Page 1
Acer Projector
P1273/P1273n/P1276/P1373W/
P1273B/P1273i/P1373WB Series
User's Guide
Page 2
Copyright © 2013. Acer Incorporated.
All Rights Reserved.
Acer Projector P1273/P1273n/P1276/P1373W/P1273B/P1273i/P1373WB Series User's Guide
Original Issue: 03/2013
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer Projector P1273/P1273n/P1276/P1373W/P1273B/P1273i/P1373WB Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
Page 3
Information for your safety and comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
• Install the power supply unit before connecting the power cord to the AC
power outlet.
• Unplug the power cord before removing the power supply unit from the
projector.
• If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
iii
Warnings!
• Do not use this product near water.
• Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
• Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
• Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
Page 4
iv
• To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
• Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
• This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
• If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
• Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
• This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
• Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
Page 5
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
• the power cord or plug is damaged, cut or frayed
• liquid was spilled into the product
• the product was exposed to rain or water
• the product has been dropped or the case has been damaged
• the product exhibits a distinct change in performance, indicating a need
for service
• the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
v
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
• Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
• Turn on the projector first and then signal sources
• Do not place the product in following environments:
• Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
• Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
• Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
• Locations near fire alarms.
• Locations with an ambient temperature above 40 ºC/104 ºF.
• Locations where the altitudes are higher than 10000 feet.
• Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
Page 6
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
• Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
• Do not face the projector lens to the sun. It can lead to fire.
• When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
• Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
• Do not touch air outlet grille and bottom plate which becomes hot.
• Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
• Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
• Always open the lens shutter or remove the lens cap when the projector is
on.
• Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
• The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
• Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
• Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
• The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
• When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
• Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
• Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
• Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
• This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
Page 7
vii
“Lamp(s) contain Mercury,
Dispose Properly.”
Caution for Listening
To protect your hearing, follow these instructions.
• Increase the volume gradually until you can hear clearly and comfortably.
• Do not increase the volume level after your ears have adjusted.
• Do not listen to music at high volumes for extended periods.
• Do not increase the volume to block out noisy surroundings.
• Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
Page 8
viii
First things first
Usage Notes
Do:
• Turn off the product before cleaning.
• Use a soft cloth moistened with mild detergent to clean the display
housing.
• Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
• Block the slots and openings on the unit provided for ventilation.
• Use abrasive cleaners, waxes or solvents to clean the unit.
• Use under the following conditions:
• In extremely hot, cold or humid environments.
• In areas susceptible to excessive dust and dirt.
• Near any appliance that generates a strong magnetic field.
• Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
• Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
• To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
• Please do not open or disassemble the product as this may cause electric shock.
• When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
• This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
• Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
• When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
• Turn on the projector first and then the signal sources.
• Do not use lens cap when projector is in operation.
• When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Page 9
Information for your safety and comfort iii
First things first viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 2
Projector Overview 3
Projector Outlook 3
Control Panel 5
Remote Control Layout 6
Getting Started 8
Connecting the Projector 8
Turning the Projector On/Off 10
Turning on the Projector 10
Turning the projector off 11
Adjusting the Projected Image 12
Adjusting the Height of Projected Image 12
How to optimize image size and distance 13
How to get a preferred image size by adjusting
distance and zoom 17
Contents
User Controls 21
Installation menu 21
Acer Empowering Technology 22
Onscreen Display (OSD) Menus 23
Color 24
Image 26
Setting 28
Management 31
Audio 31
3D 32
Language 33
Acer LAN webpage management 34
Page 10
How to login in 34
Home 35
Control Panel 35
Network Setting 36
Alert Setting 36
Logout 37
Appendices 38
Troubleshooting 38
LED & Alarm Definition Listing 43
Cleaning and replacing the dust filters 44
Replacing the Lamp 45
Ceiling Mount Installation 47
Specifications 50
Compatibility modes 52
Regulations and safety notices 56
Page 11
English
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
1
• DLP
®
technology
• P1273/P1273n/P1276/P1273B/P1273i series : Native 1024 x 768 XGA
resolution
4:3 / 16:9 aspect ratio supported
• P1373W/P1373WB series : Native 1280 x 800 WXGA resolution
Full/4:3/16:9/L.Box aspect ratio supported
• Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
images
• High brightness and contrast ratio
• Versatile display modes (Bright, Presentation, Standard, Movie, Dark
Cinema, Game, Sports, User) enable optimum performance in any situation
• NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
• Top-loading lamp design allows easy lamp replacement
• Lower power consumption and economy (ECO) mode extends lamp life
• Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement
• Empowering Key reveals Acer Empowering Technology utilities (Acer
eView, eTimer, ePower, e3D Management) for easy adjustment of settings
• Equipped with HDMI™ connections supporting HDCP
• Advanced digital keystone correction optimizes presentations
• Smart detection delivers quick, intelligent source detection
• Multi-language onscreen display (OSD) menus
• Full-function remote control
• Manual focus projection lens zooms up to 1.1x
• 2x digital zoom and pan function
• Microsoft
Macintosh
®
Windows® 2000, XP, Vista®, Windows® 7, Windows® 8,
®
OS compliant
Page 12
2
English
M
ENU
POW
E
R
LA
M
PTEMP
S
E
Y
N
C
R
SOU
R
C
E
©
2
0
1
3
,
A
c
e
r
I
n
c
.
A
l
l
r
i
g
h
t
s
r
e
s
e
r
v
e
d
.
Acer Projector
P/N:MC.JG811.003
P1276/
P1273/n/B/i
P1373W/B/
Series
ZOOM
SOURCE
FREEZE
HIDE
MEDIA
SETUP
ZOOM
SOURCE
FREEZE
HIDE
MEDIA
SETUP
RATIO
©
2
0
1
3
,
A
c
e
r
I
n
c
.
A
l
l
r
i
g
h
t
s
r
e
s
e
r
v
e
d
.
Acer Projector
P/N:MC.JG811.003
P1276/
P1273/n/B/i
P1373W/B/
Series
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
Security card 2 x Batteries Carrying case
Quick Start Guide User's Guide (CD-ROM) Remote control
Dust Filters (Option) USB WiFi adapter
(Option)
User's Guide
(for multi-media and
wireless functions)
Quick Start Guide
(for multi-media and
wireless functions)
Remote control
(only for Japan area)
Page 13
English
Projector Overview
M
E
NU
PO
W
E
R
L
A
MP
TEMP
S
E
YNC
R
S
OU
R
C
E
5
3
2
1
4
7
6
8
P1273/P1276/P1373W
P1273n
P1373WB/P1273B/
P1273i
14
1513
12
16
11976542
16
10
83
1
Projector Outlook
Front / upper side
# Description # Description
1 Power button 5 Zoom lens
2 Control panel 6 Remote control receiver
3 Zoom lever 7 Tilt adjusting wheels
4 Focus ring 8 Security bar
Rear side
3
Note: Connector interface is subject to model's specifications.
Page 14
4
English
# Description # Description
1 LAN (RJ45 Port for 10/100M Ethernet)
(P1273n/P1373WB/P1273B/P1273i only)
2 1st USB connector (USB A1) 10 Audio input connector
3 2nd USB connector (USB A2) 11 RS232 connector
4 Mini USB connector (USB B) 12 Power socket
5 HDMI connector 13 PC analog signal/HDTV/component
6 Monitor loop-through output connector
(VGA-Out)
7 PC analog signal/HDTV/component video
input connector (VGA IN 1)
8 Composite video input connector 16 Dust filter inlets
9 S-Video input connector
video input connector (VGA IN 2)
14
Kensington
15 Audio output connector
TM
lock port
Page 15
English
Control Panel
5
32158
4
9
6 7
10
P1273B/P1373WB/P1273iP1273/P1276/P1273n/P1373W
1211
5
# Icon Function Description
1 POWER Power Indicator LED
2 LAMP Lamp Indicator LED
3 TEMP Temp Indicator LED
4 RESYNC Automatically synchronizes the projector
to the input source.
5 SOURCE Changes the active source.
6 POWER See the contents in "Turning the Projector
On/Off" section.
7 Empowering key
Unique Acer functions: e3D, eView, eTimer,
ePower Management.
8MENU
• Press "MENU" to launch the Onscreen
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
• Confirm your selection of items.
9 Four directional select
keys
10 Keystone Adjusts the image to compensate for
11 Back/Stop Press "Back/Stop" to stop playing media
12 Enter/Play/Pause Press "Enter/Play/Pause" to play/pause
Use to select items or make
adjustments to your selection.
distortion caused by tilting the projector (±
40 degrees).
file or go back to upper data folder.
media file.
Page 16
6
English
ZOOM
SOURCE
FREEZE
HIDE
MEDIA
SETUP
RATIO
3
6
8
10
12
16
14
20
22
24
4
1
5
7
9
11
13
15
19
17
21
23
2
18
ZOOM
SOURCE
FREEZE
HIDE
MEDIA
SETUP
26
25
E-26110
MC.JG811.001
BONTECH ELECTRONICS(K.S) CO ., LTD .
No. 2018, Zhonghuayuan west road,
Yushan town,Kunshan city, China
LASER MODULE : M-5.2-6.5x10-5.5x5.5
Model No:E-26141
MC.JG811.002
(only for Japan area)
Remote Control Layout
# Icon Function Description
1 Infrared
transmitter
2 POWER Refer to the "Turning the Projector On/Off" section.
3 3D Press "3D" to select 3D models.
4 SOURCE Changes the active source.
5 FREEZE To pause the screen image.
6 HIDE Momentarily turns off the video. Press "HIDE" to hide the
7 ZOOM Zooms the projector display in or out.
8 RATIO To choose the desired aspect ratio.
9 MEDIA_SETUP Press to enter media OSD setting.
10 Empowering
11 MENU
key
Sends signals to the projector.
image, press again to display the image.
(P1273/P1273n/P1276/P1273B/P1273i: 4:3 / 16:9
P1373W/P1373WB: Full/4:3/16:9/L.Box)
Unique Acer functions: e3D, eView, eTimer, ePower
Management.
• Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
• Confirm your selection of items.
Page 17
English
# Icon Function Description
12 KEYSTONE Adjusts the image to compensate for distortion caused by
13 Four
14 Pre./ Rewind Press "Pre./Rewind" to go to previous index or press
15 KeyPad 0~9 Press "0~9" to input a password in the "Security settings".
16 PgUp/PgDn For computer mode only. Use this button to select the next or
17 COMPONENT No function.
18 VIDEO To change source to COMPOSITE VIDEO.
19 VGA Press "VGA" to change source to the VGA connector. This
20 S-VIDEO To change source to S-Video.
21 SD/USB A Press "SD/USB A" to toggle between USB A1 and USB A2
22 USB B Press "USB B" to change source to mini USB (USB B).
23 HDMI/DVI To change source to HDMI™. (no DVI function)
24 LAN/WiFi Press “LAN/Wifi” as direct to network display.
(*)
25
(*)
26
directional
select keys
Enter/ Play/
Pause
Back/Stop Press "Back/Stop" to stop playing media file or go back to
Next/Fast
forward
Laser pointer Aim the remote at the viewing screen.
Laser button Aim the remote at the viewing screen, press and hold this
tilting the projector (± 40 degrees).
Use up, down, left, right buttons to select items or make
adjustments to your selection.
continuously to rewind the playing media file.
Press "Enter/Play/Pause" to play/pause media file.
upper data folder.
Press "Next/Fast-forward" once to go to next index or press
continuously to fast-forward the playing media file.
previous page. This function is only available when USB Ctrl
connector(USB type B) is connected to a computer via a USB
cable.
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
sources. (no SD function)
button to activate the laser pointer.
This function is not supported in Japanese market.
7
Note: "*" Japan area is not supported.
Page 18
8
English
HDTV adapter
9
10
RBG
RBG
D-Sub
D-Sub
5
D-Sub
D-Sub
5
R
W
7
6
R
W
7
Y
Y
11
2
1
HDMI
HDMI
4
USB
USB
3
RS232
RS232
8
USB
12
13
Video Output
S-Video Output
DVD player
DVD player,
Set-up Box,
HDTV receiver
DVD player,
Set-up Box,
HDTV receiver
Internet
Getting Started
Connecting the Projector
USB WiFi adapter
# Description # Description
1 Power cord 8 RS232 cable
2 LAN cable 9 VGA to component/HDTV adapter
3 USB cable 10 3 RCA component cable
4 HDMI cable 11 Composite video cable
5 VGA cable 12 Mouse
6 S-Video cable 13 USB disk/stick
7 Audio cable Jack/RCA
Page 19
English
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Connector interface is subject to model's specifications.
Note: USB cable needs powered extender if the length is over 5 m.
9
Page 20
10
English
M
E
NU
PO
W
E
R
L
AM
P
T
E
M
P
S
Y
NC
E
R
S
OUR
C
E
Power button
Turning the Projector On/Off
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2 Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
• If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
• If the screen displays "No Signal", please make sure the signal cables
are securely connected.
• If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
Page 21
11
English
Turning the projector off
1 To turn the projector off, press the power button. This message appears:
"Please press the power button again to complete the shutdown process."
Press the power button again.
2 The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3 As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2minute shutdown process. (only supported under "Instant Resume" mode)
4 Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
5 It is now safe to unplug the power cord.
Warning indicators:
• "Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
• "Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
Page 22
12
English
Tilt adjusting wheel
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with tilt adjusting wheels for adjusting the height of
image.
To raise/lower the image:
Use Tilt adjusting wheels to fine-tune the display angle.
Page 23
13
English
Height: 88 cm
from base to
top of image
Height:
80 cm
2.0 m
Desired Distance
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
How to optimize image size and distance
P1273/P1273n/P1273B/P1273i/P1276 series
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 2.0 m from the screen, good image quality is possible for image sizes
between 46" and 50".
Note: Remind as below figure, the space of 88 cm height is
required when located at 2.0 m distance.
Figure: Fixed distance with different zoom and screen size.
Page 24
14
English
P1273/P1273n/P1273B/P1273i/P1276 series
Diagonal
(inch)
<B>
Screen size
W (cm) x H (cm)
Screen size
Desired
Distance
(m)
Diagonal
<A>
Zoom Ratio: 1.1x
(inch)
<B>
1 23 47 x 35 40 25 51 x 38 44
2 46 93 x 70 80 50 103 x 77 88
2.5 57 116 x 87 100 63 128 x 96 111
3 69 140 x 105 120 76 154 x 115 133
3.5 80 163 x 122 140 88 179 x 135 155
4 92 186 x 140 160 101 205 x 154 177
4.5 103 209 x 157 181 114 231 x 173 199
5 114 233 x 174 201 126 256 x 192 221
6 137 279 x 209 241 151 308 x 231 265
7 160 326 x 244 281 177 359 x 269 310
8 183 372 x 279 321 202 410 x 308 354
9 206 419 x 314 361 227 462 x 346 398
10 229 465 x 349 401 252 513 x 385 442
(Min zoom) (Max zoom)
W (cm) x H (cm)
Top
From base
to top of
image (cm)
<C>
Top
From base to
top of image
(cm)
<C>
Page 25
English
P1373WB/P1373W series
Height: 90 cm
from base to
top of image
Height:
82 cm
2.0 m
Desired Distance
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
Example: If the projector is 2 m from the screen, good image quality is possible
for image sizes between 55" and 60".
Note: Remind as below figure, the space of 90 cm height is
required when located at 2 m distance.
15
Figure: Fixed distance with different zoom and screen size.
Page 26
16
English
P1373WB/P1373W series
Diagonal
(inch)
<B>
Screen size
W (cm) x H (cm)
Screen size
Desired
Distance
(m)
Diagonal
<A>
Zoom Ratio: 1.1x
(inch)
<B>
1.5 41 88 x 55 62 45 97 x 60 68
2 55 118 x 74 82 60 129 x 81 90
2.5 68 147 x 92 103 75 161 x 101 113
3 82 176 x 110 124 90 194 x 121 135
3.5 96 206 x 129 144 105 226 x 141 158
4 109 235 x 147 165 120 258 x 161 181
4.5 123 265 x 165 185 135 290 x 181 203
5 137 294 x 184 206 150 323 x 202 226
6 164 353 x 221 247 180 387 x 242 271
7 191 412 x 257 288 210 452 x 282 316
8 218 471 x 294 329 240 516 x 323 361
9 246 529 x 331 371 270 581 x 363 406
10 273 588 x 368 412 300 645 x 403 452
(Min zoom) (Max zoom)
W (cm) x H (cm)
Top
From base
to top of
image (cm)
<C>
Top
From base to
top of image
(cm)
<C>
Page 27
English
How to get a preferred image size by adjusting
A
C
D
B
Desired Distance
2.2 m
2.0 m
Height
from base to
top of image
50"
Desired
image size
distance and zoom
P1273/P1273n/P1273B/P1273i/P1276 series
17
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. For example: to obtain an image size of 50" set
the projector at a distance 2.0 m and 2.2 m from the screen and adjust the zoom
level accordingly.
Page 28
18
English
P1273/P1273n/P1273B/P1273i/P1276 series
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A>
30 61 x 46 1.2 1.3 53
40 81 x 61 1.6 1.7 70
50 102 x 76 2.0 2.2 88
60 122 x 91 2.4 2.6 105
70 142 x 107 2.8 3.1 123
80 163 x 122 3.2 3.5 140
90 183 x 137 3.6 3.9 158
100 203 x 152 4.0 4.4 175
120 244 x 183 4.8 5.2 210
150 305 x 229 5.9 6.6 263
180 366 x 274 7.1 7.9 315
200 406 x 305 7.9 8.7 351
250 508 x 381 9.9 10.9 438
300 610 x 457 11.9 526
Zoom Ratio: 1.1x
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
Page 29
19
English
A
C
D
B
Desired Distance
2.2 m
2.0 m
Height
from base to
top of image
60"
Desired
image size
P1373WB/P1373W series
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. For example: to obtain an image size of 60" set
the projector at a distance 2.0 m and 2.2 m from the screen and adjust the zoom
level accordingly.
Page 30
20
English
P1373WB/P1373W series
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A>
30 65 x 40 1.0 1.1 45
40 86 x 54 1.3 1.5 60
50 108 x 67 1.7 1.8 76
60 129 x 81 2.0 2.2 91
70 151 x 94 2.3 2.6 106
80 172 x 108 2.7 2.9 121
90 194 x 121 3.0 3.3 136
100 215 x 135 3.3 3.7 151
120 258 x 162 4.0 4.4 181
150 323 x 202 5.0 5.5 226
180 388 x 242 6.0 6.6 271
200 431 x 269 6.7 7.3 302
250 538 x 337 8.3 9.2 377
300 646 x 404 10.0 452
Zoom Ratio: 1.1x
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
Page 31
21
English
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the menu button on the control pad to launch the OSD for projector
installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
4 The Installation menu includes the following options:
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5 Push the menu button anytime to exit the menu and return to the Acer
welcome screen.
• Projection Mode
• Projection Location
• Auto Keystone settings
• Manual Keystone settings
• Language settings
• LAN/WiFi settings
• LAN IP / Mask settings
• Reset to factory default function
Page 32
22
English
Acer Empowering Technology
Acer Empowering Key provide four Acer unique functions, they are "Acer
eView Management", "Acer eTimer Management", "Acer ePower
Management" and "Acer e3D Management respectively.
Press " " key to launch the Onscreen display main menu to modify its
function.
When the Empowering Menu is displayed, use the " " key to select the main
menu.
Acer eView Management
Acer eTimer Management
Acer ePower Management
Acer e3D Management
"Acer eView Management" is for
display mode selection. Please refer to
Onscreen Display Menus section for
more detail.
"Acer eTimer Management" provides
the reminding function for
presentation time control. Please refer
to Onscreen Display Menus section for
more detail.
"Acer ePower Management" provides
user one shortcut to save the projector
life. Please refer to Onscreen Display
section for more detail.
"Acer e3D Management" provides the
3D functions. Please refer to Onscreen
Display Menus section for more detail.
Page 33
23
English
Main menu
Sub menu
Setting
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
• To open the OSD menu, press "MENU" on the remote control or control
panel.
• When the OSD is displayed, use the keys to select any item in the
main menu. After selecting the desired main menu item, press to enter
submenu for feature setting.
• Use the keys to select the desired item and adjust the settings by
using the keys.
• Select the next item to be adjusted in the submenu and adjust as described
above.
• Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
• To exit OSD, press "MENU" on the remote control or control panel again.
The OSD menu will close and the projector will automatically save the new
settings.
Page 34
24
English
Color
Display Mode
Wall color
Brightness
Contrast
Saturation
Tint
There are many factory presets optimized for various types of
images.
• Bright: For brightness optimization.
• Presentation: For meeting presentation.
• Standard: For common environment.
• Movie: For brighter and general movie/video/photo playing.
• Dark Cinema: For dark movie content.
• Game: For game content.
• Sports: For sport picture.
• User: Memorize user's settings.
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Adjust the brightness of the image.
• Press to darken image.
• Press to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
• Press to decrease the contrast.
• Press to increase the contrast.
Adjusts a video image from black and white to fully saturated
color.
• Press to decrease the amount of color in the image.
• Press to increase the amount of color in the image.
Adjusts the color balance of red and green.
• Press to increase the amount of green in the image.
• Press to increase the amount of red in the image.
Page 35
25
English
Color
Temperature
Dynamic Black
Gamma
Note: "Saturation" and "Tint" functions are not supported under computer
or HDMI mode.
Mode
Use this function to choose CT1 (5500K), CT2 (6500K, Native), CT3
(7500K), User mode.
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
Choose "On" to automatically optimize the display of dark movie
scenes enabling them to be shown in incredible detail.
<Note> "Dynamic Black" is only supported in P1276 series
Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.
Page 36
26
English
Image
Projection Mode
• Front: The factory default setting.
• Rear: Reverses the image so you can project from behind a
translucent screen.
Projection Location
• Auto: Automatically adjusts projection location of image.
• Desktop
• Ceiling: Turns the image upside down for ceiling-mounted
projection.
Aspect Ratio Use this function to choose your desired aspect ratio.
• Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
• Full: Resize image to fit full screen by width (1280 pixels) and
height (800 pixels).
• 4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
• 16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
• L.Box: Keep original signal aspect ratio and zoom in by 1.333
times.
<Note> "Full" and "L.Box" functions are only supported in P1373W,
P1373WB and P1273i series.
Auto Keystone Automatically adjusts vertical image.
Manual Keystone Adjust image distortion caused by tilting projection. (±40 degrees)
<Note> The Manual Keystone function is unavailable under Auto
Keystone setting to "On".
Sharpness Adjusts the sharpness of the image.
• Press to decrease the sharpness.
• Press to increase the sharpness.
Page 37
27
English
H. Position
(Horizontal
position)
V. Position
(Vertical position)
• Press to move the image left.
• Press to move the image right.
• Press to move the image down.
• Press to move the image up.
Frequency "Frequency" changes the projector's refresh rate to match the
Tracking Synchronizes the signal timing of the projector with the graphics card.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
If you experience an unstable or flickering image, use this function to
correct it.
error.
• Auto: Automatically adjust by information from player.
•
Limited Range: Prosess the input image as limited color range data.
• Full Range: Prosess the input image as full color range data.
HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen.
• Auto: Automatically adjust by information from player.
• Underscan: Always no overscan on HDMI image.
• Overscan: Always keep overscan on HDMI image.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI, DVI or Video mode.
Note: "Sharpness" functions is not supported under HDMI (RGB) or
Computer mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
Page 38
28
English
Setting
Startup Screen Use this function to select your desired startup screen. If you
Screen Capture Use this function to customize the startup screen. To capture the
Closed Caption
change the setting, the changes will take effect when you exit the
OSD menu.
• Acer: The default startup screen of your Acer projector.
• User: Use memorize picture from "Screen Capture" function.
image that you want to use as the startup screen, follow the
instructions below.
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set
to 4:3. For details, refer to the "Image" section.
• Change the "Startup Screen" from the default setting "Acer"
to "User".
• Press "Screen Capture" to customize the startup screen.
• A dialog box appears to confirm the action. Choose "Yes" to
use the current image as your customized startup screen. The
capture range is the red rectangular area. Choose "No" to
cancel the screen capture and exit the onscreen display (OSD).
• A message appears, stating that the screen capture is in
progress.
• When the screen capture is finished, the message disappears
and the original display is shown.
• The customized startup screen, as shown below, takes effect
when there is a new input signal or when you restart the
projector.
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
Page 39
29
English
Security Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
• Select "On" to enable the security function. The user has to
• If "Off" is selected, then the user can turn on the projector
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
• Press or to select the timeout interval.
• The range is from 10 minute to 990 minutes.
• When the time is up, the projector will prompt the user to
• The factory default setting of "Timeout(Min.)" is "Off".
• Once the security function is enabled, the projector will
User Password
• Press to setup or change the "User Password".
• Press number keys to set your password on the remote control
• Press to delete character.
• Enter the password when you see "Confirm Password"
• The password should be between 4 and 8 characters long.
• If you select "Request password only when plugging the
• If you select "Always request password while projector turns
enter a password to operate the projector. Please refer to the
"User Password" section for details.
without password.
enter the password again.
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
and press "MENU" to confirm.
displayed.
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
on.", the user has to enter the password every time when the
projector is turned on.
Note: This screen capture function is limited by 4:3 aspect ratio only.
Note: For XGA models, to get best quality for you desired image, suggest
end-user set PC resolution to 1024 x 768 before you use this function.
Note: For SVGA models, to get best quality for you desired image, suggest
end-user set PC resolution to 800 x 600 before you use this function.
Note: For WXGA models, to get best quality for you desired image,
suggest end-user set PC resolution to 1280 x 800 before you use this
function.
Page 40
30
English
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
• Press to change the "Administrator Password".
• The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
• An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
• If losing this security card and number, please contact with an
Acer service center.
Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen
is "On", users cannot change startup screen anymore and avoid
other users change that arbitrarily. Choose "Off" to unlock startup
screen.
VGA OUT (Standby) Default is "Off". Choose "On" to enable VGA OUT connection.
LAN
Reset
LAN/WiFi
Default is "Off". Choose "On" to enable LAN/WiFi connection. (for
P1273n/P1373W/P1373WB/P1273i series only)
LAN IP/Mask
Identify IP and Mask address. (for P1273n/P1373W/P1373WB/P1273i
series only)
LAN Reset
Reset LAN function. (for P1273n/P1373W/P1373WB/P1273i series
only)
• Press the button and choose "Yes" to return the
parameters on all menus to the factory default settings.
Page 41
English
Management
31
ECO Mode Choose "On" to dim the projector lamp which will lower power
High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at
Turn Off Mode
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
full speed continuously to allow for proper high altitude cooling of
the projector.
• Instant Off: Shuts down the projector without fan cooling.
• Instant Resume: Resumes the system when the Power button
is pressed again within 2 minutes.
Auto Shutdown The projector will automatically shutdown when there is no signal
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding Activate this function to display a reminder to change the lamp 30
Lamp Hour Reset
input after the allocated time. (default is 120 minutes)
hours before its expected end-of-life.
Press the button and choose "Yes" to turn the lamp hour
counter to 0 hours.
Audio
Volume
• Press to decrease the volume.
• Press to increase the volume.
Page 42
32
English
Mute
• Choose "On" to mute the volume.
• Choose "Off" to restore the volume.
Power On/Off Volume Select this function to adjust the notification volume when
Alarm Volume Select this function to adjust the volume of any warning
turning the projector on/off.
notifications.
3D
3D Choose "On" to enable DLP 3D function.
• On: Choose this item while using DLP 3D glasses, 120Hz 3D
capable graphics cards and HQFS format file or DVD with
corresponding SW player.
• Off: Turn off 3D mode.
3D Format Adjust the 3D format to display 3D content correctly.
3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D
3D Warning Message Choose "On" to display the 3D warning message.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).
Page 43
English
- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Language
33
Language
Choose the multilingual OSD menu. Use the or key to
select your preferred menu language.
• Press to confirm the selection.
Page 44
34
English
Acer LAN webpage management
How to login in
Open browser and enter the Server IP address by 192.168.100.10 to find below
homepage of acer LAN webpage management. A password is needed to login
in before using.
Select a user. Administrator is with high authority that can process more
operations such as network setting and alert setting. Default password of
administrator is "admin". And User is with normal authority with default
password by "user". Click Login button to enter into homepage with correct
password.
Note: LAN control function is supported in P1273n/P1373W/P1373WB/
P1273i series only.
Page 45
English
Home
Home page shows connection status and you can find three main functions
listed, Control Panel, Networking Setting and Alert Setting.
Note: Control Panel and Network Setting are only for Administrator
account.
Control Panel
35
Enduser can control and adjust projector setting value via this page.
Page 46
36
English
Network Setting
Enduser can set IP address, group name and password as wish. After change
network configurations or password, projector will reboot automatically after
press "Apply".
Note: Group Name and projector Name must be less then 32 characters.
Alert Setting
Enduser can send mail with error message right away if projector has problem.
Page 47
English
Logout
After tap Logout, you will return to login page within 5 seconds.
37
Page 48
38
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears
onscreen
2 Partial, scrolling
or incorrectly
displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))
• Connected as described in the "Getting Started"
section.
• Ensure none of the connector pins are bent or
broken.
• Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
• Make sure you have removed the lens cap and the
projector is switched on.
•
Press "RESYNC" on the remote control or control panel.
• For an incorrectly displayed image:
• Open "My Computer," open the "Control
Panel," and then double-click the "Display"
icon.
• Select the "Settings" tab.
• Verify that your display resolution setting is
lower than or equal to WUXGA-RB (1920 x
1200).
• Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
• Verify that the resolution setting is lower than
or equal to WUXGA-RB (1920 x 1200).
• Click the "Change" button under the
"Monitor" tab.
• Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
• Verify that the resolution setting of the
monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).
Page 49
39
English
3 Partial, scrolling
or incorrectly
displayed image
(For notebooks)
4 The screen of the
notebook
computer is not
displaying your
presentation
5 Image is unstable
or flickering
6 Image has vertical
flickering bar
• Press "RESYNC" on the remote control or control
panel.
• For an incorrectly displayed image:
• Follow the steps for item 2 (above) to adjust
the resolution of your computer.
• Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
• If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
• If you are using a Microsoft
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
• If you are using an Apple
notebook: In System Preferences, open Display and
select Video Mirroring "On".
®
Windows® based
®
Mac® OS based
• Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
• Change the display color depth settings on your
computer.
• Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
• Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7 Image is out of
focus
• Make sure the lens cap is removed.
• Adjusts the focus ring on the projector lens.
• Make sure the projection screen is within the
required distance of 3.9 to 39.4 feet (1.2 to 12.0
meters) (P1273/P1273n/P1273B/P1273i/P1276) from
the projector and 3.3 to 39.4 feet (1.0 to 10.0 meters)
(P1373WB/P1373W) from the projector. Refer to the
"How to Get a Preferred Image Size by Adjusting
Distance and Zoom" section for more information.
Page 50
40
English
8 Image is stretched
when displaying a
"widescreen"
DVD title
9 Image is too small
or too large
10 Image has slanted
sides
11 Image is reversed
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
• If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
• If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
• If you play an Letterbox(LBX) format DVD title,
please change the format to Letterbox(LBX) in the
projector OSD.
• Adjust the zoom lever on the top of the projector.
• Move the projector closer to or further from the
screen.
• Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.
• If possible, reposition the projector so that it is
centered on the screen.
• Press the "Keystone / " button on the remote
control until the sides are vertical.
• Press "MENU" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.
• Select "Image --> Projection Mode" on the OSD and
adjust the projection direction.
Page 51
English
OSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
41
Page 52
42
English
Problems with the Projector
# Condition Solution
1 The projector stops responding
to all controls
2 Lamp burns out or makes a
popping sound
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
Page 53
English
LED & Alarm Definition Listing
LED Messages
43
Message
Standby
(power cord plugged in)
Power button ON -- -- -- V
Lamp retry -- -- -- Quick
Turning off
(cooling state)
Turning off
(cooling completed)
Error (thermal failure) -- V -- V
Error (fan lock failure) -- Quick
Error (lamp breakdown) V -- -- V
Error (color Wheel fail) Quick
Lamp LED Temp LED Power LED
Red Red Red Blue
-- -- V --
-- -- Quick
-- -- V --
flashing
-- -- V
flashing
flashing
-- V
flashing
--
Page 54
44
English
R
E
S
Y
N
C
M
E
N
U
S
O
U
RC
E
P
O
W
E
R
LA
M
P
T
E
M
P
R
E
S
Y
N
C
M
E
N
U
S
O
U
R
C
E
P
O
W
E
R
LA
M
P
T
E
M
P
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
1
2
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then
unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1, 2)
4 To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipment.
5 If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
Page 55
45
English
6
7
5
4
RE
S
YNC
M
E
NU
SOUR
C
T
E
M
P
L
AMP
PO
WER
1
2
3
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
Page 56
46
English
To Change the Lamp
1 Turn off the projector by pressing the power button.
2 Allow the projector at least 30 mins to cool down.
3 Disconnect the power cord.
4 Open the screw cover on the right side of the projector. (Illustration #1)
5 Use a screwdriver to loosen the screw on the right side of the projector.
(Illustration #2)
6 Push and slide the top cover (Illustration #3) and then open the top cover.
(Illustration #4)
7 Loosen two screws on the lamp module (Illustration #5) and pull up the
lamp bar. (Illustration #6)
8 Pull out the lamp module by force. (Illustration #7)
To replace the lamp module, reverse the previous step.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
Page 57
English
Ceiling Mount Installation
20
mm
13
mm
8.4
mm
130 mm
49.9
mm
Short Rod
Ceiling Mount Base
- Attach to ceiling
Screw Type A
50 mm length / 8 mm diameter -
Long Rod
Extension Rod
Long Cylinder Cap
Tightening Screw
Medium Rod
Allen Key
- For tightening/loosening
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
47
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
Page 58
48
English
Smaller Washer
Projector Bracket
Large Washer
for adjustments
Screw Type B
Spacer
- For heat dissipation
-
Screw Type A
50 mm length/
8 mm diameter
Large cylinder cap
Allen Key
Tightening Screw
- For tightening/loosening
3 Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
-
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4 Attach the ceiling bracket to the ceiling rod.
Page 59
English
5 Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
Tightening Screw
Allen Key
55.00 mm 55.00 mm
82.30 mm75.28 mm
SCREW SPEC. M3 x 20 mm
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models Screw Type B Washer Type
P1273/P1273n/P1276/P1373W/
P1273B/P1273i/P1373WB
Diameter (mm) Length (mm) Large Small
320VV
49
Page 60
50
English
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
Projection system
Resolution P1373WB/P1373W: Native: WXGA (1280 x 800),
Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and
Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/K/
Aspect ratio 4:3 (native), 16:9
Displayable colors 1.07 Billion colors
Projection lens P1273/P1273n/P1273B/P1273i/P1276: F/2.41~2.55, f =
Projection screen size (diagonal) P1273/P1273n/P1273B/P1273i/P1276: 27.46" (0.70 m) -
Projection distance P1273/P1273n/P1273B/P1273i/P1276: 3.9' (1.2 m) - 39.4'
Throw ratio P1273/P1273n/P1273B/P1273i/P1276: 50"@2m (1.95 -
Horizontal scan rate 30k - 100 kHz
Vertical refresh scan rate 25-85 Hz, 120Hz (for 3D mode only)
Lamp type P1273/P1273n/P1273B/P1373WB/P1373W: 190 W user-
Keystone correction +/- 40 degrees
Audio Internal speaker with 2 W output
Weight 2.4 Kg (5.29 Ibs.)
Dimensions (L x W x H) 288 mm x 225 mm x 83.3 mm (11.3" x 8.9" x 3.3")
Remote control Full-function remote control
Digital Zoom 2X
Power supply AC input 100 - 240 V, 50 - 60 Hz
®
DLP
Maximum: UXGA (1600 x 1200),
1080p(1920x1080)
P1273/P1273n/P1273B/P1273i/P1276: Native: XGA (1024
x 768), Maximum: UXGA (1600 x 1200),
1080p(1920x1080)
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA+
K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p, 576p),
SDTV (480i, 576i)
21.79~23.99 mm, 1.1X manual zoom lens
P1373WB/P1373W: F/2.5 ~2.6, f = 21.86~24.00 mm, 1.1X
manual zoom lens
302.8" (7.69 m)
P1373WB/P1373W: 27.3" (0.69 m) - 300" (7.62 m)
(12.0 m)
P1373WB/P1373W: 3.3' (1.0 m) - 32.8' (10.0 m)
2.15:1)
P1373WB/P1373W: 60"@2m (1.55 ~ 1.70:1)
replaceable lamp
P1276: 240 W user-replaceable lamp
Page 61
51
English
Power consumption P1273/P1273n/P1273B/P1273i/P1373WB/P1373W:
Operating temperature 5°C to 40°C / 41°F to 104°F
Standard package contents
Normal mode: 235W ± 10% @ 110VAC
ECO mode: 197W ± 10% @ 110VAC
Standby mode < 0.5W
P1276:
Normal mode: 305W ± 10% @ 110VAC
ECO mode: 240W ± 10% @ 110VAC
Standby mode < 0.5W
• AC power cord x1
• VGA cable x1
• Remote control x1
• Batteries x 2 (for remote control)
• User's Guide (CD-ROM) x1
• Quick start guide x1
• Security card x 1
I/O connectors
Power socket V V V
RJ45 LAN input X V V
Mini USB V V V
HDMI V V V
VGA output V V V
VGA IN 1 V V V
P1273/P1276/
P1373W
P1273n
P1373WB/
P1273B/
P1273i
VGA IN 2 V V V
Composite video V V V
S-Video V V V
3.5 mm audio jack input V V V
3.5 mm audio jack output V V V
RS232 V V V
USB A1 X X V
USB A2 X X V
* Design and specifications are subject to change without notice.
Page 62
52
English
Compatibility modes
A. VGA Analog
1 VGA Analog - PC Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
VGA 640x480 60 31.47
640x480 72 37.86
640x480 75 37.50
640x480 85 43.27
640x480 119.51 61.60
SVGA 800x600 56 35.20
800x600 60 37.88
800x600 72 48.08
800x600 75 46.88
800x600 85 53.67
800x600 119.85 77.20
XGA 1024x768 60 48.36
1024x768 70 56.48
1024x768 75 60.02
1024x768 85 68.67
1024x768 119.804 98.80
SXGA 1152x864 70 63.80
1152x864 75 67.50
1152x864 85 77.10
1280x1024 60 63.98
1280x1024 72 77.90
1280x1024 75 79.98
1280x1024 85 91.15
QuadVGA 1280x960 60 60.00
1280x960 75 75.00
SXGA+ 1400x1050 60 65.32
UXGA 1600x1200 60 75.00
PowerBook G4 640x480 60 31.50
640x480 66.6(67) 35.00
800x600 60 37.88
1024x768 60 48.36
1152x870 75 68.68
1280x960 75 75.20
i Mac DV (G3) 1024x768 75 60.30
Page 63
English
2 VGA Analog - Extended Wide timing
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.78
1280x768 75 60.29
1280x768 85 68.63
1280x720 60 44.80
1280x800 60 49.60
1440x900 60 55.90
1680x1050 60 65.30
1366x768 60 47.71
1920x1080-RB 60 66.60
UWXGA 1920x1200-RB 60 (59.95) 74.04
3 VGA Analog -Component Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
480i 720x480 59.94 (29.97) 15.70
480p 720x480 59.94 31.47
576i 720x576 50(25) 15.60
576p 720x576 50 31.25
720p 1280x720 60 45.00
720p 1280x720 50 37.50
1080i 1920x1080 60(30) 33.75
1080i 1920x1080 50(25) 28.10
1080p 1920x1080 60 67.50
1080p 1920x1080 50 56.25
1080p 1920x1080 24 27.00
1080p 1920x1080 23.97 26.97
Graphic source
monitor range
limits
Horizontal scan rate: 30-100 kHz
Vertical scan rate: 50-120 Hz
Max. pixel rate: 165 MHz
53
B. HDMI Digital
1 HDMI - PC Signal (same as DVI)
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
VGA 640x480 60 31.47
640x480 72 37.86
640x480 75 37.50
640x480 85 43.27
Page 64
54
English
640x480 119.51 61.61
SVGA 800x600 56 35.20
800x600 60 37.88
800x600 72 48.08
800x600 75 46.88
800x600 85 53.67
800x600 119.85 77.20
XGA 1024x768 60 48.36
1024x768 70 56.48
1024x768 75 60.02
1024x768 119.804 98.80
1152x864 75 67.50
1152x864 85 77.10
1280x1024 60 64.00
1280x1024 72 77.90
1280x1024 75 79.98
1280x1024 85 91.15
1280x960 75 75.00
PowerBook G4 640x480 60 31.50
640x480 66.6(67) 35.00
800x600 60 37.88
1024x768 60 48.36
1152x870 75 68.68
1280x960 75 75.20
i Mac DV (G3) 1024x768 75 60.30
2 HDMI - Extended Wide timing (same as DVI)
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.78
1280x768 75 60.29
1280x768 85 68.63
1280x720 60 44.80
1280x800 60 49.60
1440x900 60 55.90
1680x1050 60 65.30
1366x768 60 47.71
1920x1080-RB 60 66.60
UWXGA 1920x1200-RB 60 (59.95) 74.04
Page 65
English
3 HDMI - Video Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
480i 720x480 59.94 (29.97) 15.70
480p 720x480 59.94 31.47
576i 720x576 50(25) 15.60
576p 720x576 50 31.25
720p 1280x720 60 45.00
720p 1280x720 50 37.50
1080i 1920x1080 60(30) 33.75
1080i 1920x1080 50(25) 28.10
1080p 1920x1080 60 67.50
1080p 1920x1080 50 56.25
1080p 1920x1080 24 27.00
1080p 1920x1080 23.97 26.97
1080p 1920x1200-RB 60(59.95) 74.04
Graphic source
monitor range
limits
Horizontal scan rate: 30-100 kHz
Vertical scan rate: 50-120 Hz
Max. pixel rate: 170 MHz
55
Page 66
56
English
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Page 67
57
English
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
English
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm
for the latest country list.
Page 68
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Declare under our own responsibility that the product:
Product: Projector
Trade Name: Acer
Model Number: DNX1123/DWX1125/DWX1129/DNX1130/DNX1131/DNX1146
P1273/P1273n/P1276/P1373W/P1273B/P1273i/P1373WB
To which this declaration refers conforms to the relevant standard or other standardizing documents:
• EN 55022:2006/A1:2007 Class B; EN 55024:2010
• EN 61000-3-2:2006+A1:2009+A2:2009 Class A; EN61000-3-3:2008
• EN 60950-1:2006+A11:2009+A1:2010+A12:2011
• EN 50581:2012
• Regulation (EC) No. 1275/2008; EN 62301:2005
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2013.
_______________________________
RU Jan / Sr. Manager Date
Regulation, Acer Inc.
Mar. 20, 2013
Page 69
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product: DLP Projector
Model Number: DNX1123/DWX1125/DWX1129/DNX1130/DN
X1131/DNX1146
Machine Type: P1273/P1273n/P1276/P1373W/P1273B/P1273i/
P1373WB
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147
Loading...