carefully follow these guidelines when cleaning the monitor:

• Always unplug the monitor before cleaning.

• Use a soft cloth to wipe the screen and cabinet front and sides.

Accessibility

Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet.

Safe listening

To protect your hearing, follow these instructions.

English

• Gradually increase the volume until you can hear it clearly and comfortably and without distortion.

• After setting the volume level, do not increase it after your ears have adjusted.

• Limit the amount of time listening to music at high volume.

• Avoid turning up the volume to block out noisy surroundings.

• Turn the volume down if you can’t hear people speaking near you.

Warnings

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. If the product falls, it could

be seriously damaged.

• Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.

• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a re or electric shock.

Never spill liquid of any kind onto or into the product.

• To avoid dmage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.

• Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage internal devices.

Using electrical power

• This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.

• If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.

• Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip’s input rating.

• This product’s power cord is equipped with a three-wire grounded plug. The plug only ts in a grounded power outlet. Make sure the power outlet is properly grounded before

inserting the power cord plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.

Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.

Note: The grounding pin also provides good protection from unexpected

noise produced by other nearby electrical devices that may interfere with the performance of this product.

• Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements:

detachable type, UL listed/CSA certied, type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.

English

Product servicing

Do not attempt to service this product yourself, as opening or removing covers may expose

you to dangerous voltage points or other risks. Refer all servicing to qualied service

personnel.

Unplug this product from the wall outlet and refer servicing to qualied service personnel

when:

• the power cord or plug is damaged, cut or frayed

• liquid was spilled into the product

• the product was exposed to rain or water

• the product has been dropped or the case has been damaged

• the product exhibits a distinct change in performance, indicating a need for service

• the product does not operate normally after following the operating instructions

Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in

damage and will often require extensive work by a qualied technician to

restore the product to normal condition.

English

Potentially explosive environments

Switch off your device in any area with a potentially explosive atmosphere and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion

or re resulting in bodily injury or even death. Switch off the device near depots, storage and

distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, marked. They include below

deck on boats, chemical transfer or storage facilities, vehicles using liqueed petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such

as grain, dust or metal powders.

Additional safety information

Your device and its enhancements may contain small parts. Keep them out of the reach of small children.

IT Equipment Recycling Information

Acer is strongly committed to environmental protection and views recycling, in the form of salvaging and disposal of used equipment, as one of the company’s top priorities in minimizing the burden placed on the environment.

We at Acer are very conscious of the environmental effects of our business and strive to identify and provide the best working procedures to reduce the environmental impact of our products.

For more information and help when recycling, please go to this website:

http://www.acer-group.com/public/Sustainability/sustainability01.htm

Visit www.acer-group.com for further information on the features and benets of our other products.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle.

For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/

sustainability01.htm

LCD pixel statement

The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,

some pixels may occasionally misre or appear as black or red dots. This has no effect on

the recorded image and does not constitute a malfunction.

This product has been shipped enabled for power management:

• Activate display’s Sleep mode within 5 minutes of user inactivity.

• Wake the monitor when it is in Active Off mode,move the mouse or press any keyboard

key.

Tips and information for comfortable use

Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury.

Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis or other musculoskeletal disorders. The following symptoms may appear in the hands, wrists, arms, shoulders, neck or back:

• numbness, or a burning or tingling sensation

• aching, soreness or tenderness

• pain, swelling or throbbing

• stiffness or tightness

• coldness or weakness

If you have these symptoms, or any other recurring or persistent discomfort and/or pain related to computer use, consult a physician immediately and inform your company’s health and safety department.

The following section provides tips for more comfortable computer use.

English

Finding your comfort zone

Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or raising your sitting height to achieve maximum comfort. Observe the following tips:

• refrain from staying too long in one xed posture

• avoid slouching forward and/or leaning backward

• stand up and walk around regularly to remove the strain on your leg muscles

Taking care of your vision

Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain.

Eyes

English

• Rest your eyes frequently.

• Give your eyes regular breaks by looking away from the monitor and focusing on a

istant point.

• Blink frequently to keep your eyes from drying out.

Display

• Keep your display clean.

• Keep your head at a higher level than the top edge of the display so your eyes point

downward when looking at the middle of the display.

• Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity.

• Eliminate glare and reections by:

• placing your display in such a way that the side faces the window or any light source

• minimizing room light by using drapes, shades or blinds

• using a task light

• changing the display’s viewing angle

• using a glare-reduction lter

• using a display visor, such as a piece of cardboard extended from the display’s top

front edge

• Avoid adjusting your display to an awkward viewing angle.

• Avoid looking at bright light sources, such as open windows, for extended periods of

time.

Developing good work habits

Develop the following work habits to make your computer use more relaxing and productive:

• Take short breaks regularly and often.

• Perform some stretching exercises.

• Breathe fresh air as often as possible.

• Exercise regularly and maintain a healthy body.

English

Acer Incorporated

New Taipei City 221, Taiwan

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi

Declaration of Conformity

We,

Acer Incorporated

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan

And,

Acer Italy s.r.l.

Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it

ct: LCD Monitor

Produ Trade Name: Acer Model Number: SKU Number:

We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following harmonized standards and/or other relevant standards have been applied:

EMC Directive: 2014/30/EU

EN 55032:2012/AC:2013 Class B EN 61000-3-2:2014-3- Class D

LVD Directive: 2014/35/EU

EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013

RoHS Directive: 2011/65/EU

EN 50581:2012

ErP Directive: 2009/125/EC

Regulation (EC) No. 1275/ 2008; EN 50564:2011

Year to begin affixing CE marking: 2017.

VG240Y VG240Y xxxxxx;

(“x” = 0~9, a ~ z, A ~ Z, or blank)

EN 55024:2010 EN 61000-3-3:2013

_______________________________

RU Jan / Sr. Manager Acer Incorporated (Taipei, Taiwan)

Dec.25, 2017

Oct.31,2017

Date

Acer America Corporation

333 West San Carlos St., San Jose

English

Fax : 254-298-4147

Federal Communications Commission

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

The following local Manufacturer /Importer is responsible for this declaration:

Product: LCD Monitor

Model Number: VG240Y

Suite 1500 CA 95110, U. S. A. Tel : 254-298-4000

www.acer.com

SKU Number:

Name of Responsible Party: Acer America Corporation

Address of Responsible Party:

Contact Person: Acer Representative

Phone No.: 254-298-4000

Fax No.: 254-298-4147

VG240Y xxxxxx (“x” = 0~9, a ~ z, or A ~ Z)

333 West San Carlos St. Suite 1500 San Jose, CA 95110 U. S. A.

Information for your safety and comfort iii

Safety instructions iii Special notes on LCD monitors iii

Cleaning your monitors iii Accessibility iv Safe listening iv Warnings iv Using electrical power iv Product servicing v

Potentially explosive environments vi Additional safety information vi IT Equipment Recycling Information vi Disposal instructions vi LCD pixel statement vii Tips and information for comfortable use vii

Finding your comfort zone vii

Taking care of your vision viii

Developing good work habits viii Declaration of Conformity ix Federal Communications Commission Declaration of Conformity x

Unpacking 1

Attaching the base (for selected models) 2 Tilt 2 Connecting the adapter and AC Power cord 3 Power saving

Display Data Channel (DDC)

Connector pin assignment 4

15-pin color display signal cable 4

19-pin color display signal cable 5

20-pin color display signal cable 5

Standard timing table 6

English

Contents

Installation 7 Users controls 8

Panel controls 8 Using the Shortcut Menu 9 The Function page 10

Troubleshooting 15

DP/HDMI 1.4/VGA Mode (Optional) 15

Unpacking

Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future.

English

LCD monitor Quick start guide AC Power cord

LCD Monotor VG0 series-VG240Y

USER GUIDE

HDMI 1.4 Cable

(Optional)

Audio Cable

(Optional)

VGA cable

(Optional)

DP Cable

(Optional)

SCREEN POSITION ADJUSTMENT

-5°

In oder to optimize the best viewing position, you can adjust the tilt of the monitor.

• Attaching the Base

Note: Remove the monitor and monitor base from its packaging.Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen.

• Tilt

Please see the illustration below for an example of the tilt range. Only at the highest point can 20 degrees of recline be offered for the angle of elevation.

English

20°

Connecting the adapter and AC Power cord

• Check rst to make sure that the power cord you use is the correct type required for

your area.

• The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area. No user-adjustment is required.

English

• Plug one end of the AC power cord to the Adapter, and plug the other end into an AC outlet.

• For units using 120 V AC: Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.

• For units using 220/240 V AC: Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set

should have the appropriate safety approvals for the country in which the equipment will be installed.

Power saving

The monitor will be driven into "Power Saving" mode by the control signal from the display

controller, as indicated by the amber-color power LED.

State LED Light

ON Blue

Power Saving Mode Amber

The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 3 seconds.

Display Data Channel (DDC)

To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play. The DDC is a communication protocol through which the monitor automatically informs the host system about its capabilities; for example, supported resolutions and corresponding timing. The monitor supports the DDC2B standard.

15-pin color display signal cable

PIN No. Description PIN No. Description

1 Red 9 +5 V

2 Green 10 Logic ground

3 Blue 11 Monitor ground

4 Monitor ground 12 DDC-serial data

5 DDC-return 13 H-sync

6 R-ground 14 V-sync

7 G-ground 15 DDC-serial clock

8 B-ground

English

19-pin color display signal cable

English

PIN No. Description PIN No. Description

1 TMDS Data2+ 2 TMDS Data2 Shield

3 TMDS Data2- 4 TMDS Data1+

5 TMDS Data1 Shield 6 TMDS Data1-

7 TMDS Data0+ 8 TMDS Data0 Shield

9 TMDS Data0- 10 TMDS Clock+

11 TMDS Clock Shield 12 TMDS Clock-

13 CEC 14 Reserved (N.C. on device)

15 SCL 16 SDA

17 DDC/CEC Ground 18 +5V Power

19 Hot Plug Detect

20-pin color display signal cable

PIN No. Description PIN No. Description

1 Lane0(p) 2 GND

3 Lane0(n) 4 Lane1(p)

5 GND 6 Lane1(n)

7 Lane2(p) 8 GND

9 Lane3(n 10 Lane3(p)

11 GND 12 Lane3(n)

13 Cong1 14 Cong2

15 AUX_CH (n) 16 GND

17 AUX_CH (p) 18 Hot Plug Detect

19 DP Power_Return 20 DP Power

* only for certain models

Standard timing table

VESA MODE

MODE Resolution

1 VGA 640x480 60Hz 2 MAC 640x480 66.662Hz 3 VESA 720x400 70Hz 4 SVGA 800x600 56Hz 5 SVGA 800x600 60Hz 6 XGA 1024x768 60Hz 7 XGA 1024x768 70Hz 8 VESA 1152x864 75Hz

9 SXGA 1280x1024 60Hz 10 VESA 1280x720 60Hz 11 WXGA 1280x800 60Hz 12 WXGA+ 1440x900 60Hz 13 WSXGA+ 1680x1050 60Hz 14 UXGA 1920x1080 60Hz 15 UXGA 1920x1080 75Hz

English

Installation

1. Turn off your computer and unplug your computer's power cord.

2. Connect the signal cable to the VGA (optional) and /or HDMI 1.4 (optional) and /or DP (optional) input socket of the

monitor, and the VGA (optional) and /or HDMI 1.4 (optional) and /or DP (optional) output socket of the graphics card

on the computer. Then tighten the thumbscrews on the signal cable connector.

3. Optional: Connect the audio input socket (AUDIO IN) of the LCD monitor and the line-out port on the computer with the audio cable.

4. Insert the monitor power cable into the power port at the back of the monitor.

English

5. Connect the power adapter and power cord to the monitor, then to a properly grounded AC outlet.

------------------------------------------------------------------------------------------

Note: Audio output is only for audio output model. Please check user manual for more instruction.

FreeSync:

It can allow a FreeSync supported graphics source to dynamically adjust display refresh rate based on

typical content frame rates for power efcient, virtually stutter free and low-latency display update.

User Controls

External controls

English

1 Power button Turns the monitor on/off.Blue indicates power on. Amber indicates

2 Function key

3 Function key

4 Function key

5 Function key

standby/ power saving mode. a. Press to view Main page. Press again to enter hotkey1 function.

b. When the Function Menu is active, press this key to view the basic

information for your monitor and current input or reset the custom color settings to the factory defaults.

a. Press to view Main page.Press again to enter hotkey2 function. b. When the Function Menu is active, press this button to select

select scenario mode or game mode .

a. Press to view Main page.Press again to enter Input select

function.

b. When the Function Menu is active, this button will quit the OSD.

a. Press to view

the Function Menu.

b. The single toggle button on the backside of the Display bezel

operates like a joystick. To move the cursor, simply toggle the button in four directions. Press the button to select desired option. Bright gray indicates operable. Dark gray indicates inoperable.

Main page

.Press again to enter next function in

Using the Shortcut Menu

Brightness

Input

HDMI

Mode

Standard

-------------------------------------------------------------------------------------------------------------

Note: The following content is for general reference only. Actual product specications

may vary.

The OSD (onscreen display) can be used to adjust the settings of your LCD monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality and

English

general settings. For advanced settings, please refer to following page:

Main page

1. Menu OSD

2. Hot Key1 (Modes, Volume, Brightness,Gamma,

Contrast, Blue Light, Over Drive)

3. Hot Key2 (Modes, Volume, Brightness,Gamma, Contrast, Blue Light, Over Drive)

4. Input selection

Hot key1 (default: Standard mode)

To choose game mode(G1, G2, G3) which user-dened prole to use or scenario mode (User, Standard, ECO, Graphics, Movie)

Modes

Acon

Racing

Sports

User

Standard

Move

ECO

Graphics

Movie

Hot key2 (default: Brightness)

Open the Brightness control and select your preferred brightness setting . When you are done, press the joystick to quit current page and store.

Adjust

Brightness

Selecting the input

Input

HDMI 1

Auto Source

Move

Exit

Input

Mode - User

Oﬀ

Brightness

Contrast

Blue Light

ACM

Oﬀ

Super Sharpness

Auto Conﬁg

H. Posion

Picture

Enter

Move

Black Boost

Mode - User

Picture

Clock

Focus

V. Posion

Color

OSD

System

Save Sengs to...

Color

OSD

System

Save Sengs to...

Enter

Move

Audio

Gaming

Open the Input control and select HDMI 1, HDMI 2,VGA or Auto Source. When you are

done, press the joystick to exit current page and store.

The Function page

Open the Function page to adjust the functions, settings which you want using the arrows.

When you are done, toggle the joystick to the left or right to go back one level or use

to exit current page and store.

Picture

English

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select Picture from the OSD.Then toggle to the

3. Toggle to the left or right to adjust the sliding scales.

right to navigate to the element you wish to adjust and press the joystick to enter it.

4. The Picture menu can be used to adjust the Brightness, Contrast, Black Boost, Blue

Mode - User

2.2

Warm

Gamma

Color Temp.

R Gain

G Gain

B Gain

Picture

Mode - User

Oﬀ

Picture

Color

sRGB Mode

6-axis Saturate

R Bias

G Bias

B Bias

6-axis Hue

Enter

Move

Enter

Move

Oﬀ

Grayscale Mode

Color

OSD

System

Save Sengs to...

Audio

OSD

System

Save Sengs to...

Audio

Modes

Gaming

Light, ACM,Super Sharpness,Auto Cong,H. Position,V. Position,Focus and Clock.

5. Brightness: Adjust the brightness from 0 to 100.

-----------------------------------------------------------------------------------------------------------

Note: Adjusts the balance between light and dark shades.

6. Contrast: Adjust the contrast from 0 to 100.

English

-----------------------------------------------------------------------------------------------------------

Note: Sets the degree of difference between light and dark areas.

7. Black Boost: Adjust the black level from 0 to 10. Enhances shadows by increasing the brightness without changing lighter shades.

8. Blue Light: Filters out blue light to protect your eyes by adjusting how much blue light is shown -- 80%, 70%, 60%, or 50%.

-----------------------------------------------------------------------------------------------------------

Note: Higher values allow more blue light through. For the best protection select a lower value.

9. ACM: Turn ACM on or off. The default is off.

10. Super Sharpness: Turn the Super Sharpness On or Off. Super Sharpness technology can simulate high-resolution images by boosting the pixel density of the original source to make images sharper and clearer.

Color

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select Color from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it.

3. Toggle to the left or right to adjust the sliding scales.

Mode - Stardard

Picture

Volume

Enter

Move

Oﬀ

Mute

Color

OSD

System

Save Sengs to...

Audio

Gaming

Mode - User

Picture

Color

Over Drive

Normal

Free Sync

Oﬀ

MPRT

Enter

Move

Oﬀ

Aim Point

OSD

System

Save Sengs to...

Audio

Gaming

4. Gamma mode allows you to adjust the luminance tone.The default value is 2.2 (standard

value for Windows).

5. Color temperature: Default is warm. You can choose Cool, Normal, Warm, Bluelight or

User.

6. Modes:To choose scenario mode.

7. Grayscale Mode:To choose Grayscale mode.

8. sRGB: Default is off. You can turn sRGB on or off to better color match with peripheral devices, such as printers and digital cameras.

9. 6-axis Hue: Adjust the red, green, blue, yellow, magenta and cyan hue.

10. 6-axis Saturate: Adjust the red, green, blue, yellow, magenta and cyan saturation.

Audio

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select Audio from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it.

3. Toggle to the left or right to adjust the sliding scales.

4. Volume: Adjust the volume

5. Mute:To choose mute on/off .

Gaming

English

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select Gaming from the OSD.Then toggle to

Mode - User

120

English

OSD Timeout

Picture

Color

Language

Oﬀ

Transparency

Enter

Move

Oﬀ

Refresh Rate Num

Oﬀ

OSD Lock

OSD

System

Save Sengs to...

Audio

Gaming

the right to navigate to the element you wish to adjust and press the joystick to enter it.

3. Toggle to the left or right to adjust the sliding scales.

4. Over Drive: Select Off, Normal, or Extreme.

5. FreeSync: To control support FreeSync or not, default is On.

English

---------------------------------------------------------------------------------------------------------

Note:

1. If FreeSync is “ON”, then the Over Drive selection is set to “Normal” automatically.

2. If FreeSync is “OFF”, then the user can set Over Drive to either one of the

three settings including: (a) Extreme (b) Normal (c) Off.

6. MPRT: To choose whether to support dynamic picture more clean control, default is Off.

---------------------------------------------------------------------------------------------------------

Note:

1. PIP/PBP mode is not support MPRT.

2. HDR setting: "Auto" is not support MPRT.

3. MPRT set "On", when to turn on FreeSync, will auto set MPRT is "Off".

4. MPRT set "On", when to adjustment (Brightness, Blue Light, ACM), will auto set MPRT is "Off".

5. MPRT function does not affect the (Logo, Aim Point, Message and Input Icon) brightness.

6. MPRT setting "On", when detection of Input Timing <75Hz, will auto off the MPRT and gray out to disable.

7. MPRT = (Normal or Extreme), because the IC control dynamic picture is

cleaner, so the overall Brightness will be dark, "Extreme" will be darker than

“Normal”.

7. Aim point: Show an Aim point on the screen for shooting games.

-----------------------------------------------------------------------------------------------------------

Note: In PBP mode the Aim point not displayed.

OSD

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select OSD from the OSD.Then toggle to the

Mode - User

HDMI

Picture

Color

Input

Full

Hot Key Assignment

DDC/CI

Wide Mode

HDMI Black Level

Normal

Auto Source

Enter

Move

Quick Start Mode Oﬀ

OSD

System

Save Sengs to...

Audio

Gaming

right to navigate to the element you wish to adjust and press the joystick to enter it.

3. Toggle to the left or right to adjust the sliding scales.

4. Language: Set the OSD menu language.

5. OSD timeout: Adjust the delay before turning off the OSD menu.

6. Transparency: Select the transparency when using gaming mode. The transparency

can be 0% (OFF), 20%, 40%, 60%, or 80%.

7. Refresh rate num: Display the panel’s current refresh rate on the screen.

-----------------------------------------------------------------------------------------------------------

Note: If FreeSync set "On" you can see the V Frequency to changes in the OSD.

8. OSD Lock: To choose OSD lock on/off.

Note:

OSD Locked:

• Set the OSD Lock to "On" by the OSD option and press "Enter" to execute the

All Key lock function.

• The "OSD Locked" message will be displayed in the middle of the screen.

• LED lights will be changed from blue light to orange light.

• Press any Key screen to prompt "OSD Locked" message.

OSD Unlocked:

• In normal display condition to press the "Navi Key" in the middle of more than 3 seconds to trigger "OSD Unlock".

• The "OSD Unlock" message will be displayed in the middle of the screen.

• LED lights will be restored to blue light.

English

System

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select System from the OSD.Then toggle to the

3. Toggle to the left or right to adjust the sliding scales.

4. Input: Select the source from HDMI 1,HDMI 2 or VGA.

right to navigate to the element you wish to adjust and press the joystick to enter it.

5. Auto Source:The default is “On”, can support auto search for signal source in order.

6. Wide mode: You can select which screen aspect you are using. The options are Full,

7. Hotkey Assigment: Select the function of shortcut key 1(Modes, Volume, Brightness,

8. DDC/CI: Allows the monitor settings to be set through the software on the PC.

9. HDMI Black level setting.

10. Quick start mode: Select Off or On. Turn on to speed up boot speed.

-----------------------------------------------------------------------------------------------------------

Note: Surround application must set Auto Source is “Off”.

Aspect .

Gamma, Contrast, Blue Light, Over Drive) and shortcut keys 2 (Modes, Volume, Brightness, Gamma, Contrast, Blue Light, Over Drive)

-----------------------------------------------------------------------------------------------------------

Note: DDC/CI, short for Display Data Channel/Command Interface, which allows monitor controls to be sent via software.

Save Setting to…(User mode only)

Game Mode Racing

Picture

Game Mode Acon

Game Mode Sports

Mode - User

Enter

Move

Color

OSD

System

Save Sengs to...

Audio

Pertormance

1. Press the MENU key to open the OSD.

2. Toggle the joystick to the up or down to select "Save Setting to..." from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it.

3. Save Setting to some mode: There are three user-dened proles available. When you have decided what settings suit you, save them and system will be able to recall the settings in the future when you turn on these mode.

English

Troubleshooting

Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.

HDMI /VGA Mode (Optional)

English

Problem LED status Remedy

No picture visible Blue Using the OSD menu, adjust brightness and

contrast to maximum or reset to their default setting.

Off Check the power switch.

Check if the AC power cord is properly connected to the monitor.

Amber Check if the video signal cable is properly

connected at the back of monitor.

Check if the computer system is switched on and in power saving/standby mode.

Acer UM.QV0EE.P01 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual