Acer Projector User's Guide
Original Issue: 05/2015
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Model number: _________________________________
Serial number: __________________________________
Date of purchase: _______________________________
Place of purchase: ______________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
Page 3
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•Install the power supply unit before connecting the power cord to the AC
power outlet.
•Unplug the power cord before removing the power supply unit from the
projector.
•If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
iii
Warnings!
•Do not use this product near water.
•Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
•To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Page 4
iv
•Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
•If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
•This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•the power cord or plug is damaged, cut or frayed
Page 5
•liquid was spilled into the product
•the product was exposed to rain or water
•the product has been dropped or the case has been damaged
•the product exhibits a distinct change in performance, indicating a need
for service
•the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
•Turn on the projector first and then signal sources
•Do not place the product in following environments:
•Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
•Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
•Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
•Locations near fire alarms.
•Locations with an ambient temperature above 40 ºC/104 ºF.
•Locations where the altitudes are higher than 10000 feet.
•Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
•Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
•Do not face the projector lens to the sun. It can lead to fire.
•When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
•Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
v
Page 6
vi
6°
6°
•Do not touch air outlet grille and bottom plate which becomes hot.
•Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
•Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
•Always open the lens shutter or remove the lens cap when the projector is
on.
•Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
•The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
•Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
•Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
•The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
•When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
•Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
•Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
•Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
•This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
•The projector should be placed in a horizontal way by means of desktop or
ceiling mount mode only, and its tilt angles should not exceed 6 degrees,
otherwise it would cause dramatical decrease of lamp life or severe safety
concern of system malfunction.
Page 7
vii
“Lamp(s) contain Mercury,
Dispose Properly.”
RG2
Caution for Listening
To protect your hearing, follow these instructions.
•Increase the volume gradually until you can hear clearly and comfortably.
•Do not increase the volume level after your ears have adjusted.
•Do not listen to music at high volumes for extended periods.
•Do not increase the volume to block out noisy surroundings.
•Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
Do not stare into the beam, RG2
"As with any bright source, do not stare into the direct beam, RG2 IEC 624715:2015"
Page 8
viii
First things first
Usage Notes
Do:
•Turn off the product before cleaning.
•Use a soft cloth moistened with mild detergent to clean the display
housing.
•Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•Block the slots and openings on the unit provided for ventilation.
•Use abrasive cleaners, waxes or solvents to clean the unit.
•Use under the following conditions:
•In extremely hot, cold or humid environments.
•In areas susceptible to excessive dust and dirt.
•Near any appliance that generates a strong magnetic field.
•Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
•To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•Please do not open or disassemble the product as this may cause electric shock.
•When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
•This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
•When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•Turn on the projector first and then the signal sources.
•Do not use lens cap when projector is in operation.
•When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Page 9
Information for your safety and comfortiii
First things firstviii
Usage Notesviii
Precautionsviii
Introduction1
Product Features1
Package Overview2
Projector Overview3
Projector Outlook3
Control Panel5
Remote Control Layout6
MHL (Mobile High-Definition Link) Control8
Getting Started9
Connecting the Projector9
Turning the Projector On/Off11
Turning on the Projector11
Turning the projector off12
Adjusting the Projected Image13
Adjusting the Height of Projected Image13
How to optimize image size and distance14
How to get a preferred image size by
adjusting distance and zoom15
How to get a preferred image position by
adjusting lens shift16
User Controls18
Installation menu18
Onscreen Display (OSD) Menus20
Color21
Image23
Setting25
Management27
Audio28
3D29
Language29
Contents
Page 10
Appendices30
Troubleshooting30
LED & Alarm Definition Listing34
How to install cable management35
Cleaning and replacing the dust filters37
Replacing the Lamp38
Ceiling Mount Installation39
Specifications42
Compatibility modes44
Regulations and safety notices49
Page 11
English
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
®
•DLP
•1920x1080 1080p resolution
•Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D
•Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
•High brightness and contrast ratio
•Acer LumiSense+ technology can intelligently optimizes the brightness and
•Versatile display modes (Bright, Standard, sRGB, Rec. 709, Movie, Dark
•NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
•Lower power consumption and economy (ECO) mode extend lamp life
•Acer EcoProjeciton Technology delivers Intelligent power management
•Equipped with HDMI
•Support HDMI CEC function
•Advanced digital keystone and 4-corner correction optimizes presentations
color saturation of projected image based on actual ambient light.
Cinema, Game, Sport, ISF Night, ISF Day, User) enable optimum
performance in any situation
approach and physical efficiency improvement
™ & MHL connection supporting HDCP
®
Windows® 2000, XP, Vista®, Windows 7, Windows 8,
®
Macintosh
OS compliant
1
Note: Functions vary depending on model definition.
Page 12
2
English
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
ProjectorPower cordVGA cable
HDMI extension cableSecurity cardUser’s guide
Quick start guideCarrying case
Remote control2 x Batteries
Dongle rubberWirelessHD-Kit
(option)
(option)
(option)
Dust filters
(option)
Cable management cover
MHL HDMI
DC 5V IN
WirelessCAST
(option)
Page 13
English
Projector Overview
5
6948
7
11
10
2
1
3
Projector Outlook
Front / upper side
#Description#Description
1Ambient light sensor7Power button
2Remote control receiver8Control panel
3Lens Cap9Lamp cover
4Focus ring10 Tilt adjusting wheels
5Lens shift control ring11 Projection lens
6Zoom lever
3
Page 14
4
English
1/MHL
2
DC 5V OUT
AUDIO IN Pb/Cb
AUDIO OUT YRS232
VGA IN
DC 12V OUT
USB CTRL
VIDEOPr/Cr
21335
11
12
4
1098
6147
1
Right / Rear side
#Description#Description
1Composite video input connector8Audio out connector
25V DC output connector9YPbPr/YCbCr input connector
312V DC output connector10 RS232 connector
4PC analog signal/HDTV/component
video input connector (VGA, VGA IN,
VGA IN 1, VGA IN 2)
5HDMI/MHL connector (HDMI/MHL,
HDMI 1/MHL)
6Security bar13 Power socket
7Audio in connector14 Kensington™ lock port
11
Mini USB Ctrl connector (for firmware
upgrade)
12
HDMI 2 connector
Note: Functions vary depending on model definition.
Page 15
English
Control Panel
123
5
8
4
67
10
9
#IconFunctionDescription
1POWERPower Indicator LED
2LAMPLamp Indicator LED
3TEMPTemp Indicator LED
4RESYNCAutomatically synchronizes the projector
5SOURCE Changes the active source.
6POWERSee the contents in "Turning the Projector
7MODE
8MENU•Press "MENU" to launch the Onscreen
9Four directional select
10KeystoneAdjusts the image to compensate for
keys
5
to the input source.
On/Off" section.
Press "MODE" to select the display mode
from Bright, Standard, Movie, Dark
Cinema, Game, Sport and User.
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
•Confirm your selection of items.
Use to select items or make
adjustments to your selection.
distortion caused by tilting the projector.
Note: Functions vary depending on model definition.
Page 16
6
English
HIDE
RATIO
SOURCE
MODE
MEDIA
SETUP
ZOOM
FREEZE
3
6
8
10
12
16
14
20
22
24
4
1
5
7
9
11
13
15
19
17
21
23
2
18
HIDE
MEDIA
SETUP
MODE
SOURCE
ZOOM
FREEZE
26
25
Model No:E-26171
MC.JG811.009
E-26110
BONTECH ELECTRONICS(K.S) CO ., LTD .
No. 2018, Zhonghuayuan west road,
Yushan town,Kunshan city, China
LASER MODULE : M-5.2-6.5x10-5.5x5.5
MC.JK211.004
Model No:E-26281
Remote Control Layout
# IconFunctionDescription
1Infrared
transmitter
2POWERRefer to the "Turning the Projector On/Off" section.
Sends signals to the projector.
33DPress "3D" to select 3D models.
4SOURCEChanges the active source.
5MODEPress "MODE" to select the display mode from Bright,
Standard, Movie, Dark Cinema, Game, Sport and User.
6HIDEMomentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
7MEDIA_SETUP No function.
8RATIOTo choose the desired aspect ratio.
FREEZE
directional
select keys
To pause the screen image.
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
•Confirm your selection of items.
tilting the projector.
Use up, down, left, right buttons to select items or make
adjustments to your selection.
9ZOOMZooms the projector display in or out.
10
11MENU•Press "MENU" to launch the Onscreen display (OSD)
12KEYSTONEAdjusts the image to compensate for distortion caused by
13Four
Page 17
English
# IconFunctionDescription
14Pre./RewindNo function.
Enter/ Play/
Pause
Back/StopNo function.
Next/Fast
forward
15KeyPad 0~9Press "0~9" to input a password in the "Security" OSD.
16PgUp/PgDnFor computer mode only. Use this button to select the next or
17COMPONENT Press "COMPONENT" to change source to Component video.
18VIDEOTo change source to COMPOSITE VIDEO.
19VGAPress "VGA" to change source to the VGA connector. This
20S-VIDEONo function.
21SD/USB ANo function.
22USB BFor USB control and firmware upgrade.
23HDMI/DVITo change source to HDMI/MHL. (no DVI function)
24LAN/WiFiNo function.
25
26
Laser pointer Aim the remote at the viewing screen.
Laser buttonAim the remote at the viewing screen, press and hold this
No function.
No function.
previous page. This function is only available when USB Ctrl
connector (mini type B) is connected to a computer via a USB
cable.
This connection supports YPbPr (480p/576p/720p/1080i) and
YCbCr (480i/576i).
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
button to activate the laser pointer.
This function is not supported in Japanese market.
7
Note: Functions vary depending on model definition.
Page 18
8
English
HIDE
MEDIA
SETUP
MODE
SOURCE
ZOOM
FREEZE
7
8
56
4
3
2
1
MHL (Mobile High-Definition Link) Control
#IconComponentDescription
1MODE•Press "MODE" button for one second to activate the
2SOURCEPress the "SOURCE" button to toggle between Navigation
3MENUPress to launch the root memu.
4Direction Keys Use up, down, left, right buttons to select items or make
5SelectTo select the file. (only for Navigation mode)
6ExitTo exit the file. (only for Navigation mode)
7PgUp/PgDnUse the button to select the next or previous
8KeyPad 0~9Number buttons. (only for Numeric mode)
MHL Control Mode.
•To exit, press the "MODE" button again.
or Numeric mode.
(only for Navigation mode)
adjustments to your selection.
(only for Navigation mode)
page. (only for Navigation mode)
Note: Functions vary depending on model definition.
Page 19
English
Getting Started
1/MHL
2
DC 5V OUT
AUDIO IN Pb/Cb
AUDIO OUTYRS232
VGA IN
DC 12V OUT
USB CTRL
VIDEOPr/Cr
1
RS232
RS232
12
RS232
HDTV adapter
3
4
RBG
RBG
D-Sub
D-Sub
2
HDMI
HDMI
5
HDMI
HDMI
5
USB
USB
13
HDMI
7
USB
MHL
Y
Y
10
R
W
11
R
W
11
R
W
11
HDMI
HDMI
6
9
9
8
R
G
B
4
RG
B
Video output
DVD player,
Set-top Box,
HDTV receiever
DVD player
Power Bank
DVD player
DVD player,
Set-top Box,
HDTV receiever
Acer Dongle
Smart Phone
Connecting the Projector
9
Page 20
10
English
#Description#Description
1Power cord812V DC cable
2VGA cable9USB cable for charging device
3VGA to component/HDTV adapter10 Composite video cable
43 RCA component cable11 Audio cable Jack/RCA
5HDMI cable12 RS232 cable
6HDMI extension cable (for wireless
dongle)
7MHL cable (MicroUSB to HDMI)
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.
Note: Some smartphones require a converter (supplied by
smartphone maker) to enable the MHL function.
Note: Before connecting the projector, remove the cable
management, refer to "Removing the cable management"
section.
Note: DC 12V out connector support 12V/100mA power for screen
control only.
Note: USB DC 5V out connector support 5V/1.5A power output for
power bank charging only when MHL source is not detected.
13 USB cable
Page 21
English
Turning the Projector On/Off
Power button
Turning on the Projector
1Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2Turn on the projector by pressing "Power" button on the control panel or
remote control, and the Power indicator LED will turn blue.
3Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
•If the screen displays "No Signal", please make sure the signal cables
are securely connected.
•If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
11
Page 22
12
English
Turning the projector off
1To turn the projector off, press and hold the power button. This message
appears: "Please press the power button again to complete the shutdown
process." Press the power button again.
2The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2minute shutdown process. (only supported under "Instant Resume" mode)
4Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
5It is now safe to unplug the power cord.
Warning indicators:
•"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
•"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
Note: Functions vary depending on model definition.
Page 23
English
Adjusting the Projected Image
Tilt adjusting wheel
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
Use Tilt adjusting wheel to fine-tune the display angle.
13
Page 24
14
English
127"
93"
93"
A
C
B
Height: 183 cm
from base to top
of image
Height:
135 cm
3 m
Desired Distance
M
a
x
s
c
r
e
e
n
s
i
z
e
M
i
n
s
c
r
e
e
n
s
i
z
e
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
•1080p series
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 93" and 127".
Note: Remind as below figure, the space of 183 cm height is
required when located at 3 m distance.
Desired
Distance
(m)
<A>
13169 x 39454294 x 5361
1.34090 x 505855122 x 6870
1.547103 x 586763140 x 7992
262138 x 789085187 x 105122
2.578172 x 97112106234 x 132153
393207 x 116135127281 x 158183
3.5109241 x 136157148328 x 184214
4125276 x 155180169375 x 211244
4.5140310 x 174202190421 x 237275
5156345 x 194225211468 x 263305
5.5171379 x 213247233515 x 290336
6187414 x 233270254562 x 316367
6.5202448 x 252292275609 x 342397
7.1221489 x 275319300665 x 374434
Zoom Ratio: 1.36x
Screen size
Diagonal
(inch)
<B>
(Min zoom)(Max zoom)
W (cm) x H
(cm)
From base to
top of image
Top
(cm)
<C>
Screen size
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to top
of image (cm)
Top
<C>
Page 25
English
How to get a preferred image size by adjusting
Desired Distance
1.9 m
1.4 m
Height: 87 cm
from base to top of
image
60"
Desired
image size
distance and zoom
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
•1080p series
To obtain an image size of 60" set the projector at a distance 1.4 m and 1.9 m
from the screen.
A
D
15
B
C
Desired Image SizeDistance (m)Top (cm)
Diagonal (inch)
<A>
3169 x 391.045
4089 x 500.91.358
50111 x 621.21.672
60133 x 751.41.987
70155 x 871.72.2101
80177 x 1001.92.6116
90199 x 1122.12.9130
100221 x 1252.43.2144
120266 x 1492.83.9173
150332 x 1873.54.8217
180398 x 2244.35.8260
200443 x 2494.76.4289
250553 x 3115.98.0361
300664 x 3747.1433
Zoom Ratio: 1.36x
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
Page 26
16
English
Vertical Lens
Shift ring
How to get a preferred image position by adjusting
lens shift
The projector is equipped with lens shift for adjusting the position of projected
image up and down without requiring you to physically move the projector.
Note: The figures shown in this section are for reference only not
approximate value. The figures between units can be different
due to assembly tolerance.
Page 27
English
The vertical image height can be adjusted between -6% and 21% of the image
H
V
V
Offset max=V x 21%
Offset min=V x -6%
height. (The minimum vertical image offset is fixed at 5% of the image height
above the centre of the projector lens.)
17
Page 28
18
English
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the "MENU" button on the remote control to launch the OSD for
projector installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
4 The Installation menu includes the following options:
•Projection method
•Projection Mode
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•H. Keystone
•V. Keystone
•LAN/WiFi
•LAN
•LAN IP/Mask
•Wireless HD dongle settings
•Language settings
•DC 5V Out (Standby)
Page 29
English
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5 Push the MENU button anytime to exit the menu and return to the Acer
welcome screen.
Note: Functions vary depending on model definition.
19
Page 30
20
English
Main menu
Sub menu
Setting
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•To open the OSD menu, press "MENU" on the remote control or control
panel.
•When the OSD is displayed, use the keys to select any item in the
main menu. After selecting the desired main menu item, press to enter
submenu for feature setting.
•Use the keys to select the desired item and adjust the settings by
using the keys.
•Select the next item to be adjusted in the submenu and adjust as described
above.
•Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
•To exit OSD, press "MENU" on the remote control or control panel. The
OSD menu will close and the projector will automatically save the new
settings.
Note: Some of the following OSD settings may not be available. Please refer
to the actual OSD of your projector.
Note: Functions vary depending on model definition.
Page 31
English
Color
21
LumiSense
+
Display Mode
Wall color
Brightness
Contrast
Saturation
The light sensor of LumiSense+ technology can intelligently
optimize the brightness and color saturation of projected image
based on actual ambient light. The feature greatly enhances dark
detail visibility and color saturation.
•Off: For normal mode. (ambient light sensor is off)
•Auto Bright: Light sensor is on to automatically detect
ambient light and optimize the brightness and color
saturation of projected image.
•Dynamic Black:automatically optimize the display of dark
movie scenes enabling them to be shown in incredible detail.
There are many factory presets optimized for various types of
images.
•Bright: For brightness optimization.
•Standard: For common environment.
•sRGB: standard RGB color space.
•Game: For game content.
•Movie: For brighter and general movie/video/photo playing.
•Dark Cinema: For dark movie content.
•Sport: For sport picture.
•Rec. 709: standard Rec. 709 color space.
•ISF Day: Calibrate and optimize the projection image based
on bright environment by an ISF Certified technician.
•ISF Night: Calibrate and optimize the projection image based
on dark environment by an ISF Certified technician.
•User: Memorize user's settings.
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Adjust the brightness of the image.
•Press to darken the image.
•Press to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
•Press to decrease the contrast.
•Press to increase the contrast.
Adjusts a video image from black and white to fully saturated
color.
•Press to decrease the amount of color in the image.
•Press to increase the amount of color in the image.
Page 32
22
English
Tint
Color
Temperature
Gamma
Advanced
Adjusts the color balance of red and green.
•Press to increase the amount of green in the image.
•Press to increase the amount of red in the image.
Mode
Use this function to choose CT1, CT2 (Native), CT3, User mode.
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
R Bias
Adjusts the red bias for color temperature optimization.
G Bias
Adjusts the green bias for color temperature optimization.
B Bias
Adjusts the blue bias for color temperature optimization.
Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.
Ind. Color Management
Adjusts the red, green, blue, cyan, yellow and magenta colors.
Ind. Hue
Adjusts the color balance of red and green.
Ind. Saturation
Adjusts the selected color to be less or more saturated color.
Ind. Gain
Adjusts the selected color's contrast.
Brilliant Color
Produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images.
White Peaking
Increases the brightness of whites that are near 100%. (video
sources only)
Film Mode
Sets the image optimized to 24-frame True Film mode.
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Black Extension
This ensures optimum black level for each analog source.
ISF
1. The certified ISF technician will calibrate and optimize the
projection image according to your actual environment. The ISF
input password will be kept by technician only.
2. “ISF Day” and “ISF Night” will not be shown in display mode if
projector equipped with ISF function has not been calibrated by
an ISF certified technician. For more information, please go to
ISF official website: https://www.imagingscience.com and
contact the dealer located in your country.
3. The ISF calibration will be charged and guaranteed by ISF
certified calibrator, and thereby Acer is not responsible for the
calibration service.
Page 33
English
Note: "Saturation" and "Tint" functions are not supported under computer
or HDMI mode.
Note: Functions vary depending on model definition.
Image
Projection Mode
• Front: The factory default setting.
• Rear: Reverses the image so you can project from behind a
translucent screen.
Projection Location
• Auto: Automatically adjusts projection location of image.
• Desktop
• Ceiling: Turns the image upside down for ceiling-mounted
projection.
Aspect RatioUse this function to choose your desired aspect ratio.
H./V. KeystoneAuto V. Keystone
4 Corner
Correction
•Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
•Full: Resize image to fit full screen by width (1280 pixels) and
height (800 pixels).
•4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
•16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
•L.Box: Keep original signal aspect ratio and zoom in by 1.333
times.
Automatically adjusts vertical image.
H. Keystone
Press the or button to adjust image distortion horizontally
and makes a squarer image.
V. Keystone
Press the or button to adjust image distortion vertically and
makes a squarer image.
Manually adjusts the shape and size of an image that is unevenly
rectangular on all sides. Press "MODE" repeatedly to select the corner
that you wish to adjust. Press four directional selection keys to adjust
the image shape.
23
<Note> The function is unavailable when H./ V. Keystone is adjusted.
Page 34
24
English
SharpnessAdjusts the sharpness of the image.
•Press to decrease the sharpness.
•Press to increase the sharpness.
H. Position
(Horizontal
position)
V. Position
(Vertical position)
Frequency"Frequency" changes the projector's refresh rate to match the
TrackingSynchronizes the signal timing of the projector with the graphics card.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display
HDMI Scan InfoAdjust the overscan ratio of the HDMI image on screen.
•Press to move the image left.
•Press to move the image right.
•Press to move the image down.
•Press to move the image up.
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
If you experience an unstable or flickering image, use this function to
correct it.
error.
•Auto: Automatically adjust by information from player.
•Limited Range: Prosess the input image as limited color range data.
•Full Range: Prosess the input image as full color range data.
•Auto: Automatically adjust by information from player.
•Underscan: Always no overscan on HDMI image.
•Overscan: Always keep overscan on HDMI image.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI or Video mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
Note: Functions vary depending on model definition.
Page 35
English
Setting
25
Startup ScreenUse this function to select your desired startup screen. If you change
Screen Capture
Source LockWhen Source Lock is turned "Off", the projector will search for
Closed Caption
Auto ScreenDefault is "On", the down/up move of electronic screen will be
DC 5V Out (Standby) Default is "Off". Choose "On" to enable DV 5V OUT connection
HDMI CECDefault is "Off". Select “On” to enable HDMI CEC function.
Reset
the setting, the changes will take effect when you exit the OSD
menu.
•Acer: The default startup screen of your Acer projector.
•User: Use memorize picture from "Screen Capture" function.
Use this function to customize the startup screen. To capture the
image that you want to use as the startup screen, follow the
instructions below.
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set to
4:3. For details, refer to the "Image" section.
•Change the "Startup Screen" from the default setting "Acer"
to "User".
•Press "Screen Capture" to customize the startup screen.
•A dialog box appears to confirm the action. Choose "Yes" to
use the current image as your customized startup screen. The
capture range is the red rectangular area. Choose "No" to
cancel the screen capture and exit the onscreen display (OSD).
•A message appears, stating that the screen capture is in
progress.
•When the screen capture is finished, the message disappears
and the original display is shown.
•The customized startup screen, as shown below, takes effect
when there is a new input signal or when you restart the
projector.
other signals if the current input signal is lost. When Source Lock is
turned "On", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is selected
and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
related with power on/off of the projector.
during standby mode.
•Press the button and choose "Yes" to return the
parameters on all menus to the factory default settings.
Page 36
26
English
SecuritySecurity
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
•Select "On" to enable the security function. The user has to
•If "Off" is selected, then the user can turn on the projector
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•Press or to select the timeout interval.
•The range is from 10 minute to 990 minutes.
•When the time is up, the projector will prompt the user to
•The factory default setting of "Timeout(Min.)" is "Off".
•Once the security function is enabled, the projector will
User Password
•Press to setup or change the "User Password".
•Press number keys to set your password on the remote control
•Press to delete character.
•Enter the password when you see "Confirm Password"
•The password should be between 4 and 8 characters long.
•If you select "Request password only when plugging the
•If you select "Always request password while projector turns
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•Press to change the "Administrator Password".
•The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
•An unique 6-digit "Universal Password" which is printed on
•If losing this security card and number, please contact with an
enter a password to operate the projector. Please refer to the
"User Password" section for details.
without password.
enter the password again.
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
and press "MENU" to confirm.
displayed.
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
on.", the user has to enter the password every time when the
projector is turned on.
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator Password
is.
Acer service center.
Page 37
English
Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen
is "On", users cannot change startup screen anymore and avoid
other users change that arbitrarily. Choose "Off" to unlock startup
screen.
Note: Functions vary depending on model definition.
Management
27
ECO ModeChoose "On" to dim the projector lamp which will lower power
High AltitudeChoose "On" to turn on High Altitude mode. Operate the fans at
Turn Off Mode•Instant Off: Shuts down the projector without fan cooling.
Auto ShutdownThe projector will automatically shutdown when there is no signal
AC Power OnChoose "On" to power on projector while AC power plug in.
Lamp Hour ElapseDisplays the lamp’s elapsed operating time (in hours).
Lamp RemindingActivate this function to display a reminder to change the lamp 30
Lamp Hour Reset
Note: Functions vary depending on model definition.
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
full speed continuously to allow for proper high altitude cooling of
the projector.
•Instant Resume: Resumes the system when the Power button is
pressed again within 2 minutes.
input after the allocated time. (default is 15 minutes)
hours before its expected end-of-life.
Press the button and choose "Yes" to turn the lamp hour
counter to 0 hours.
Page 38
28
English
Audio
Volume
Mute•Choose "On" to mute the volume.
Power On/Off Volume Select this function to adjust the notification volume when
Alarm VolumeSelect the function to adjust the volume of any warning
Note: Functions vary depending on model definition.
•Press to decrease the volume.
•Press to increase the volume.
•Choose "Off" to restore the volume.
turning the projector on/off.
notifications.
Page 39
English
3D
3DChoose "On" to enable DLP 3D function.
•On: Choose this item while using DLP 3D glasses, 120Hz 3D
capable graphics cards and HQFS format file or DVD with
corresponding SW player.
•Off: Turn off 3D mode.
3D FormatIf the 3D content is not displayed correctly, you can select a 3D
24P 3DChoose "96Hz" or "144Hz" to compatible with 3D glasses.
3D L/R InvertIf you see a discrete or overlapping image while wearing DLP 3D
3D Warning Message Choose "On" to display the 3D warning message.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
- Stereoscopic Player (Trial):
http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
format that suits the 3D content you are viewing and obtain the
best result.
glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).
29
Language
Language
Choose the multilingual OSD menu. Use theorkey
to select your preferred menu language.
•Press to confirm the selection.
Page 40
30
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#ProblemSolution
1No image appears
onscreen
2Partial, scrolling
or incorrectly
displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))
•Connected as described in the "Getting Started"
section.
•Ensure none of the connector pins are bent or
broken.
•Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•Make sure you have removed the lens cap and the
projector is switched on.
•Press "RESYNC" on the control panel.
•For an incorrectly displayed image:
•Open "My Computer", open the "Control
Panel", and then double-click the "Display"
icon.
•Select the "Settings" tab.
•Verify that your display resolution setting is
lower than or equal to WUXGA-RB (1920 x
1200).
•Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•Verify that the resolution setting is lower than
or equal to WUXGA-RB (1920 x 1200).
•Click the "Change" button under the "Monitor"
tab.
•Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA-RB
(1920 x 1200).
Page 41
31
English
3Partial, scrolling
or incorrectly
displayed image
(For notebooks)
4The screen of the
notebook
computer is not
displaying your
presentation
5Image is unstable
or flickering
6Image has vertical
flickering bar
7Image is out of
focus
•Press "RESYNC" on the control panel.
•For an incorrectly displayed image:
•Follow the steps for item 2 (above) to adjust the
resolution of your computer.
•Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment including
the projector.
®
•If you are using a Microsoft
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
•If you are using an Apple
In System Preferences, open Display and select Video
Mirroring "On".
•Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
•Change the display color depth settings on your
computer.
•Use "Frequency" to make an adjustment. Refer to the
"Image" section for more information.
•Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
•Make sure the lens cap is removed.
•Adjusts the focus ring on the projector lens.
•Make sure the projection screen is within the
required distance of 3.3 to 23.3 feet (1.0 to 7.1
meters) from the projector. Refer to the "How to get
a preferred image size by adjusting distance and
zoom" section for more information.
Windows® based
®
Mac® OS based notebook:
8Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following settings:
•If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•If you play an Letterbox (LBX) format DVD title,
please change the format to Letterbox (LBX) in the
projector OSD.
Page 42
32
English
9Image is too small
or too large
10Image has slanted
sides
11Image is reversed•Select "Image --> Projection Mode" on the OSD and
•Adjust the zoom lever on the top of the projector.
•Move the projector closer to or further from the
screen.
•Press "MENU" on the remote control. Go to "Image -> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.
•If possible, reposition the projector so that it is
centered on the screen.
•Press the "Keystone / " button on the remote
control until the sides are vertical.
•Press "MENU" on the remote control. Go to "Image -> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.
adjust the projection direction.
Page 43
English
OSD Messages
#ConditionMessage Reminder
1Message• Fan Fail - the system fan is not working.
• Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed
to cool down before it may be used. Please check the
following message.
Please also check the dust filters if they are installed. If the
dust filter is clogged with dust, please clean it. Please refer to
"Cleaning and replacing the dust filters" for details.
• Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
33
Problems with the Projector
#ConditionSolution
1The projector stops responding
to all controls
2Lamp burns out or makes a
popping sound
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
Page 44
34
English
LED & Alarm Definition Listing
LED Messages
Message
Input power plugFlash ON to
Standby----ON--
Power button ON------ON
Lamp retry------Quick
Power off (Cooling state)----Quick
Power button OFF
(cooling completed;
standby mode)
Error (thermal failure)--ON--ON
Error (fan lock)--Quick
Error (lamp breakdown)ON----ON
Error (color wheel fail)Quick
Lamp_LEDTemp_LEDPower LED
RedRedRedBlue
OFF 100ms
----ON--
Flashing
Flash ON to
OFF 100ms
Flashing
----ON
Flash ON to
OFF 100ms
Flashing
--ON
--
Flashing
--
Page 45
English
How to install cable management
1
3
22
Cable management
AABBCC
I. Ceiling Mount Scenario
1Loosen the screw before removing the cable management cover from
projector. (Illustration #1)
2Carefully slide the clasp with your finger. (Illustration #2)
3Pull out the cable management. (Illustration #3)
4Plug in power cord and other cables you need.
5If you need to install Acer Dongle
(WirlessHD-Kit/WirelessAndroid-Kit/WirelessCAST), follow the below steps:
(A) Install dongle rubber.
(B) Connect dongle to HDMI extension cable port.
(C) Fasten both side of dongle rubber to the specific position of cable
management cover.
(D) Connect to HDMI 1/MHL port on projector.
6Assembly the cable management cover firmly to projector, and tighten the
screw. (Illustration #3,2,1)
35
Page 46
36
English
1
2
II. Table Scenario
If you’d like to put projector on the table, you can use scissors to get rid of
highlighted part, so that all the cables can be through from here (Illustration
#1)
Page 47
37
English
11
2
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
Follow these steps:
1Turn the projector off. Wait for the Power LED to stop flashing then
unplug the power cord.
2Allow the projector at least 30 mins to cool down.
3Pull out the dust filter. (Illustration #1)
4To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipment. (Illustration #2)
5If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
Page 48
38
English
1
2
6
4
5
3
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
2Remove the screw that secure the lamp module. (Illustration #3)
Lift the handle so that it stands up. (Illustration #4)
Pull out the lamp plug. (Illustration #5)
3Lift the handle so that it stands up. Pull out the lamp module by force.
(Illustration #6)
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
Page 49
English
Ceiling Mount Installation
Type 1Type 2Type 3
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1Drill four holes into a solid, structural ceiling member, and secure the
ceiling mount base to the ceiling.
2Choose the length combination based on actual environment. (CM-01S
doesn’t include Type 2 and Type 3.)
39
Page 50
40
English
Type 1:
Type 2:Type 3:
Illustration 1
Illustration 2
3Type 1:
For the standard size use three bracket screws to mount the projector to
the ceiling mount bracket.
Type 2 and Type 3:
Alternatively, for the larger size, use the sliding extensions for more
supports.
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution.
4Connect the main body connector to the projector bracket (illustration 1),
and then screw up four screws (illustration 2).
Page 51
English
5Adjust the angle and positioning as necessary.
360°
85.00 mm55.00 mm
82.30 mm63.81 mm
SCREW SPEC. M4 x 25 mm
Screw Type BWasher Type
Diameter (mm)Length (mm)LargeSmall
425VV
41
Page 52
42
English
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
Projection system
Resolution• 1920x1080 1080p resolution
Computer compatibilityIBM PC and compatibles, Apple Macintosh, iMac and
Video compatibilityNTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
1080i (Top and Bottom)1920x108060 (30)33.8
1080p (Top and Bottom)1920x10802427.0
1080p (Top and Bottom)1920x10805056.3
1080p (Top and Bottom)1920x10806067.5
720p (Side by Side (Half))1280x7206045.0
1080i (Side by Side (Half)) 1920x108050 (25)28.1
1080i (Side by Side (Half)) 1920x108060 (30)33.8
1080p (Side by Side (Half)) 1920x10805056.3
1080p (Side by Side (Half)) 1920x10806067.5
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the device and receiver.
•Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
English
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Page 60
50
English
001
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-247)
aCommon information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
bOperation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm
for the latest country list.
Page 61
We,
of Conformity
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
EN 301 511 V9.0.2
EN 301 908-1 V6.2.1
EN 301 908-2 V6.2.1
EN 301 908-13 V6.2.1
EN 301 489-1 V1.9.2
EN 301 489-3 V1.6.1
Regulation (EC) No. 278/2009; EN 50563:2011
EN 301 489-7 V1.3.1
EN 301 489-17 V2.2.1
EN 301 489-24 V1.5.1
EN 50360:2001 EN 50566:2013
EN 62479:2010 EN 62311:2008
EN 62209-1:2006 EN 62209-2:2010
Year to begin affixing CE marking 2017.
_______________________________
RU Jan / Sr. Manager Date
Acer Incorporated (Taipei, Taiwan)
Jan. 1, 2017
Page 62
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
P
roduct:
DLP
Projector
Model
Number:
D1P1434
Machine Type:
H8550BD/V7500/HV
750/V240/HT-820
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.