Acer P5290, P5281, P5271, P5390W, P5271I User Manual [pt]
INSTALLATION
INTERFACE CONNECTOR
Note: Connector interface is subject to model’s specifications
LAN
DC OUT
DVI
HDMI
VGA OUT
VGA IN 1
VGA IN 2
S-VIDEO VIDEO
AUDIO IN 1
AUDIO OUT
AUDIO IN 2
RS232
LAN
USB
WIRED REMOTE
1
USB
USB
4
DVI
DVI-D
DVI-D
8
D-Sub
D-Sub
DVD player
HDMI
HDMI
9
R B G
HDTV adapter
R B G
5
10
S-Video Output
Video Output
Y
Y
RS232
RS232
11
VGA
D-Sub
D-Sub
2
3
7
7
DVD player,
Set-top Box,
HDTV receiver
12
R
W
6
Internet
13
14
DVI
HDMI
VGA OUT
VGA IN 1
VGA IN 2
S-VIDEO VIDEO
AUDIO IN 1
AUDIO IN 2
RS232
USB
WIRED REMOTE
AUDIO OUT
LAN
DC OUT
mole x
E62405SP
R
English
简体中文
Quick Start
INSTALLATION
1. Power Cord
2. VGA Cable
3. Composite Video Cable
4. USB Cable
5. VGA to Component/HDTV Adapter
6. S-Video Cable
7. Audio Cable Jack/Jack
8. DVI Cable
9. HDMI Cable
10. 3 RCA Component Cable
11. RS232 Cable
12. Audio Cable Jack/RCA
13. LAN Cable
14. Audio Cable Jack for Wired Remote
Note: Connector interface is subject to model’s specifications
INTERFACE CONNECTOR
Connecting to a Computer
1. Ensure the projector and your
computer are turned off.
2. Connect one end of the VGA cable
to the “VGA IN” connector on the
projector; connect the other end to
the VGA connector on the computer
and tighten the screws.
3. Connect one end of the power cord
into the AC power socket on the
projector; connect the other end to an
electrical outlet.
Powering On the Projector
1. Remove the lens cap.
2. Turn on the projector first and then
the computer.
3. Adjust the position, focus and zoom.
4. Run you presentation.
Powering Off the Projector
1. Press the power button twice.
2. Do not remove AC power cord from
outlet until the projector fan shut
down.
快速启动卡
安装
1.
电源线
2. VGA
3.
4. USB
5. VGA
6. S-
7.
8. DVI
9. HDMI
10. 3 RCA
11. RS232
12.
13.
14.
注意: 连接接口视型号规格而定
1.
2. 将VGA
3.
1.
2.
3.
4.
1.
2.
线
复合视频线
线
转分量视频
视频线
Jack/Jack
音频线
线
线
分量视频线
线
Jack/RCA
音频线
网线
有线遥控器的音频线插孔
/HDTV
转接器
接口连接器
连接到电脑
请确认投影机和电脑已关闭。
连接的一端连接到投影机上标示
VGA IN
「
的
将电源线的一端连接到投影机上的
源插孔;另一端连接到插座。
移去镜头盖。
先打开投影机，然后打开电脑。
调整投影机的位置、焦距和缩放。
进行演示。
按两次电源按钮。
等到投影机风扇静止不动后，再拔下电
源线。
」连接器;将另一端连接到电脑
VGA
连接器并紧固螺丝。
打开投影机电源
关闭投影机电源
AC
电
Loading...