Page 1
PC2120
All-in-One 12.1” TFT LCD
User’s Manual
Panel PC
Page 2
Disclaimers
The information in this manual has been carefully checked and is
believed to be accurate. ACNODES assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
ACNODES assumes no responsibility for any inaccuracies that may be
contained in this document. ACNODES makes no commitment to update or to
keep current the information contained in this manual.
ACNODES reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
ACNODES
Copyright 2004 by AC NO DE S
All rights rese rved.
September 2004, Version A1
Printed in Taiw an
ii
Page 3
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
z
Reorient or relocate t he receiving anten na.
z
Increase the separation between the equipment and
receiver.
z
Connec t the equ ipment int o an outlet on a circu it
different from th at to which the receiver is connected.
z
Consult the dealer or an experienced radio/TV technician
for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Page 4
Safety Precautions
Be fo re g et ti ng s ta rt ed, re ad t he f ol lowi ng i mp orta nt c au ti ons.
1. The PC 2120 series does not come equipped with an
operating system. An operating system must be loaded
first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any
static-shielded devices. Most electronic components are
sensitive to static electrical charge.
3. Disconnect the power cord from the PC 2120 series before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the PC 2120
series is properly grounded.
4. The brightness of the flat panel display decreases with
usage. However, hours of use vary depending on the
application environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The PC 2120 series may come
with or w/o a touchscreen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touchscreen, you
must follow the same procedure and not spray any
cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or
vibration. When assembling the PC 2120 series, make
sure it is securely installed.
iv
Page 5
8. Do not open the system’s back cover. If opening the
cover for maintenance is a must, only a trained
technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge,
observe the following precautions:
9
Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
9
When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
ACNODES is a trademark of ACNODES ALi
is a trademark of Acer Laboratories, Inc.
AMD is a trademark of Advanced Micro Devices, Inc.
AMI is a trademark of American Megatrends, Inc.
Cyrix is a trademark of Cyrix Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft
Corporation.
SMC is a trademark of Standard Microsystems Corporation.
C&T is a trademark of Chips and Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
VIA is a trademark of VIA Technologies, Inc.
Other brand names and tradem arks are the properties of their
respective owners.
v
Page 6
Table of Contents
Chapter 1 Introduction.....................................................1
1.1 General Description ................................................1
1.2 Specifications..........................................................2
1.2.1 Core System for PC 2120 series system with
SBC85610VE ........................................................................ 2
1.2.2 System I/O outlet .................................................... 2
1.2.3 Built-in Peripherals .................................................. 3
1.2.4 Net Weight ............................................................... 3
1.2.5 12.1" TFT LCD Specification..................................... 4
1.2.6 Environmental ......................................................... 4
1.2.7 Dimension (main body size) .................................. 4
1.3 Utilities Supported ..................................................4
1.4 Dimensions..............................................................5
1.5 I/O Outlets ................................................................6
Chapter 2 System Configuration ...................................9
2.1 Pedestal Versatility .................................................9
2.1.1 Desktop Standing.................................................. 10
2.1.2 Vertical Wall Mounting ......................................... 11
2.1.3 Wall Mounting ....................................................... 12
2.1.4 30o Table Standing ................................................ 14
Chapter 3 Hardware Installation .................................15
3.1 CPU ......................................................................16
3.2 DRAM .....................................................................16
3.3 HDD
......................................................................16
3.4 Three Serial Ports .................................................18
3.5 Parallel Port ...........................................................18
3.6 VGA
......................................................................19
3.7 Ethernet..................................................................19
3.8 Cash Drawer (PC 2120-610e only) ........................20
vi
Page 7
3.9 Keyboard and Mouse............................................20
3.10 Expansion Slot ....................................................21
3.11 USB and Dallas Key Installation ........................22
3.12 System O/S and Software Installation...............22
Appendix A Power Supply Specifications ................23
Appendix B System Configuration Limitation Notice
...............................................................................................25
vii
Page 8
This page does not contain any information.
viii
Page 9
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
C h a p t e r 1
Introduction
This chapter contains the general information and detailed
specifications of PC 2120 series. Chapter 1 includes the following
sections:
z
General Description
z
System Specification
z
Utilities Supported
z
Dimensions
z
I/O Outlets
1.1 General Description
The PC 2120 series super slim industrial panel PCs are mainly
designed for industrial automation and some space-constricted
embedded applications. For some space-concerned industries, a
traditional PC with a separate main system, display monitor and
keyboard is simply not integrated enough.
Ruggedly designed, the PC 2120 series is 100% IBM PC/AT
compatible and it integrates super I/Os, 12.1” TFT touch screen,
Ethernet, and packs special industrial features like watchdog timer all
in a single system. The full PC functionality coupled with its
industrial-grade construction easily tailors the system for any
embedded applications -- allowing the system to endure continuous
operation in any hostile industrial environments where stability and
reliability is a must.
The PC 2120 series feature a versatile stand suited for a wide variety
of applications. W ith the pedestal kit assembled to the main unit, both
can transform into different positions such as desktop free standing,
30° table standing, panel mount and wall mounting. Its cable
management device also trims the operation environment. The NEMA
4/12 water/dust-proof front panel is specially designed for the
continuous operation in outdoor environments. Common applications
of these PANEL PCs include POS, POI terminals, Hospitality.
Introduction
1
Page 10
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
Designed by the PC experts for PC professionals, the PC 2120 series
are virtually the ultimate one-step solution for your space-limited
applications.
1.2 Specifications
1.2.1 Core System for PC 2120 series system with
SBC85610VE
z
CPU:
Socket370 for Intel Celeron/Pentium III and VIA C3
processor
z
System Chipset:
VIA VT8601T, VT82C686B with integrated real-time clock
z
BIOS:
Phoenix-Award BIOS, 4M bit with RPL/PXE LAN Boot ROM
z
System Memory:
Two 168-pin DIMM Socket Maximum of 1GB SDRAM
z
Watchdog Timer:
Generates a system reset or NMI by jumper selectable;
software programmable Time interval; 64 levels, 0.5~8 /
5~80 / 50~800 / 100~1600 seconds
1.2.2 System I/O outlet
z
Standard I/O:
„
Page 11
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
„
z
z
z
4 x USB ports
„
1 x LAN
„
1 x dallas key(option)
„
2 x RJ-11 cash drawer ports (610e only)
Cash Drawer Port:
RJ-11 cash drawer x 2 (610e only)
Ethernet:
„
Realtek 8139C PCI Bus 10/100M Base-T
„
Wake-On-LAN
„
RJ-45 interface equipped
VGA/Flat Panel Controller:
„
VIA VT8601T chip with integrated Trident 2D/3D accelerator
„
2/4/8 MB frame buffer sharing system memory
„
LCD/Simultaneous mode:
1024x768 @ 16bpp (60Hz)
„
CRT mode:
1024x768 @ 16bpp (85Hz)
1.2.3 Built-in Peripherals
z
AT80W power supply(PW-080A-03Y)
z
3.5” Hard disk drive bay
z
3M 12.1” resistive 8-wire FG Touch Screen(R812.112)
with RS-232(COM3)
z
System cooling fan
z
Dallas key(option)
1.2.4 Net Weight
z
PC 2120 series: 4.2 Kgs
Introduction
3
Page 12
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
1.2.5 12.1" TFT LCD Specification
z
Display area 245(H)x184(V)(12.1" diagonal)
z
Resolution 1024×768 (XGA)
z
Pixel pitch 0.240(H)x0.240(V)(TYP.)
z
Contrast Ratio 200 (MIN.)
z
Average Luminance 150cd/m²(TYP.)
z
Viewing Angle θL(40 )θR(40)ΦH(10)Φ
L
(30)
1.2.6 Environmental
z
Operating Temperature Range: 0
z
Relative Humidity: 20% ~ 85%; non-condensing
z
EMC: FCC
z
Safety: CE
o
C ~ 40oC
1.2.7 Dimension (main body size)
z
PC 2120 series: 360 x 277 x 81.2 mm (WxHxD)
NOTE1
For more detailed information on the system engine bo
used in your PANEL PC, refer to the system board Us
Manual that came with the system packaging.
ard
er’s
NOTE2 In order to avoid system over load, therefore a system
power limitation list is necessary to limit power load of
key parts and user’s devices. For more detailed
information on the Appendix B System Configuration
Limitation Notice
1.3 Utilities Supported
z
Watchdog Utility
z
Ethernet Utility
z
VGA Drivers
z
Touchscreen Utility(3M 8-wire)
.
4 Introduction
Page 13
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
1.4 Dimensions
Introduction
5
Page 14
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
1.5 I/O Outlets
The following figure shows the I/O arrangement of the PC 2120 series.
PC 2120-610/ 610e Side View
1 2XUSB ports 2 Dallas Key (option)
6 Introduction
Page 15
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
PC 2120-610 Bottom View
PC 2120-610e Bottom View
3 2x USB ports 9 LAN port
2x cash drawer ports
4
(PC 2120-610e only)
10 COM1 p ort
5 COM4 port 11 COM2 p ort
PCI expansion slot
6
outlet
12 printer port
7 mouse 13 VGA port
8 keyboard 14 power switch ON/OFF
Introduction
7
Page 16
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
This page does not contain any information.
8 Introduction
Page 17
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
C h a p t e r 2
System Configuration
This chapter details the system parts and components with figures.
Sections include:
z
System Major Parts
z
Pedestal Versatility
z
System Key Components
2.1 Pedestal Versatility
The PC 2120 series features a versatile stand designed for various
environmental applications. A complete set of pedestal is provided to
make up the various stands.
System Configuration
9
Page 18
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
2.1.1 Desktop Standing
The standard kit that makes up a free-standing computer include:
1 System main body 4
Cable management
2
shroud
3 Pedestal 6 Small hinge caps
Small back metal
fixtures
5 Main prop
By assembling these components to the main body of PC 2120 series,
the computer stands on the table as an independent unit. This
space-saving com puter is commonly adapted for office automation,
video conference and hotel information counter. The unit after proper
assembly would look as illustrated below.
10 System Configuration
Page 19
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
2.1.2 Vertical Wall Mounting
For panel mounting only a set of mounting kit is needed, there is no
pedestal kit or cable management shroud required. Please refer to the
following figures.
System Configuration
11
Page 20
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
2.1.3 Wall Mounting
The standard kit that makes up a wall-mount unit includes:
1. System main body
2. Cable management shroud
3. Small back metal fixtures
4. Main prop
5. Rubber slip:
The rubber slip has to be inserted to the top opening of
the main prop to make the whole unit look complete and
integrated.
6. Small hinge caps
7. Metal mounting kit
During assembling, the main prop has to be rotated 90° and
screwed to the system’s main body by the back metal fixture.
Page 21
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
By assembling these accessories to the main body of the PC 2120
series, the computer is mounted and forms a 30° angle to the wall as
illustrated below. Such unit is commonly used in medical
instrumentation, stand-alone POI system.
Page 22
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
2.1.4 30o Table Standing
For a 30o table-standing use, only the standard set of mounting kit is
needed, there is no pedestal kit or cable management shroud
required. The standard kit m aking up a 30o table-standing unit
includes:
1. System main body
2. Cable management shroud
3. Large back metal fixtures
4. Large hinge caps
5. Main prop
6. Rubber Slip:
When the system is to be assembled as a 30
table-standing unit, the rubber slip has to be inserted to
the front opening of th e laid-down main prop t o make
the whole unit look complete and integrated.
14 System Configuration
o
Page 23
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
C h a p t e r 3
Hardware Installation
This chapter describes the installation and the cable connection to the
system connectors. See system board User’s Manual that came with
your PANEL PC packaging for more details. Sections in this chapter
includes:
z
CPU
z
DRAM
z
HDD
z
3 x Serial Ports
z
Parallel Port
z
VGA
z
Ethernet
z
Keyboard
z
PS/2 Mouse
z
Cash Drawer(610e only)
z
Dallas Key(option)
z
Expansion Slot
z
System O/S and Software Installation
The PC 2120 series has either a Pentium or a Pentium III/Celeron little
board with a free PCI slot inside and a 3.5” HDD drive bay. These
come as standard configuration of the system. Upgrading to a higher
performance CPU, higher capacity DRAM modules and hard disk
drive can increase system performance. The user can use the I/O
ports located at the bottom layer of the chassis to connect external
peripheral devices, such as a m onitor, serial devices, parallel
printer…etc.
If you encounter difficulties during connection, loosen the screws on
the cable management shroud, then remove the shroud for easy
peripheral connection.
NOTE:
Hardware Installation
Make sure th
ins
t
alla
tion. To
and HDD,
metal rear bracket first.
e power cor
ins
t
all a
take out the p
d is disconnected before any
ny in
t
e
rnal device s
l
astic rear cover and unscrew the
uch as
CPU, DRAM
15
Page 24
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.1 CPU
The standard PC 2120 series solely uses a Pentium III/Celeron-grade
supported CPU card (SBC85610VE). In further classifying the CPU
cards of the other systems.
3.2 DRAM
The PC 2120 series system control board, SBC85610VE, provides 2 x
168-pin DIMM supporting system memory up to 1GB.
3.3 HDD
The standard packing will reserve a 3.5” hard disk drive bay. If the
user intends to install or remove the device for repair or for a
higher-capacity one, then follow the installation instructions and
diagram below.
1. Product Finished.
2. There are 19 screws that fasten the rear cover on to the
main unit. Take out the screws and pull out the rear
cover.
3. To remove the VEA bracket, loosen and take off the 5
screws (2 on each side) that bolts the bracket to the
main unit.
4. loosen and take off the 3 screws (2 on each side) that
bolts the
5. To remove the HDD bracket and Riser card.
6. Loosen and take off the 7 screws (2 and 3 on each side)
that bolts the bracket to t he main unit.
7. Repeat step2 to step6 for assembling.
16 Hardware Installation
Page 25
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
Hardware Installation
17
Page 26
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.4 Three Serial Ports
The PC 2120 series provides three onboard serial ports installed on
the bottom rear side of the chassis. Arrangements on PC 2120 series
specify COM1, COM4 providing RS-232 interface, and with its
RS-422/485 interface connected to COM2. Each serial port comes
with +5V/+12V power capabilities on both Pin 1 and Pin 9, ready to
accommodate a wide array of serial devices such as fax modem,
scanner, serial mouse, touch screen...etc. If the touch screen option is
included, its controller will share COM3.
1
2 3 4 5
6
7 8 9
Pin #
1 TX- DATA-
2 TX+ DATA+
3 RX+ No connector
4 RX- No connector
5 GND GND
6 No connector No connector
7 No connector No connector
8 No connector No connector
9 No connector No connector
3.5 Parallel Port
The printer interface is a 25-pin D-SUB connector located at the
bottom side. To connect any parallel device, just plug in the device
connector to the 25-pin D-SUB.
Signal Name
R2-422 RS-485
18 Hardware Installation
Page 27
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.6 VGA
The PC 2120 series has an analog RGB interface connector installed
on the bottom side. It is able to connect to an expansion CRT monitor,
and the system can display on both the flat panel and the CRT
simultaneously.
Since the PC 2120 series adapts a flat panel with a resolution of 1024
x 768, simultaneous support of a CRT monitor requires the setting of
the CRT’s VGA resolution to 1024 x 768 too. The connection to a
CRT monitor is also an easy plug-in of the CRT connector to the RGB
interface.
3.7 Ethernet
The PC 2120 series provides an NE2000 compatible Ethernet (RJ-45)
interface. For network connection, just plug in one cable end of a
10-Base-T Hub or 100-Base-T Hub into the standard Ethernet phone
jack. The pin assignment of the RJ-45 is listed below;
1
2 3 4 5 6 7 8
RJ-45
RJ-45 Connector Pin Assignment
Pin Description
1 Tx+ (Data transmission positive)
2 Tx- (Data transmission negative)
3 Rx+(Data reception positive)
6 Rx- (Data reception negative)
others Not use
Hardware Installation
19
Page 28
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.8 Cash Drawer (PC 2120-610e only)
The PC 2120-610e provides two cash drawer port. It can be used to
control the opening and closing of the cash drawer on a POS system.
The cash drawer Jack is follower Epson cash drawer spec. pin
position and pin assignment are shown below.
DRW2
DRW1
P1
P1
PC 2120-610e Cash Drawer Pin Assignment
Pin DRW1 DRW2
P1 FG(GND) FG(GND)
P2 Drawer SOL-1 Drawer SOL-2
P3 Drawer SW-1 Drawer SW-2
P4 +24V +24V
P5 N/A N/A
P6 GND GND
3.9 Keyboard and Mouse
The PC 2120 series provides a standard PS/2 keyboard and a PS/2
mouse connector located at the bottom of panel.
20 Hardware Installation
Page 29
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.10
Expansion Slot
The PC 2120 series can be equipped with or without any expansion
slot. As for the PC 2120 series, this comes as a standard system
feature. If the system comes with expansion capability, then the
system includes a PCI expansion riser card to accommodate a PCI
device at a given time. Due to the internal space limitation, only a
half-size expansion card can be adapted. To use the PCI expansion,
refer to the following figure and follow the installation instructions
below;
Plug a PCI card into the PCI slot on the riser card and fix all
connectors of the expansion card will come out from the expansion
outlet on the bottom side of the chassis for further cable connection.
z
Unscrew the metal slip located inside the expansion
outlet.
z
Plug the riser card into the onboard PCI slot first.
z
Screw the metal opening to the power supply bracket
and the multi-I/O conversion metal piece.
z
Plug a PCI card int o the PCI slot on the riser card and
screw the expansion card to the metal front
compartment. All the connectors of the expansion card
will come out from the opening on the rear cover for
further cable connection.
z
Screw the rear cover to the chassis.
Please also note that the total height of the system with expansion
slot is 93 mm.
Hardware Installation
21
Page 30
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
3.11 USB and Dallas Key Installation
To install an USB device or to access a Dallas key to the system from
side panel, you must get access to the connectors located on the side
panel. Take off the dust/spill cap located at the side panel by pushing
it downward to loosen its grip on top. Once loosened, pull the cap
upward to disengage completely.
3.12 System O/S and Software Installation
The PC 2120 series is not equipped with any operating system. It
reserves a 3.5” HDD drive bay for its storage device space. As both
devices are built in the system chassis, to load any O/S or application
software into the computer, an external device is needed to act as a
bridge. There are three major ways to load software into the system.
z
Use an external USB flash memory:
Attach a USB flash memory to the USB port. Then,
configure the system BIOS setup and containing
necessary software and start the installation.
z
Use Ethernet:
If the Ethernet bootrom is already included in the system,
the user can boot u p the system via bootrom and
download the system O/S or application software from
the net.
z
Use external USB CD-ROM/ HDD:
Attach a USB CD-ROM or USB HDD to the USB port. Then,
configure the system BIOS setup and containing
necessary software and start the installation.
22 Hardware Installation
Page 31
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
A p p e n d i x A
Power Supply Specifications
Introduction
The power supply used in the PC 2120 series is an AT 80W open
frame power supply. The specifications and features of this special
power supply are listed in the following sections.
Specifications
z
AT 80W output
z
Input voltage 90~132VAC (MIN.) 180~264VAC (MAX.)
z
Over voltage, over load protection
z
Continuous short circuit protection
z
Conductive EMI meets F CC class B
Input Requirements
Description MIN. TYP. MAX. Condition
Input Voltage 90~132V 115/230V 180~264V 47/63Hz
Input Current - - 2A 115V/50Hz
Line Freq. 47Hz 50/60Hz 63Hz -
Inrush Current - 50A Cold Start
Efficiency - 65% -
Power Supply Specifications
115V at full
load
23
Page 32
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
Output Characteristic
z
Static DC load, Ripple and Noise
Nominal
Voltage
Total
Regulation
Output Current
Ripple &
+5V +5% 0.8A~8A 50mV
+12V +8% 0.3A~3A 120mV
-12V +10% 0.03A~0.3A 150mV
z
Hold-up time: 10ms at least.
z
Over voltage protection: Fr om +5.6VDC to 6.5VDC
z
Short circuit protection: Conti nuous
Noise
Environmental Specifications
z
Operating temperature range: 0
z
Storage temperature range: -10
z
Humidity, non-condensing: 10% ~ 90%
z
MTBF:
°
C to 50°C
°
C to +70°C
80000hours min. at max. load for 25°C ambient
temperature
International Standards
EMI Standards(meet)
z
FCC Requirements
The power supply shall comply with the FCC”Class B”
conducted
z
CE Requirements
The power supply shall confirm to meet the ”Class B”
requirements of EN55022
24 Power Supply Specifications
Page 33
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
A p p e n d i x B
System Configuration Limitation Notice
Processor Limitation List
For over all, the CPU power consumption must be under
+5V@5.9A/+12V@1.0A
System Configuration Limitation Notice
Processor Power Consumption Recommend
Celeron-850E +5V@6.37A/+12V@0.41A NO
Celeron-1.2G/256K
(Tualatin)
Pentium III-850E +5V@6.15A/+12V@0.45A NO
PentiumIII-1.13G/256K
(Tualatin)
Pentium
III-1.26G/512K(Tualatin)
VIA C3-800MHz(133) +5V@4.53A/+12V@0.40A YES
VIA C3-1000MHz(133) +5V@4.8A/+12V@0.40A YES
VIA C3-1200MHz(133) +5V@5.2A/+12V@0.40A YES
+5V@5.56A/+12V@0.45A YES
+5V@5.45A/+12V@0.42A YES
+5V@6.17A/+12V@0.42A NO
25
Page 34
PC 2120 All-in-One 12.1” TFT LCD Panel PC User’s Manual
PC 2120-610 Configuration Limitation List
PC 2120-610e Configuration Limitation List
Parts Power Consumption Remark
Processor Refer to Processor Limitation List
HDD +5V@0.72A/ +12V@0.35A Max.
PCI slot expansion +5V@0.8A/+12@1.0A Max.
USB peripheral +5V@0.5A Max.
Processor Refer to Processor Limitation List
HDD +5V@0.72A/ +12V@0.35A Max.
PCI slot expansion +5V@0.8A/+12@1.0A Max.
USB peripheral +5V@0.5A Max.
Cash Drawer Device 24V@0.125A(+12V@0.25A) Max.
Parts Power Consumption limitation Remark
26 System Configuration Limitation Notice
Loading...