Acer Projector
S1110/T200/XS-S10/S1210/T210/XS-
X10/S1210Hn/S1213/T212/XS-X13/
S1213Hn/T212DT/XS-X13HG/
S1310W/T220/XS-W10/S1310WHn/
S1313W/S1313WHn Series User's
Guide
Copyright © 2012. Acer Incorporated.
All Rights Reserved.
Acer Projector S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/S1213Hn/
T212DT/XS-X13HG/S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn Series User's Guide
Original Issue: 4/2012
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer Projector S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/S1213Hn/
T212DT/XS-X13HG/S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
TM
"HDMI
, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC."
iii
Information for Your Safety and
Comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
• Install the power supply unit before connecting the power cord to the AC
power outlet.
• Unplug the power cord before removing the power supply unit from the
projector.
• If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
• Do not use this product near water.
• Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
• Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
• Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
• To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
• Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
• This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
• If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
• Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
• This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
• Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (14.8 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
• the power cord or plug is damaged, cut or frayed
• liquid was spilled into the product
• the product was exposed to rain or water
• the product has been dropped or the case has been damaged
• the product exhibits a distinct change in performance, indicating a need
for service
• the product does not operate normally after following the operating
instructions
v
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
• Do not look into the projector's lens when the lamp is on. The bright light
may hurt your eyes.
• Turn on the projector first and then signal sources.
• Do not place the product in the following environments:
• Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector are necessary.
• Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
• Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shorten the life span and darken the image.
• Locations near fire alarms.
• Locations with an ambient temperature above 40 ºC/104 ºF.
• Locations where the altitudes are higher than 10000 feet.
• Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
• Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
• Do not face the projector lens to the sun. It can lead to fire.
• When switching the projector off, please ensure the projector completes
its cooling cycle before disconnecting power.
• Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to stop
before turning main power off.
• Do not touch the air outlet grille and bottom plate which become hot.
• Clean the air filter frequently. The temperature inside may rise and cause
damage when the filter/ventilation slots are clogged with dirt or dust.
• Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
• Always open the lens shutter or remove the lens cap when the projector is
on.
• Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
• The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
• Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
• Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
• The product will detect the life of the lamp itself. Please be sure to change
the lamp when warning messages display.
• When changing the lamp, please allow the projector to cool down, and
follow all changing instructions.
• Reset the "Lamp Hour Reset" function from the Onscreen Display
"Management" menu after replacing the lamp module.
• Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
• Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
• This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
"Lamp(s) contain Mercury,
Dispose Properly."
Caution for Listening
To protect your hearing, follow these instructions.
• Increase the volume gradually until you can hear clearly and comfortably.
• Do not increase the volume level after your ears have adjusted.
• Do not listen to music at high volumes for extended periods.
• Do not increase the volume to block out noisy surroundings.
• Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/
Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
viii
First Thing First
Usage Notes
Do:
• Turn off the product before cleaning.
• Use a soft cloth moistened with mild detergent to clean the display
housing.
• Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
• Block the slots and openings on the projector provided for ventilation.
• Use abrasive cleaners, waxes or solvents to clean the unit.
• Use under the following conditions:
• In extremely hot, cold or humid environments.
• In areas susceptible to excessive dust and dirt.
• Near any appliance that generates a strong magnetic field.
• Place in direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
• Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
• To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
• Please do not open or disassemble the product as this may cause electric shock.
• When changing the lamp, please allow the projector to cool down, and follow all
changing instructions.
• This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
• Reset the "Lamp Hour Reset" function from the Onscreen Display "Management"
menu after replacing the lamp module.
• When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
• Turn on the projector first and then the signal sources.
• Do not use lens cap when projector is in operation.
• When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Information for Your Safety and Comfort iii
First Thing First viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 2
Projector Overview 3
Projector Outlook 3
Control Panel 4
Remote Control Layout 5
Getting Started 7
Connecting the Projector 7
Turning the Projector On/Off 9
Turning On the Projector 9
Turning Off the Projector 10
Adjusting the Projected Image 11
Adjusting the Height of the Projected Image 11
How to Optimize Image Size and Distance 12
How to Get a Preferred Image Size
by Adjusting Distance and Zoom 14
User Controls 16
Installation Menu 16
Acer Empowering Technology 17
Onscreen Display (OSD) Menus 18
Color 19
Image 21
Contents
Setting 24
Management 27
Audio 28
Timer 28
Language 29
Appendices 30
Troubleshooting 30
LED & Alarm Definition Listing 34
Replacing the Lamp 35
Ceiling Mount Installation 36
Specifications 39
Compatibility Modes 41
Regulations and safety notices 45
English
Introduction
Product Features
This product is a single-chip DLP® projector, including the following
outstanding features:
1
• DLP
®
technology
• S1110/T200/XS-S10: Native 800 x 600 SVGA resolution
Auto / 4:3 / 16:9 aspect ratio supported
S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/S1213Hn/T212DT/XSX13HG:
Native 1024 x 768 XGA resolution
Auto / 4:3 / 16:9 aspect ratio supported
S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn: Native 1280 x 800
WXGA resolution
Auto/ Full / 4:3 /16:9 / L.Box aspect ratio supported
• Acer ColorBoost technology delivers vivid, life-like images
• High brightness and contrast ratio
• Versatile display modes (Bright, Presentation, Standard, Video, Picture,
Game, Education, User) enable optimum performance in any situation
• NTSC/PAL/SECAM compatible and HDTV (720p, 1080i, 1080p) supported
• Lower power consumption and economy (ECO) mode extends lamp life
• Acer EcoProjection Technology delivers Intelligent power management
approach and physical efficiency improvement
• Empowering Key reveals Acer Empowering Technology functions (Acer
eView, eTimer, ePower Management) for easy adjustment of settings
• Advanced keystone correction delivers optimum presentations
• Multi-language Onscreen Display (OSD) menus
• Manual focus projection lens
• 2X digital zoom and pan move function
• Microsoft
®
Windows® 2000, XP, 7, Vista®, Macintosh OS compliant
2
English
Acer Projector
This CD contains
• User’s manual
• Quick Start Guide
• Acrobat
®
Reader
®
www.acer.com
Quick Start Guide
Package Overview
This projector comes with all the items shown below. Check to make sure you
have them all. Contact your dealer immediately if any thing is missing.
Projector with lens cap Power cord VGA cable
Acer Projector
Security Card
BACK
ENTER
PgUp
PgDn
SD/USB A HDMI/DV I LAN/WiFi USBB
Security card User’s guide (CD-ROM) Remote control
Quick start guide Battery x 2 Dust filter
(Optional)
English
Projector Overview
AUDIO-R
AUDIO-L
AUDIO
IN 1
AUDIO
IN 2
AUDIO
OUT
VGA IN 1
VGA IN 2
VGA OUT
HDMI
USB B
LAN
RS232
S-VIDEO
VIDEO
AUDIO-R
AUDIO-L
AUDIO
IN 1
AUDIO
IN 2
AUDIO
OUT
VGA IN 1
VGA IN 2
VGA OUT
USB BRS232
S-VIDEO
VIDEO
10 1 1211 2351364
S1213Hn
1 11 2351364
S1213
23 4 56
8
7
9
1
(S1110/T200/XS-S10/S1210/T210/XSX10/S1310W/T220/XS-W10)
(S1210Hn/S1213Hn/T212DT/XS-X13HG/
S1310WHn/S1313WHn)
(S1213/T212/XS-X13/
S1313W)
Projector Outlook
Front / upper side
5
1
2
3
4
# Description # Description
1 Control panel 5 Power key and Power indicator LED
2 Projection lens 6 Focus ring
3 Elevator button 7 Remote control receiver
4Lens cap
6
7
3
Rear side
# Description # Description
1 USB connector 8 Tilt adjusting wheel
2 Monitor loop-through output connector 9 Kensington™ lock port
3 PC analog signal/HDTV/component
video input connector
4 RS232 connector 11 Remote control receiver
5 S-Video input connector
Composite video input connector
6 Audio input connector
Audio output connector
7 Power socket
10 LAN (RJ45 port for 10/100M
Ethernet)
12 HDMI input connector
13 Audio input connector (L/R)
4
English
Control Panel
1
6
2
3
2
7
8
9
4
5
10
3
# Function Description
1 LAMP Lamp Indicator LED
2 Power key and Power
indicator LED
3 Keystone Adjusts image distortion caused by tilting
4MENU
Refer to the "Turning the Projector On/
Off" section.
projection (±40 degrees).
• Launches the Onscreen Display (OSD)
menu, returns to the previous step for
the OSD menu operation or exits the
OSD menu.
• Confirms your selection of items.
5 HIDE Hides the screen picture.
6 TEMP Temp Indicator LED
7 SOURCE Chooses RGB, component video, S-Video,
composite video or HDTV source.
8 Four directional select keys Selects items or makes adjustments to your
selection.
9 Empowering key Enables unique Acer functions: eView,
eTimer, ePower Management.
10 RESYNC Automatically synchronizes the projector
to the input source.
English
Remote Control Layout
BACK
ENTER
SD/USB A H DMI/DVI LAN/WiFi USBB
5
PgUp
PgDn
# Function Description
1 POWER Refer to the "Turning the Projector On/Off" section.
2 ASPECT RATIO To choose the desired aspect ratio.
3 ZOOM Zooms the projector display in or out.
4 RESYNC Automatically synchronizes the projector to the input
source.
5 Keystone Adjusts image distortion caused by tilting projection
(±40 degrees).
Four
Selects items or makes adjustments to your selection.
directional
select keys
6 Keypad 0~9 Press "0~9" to input a password in the "Setting" >
"Security" OSD.
7 VGA To change source to VGA. This connection supports
analog RGB, YPbPr (480p/576p/720p/1080i/1080p),
and YCbCr (480i/576i).
8 COMPONENT (No function)
9 S-VIDEO To change source to S-Video.
10 HDMI™;
HDMI™/DVI
To change source to HDMI™ (or DVI) (for the model
with HDMI™ or DVI connector). (For S1210Hn/
S1213Hn/T212DT/XS-X13HG/S1310WHn/S1313WHn)
11 Infrared
Sends signals to the projector.
transmitter
12 Empowering key Enables unique Acer functions: eView, eTimer,
ePower Management.
6
English
VZ.JDW00.001
# Function Description
13 FREEZE To pause the screen image.
14 HIDE Press "HIDE" to hide screen image; press again to
display the image.
15 SOURCE Chooses RGB, component video, S-Video, composite
video or HDTV source.
16 MENU
• Launches the Onscreen Display (OSD) menu,
returns to the previous step for the OSD menu
operation or exits the OSD menu.
• Confirms your selection of items.
17 PgUp/PgDn For computer mode only. Use this button to select the
next or previous page. This function is only available
when connected to a computer via a USB cable.
18 VIDEO To change source to Composite video.
19 MUTE To turn on/off the volume.
20 WIRELESS;
LAN/WiFi
21
Rewind
Play/Pause
Stop
Fast-forward
22 SD/USB A (No function)
23 USB B (No function)
(No function)
(No function)
English
Getting Started
DVD player,
Set-top box,
HDTV receiver
VGA
RS232
Video/S-Video
Output
Display
Speakers
Connecting the Projector
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1310W/T220/XS-W10
5
USB
D-Sub
RBG
9
D-Sub
8
RS232
7
2
RBG
2
3
6
7
R
W
Y
5
4
1
USB
D-Sub
D-Sub
HDTV adapter
RS232
# Description # Description
1Power cord 6S-Video cable
2 VGA cable 7 RS232 cable
3 VGA to component video/HDTV
adapter
4 Composite video cable 9 3 RCA component cable
5 Audio cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
8 USB cable
Y
5
8
English
AUDIO-R
AUDIO-L
AUDIO
IN 1
AUDIO
IN 2
AUDIO
OUT
VGA IN 1
VGA IN 2
VGA OUT
HDMI
USB B
LAN
RS232
S-VIDEO
VIDEO
AUDIO-R
AUDIO-L
AUDIO
IN 1
AUDIO
IN 2
AUDIO
OUT
VGA IN 1
VGA IN 2
VGA OUT
USB BRS232
S-VIDEO
VIDEO
USB
USB
S1213Hn
S1213
RS232
RBG
RBG
HDTV adapter
RS232
D-Sub
7
D-Sub
D-Sub
2
5
5
6
5
2
1
R
W
R
L
L
R
9
3
Y
10
10
11
8
D-Sub
4
Y
5
Y
DVD player,
Set-top box,
HDTV receiver
VGA
RS232
Video/S-
Video
Output
Display
Speakers
• S1210Hn/S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG/S1313W/
S1310WHn/S1313WHn
# Description # Description
1 Power cord 7 RS232 cable
2 VGA cable 8 USB cable
3 VGA to component video/HDTV
adapter
4 Composite video cable 10 RJ45 cable
5 Audio cable 11 HDMI cable
6S-Video cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
9 3 RCA component cable
English
Turning the Projector On/Off
2&3
1
Lens cap
Turning On the Projector
1 Remove the lens cap.
2 Ensure that the power cord and signal cable are securely connected.
The Power LED will light red.
3 Turn on the projector by pressing (POWER) on the control panel or
remote control, and the Power indicator LED will turn blue.
4 Turn on your source (computer, notebook, video player, etc.). The
projector will detect your source automatically.
• If the screen displays "No Signal", please make sure the signal cables
are securely connected.
• If you connect to multiple sources at the same time, use "SOURCE" on
the control panel or remote control, or the direct source key on the
remote control to switch between inputs.
9
10
English
Turning Off the Projector
1 To turn the projector off, press the power button. This message
appears:
"Please press the power button again to complete the shutdown process."
Press the power button again.
2 The LED power indicator will turn solid red to indicate standby mode.
3 It is now safe to unplug the power cord.
When Instant Resume is selected:
1 The LED power indicator will turn RED and blink rapidly after the
projector is turned off, and the fan(s) will continue to operate for
about 2 minutes to ensure that the system cools properly.
2 As long as the power cord remains plugged in, you can press the
power button to turn the projector immediately back on anytime
during the 2-minute shutdown process.
3 Once the system has finished cooling, the LED power indicator will
stop blinking and turn solid red to indicate standby mode.
4 It is now safe to unplug the power cord.
Warning indicators:
• "Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp will automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
• "Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and
the
LED lamp indicator turns solid red, contact your local
reseller or service center
.
11
English
Tilt adjusting wheel
Elevator
button
Elevator foot
Adjusting the Projected Image
Adjusting the Height of the Projected Image
The projector is equipped with an elevator foot for adjusting the image height.
To raise the image:
1 Press the elevator button.
2 Raise the image to the desired height angle, then release the button
to lock the elevator foot into position.
3 Use Tilt adjusting wheel to fine-tune the display angle.
To lower the image:
1 Press the elevator button.
2 Lower the image to the desired height angle, then release the button
to lock the elevator foot into position.
3 Use Tilt adjusting wheel to fine-tune the display angle.
1
3
2
12
English
C
A
B
1 m
Desired distance
Height:
160 cm
From
base to
top of
image
81"
How to Optimize Image Size and Distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/
S1213Hn/T212DT/XS-X13HG
If the projector is 1 m from the screen, good image quality is possible for image
sizes around 81".
Note: Remind as below figure, the space of 160 cm height is
required when located at 1 m distance.
Desired
Distance
(m)
< A >
Diagonal
(inch)
< B >
Screen Size
W (cm) x H (cm)
From base to
top of image
0.5 40 82 x 61 80
0.6 48 98 x 74 96
0.7 56 115 x 86 112
0.8 65 131 x 98 128
0.9 73 148 x 111 144
1 81 164 x 123 160
1.5 121 246 x 184 240
2 161 328 x 246 320
2.5 202 410 x 307 400
3 242 492 x 369 480
3.7 299 607 x 455 591
Zoom Ratio: 1.0 x
(cm)
< C >
13
English
C
A
B
4 m
Desired distance
Height:
510 cm
From
base to
top of
image
379"
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn
If the projector is 4 m from the screen, good image quality is possible for image
sizes around 379".
Note: Remind as below figure, the space of 510 cm height is
required when located at 2 m distance.
Desired
Distance
(m)
< A >
Diagonal
(inch)
< B >
Screen Size
W (cm) x H (cm)
From base to
top of image
0.5 47 102 x 64 70
1 95 204 x 128 140
0.5 142 306 x 191 210
2 189 408 x 255 281
2.5 237 510 x 319 351
3 284 612 x 383 421
3.5 332 714 x 446 491
4 379 816 x 510 561
4.5 426 918 x 574 631
5 474 1020 x 638 702
6 568 1224 x 765 842
Zoom Ratio: 1.0 x
(cm)
< C >
14
English
Desired distance
Height:
99 cm
From
base to
top of
image
50"
Desired
image size
0.6 m
How to Get a Preferred Image Size by Adjusting
Distance and Zoom
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/
S1213Hn/T212DT/XS-X13HG
To obtain an image size of 50" set the projector at a distance 0.6 m from the
screen.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
< A >
30 61 x 46 0.4 0.4 59
40 81 x 61 0.5 0.5 79
50 102 x 76 0.6 0.6 99
60 122 x 91 0.7 0.7 119
70 142 x 107 0.9 0.9 139
80 163 x 122 1.0 1.0 158
90 183 x 137 1.1 1.1 178
100 203 x 152 1.2 1.2 198
120 244 x 183 1.5 1.5 238
150 305 x 229 1.9 1.9 297
180 366 x 274 2.2 2.2 357
200 406 x 305 2.5 2.5 396
250 508 x 381 3.1 3.1 495
300 610 x 457 3.7 3.7 594
Zoom Ratio: 1.0 x
W (cm) x H (cm)
Max zoom
< B >
B&C
Min zoom
< C >
A
D
From base to top of
image < D >
English
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn
D
B&C
A
Desired distance
Height:
74 cm
From
base to
top of
image
50"
Desired
image size
0.5 m
To obtain an image size of 50" set the projector at a distance 0.5 m from the
screen.
15
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
< A >
30 65 x 40 0.3 0.3 44
40 86 x 54 0.4 0.4 59
50 108 x 67 0.5 0.5 74
60 129 x 81 0.6 0.6 89
70 151 x 94 0.7 0.7 104
80 172 x 108 0.8 0.8 118
90 194 x 121 0.9 0.9 133
100 215 x 135 1.1 1.1 148
120 258 x 162 1.3 1.3 178
150 323 x 202 1.6 1.6 222
180 388 x 242 1.9 1.9 267
200 431 x 269 2.1 2.1 296
250 538 x 337 2.6 2.6 370
300 646 x 404 3.2 3.2 444
Zoom Ratio: 1.0 x
W (cm) x H (cm)
Max zoom
< B >
Min zoom
< C >
From base to top of
image < D >
16
English
(S1110/T200/XS-S10/S1210/T210/XSX10/S1213/T212/XS-X13/S1310W/
T220/XS-W10/S1313W)
(S1210Hn/S1213Hn/T212DT/
XS-X13HG/S1310WHn
/
S1313WHn)
User Controls
Installation Menu
The Installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No
signal input" is displayed on the screen.
1 Turn on the projector by pressing (POWER) on the control panel or
remote control.
2 Press "MENU" on the control panel or remote control to launch the
OSD for projector installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration
and alignment settings, such as screen size and distance, focus and
more.
4 The Installation menu includes the following options:
• Projection method
• Menu location
• Keystone settings
• Language settings
• Reset to factory default functions
Use the up and down arrow keys to select an option, the left and right arrow keys to
adjust selected option settings, and the right arrow key to enter a submenu for
feature setting. The new settings will be saved automatically upon exiting the menu.
5 Press "MENU" anytime to exit the menu and return to the Acer
welcome screen.
English
Acer Empowering Technology
17
Empowering Key
Acer eView Management
Acer Empowering Key provides three
Acer unique functions: "Acer eView
Management", "Acer eTimer
Management", and "Acer ePower
Management". Press " " for more
than one second to launch the
Onscreen Display main menu to modify
its function.
Press " " to launch "Acer eView
Management".
"Acer eView Management" is for
display mode selection. Please refer to
the "Onscreen Display (OSD) Menus"
section for more details.
Acer eTimer Management
Acer ePower Management
Press " " to launch "Acer eTimer
Management".
"Acer eTimer Management" provides
the reminding function for
presentation time control. Please refer
to the "Onscreen Display (OSD) Menus"
section for more details.
Press " " to launch "Acer ePower
Management".
"Acer ePower Management"provides
you one shortcut to save the lamp and
projector’s life. Please refer to the
"Onscreen Display (OSD) Menus"
section for more details.
18
English
Main menu
Submenu
Setting
Onscreen Display (OSD) Menus
The projector has multilingual Onscreen Display (OSD) menus that allow
you to make image adjustments and change a variety of settings.
Using the OSD menus
• To open the OSD menu, press "MENU" on the control panel or remote
control.
• When the OSD is displayed, use to select an item in the main menu.
After selecting the desired main menu item, press to enter a submenu
for feature setting.
• Use to select the desired item and adjust the settings by using
.
• Select the next item to be adjusted in the submenu and adjust as described
above.
• Press "MENU" on the control panel or remote control, the screen will
return to the main menu.
• To exit the OSD menu, press "MENU" on the control panel or remote
control again. It will close and the projector will automatically save the
new settings.
English
Color
(S1110/T200/XS-S10/S1210/T210/
XS-X10/S1210Hn/S1310W/T220/
XS-W10/S1310WHn)
(S1213/T212/XS-X13/S1213Hn/
T212DT/XS-X13HG/S1313W/
S1313WHn)
19
There are many factory presets optimized for various types
of images.
Display Mode
Wall Color
Brightness
Contrast
• Bright: For brightness optimization.
• Presentation: For meeting presentation with higher
brightness.
• Standard: For common environment.
• Video: For playing video in a bright environment.
• Picture: For graphic picture.
• Game: For game content.
• Education: For education environment.
• User: Memorize user’s settings.
Use this function to choose a proper color according to the
wall. There are several choices, including White, Light
Yellow, Light Blue, Pink and Dark Green. It will
compensate the color deviation due to the wall color to
show the correct image tone.
Adjusts the brightness of the image.
• Press to darken the image.
• Press to lighten the image.
Controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast
changes the amount of black and white in the image.
• Press to decrease the contrast.
• Press to increase the contrast.
20
English
Color
Temperature
Degamma
Color R Adjusts the red color.
Color G Adjusts the green color.
Color B Adjusts the blue color.
Saturation
Adjusts the color temperature. At higher color
temperatures, the screen looks colder; at lower color
temperatures, the screen looks warmer.
Effects the representation of dark scenery. With greater
gamma value, dark scenery will look brighter.
Adjusts a video image from black and white to fully
saturated colors.
• Press to decrease the amount of color in the
image.
• Press to increase the amount of color in the
image.
Adjusts the color balance of red and green.
Tint
• Press to increase the amount of green in the
image.
• Press to increase the amount of red in the image.
Dynamic Black
(S1213/T212/XSX13/S1213Hn/
T212DT/XSX13HG/S1313W/
S1313WHn)
Note: "Saturation" and "Tint" functions are not supported under computer
mode.
If turned on, the projector dynamically adjusts the power
consumption of the lamp according to the brightness of
the image being projected. When projecting darker
images the power consumption will be reduced and the
contrast of the image will also be enhanced.
English
Image
21
• Front-Desktop: The factory default setting.
• Front-Ceiling: When you select this function, the
projector inverts the image for ceiling-mounted
projection.
Projection
Aspect Ratio
Keystone
• Rear-Desktop: When you select this function, the
projector reverses the image so that you can project
behind a translucent screen.
• Rear-Ceiling: When you select this function, the
projector reverses and inverts the image at same time.
You can project from behind a translucent screen with
ceiling mounted projection.
Use this function to choose your desired aspect ratio.
• Auto: Keeps the image with original width-height ratio
and maximizes the image to fit native horizontal or
vertical pixels.
• Full (S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn): The image will be displayed making full use
of the horizontal and vertical pixels.
• 4:3: The image will be scaled to fit the screen and
displayed using a 4:3 ratio.
• 16:9: The image will be scaled to fit the screen and
displayed using a 16:9 ratio.
• L.Box (S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn): Keeps the original signal aspect ratio and
zooms in by 1.333 times.
Adjusts image distortion caused by tilting projection (±40
degrees).
22
English
Adjusts the sharpness of the image.
Sharpness
H. Position
(Horizontal
Position)
V. Position
(Vertical
Position)
Frequency
Tracking
3D
• Press to decrease the sharpness.
• Press to increase the sharpness.
• Press to move the image left.
• Press to move the image right.
• Press to move the image down.
• Press to move the image up.
Changes the projector’s refresh rate to match the frequency
of your computer’s graphics card. If you experience a vertical
flickering bar in the projected image, use this function to
correct it.
Synchronizes the signal timing of the display with the
graphics card. If you experience an unstable or flickering
image, use this function to correct it.
• On
Select this item while using DLP 3D glasses, quad buffer
(NVIDIA/ATI...) graphics card and HQFS format file or DVD
with corresponding SW player.
3D Sync Invert
3D Warning
Message
• Off
Turns off the 3D mode.
If you see a discrete or overlapping image while wearing DLP
3D glasses, you may need to execute "Invert" to get best
match of left/right image sequence to get the correct image
(for DLP 3D).
Choose "On" to display the 3D warning message.
English
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under video mode.
Note: "Sharpness" function is not supported under computer mode.
Note: Supported 3D signal timings:
Signal source type Supported timing
VGA 640 x 480@100Hz, 640 x 480@120Hz,
HDMI (for S1210Hn/S1213Hn/
T212DT/XS-X13HG/S1310WHn/
S1313WHn)
It needs correct settings on graphics card 3D application program for correct
3D display.
The SW players, such as Stereoscopic Player and DDD TriDef Media Player
can support 3D format files. You can download these players on the web
page below.
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef3-D-Experience-4.0.2.html
800 x 600@100Hz, 800 x 600@120Hz,
1024 x 768@100Hz, 1024 x 768@120Hz
23
Note: "3D Sync Invert" is only available when 3D is enabled.
24
English
(S1110/T200/XS-S10/S1210/T210/
XS-X10/S1213/T212/XS-X13/
S1310W/T220/XS-W10/S1313W)
(S1210Hn/S1213Hn/T212DT/XSX13HG/S1310WHn/S1313WHn)
Setting
Menu Location
HDMI Color
Range
(S1210Hn/
S1213Hn/
T212DT/XSX13HG/
S1310WHn/
S1313WHn)
HDMI Scan Info
(S1210Hn/
S1213Hn/
T212DT/XSX13HG/
S1310WHn/
S1313WHn)
Closed Caption
Chooses the OSD menu location on the display screen.
Adjusts the color range of the HDMI image data to prevent
color display error.
• Auto: Automatically adjusts the color range by
information from the player.
• Limited Range: Processes the input image as limited color
range data.
• Full Range: Processes the input image as full color range
data.
Adjusts the overscan ratio of the HDMI image on screen.
• Auto: Automatically adjusts the overscan ratio by
information from the player.
• Underscan: Always no overscan on the HDMI image.
• Overscan: Always keep overscan on the HDMI image.
Selects a preferred closed captioning mode from CC1, CC2,
CC3, CC4, (CC1 displays captions in the primary language in
your area). Select "Off" to turn off the captioning feature.
This function is only available when a composite video or SVideo input signal is selected and its system format is NTSC.
English
Security
25
Security
This projector provides a useful security function for the
administrator to manage the projector.
Press to change the "Security" setting. If the security
function is enabled, your must enter "Administrator
Password" first before changing the security setting.
The factory default of "Administrator Password" is
"1234".
• Select "On" to enable the security function. You have to
enter password depending on the "Security Mode".
Please refer to "User Password" section for details.
• If "Off" is selected, you can switch on the projector
without password.
Timeout (Min.)
Once "Security" is set to "On", you can set timeout function.
• Press to select timeout duration.
• The range is from 10 to 990 minutes.
• When time is up, the projector will request you to enter
the password again.
• The factory default setting of "Timeout (Min.)" is "Off".
• Once the security function is enabled, the projector will
request you to enter password when switching on the
projector. Both "User Password" and "Administrator
Password" can be accepted for this dialogue.
User Password
• Press to set up or change "User Password".
• Use the numerical keys on the remote control to set the
password and press "MENU" to confirm.
• To delete the digits, Press .
• Enter the password again when you see "Confirm
Password" displayed.
• The password should be 4~8 digits in length.
• If you select "Request password only after plugging
• If you select "Always request password while projector
power cord", you are requested to input the password
every time the power cord is plugged.
turns on", you are requested to input the password every
time the projector is turned on.
26
English
VGA OUT
(Standby)
Administrator Password
You can enter "Administrator Password" when the "Enter
Administrator Password" or "Enter Password" dialogue box
displays.
• Press to change "Administrator Password".
• The factory default of "Administrator Password" is
"1234".
If you forget your administrator password, do the following
to retrieve the administrator password:
• Enter the unique 6-digit "Universal Password" which is
printed on the Security Card that came with your
projector. This unique password will be accepted by the
projector no matter what the administrator password is.
• If the Security Card is lost, please contact your local Acer
service center.
Selecting "On" enables the function. The projector can output
a VGA signal when it is in standby mode and the VGA IN (or
VGA IN 1) and VGA OUT sockets are correctly connected to the
devices.
Reset
Enabling this function slightly increases the standby
power consumption.
Press after choosing "Yes" to return the display
parameters on all menus to the factory default settings.
English
LAN Setting
(for S1210Hn/
S1213Hn/
T212DT/XSX13HG/
S1310WHn/
S1313WHn)
27
To connect your projector to the network:
1 Take a RJ45 cable and connect one end to the LAN input
jack of the projector and the other end to the RJ45 port.
2 Enter the LAN Setting menu. The "Enter Administrator
Password" dialogue box is displayed.
3 Enter "Administrator Password". The next level menu
is displayed.
The factory default of "Administrator Password" is
"1234". You can change it in the Setting > Security >
Administrator Password menu.
4 Select LAN in this menu and press to select "On".
5 Make sure DHCP is on, and press to select Apply and
press .
6 Re-enter the menu and note down the IP address
displayed in the row of Projector IP Address.
If your are not in a DHCP environment, set DHCP to "Off" and
contact your ITS administrator for information on Projector IP
Address, Subnet Mask, Default Gateway, and DNS Server.
LAN Reset
(for S1210Hn/
S1213Hn/
T212DT/XSX13HG/
S1310WHn/
S1313WHn)
1 Press to select Projector IP Address and press .
2 Press to move the cursor and press to
enter the digits.
3 When you finish, press MENU to save and exit the menu.
4 Repeat steps 1-3 to input addresses for Subnet Mask,
Default Gateway, DNS server.
5 Press to highlight Apply and press .
To control the projector remotely:
1 Enter the Projector IP address in the address bar of the
web browser on your computer.
2 The remote network operation page is displayed.You can
control the projector by using this page. For details, see
the notes following this table.
Press after choosing "Yes" to return all items on the Tools
page to the default settings.
28
English
To switch
input signals,
click your
desired
signal.
These buttons
function the
same as those
on the OSD
menus,
projector
control panel,
or remote
control.
See Note 2 and
Note 3.
You can
enter the
projector
information.
You can
adjust the
LAN control
settings.
You can set the
user password/
administrator
password to
prevent
unauthorized use
of the remote
network operation/
Tools page.
Note: "HDMI Color Range" is only available when the input signal is HDMI.
About LAN Setting (for S1210Hn/S1213Hn/T212DT/XS-X13HG/S1310WHn/
S1313WHn)
Note 1 : An overview of the remote network operation page
Note 2 : An overview of the Tools page
Note 3: The Info page shows the projector information and status.
English
Management
Choose "On" to dim the projector lamp, which will also
ECO Mode
High Altitude
Turn Off Mode
lower the power consumption, reduce noise, and extend
the lamp life. Choose "Off" to return to the normal mode.
Choose "On" to turn on the High Altitude mode. When
this function is turned on, the projector fans operate at full
speed continuously to cool down the projector’s
temperature.
• Instant Off: Enables you to turn off the projector
• Instant Resume: Enables you to restart the projector
29
immediately without fan cooling process by pressing
the power button twice.
immediately within 2 minutes after turning it off.
Auto Shutdown
(Minutes)
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding
Lamp Hour Reset
The projector will automatically shut down while there is
no signal input detected after the setting time.
Choose this function to show or hide warning message
when the changing lamp message is displayed. The
message will show up 30 hours before end of life.
Press after choosing "Yes" to turn the lamp hour
counter to 0 hours.
30
English
Audio
Volume
Mute
Timer
• Press to decrease the volume.
• Press to increase the volume.
• Choose "On" to turn mute on.
• Choose "Off" to turn mute off.
Timer Location Sets the location of the timer on the screen.
Timer Start (or
Stop)
Timer Period
(Minutes)
Timer Volume
Timer Display
Press to start or stop the timer.
Press to adjust the timer period.
Select this function to adjust the notification volume
when the timer function is enabled and time is up.
Press to choose a timer display mode.
English
Language
Language
31
Sets a language for the OSD menus. Use to
select your preferred language.
• Press to confirm the selection.
30
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears
onscreen
2 Partial, scrolling
or incorrectly
displayed image
(For PC (Windows
95/98/2000/XP/
Win7/Vista))
• Make sure all the cables are correctly connected as
described in the "Getting Started" section.
• Ensure none of the connector pins are bent or
broken.
• Check if the projection lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
• Make sure you have removed the lens cap and the
projector is switched on.
• Press "RESYNC" on the control panel or remote
control.
• For an incorrectly displayed image:
• Open "My Computer > Control Panel," and
then double-click the "Display" icon.
• Select the "Settings" tab.
• Verify that your display resolution setting is
lower than or equal to 1600 x 1200, 1920 x
1080.
• Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
• Verify that the resolution setting is lower than
or equal to 1600 x 1200, 1920 x 1080.
• Click the "Change" button under the
"Monitor" tab.
• Click "Show all devices > Standard monitor
types" under the SP box, and choose the
resolution mode you need under the "Models"
box.
• Verify that the resolution setting of the
monitor display is lower than or equal to 1600
x 1200, 1920 x 1080.
31
English
3 Partial, scrolling
or incorrectly
displayed image
(For notebooks)
4 The screen of the
notebook
computer is not
displaying your
presentation
5 Image is unstable
or flickering
• Press "RESYNC" on the control panel or remote
control.
• For an incorrectly displayed image:
• Follow the steps for item 2 (above) to adjust
the resolution of your computer.
• Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
• If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
• If you are using a Microsoft
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
• If you are using an Apple
notebook: In System Preferences, open Display and
select Video Mirroring "On."
®
Windows® based
®
Mac® OS based
• Use "Tracking" to correct it. Refer to the "Image"
section for more information.
• Change the display color setting on your computer.
6 Image has vertical
flickering bar
7 Image is out of
focus
• Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
• Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
• Make sure the lens cap is removed.
• Adjusts the focus ring on the projector lens.
• Make sure the projection screen is within the
required distance:
S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/
S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG: 1.32
to 12 feet (0.4 to 3.7 meters)
S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn: 0.98 to 10.5 feet (0.3 to 3.2 meters)
Refer to the "How to Get a Preferred Image Size by
Adjusting Distance and Zoom" section for more
information.
32
English
8 Image is stretched
when displaying a
"widescreen"
DVD title
9 Image is too small
or too large
10 Image has slanted
sides
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
• If you play a 4:3 format DVD title, please change the
format to 4:3 with the projector OSD.
• If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
• Adjust the zoom lever on the top of the projector.
• Move the projector closer to or further from the
screen.
• Press "MENU" on the control panel or remote
control. Go to "Image" > "Aspect Ratio" and try
different settings.
• If possible, reposition the projector so that it is
centered on the screen and below the bottom of the
screen.
• Press the Keystone correction keys on the control
panel or remote control until the image becomes
square.
• Press "MENU" on the control panel or remote
control to open the OSD menu. Go to "Image" >
"Keystone" to make adjustments.
11 Image is reversed
• Select "Image" > "Projection", "Image" >
"Projection Location" on the OSD and adjust the
projection direction.
Problems with the Projector
# Condition Solution
1 The projector stops responding
to all controls
2 Lamp burns out or makes a
popping sound
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
English
OSD Messages
Fan Fail.
Lamp will automatically turn off soon.
Projector Overheated.
Lamp will automatically turn off soon.
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it is used. Please also check the dust filters if
they are installed. If the dust filter is clogged with dust, please
clean it.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
33
34
English
LED & Alarm Definition Listing
LED Messages
Message Power LED LAMP LED TEMP LED
Red Blue Red Red
Standby
(Power cord plugged in)
Power on -- V -- --
Lamp retry -- Quick
Turning off (Cooling
state)
Turning off (Cooling
completed)
Error (Thermal failure) -- V -- V
Error (Fan lock failure) -- V -- Quick
Error (Lamp breakdown) -- V V --
Error (Color wheel
failure)
V-- -- --
-- --
flashing
Quick
flashing
V-- -- --
-- V Quick
-- -- --
flashing
--
flashing
35
English
1
8
1
2
8
7
8
6
5
4
3
1
2
1
5
8
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life itself. It will show you a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooled down for at least 45
minutes before changing the lamp.
Warning: Lamp compartment is hot! Allow it to cool down before
changing lamp!
To remove the lamp:
1 Turn the projector off by pressing (POWER).
2 Allow the projector at least 45 minutes to cool down.
3 Disconnect the power cord.
4 Use a screwdriver to remove the screws from the cover. (Illustration #1)
5 Push up and remove the cover.
6 Remove and dispose of the lamp protection film (Illustration #2).
7 Remove the lamp connector from the projector and the screw that secures
the lamp module (Illustration #3).
8 Lift the handle so that it stands up. Pull out the lamp module by force
(Illustration #4).
To replace the lamp module, use a new lamp and follow illustrations # - # .
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
36
English
20
mm
13
mm
8.4
mm
130 mm
49.9
mm
Short Rod
Screw Type A
50 mm length / 8 mm diameter -
Ceiling Mount Base
- Attach to ceiling
Long Rod
Extension Rod
Allen Key
- For tighten/loosen
Tightening Screw
Medium Rod
Large Cylinder Cap
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of cylinder screws.
37
English
Large Washer
Projector Bracket
Supports projector and
allows for adjustments
Screw Type B
Spacer
- For heat dissipation
Screw Type A
50 mm length /8 mm diameter
Large Cylinder Cap
Allen Key
- For tighten/loosen
Tightening Screw
3 Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4 Attach the ceiling bracket to the ceiling rod.
38
English
Allen Key
Tightening Screw
Allen Key
Tightening Screw
96.09 mm
149.90 mm
18.46 mm
83.27 mm
12.11 mm
34.26 mm
5 Adjust the angle and positioning as necessary.
30
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models Screw Type B Washer Type
Diameter (mm) Length (mm) Large Small
S1110/T200/XS-S10/
S1210/T210/XS-X10/
S1210Hn/S1213/T212/XSX13/S1213Hn/T212DT/
XS-X13HG/S1310W/T220/
XS-W10/S1310WHn/
S1313W/S1313WHn
325VV
English
Specifications
The specifications below are subject to change without notice. For final specs,
please refer to Acer's marketing documentation.
39
Projection system
Resolution
™
DLP
• S1110/T200/XS-S10:
Native: SVGA (800 x 600)
Maximum: UXGA (1600 x 1200), 1080p (1920 x 1080)
• S1210/T210/XS-X10/S1210Hn/S1213/T212/XS-X13/
S1213Hn/T212DT/XS-X13HG:
Native: XGA (1024 x 768)
Maximum: UXGA (1600 x 1200), 1080p (1920 x 1080)
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn:
Native: WXGA (1280 x 800)
Maximum: UXGA (1600 x 1200), 1080p (1920 x 1080)
Computer compatibility Refer to the "Compatibility Modes" section for more
information.
Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/K/K1/L),
HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i,
576i)
Aspect ratio
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/
T212/XS-X13/S1213Hn/T212DT/XS-X13HG:
Auto, 4:3 (native), 16:9
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn:
Auto, 4:3, 16:9, Full, Letter Box
Displayable colors 1.07 billion colors
Projection lens F = 2.6, f = 6.9 mm, Manual Focus
Projection screen size
(diagonal)
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/
T212/XS-X13/S1213Hn/T212DT/XS-X13HG:
40" (102 cm) - 299" (759 cm)
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn:
47" (119 cm) - 568" (1143 cm)
Projection distance
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/S1213/
T212/XS-X13/S1213Hn/T212DT/XS-X13HG:
1.32' (0.4 m) - 12' (3.7 m)
• S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn:
0.98' (0.3 m) - 10.5' (3.2 m)
Throw ratio 81" +
Horizontal scan rate 31 - 99 kHz
Vertical refresh scan rate 48 - 120 Hz
Keystone correction +/-40 Degrees (Vertical), Manual
Digital zoom 1 X
Audio 2W x 1
Weight Approximate 2.7 kg (5.95 lbs.)
Dimensions (W x D x H) 272 x 228.5 x 103.5 mm (10.7" x 9.0" x 4.1")
Power supply Universal AC input 100 - 240 V, input frequency 50/60 Hz
3% @ 1 m
40
English
Power consumption
(typical)
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/
S1310W/T220/XS-W10/S1310WHn:
240 W
• S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG/
S1313W/S1313WHn:
285 W
Power consumption
(standby)
• S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/
S1310W/T220/XS-W10/S1310WHn:
< 1 W
• S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG/
S1313W/S1313WHn:
< 0.5 W
Operating temperature 0ºC to 35ºC / 32ºF to 95ºF
I/O connectors
• Power socket x 1
• RS232 x 1
• VGA input x 1
• Composite video x 1
• S-Video x 1
• 3.5 mm audio jack input x 1
• 3.5 mm audio jack output x 1
• VGA output x 1
• USB x 1 (Type mini B)
Standard package contents
Accessory (optional)
Below items are for S1213/T212/XS-X13/S1313W only.
3.5 mm audio jack input x 2
•
• Audio input (R/L) x 1
Below items are for S1210Hn/S1213Hn/T212DT/XSX13HG/S1310WHn/S1313WHn only.
HDMI 1.3 input x 1
•
• 3.5 mm audio jack input x 2
• RJ45 LAN input x 1
• Audio input (R/L) x 1
• AC power cord x 1
• VGA cable x 1
• Remote control x 1
• Battery x 2 (for the remote control)
• User's guide (CD-ROM) x 1
• Quick start guide x 1
• Security card x 1
• Composite video cable x 1
• Carrying case x 1
• Dust filter x 1
* Design and specifications are subject to change without notice.
English
Compatibility Modes
1 VGA Analog - PC Signal
Mode Resolution V.Frequency [Hz]
VGA_60
VGA_72 72.809 37.861
VGA_75 75 37.5
VGA_85 85.008 43.269
VGA_120 119.518 61.91
SVGA_56
SVGA_60 60.317 37.879
SVGA_72 72.188 48.077
SVGA_75 75 46.875
SVGA_85 85.061 53.674
SVGA_120 119.854 77.425
XGA_60
XGA_70 70.069 56.476
XGA_75 75.029 60.023
XGA_85 84.997 68.677
XGA_120 119.804 98.958
SXGA_70
SXGA_75 75 67.5
SXGA_85 1152 x 864 84.99 77.094
SXGA_60
SXGA_72 72 76.97
SXGA_75 75.025 79.976
SXGA_85 85.024 91.146
QuadVGA_60
QuadVGA_75 75 75
SXGA+_60 1400 x 1050 59.978 65.317
UXGA_60 1600 x 1200 60 75
Mac G4 640 x 480@60Hz 59.94 31.469
MAC13 640 x 480@67Hz 66.667 35
Mac G4 800 x 600@60Hz 60.317 37.879
Mac G4 1024 x 768@60Hz 60.004 48.363
MAC19 1024 x 768@75Hz 75.02 60.241
MAC21 1152 x 870@75Hz 75.061 68.681
640 x 480
800 x 600
1024 x 768
1152 x 864
1280 x 1024
1280 x 960
59.94 31.469
56.25 35.156
60.004 48.363
70.012 63.851
60.02 63.981
60 60
41
H.Frequency
[KHz]
42
English
WXGA_60
WXGA_75 74.893 60.289
WXGA_85 84.837 68.633
WXGA_60 1280 x 720 60 45
WXGA_60 1280 x 800 59.81 49.702
WXGA+_60 1440 x 900 59.887 55.935
1680x1050_60 1680 x 1050 59.954 65.29
1920x1080-RB 1920 x1080 60 66.6
1920x1080-EIA 1920 x1080 60 67.5
acer_16:9 1366 x 768 59.79 47.712
acer_timing 1024 x 600 60 37.5
1280 x 768
59.87 47.776
2 HDMI - PC Signal (For S1210Hn/S1213Hn/T212DT/XS-X13HG/
S1310WHn/S1313WHn)
Mode Resolution V.Frequency [Hz]
VGA_60
VGA_72 72.809 37.861
VGA_75 75 37.5
VGA_85 85.008 43.269
VGA_120 119.518 61.91
SVGA_56
SVGA_60 60.317 37.879
SVGA_72 72.188 48.077
SVGA_75 75 46.875
SVGA_85 85.061 53.674
SVGA_120 119.854 77.425
XGA_60
XGA_70 70.069 56.476
XGA_75 75.029 60.023
XGA_120 119.804 98.958
SXGA_75
SXGA_85 84.99 77.094
SXGA_60
SXGA_72 72 76.97
SXGA_75 75.025 79.976
SXGA_85 85.024 91.146
QuadVGA_75 1280 x 960 75 75
SXGA+_60 1400 x 1050 59.978 65.317
640 x 480
800 x 600
1024 x 768
1152 x 864
1280 x 1024
59.94 31.469
56.25 35.156
60.004 48.363
75 67.5
60.02 63.981
H.Frequency
[KHz]
English
UXGA_60 1600 x 1200 60 75
Mac G4 640 x 480@60Hz 59.94 31.469
MAC13 640 x 480@67Hz 66.667 35
Mac G4 800 x 600@60Hz 60.317 37.879
Mac G4 1024 x 768@60Hz 60.004 48.363
MAC19 1024 x 768@75Hz 75.02 60.241
MAC21 1152 x 870@75Hz 75.061 68.681
WXGA_60
WXGA_75 74.893 60.289
WXGA_85 84.837 68.633
WXGA_60 1280 x 720 60 45
WXGA_60 1280 x 800 59.81 49.702
WXGA+_60 1440 x 900 59.887 55.935
1680x1050_60 1680 x 1050 59.954 65.29
acer_16:9 1366 x 768 59.79 47.712
1920x1080_RB 1920 x1080 60 66.587
1920x1080_EIA 1920 x1080 60 67.5
acer_timing 1024 x 600 60 37.5
1280 x 768
59.87 47.776
43
3 HDMI - Video Signal (For S1210Hn/S1213Hn/T212DT/XS-X13HG/
S1310WHn/S1313WHn)
Mode Resolution V.Frequency [Hz] H.Frequency [KHz]
480i
480p 720 x 480 60 31.47
576i
576p 720 x 576 50 31.25
720p 1280 x 720 60 45.00
720p 1280 x 720 50 37.50
1080i 1920 x 1080 60 33.75
1080i 1920 x 1080 50 28.13
1080p 1920 x 1080 60 67.50
1080p 1920 x 1080 50 56.26
1080p 1920 x 1080 24 27.00
1080p 1920 x 1080 23.98 26.97
720 x 480
(1440 x 480)
720 x 576
(1440 x 576)
60 15.73
50 15.63
4 YPbPr Signal
Mode Resolution V.Frequency [Hz] H.Frequency [KHz]
480i
480p
576i
720 x 480
720 x 480
720 x 576
59.94 15.73
59.94 31.47
50.00 15.63
44
English
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
50.00 31.25
60.00 45.00
50.00 37.50
60.00 33.75
50.00 28.13
60.00 67.5
50.00 56.26
24.00 27.00
23.98 26.97
5 Video, S-Video Signal
Mode V.Frequency [Hz] H.Frequency [KHz] fsc (MHz)
NTSC 15.73 60
PAL 15.63 50
SECAM 15.63 50
PAL-M 15.73 60
PAL-N 15.63 50
3.58
4.43
4.25 or 4.41
3.58
3.58
PAL-60 15.73 60
NTSC4.43 15.73 60
4.43
4.43
English
Regulations and safety notices
45
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
English
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
46
English
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby, declares that this projector series is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
47
English
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact a local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
English
48
English
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:ru_jan@acer.com.tw
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it
Hereby declare that:
Product: Projector
Trade Name: Acer
Model Number: QSV1101/QNX1102/QNX1105/QWX1103 series
Machine Type: S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/
S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG/
S1310W/T220/XS-W10/S1310WHn/S1313W/S1313WHn series
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
Acer Incorporated
New Taipei City 221, Taiwan
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that production
units of the same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized standards:
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN61000-3-2 Class A
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following harmonized
standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in
Electrical and Electronic Equipment
-. The maximum concentration values of the restricted substances by weight in homogenous
material are:
Lead 0.1% Polybrominated Biphenyls (PBB’s) 0.1%
Mercury 0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
Hexavalent Chromium 0.1% Cadmium 0.01%
Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
English
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
The standards listed below are applied to the product if built with WLAN module or wireless
keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard:
• Article 3.1(a) Health and Safety
-. EN60950-1
-. EN62311
• Article 3.1(b) EMC
-. EN301 489-1
-. EN301 489-17
49
English
• Article 3.2 Spectrum Usages
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2012.
RU Jan/Sr. Manager Date
Regulation Center, Acer Inc.
April. 02, 2012 -
50
English
Product: DLP Projector
Model Number: QSV1101/QNX1102/QNX1105/
QWX1103 series
Machine Type: S1110/T200/XS-S10/
S1210/T210/XS-X10/S1210Hn
S1213/T212/XS-X13
S1213Hn/T212DT/XS-X13HG/
S1310W/T220/XS-W10/S1310WHn/
S1313W/S1313WHn series
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Loading...