Acer Aspire 5336-2524 User manual

Download

Aspire 5336 Series

Service Guide

PRINTED IN TAIWAN

Service guide files and updates are available

on the ACER/CSD web; for more information,

please refer to http://csd.acer.com.tw

Revision History

Please refer to the table below for the updates made on Aspire 5336 service guides.

Date Chapter Updates

III

Copyright © 2010 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Conventions

The following conventions are used in this manual:

NOTE: This symbol where placed in the Service Guide designates a compon ent that should be recycled according to the local regulations.

SCREEN MESSAGES Denotes actual messages that appear

on screen.

NOTE Gives bits and pieces of additional

information related to the current topic.

WARNING Alerts you to any damage that might

result from doing or not doing specific actions.

CAUTION Gives precautionary measures to

avoid possible hardware or software problems.

IMPORTANT Reminds you to do specific actions

relevant to the accomplishment of procedures.

Preface

Before using this information and the product it supports, please read the following general informati on.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

VII

Table of Contents

System Specifications 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Closed Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Base View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

System Utilities 27

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Aspire 5336 BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Remove HDD/BIOS Password Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Machine Disassembly and Replacement 43

Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Removing the SD Dummy Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Removing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Removing the Logic Lower Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Removing the DIMM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Removing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Removing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Removing the Touchpad FFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Removing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

VIII

Table of Contents

Removing the Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Removing the ODD Connector Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Removing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Removing the LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Removing the DC-IN Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Removing the LCD/LED Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Removing the LCD Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Removing the LVDS cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Removing the Microphone Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Replacing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Replacing the Microphone Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Replacing the LVDS Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Replacing the LCD Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Replacing the LCD/LED Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Replacing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

Replacing the DC-IN Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

Replacing the LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114

Replacing the ODD Connector Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117

Replacing the Bluetooth Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Replacing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

Replacing the Touchpad FFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121

Replacing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Replacing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123

Replacing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124

Replacing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128

Replacing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129

Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131

Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132

Replacing the Lower Logic Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133

Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134

Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136

Replacing the SD Dummy Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138

Troubleshooting 139

Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139

Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140

No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141

Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142

LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143

Table of Contents

Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143

Touchpad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144

Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144

HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146

ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147

Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150

Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150

External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151

Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151

Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152

Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152

Post Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153

Jumper and Connector Locations 157

Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157

Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158

Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159

USB/B Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

ODD Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160

Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

Clear CMOS Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161

BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162

FRU (Field Replaceable Unit) List 163

Aspire 5336 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164

Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164

Upper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165

LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166

LED Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167

Aspire 5336 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168

Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187

Model Definition and Configuration 188

AS5336 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188

Test Compatible Components 209

Microsoft® Windows® 7 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210

Online Support Information 215 Index 217

Table of Contents

Chapter 1 1

System Specifications

Features

Below is a brief summary of the computer’s many features: NOTE: Items denoted with an (*) are only available for selected models.

Operating System

• Genuine Windows® 7 Home Premium 64-bit

• Genuine Windows® 7 Home Basic 64 -b i t

Platform

• Intel® Celeron® processor T3500 (1 MB L2 cache, 2.10 GHz, 800 MHz FSB, 35 W), supporting Intel® 64 architecture

• Intel® Celeron® processor 900 (1 MB L2 cache, 2.20 GHz, 800 MHz FSB, 35 W), supporting Intel® 64 architecture

• Mobile Intel® GL40 Express Chipset

System Memory

• Dual-channel DDR3 SDRAM support:

• Up to 2 GB of DDR3 system memory, upgradable to 4 GB using two soDIMM modules

Display

• 15.6" HD 1366 x 768 pixel resolution, high-brightness (200-nit) Acer CineCrystal™ TFT LCD, supporting simultaneous multi-window viewing

• 16:9 aspect ratio

Graphics

• Mobile Intel® GL40 Express Chipset with integrated 3D graphics, featuring Intel® Graphics Media Accelerator 4500M (Intel® GMA 4500M) with up to 1759 MB of Intel® Dynamic Video Memory Technology 5.0 (64 MB of dedicated system memory, up to 1695 MB of shared system memory), supporting Microsoft® DirectX® 10

• Dual independent display support

• 16.7 million colors

• External resolution / refresh rates:

• VGA port up to 2048 x 1536: 60 Hz

• HDMI™ port up to 1728 x 1080: 60 Hz

• MPEG-2/DVD decoding

• WMV9 (VC-1) and H.264 (AVC) decoding

• HDMI™ (High-Definition Multimedia Interface) with HDCP (High-bandwidth Digital Content Protection) support

Chapter 1

2 Chapter 1

Audio

• Built-in mono speaker

• Built-in microphone

• MS-Sound compatible

Storage

• Hard disk drive:

• 160/250/320/500/640 GB or larger

• 2-in-1 card reader, supporting:

• Secure Digital™ (SD), MultiMediaCard™ (MMC)

Optical Media Drive

• 8X DVD-Super Multi double-layer drive:

• Read: 24X CD-ROM, 24X CD-R, 24X CD-RW, 8X DVD-ROM, 8X DVD-R, 8X DVD+R, 6X

DVD-ROM DL, 6X DVD-R DL, 6X DVD+R DL, 6X DVD-RW, 6X DVD+RW, 5X DVD-RAM

• Write: 24X CD-R, 16X CD-RW, 8X DVD-R, 8X DVD+R, 4X DVD-R DL, 4X DVD+R DL, 6X

DVD-RW, 8X DVD+RW, 5X DVD-RAM

Communication

• Acer Video Conference, featuring:

• Acer Crystal Eye webcam with 1280 x 1024 resolution

•WLAN:

• Acer InviLink™ Nplify™ 802.1 1b/g/n Wi-Fi CERTIFIED™

• Acer InviLink™ 802.11b/g Wi-Fi CERTIFIED™

• Supporting Acer SignalUp™ wireless technology

•WPAN:1

• Bluetooth® 3.0+HS

• Bluetooth® 2.1+EDR

•LAN:

• Gigabit Ethernet, Wake-on-LAN ready

Privacy Control

• BIOS user, supervisor, HDD passwords

• Kensington lock slot

Dimensions and Weight

• Dimensions

• 381 (W) x 253 (D) x 25/34 (H) mm (14.99 x 9.96 x 0.98/1.33 inches)

• Weight

• 2.6 kg (5.74 lbs.) with 6-cell battery pack

Chapter 1 3

Power Subsystem

ACPI 3.0 CPU power management standard: supports Standby and Hibernation power-saving modes

Power adapter

• 3-pin 65 W AC adapter:

• 108 (W) x 46 (D) x 29.5 (H) mm (4.25 x 1.81 x 1.16 inches)

• 225 g (0.49 lbs.) with 180 cm DC cable

Battery

• 48.8 Wh 4400 mAh 6-cell Li-ion standard battery pack

• Battery life: 3.5 hours

• 41.4 Wh 2800 mAh 4-cell Li-ion standard battery pack

• Battery life: 3 hours

• ENERGY STAR®

Special Keys and Controls

• Keyboard

• 103-/104-/107-key Acer FineTip keyboard with independent standard numeric keypad,

international language support

• Touchpad

• Multi-gesture touchpad, supporting two-finger scroll, pinch, rotate, flip

• Media keys

• Media control keys (printed on keyboard): play/pause, stop, previous, next, volume up,

volume down

I/O Interface

• 2-in-1 card reader (SD™, MMC)

• Three USB 2.0 ports

• HDMI™ port with HDCP support

• External display (VGA) port

• Headphone/speaker/line-out jack

• Microphone-in jack

• Ethernet (RJ-45) port

• DC-in jack for AC adapter

Software

• Productivity

• Acer Backup Manager

• Acer ePower Management

• Acer eRecovery Management

• Adobe® Flash® Player 10.1

• Adobe® Reader® 9.1

•eSobi™

• Google Toolbar™

4 Chapter 1

• Microsoft® Office 2010 preloaded (purchase a product key to activate)

• Microsoft® Office Starter 2010

• Norton™ Online Backup

• Security

• McAfee® Internet Security Suite Trial

• MyWinLocker® (except China, Hong Kong)

• Multimedia

• Cyberlink® PowerDVD™

• NTI Media Maker™

•Gaming

• Oberon GameZone (except US, Canada, Hong Kong, Korea)

• WildTangent®1 (US, Canada only)

• Communication and ISP

• Acer Crystal Eye

• Microsoft® Silverlight™

• Skype™

• Windows Live™ Essentials - Wave 3.2 (Mail, Photo Gallery, Live™ Messenger, Movie Maker,

Writer)

• Web links and utilities

• Acer Accessory Store (Belgium, France, Germany, Italy, Netherlands, Spain, Sweden, UK

only)

• Acer Identity Card

• Acer Registration

• Acer Updater

• eBay® shortcut 2009 (Canada, France, Germany, Italy, Mexico, Spain, UK, US only)

• Netflix shortcut (US only)

Optional Items

• 1 / 2 GB DDR3 soDIMM module

• 3-pin 65 W AC adapter

• 6-cell Li-ion battery pack

• External USB floppy disk drive

Environment

• Temperature:

• Operating: 5 °C to 35 °C

• Non-operating: -20 °C to 65 °C

• Humidity (non-condensing):

• Operating: 20% to 80%

• Non-operating: 20% to 80%

Chapter 1 5

System Block Diagram

(Socket P)

LCD Conn.

RTC CKT.

3.3V 24.576MHz/48Mhz

TMDS

HDMI Level S hift

HDMI Conn.

CMOS Cam era

MINI Card x1

LAN Broadcom BCM57780

PCI -E xp ress

WLAN

Dual Channel

Po wer On /Off CKT.

Phon e Jack x2

H_D#(0..6 3)H_A#(3..35)

uFCBGA-1329

LPC BUS

CRT Conn.

Touch Pad

BANK 0, 1, 2, 3

Int.KBD

Clock Generator

RJ45

FSB

3.3V 48MHz

Intel Penryn P rocessor

DC/DC In terfac e CKT.

DMI

ALC272X

667/800/1066MHz

USB conn x1

Intel Cantiga

204pin DDRIII-SO-DIMM X2

uPGA-478 Package

Powe r Circuit DC/D C

Fan Control

ICS9LPRS387

BGA-676

Memory BUS(DDRIII)

HDA Codec

1.5V DDRIII 800/1066

BIOS

ENE KB926 E0

Thermal Sensor

Intel ICH9-M

HD Audio

C-Lin k

ODD/B Conn.

LS-6583P

Audio AMP

USB port 0

Card Reader Realtek RTS5137

USB/B Conn.

LS-6582P

Small Board

EMC 1402

Bluetooth Con n

LS-6581P

S-ATA

port 0

SATA HDD Conn.

POWER/B Conn.

LVDS

USB

6 Chapter 1

Your Acer Notebook tour

Front View

No. Icon Item Description

1 Integrated

Webcam

Web camera for video communication (for selected models).

2 Display screen Also called Liquid-Crystal Display (LCD),

displays computer output.

3 HDD Indicates when the hard disk drive is active.

Communication indicator

Indicates the computer’s wireless connectivity device status.

4 Power button Turns the computer on and off.

5 Keyboard For entering data into your computer. 6

Power

Indicates the computer’s power status.

Battery

Indicates the computer’s battery status.

1. Charging: The light shows amber when the battery is charging.

2. Fully charged: The light shows blue when in AC mode.

Chapter 1 7

NOTE: The front panel indicators are visible even when the computer cover is closed.

Closed Front View

Closed Rear View

7 Click buttons (left

and right)

The left and right buttons function like the left and right mouse buttons.

8 T ouchpad T ouch-sensitive pointing device which functions

like a computer mouse.

9 Speakers Left and right speakers deliver stereo audio

output.

10 Microphone Internal microphone for recording sound.

No. Icon Item Description

1 2-in-1 card

reader

Accepts Secure Digital (SD), MultiMediaCard (MMC).

Note: Push to remove/install the card. Only one card can operate at any given time.

No. Icon Item Description

1 Battery bay Houses the computer's battery pack.

No. Icon Item Description

8 Chapter 1

Left View

Right View

No. Icon Item Description

1 DC-in jack Connects to an AC adapter

2 External display

(VGA) port

Connects to a display device (e.g. external monitor, LCD projector).

3 Ethernet (RJ-45)

port

Connects to an Ethernet 10/100/1000-based network.

4 HDMI Connect to HDMI devices 5 USB 2.0 ports Connect to USB 2.0 devices (e.g. USB mouse,

USB camera).

6 Microphone-in

jack

Accepts input from external microphones.

Headphones/ speaker/line-out jack

Connects to audio line-out devices (e.g. speakers, headphones).

No. Icon Item Description

1 USB 2.0 ports Connect to USB 2.0 devices (e.g. USB mouse, USB

camera). 2 Optical drive Internal optical drive; accepts CDs or DVDs. 3 Optical disk access

indicator

Lights up when the optical drive is active.

4 Optical drive eject

button

Ejects the optical disk from the drive.

5 Emergency eject hole Ejects the optical drive tray when the computer is

turned off.

Note: Insert a paper clip into the emergency eject

hole to eject the optical drive tray when the computer

is off. 6 Kensington lock slot Connects to a Kensington-compatible computer

security lock.

Note: Wrap the computer security lock cable around

an immovable object such as a table or handle of a

locked drawer. Insert the lock into the notch and turn

the key to secure the lock. Some keyless models are

also available.

265431

213456

Chapter 1 9

Base View

Indicators

The computer has several easy-to-read status indicators.

No. Icon Item Description

1 Battery bay Houses the computer's battery pack.

2 Battery release

latch

Releases the battery for removal.

3 Hard disk bay Houses the computer's hard disk (secured

with screws).

Memory compartment

Houses the computer's main memory.

4 Battery lock Locks the battery in position.

Icon Function Description

Power Indicates the computer's power status.

Battery Indicates the computer's battery status.

NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.

HDD Indicates when the hard disk drive is active.

Communication indicator Indicates the computer’s wireless connectivity

device status.

10 Chapter 1

Touchpad Basics

The following items show you how to use the Touchpad:

• Move your finger across the Touchpad (1) to move the cursor.

• Press the left (2) and right (3) buttons located beneath the Touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the Touchpad is the same as clicking the left button.

NOTE: When using the Touchpad, keep it - and your fingers - dry and clean. The Touchpad is sensitive to

finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not increase the Touchpad’s responsiveness.

Function Left Button (2) Right Button (3) Main Touchpad (1)

Execute Quickly click twice. Tap twice (at the same speed

as double-clicking a mouse

button). Select Click once. Tap once. Drag Click and hold, then use

finger on the Touchpad to drag the cursor.

Tap twice (at the same speed

as double-clicking a mouse

button); rest your finger on

the Touchpad on the second

tap and drag the cursor. Access

context menu

Click once.

Chapter 1 11

Using the Keyboard

The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys.

Lock Keys and embedded numeric keypad

The keyboard has two lock keys which you can toggle on and off.

Lock key Description

Caps Lock When Caps Lock is on, all alphabeti c characters typed are in uppercase. Scroll Lock When Scroll Lock is on, the contents of a text window scroll without moving the

cursor.

Num Lock When Num Lock is on, the embedded keypad is in numeric mode.

12 Chapter 1

Windows Keys

The keyboard has two keys that perform Windows-specific functions.

Key Description

Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;

it launches the Start menu. It can also be used with other keys to provide a variety of functions:

<>: Open or close the Start menu <> + <D>: Display the desktop <> + <E>: Open Windows Explore <> + <F>: Search for a file or folder <> + <G>: Cycle through Sidebar gadgets <> + <L>: Lock your computer (if you are connected to a network domain), or

switch users (if you're not connected to a network domain)

<> + <M>: Minimizes all windows <> + <R>: Open the Run dialog box <> + <T>: Cycle through programs on the taskbar <> + <U>: Open Ease of Access Center <> + <X>: Open Windows Mobility Center <> + <BREAK>: Display the System Properties dialog box <> + <SHIFT+M>: Restore minimized windows to the desktop <> + <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D <> + <SP ACEBAR>: Bring all gadgets to the front and select Windows Sidebar

<CTRL> +

<> + <F>: Search for computers (if you are on a network)

<CTRL> + <> + <TAB>: Use the arrow keys to cycle through programs on the

taskbar by using Windows Flip 3-D

Note: Depending on your edition of Windows 7, some shortcuts may not function as

described.

Application key

This key has the same effect as clicking the right mouse button; it opens the application's context menu.

Chapter 1 13

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility.

To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

Hotkey Icon Function Description

<Fn> + <F3> Communication key Enables / disables the computer's

communication devices. (Communication devices may vary by configuration.)

<Fn> + <F4> Sleep Puts the computer in Sleep mode.

<Fn> + <F5> Display toggle Switches display output between the display

screen, external monitor (if connected) and both.

<Fn> + <F6> Display Off Turns the display screen backlight off to save

power. Press any key to return.

<Fn> + <F7> Touchpad toggle Turns the internal touchpad on and off.

<Fn> + <F8> Speaker toggle Turns the speakers on and off.

Brightness up Increases the screen brightness.

Brightness down Decreases the screen brightness.

Volume up Increases the sound volume.

Volume down Decreases the sound volume.

<Fn> + <Home> Play/Pause Play or pause a selected media file.

<Fn> + <Pg Up> Stop Stop playing the selected media file.

<Fn> + <Pg Dn> Previous Return to the previous media file.

<Fn> + <End> Next Jump to the next media file.

14 Chapter 1

Hardware Specifications and Configurations

Processor

Processor Specifications

CPU Fan True Value Table (TJ105)

• Throttling 50%: On= 95C; OFF=80C

• OS shut down at 100C; H/W shut down at 90C

BIOS

Item Specification

CPU type Intel® Pentium® and Intel® Celeron® mobile processors CPU package Micro- FCPGA package Core Logic Intel Montevina chipset

ICH9M Intel 82801GBM On die 512-kB, 8-way L2 cache

Chipset Intel® GL40 Express Chipset

Item

CPU

Speed

Cores

Bus

Speed

Cache

Size

Package

Core

Voltage

Acer PN

CM900 2.2G 2 800MHz 1M Micro-

FCPGA

1.0V -

1.2V

KC.N0001.900

T3500 21.G 2 800MHz 1M Micro-

FCPGA

0.8V-

1.25V

KC.35001.CMT

CPU Temperature Fan Speed (RPM) SPL Spec (dBA)

50 2300 28 55 2500 31 60 2700 34 65 3000 37 85 3300 40

Item Specification

BIOS vendor InsydeH20 BIOS Version V1.0 BIOS ROM type Flash BIOS ROM size 2 MB Features Support ISIPP

Support Acer UI Support multi-boot Suspend to RAM (S3)/Disk (S4) Various hot-keys for system control Support SMBUS 3.0, PCI3.0 ACPI 3.0b compliance with Intel Speed Step Support C1, C2,

C3, C4 and S3, S4 for mobile CPU DMI utility for BIOS serial number configurable/asset tag Support PXE Support Y2K solution Support Win Flash Wake on LAN from S3 Wake on LAN from S4 in AC mode System information

Chapter 1 15

System Memory

Memory Combinations

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various

capacities to form other combinations. In the above table, the configuration of slot 1 and slot 2 could be reversed.

Hard Disk Drive Interface

Item Specification

Memory controller Built in (Intel® GL40 Express Chipset) Memory size 512MB,1GB,2GB DDR3 RAM DIMM socket number 2 Supports memory size per socket 2 GB Supports maximum memory size 4 GB Supports DIMM type DDR III 667/800Mhz SDRAM memory interface design Supports DIMM Speed 667/800Mhz SDRAM Support DIMM voltage 1.5V Supports DIMM package DDRIII SDRAM 204pin Unbuffered SODIMM based

Slot 1 Slot 2 Total Memory

0MB 1024MB 1024MB 0MB 2048MB 2048MB 1024MB 0MB 1024MB 1024MB 1024MB 2048MB 1024MB 2048MB 3072MB 2048MB 0MB 2048MB 2048MB 1024MB 3072MB 2048MB 2048MB 4096MB

Item Specification

Vendor & Model Name

WD WD1600BEVT-

22A23T0

HITACHI HTS545016B9A300

SEAGATE ST9160314AS

TOSHIBA MK1665GSX

Capacity (GB) 160GB Bytes per sector 512Bytes Data heads 1 2 2 1 Drive Format Disks 1 Spindle speed

(RPM)

5400

Performance Specifications Buffer size 8 MB Interface SATA Fast data transfer

rate (Mbits/sec, max)

3.0Gbits/s

Media data transfer rate

(Mbytes/sec max)

106MBytes/s 845Mbits/s 1175Mbits/s 1273.3Mbits/s

DC Power Requirements Voltage tolerance 5V

16 Chapter 1

Item Specification

Vendor & Model Name

WD WD2500BEVT-

22A23T0

HITACHI HTS545025B9A300

SEAGATE ST9250315AS

TOSHIBA MK2565GSX

Capacity (GB) 250GB Bytes per sector 512Bytes Data heads 2 Drive Format Disks 1 Spindle speed

(RPM)

5400

Performance Specifications Buffer size 8 MB Interface SATA Fast data transfer

rate (Mbits/sec, max)

3.0Gbits/s

Media data transfer rate

(Mbytes/sec max)

106MBytes/s 875Mbits/s 1175Mbits/s 1031.7Mbits/s

DC Power Requirements Voltage tolerance 5V

Item Specification

Vendor & Model Name

WD WD3200BEVT-

22A23T0

HITACHI HTS545032B9A300

SEAGATE ST9320315AS

TOSHIBA MK3265GSX

Capacity (GB) 320GB Bytes per sector 512Bytes Data heads 2 3 3 2 Drive Format Disks 1 2 2 1 Spindle speed

(RPM)

5400

Performance Specifications Buffer size 8 MB Interface SATA Fast data transfer

rate (Mbits/sec, max)

3.0Gbits/s

Media data transfer rate

(Mbytes/sec max)

106MBytes/s 875Mbits/s 1175Mbits/s 1273.3Mbits/s

DC Power Requirements Voltage tolerance 5V

Chapter 1 17

Item Specification

Vendor & Model Name

WD WD5000BEVT-

22A0RT0

HITACHI HTS545050B9A300

SEAGATE ST9500325AS

TOSHIBA MK5065GSX

Capacity (GB) 500GB Bytes per sector 512Bytes Data heads 4 Drive Format Disks 2 Spindle speed

(RPM)

5400

Performance Specifications Buffer size 8 MB Interface SATA Fast data transfer

rate (Mbits/sec, max)

3.0Gbits/s

Media data transfer rate

(Mbytes/sec max)

106MBytes/s 875Mbits/s 1175Mbits/s 1031.7Mbits/s

DC Power Requirements Voltage tolerance 5V

Item Specification

Vendor & Model Name

WD WD6400BEVT-

22A0RT0

TOSHIBA MK6465GSX

WD WD7500BPVT-

22HXZT1

WD WD3200BPVT-

22ZEST0 Capacity (GB) 640GB 750GB 320GB Bytes per sector 512Bytes 4096Bytes Data heads 4 2 Drive Format Disks 2 1 Spindle speed

(RPM)

5400

Performance Specifications Buffer size 8 MB Interface SATA Fast data transfer

rate (Mbits/sec, max)

3.0Gbits/s 3.0Gbits/s 3.0Gbits/s 3.0Gbits/s

Media data transfer rate

(Mbytes/sec max)

106MBytes/s 1273.3Mbits/s 97MBytes/s 108MBytes/s

DC Power Requirements Voltage tolerance 5V

18 Chapter 1

Super-Multi Drive Interface

BD Drive Interface

Item Specification

Vendor & model name HLDS Super-Multi Drive DL 8X GT32N LF, SONY Super-Multi Drive DL

8X AD-7585H LF, TSST Super-Multi Drive DL 8X TS-L633F, Panasoni c Super-Multi Drive DL 8X UJ8A0, PLDS Super-Multi Drive DL 8X DS-

8A5SH, SONY Super-Multi Drive DL 8X AD-7580S LF Performance Specification With CD Diskette With DVD Diskette Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Sustained: Max 10.08Mbytes/sec Buffer Memory 2MB Interface SATA Applicable disc format Applicable disc format CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD

(multi-session), Video CD, Cd-Extra (CD+), CD-text DVD: DVD-VIDEO,

DVD-ROM, DVD-R (3.9GB, 4.7GB) DVD-R DL, DVD-RW, DVD-RAM,

DVD+R, DVD+R DL, DVD+RW CD: CD-DA (Red Book) - Standard Audio

CD & CD-TEXT CD-ROM (Yellow Book Mode1 & 2) - Standard Data CD-

ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session CD-I (Green

Book, Mode2 Form1 & 2, Ready, Bridge) CD-Extra/ CD-Plus (Blue Book)

- Audio & Text/Video Video-CD (White Book) - MPEG1 Video CD-R

(Orange Book Part) CD-RW & HSRW (Orange Book Part Volume1 &

Volume 2 Super Audio CD (SACD) Hybrid type US & US+ RW DVD:

DVD-ROM (Book 1.02), DVD-Dual DVD-Video (Book 1.1) DVD-R (Book

1.0, 3.9G) DVD-R (Book 2.0, 4.7G) - General & Authoring DVD+R

(Version 1.0) DVD+RW DVD-RW (Non CPRM & CPRM) DVD°"R Dual Loading mechanism Load: Manual Release: (a) Electrical Release (Release Button) (b)

Release by ATAPI command (c) Emergency Release Power Requirement Input Voltage 5 V +/- 5% (Operating)

Item Specification

Vendor & model name HLDS BD COMBO DRIVE TRAY DL 4X CT10 LF, PANASONIC BD COMBO

12.7mm Tray DL 4X UJ-130A

Performance Specification

With CD Disc

Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Buffer Memory 2MB Interface SATA Applicable disc format Applicable disc format CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD (multi-

session), Video CD, Cd-Extra (CD+), CD-text DVD: DVD-VIDEO, DVD-ROM, DVD-R (3.9GB, 4.7GB) DVD-R DL, DVD-RW, DVD-RAM, DVD+R, DVD+R DL, DVD+RW CD: CD-DA (Red Book) - Standard Audio CD & CD-TEXT CDROM (Yellow Book Mode1 & 2) - Standard Data CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge) CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video-CD (White Book)

- MPEG1 Video CD-R (Orange Book Part) CD-RW & HSRW (Orange Book Part Volume1 & V olume 2 Super Audio CD (SACD) Hybrid type US & US+ RW DVD: DVD-ROM (Book 1.02), DVD-Dual DVD-Video (Book 1.1) DVD-R (Book

1.0, 3.9G) DVD-R (Book 2.0, 4.7G) - General & Authoring DVD+R (Version

1.0) DVD+RW DVD-RW (Non CPRM & CPRM) DVD+/-R Dual Blu-Ray: BD-R, BD-R DL, BD-RE, BD-RE DL

Loading mechanism Load: Manual Release: (a) Electrical Release (Release Button) (b) Release by

ATAPI command (c) Emergency Release Power Requirement Input Voltage 5 V +/- 5% (Operating)

Chapter 1 19

LAN Interface

Wireless Module 802.11b/g/n

Bluetooth Interface

3G (Not available in this model)

Item Specification

LAN Chipset BCM57780 Support LAN protocol x1 PCIe v1.1 bus interface LAN connector type RJ45 LAN connector location Left side Features • Integrated 10/100/1000BASE-T transceiver

• Automatic MDI crossover function

• PCIe v1.1 compliant

• 10/100/1000BASE-T full-duplex/half-duplex MAC

• Receive side scaling (RSS) for multicore processo rs

• Complies with IEEE 802.3, 802.3u, 802.3ab, and 802.1p

• Supports iSCSI boot

• IPv4 and IPv6 large send off load and checksum off load (LSO/TCO)

• Wake on LAN (WOL) support meeting the ACPI requirements

• Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (IEEE 802.3z, Clause 30)

• Self-boot feature, utilizing smaller EEPROM size with ability to use on-chip memory

• PCI Express® CLKREQ support

• Integrated switching regulator for improved power consumption

Item Specification

Chipset Atheros HB93/HB95/ HB97, BCM943225/ BCM4312, RTL 8192 Data throughput 11~54 Mbps, up to 270 Mbps for Draft-N Protocol 802.11 b+g, Draft-N Interface PCI bus (mini PCI socket for wireless module)

Item Specification

Chipset Atheros AR3011, Broadcom BCM2070/, Broadcom BCM2046 Data throughput TX 1.2Mbits/sec

RX 1.2Mbits/sec Protocol 3.0+HS Interface USB 2.0 Connector type SM08B-SURS-TF/JST SM06B-XSRK-ETB/SM08B-SURS-TF

Item Specification

20 Chapter 1

Audio Subsystem

Video Interface

VRAM (not available in this model)

Item Specification

Audio Codec Chipset Realtek ALC272 Package 48-pin LQFP 'Green' package Speaker Amplifier TPA6017A Audio Port Internal 1 mic, 1 speaker Compatibility Dolby® Digital Live, DTS® CONNECT™, Dolby® Home Theater, and SRS®

programs Sampling Rate 44.1k/48k/96k/192kHz External Mic jack

Headphone jack

Item Specification

Chipset Built in Intel Cantiga GL40 Package FCBGA1329 Interface LVDS / CRT

DVI (Docking only)

Compatibility 1366x768/60Hz(16:9) / 1280x720/60Hz(16:9) / 1024x768/

60Hz(4:3) / 800x600/60Hz(4:3) Sampling rate 60Hz Supports • Intel Gen 5.0 integrated graphics engine with 10 fully

programmable cores

• 400-MHz core render clock at 1.05-V core voltage

• Supports iHDMI/DVI, LVDS, CRT

• Intel® Dynamic Video Memory Technology (Intel® DVMT

5.0)

• Video Capture via x1 concurrent PCI Express port

• PAVP (Protected Audio-Video Path) support for Protected Intel® HD Audio (Video and Audio) Playback

• High performance MPEG-2 decoding

• WMV9 (VC-1) and H.264 (AVC) support

• Hardware acceleration for MPEG2 VLD/iDCT

• Microsoft DirectX10 support

• Blu-ray support @ 40 Mb/s

• Hardware motion compensation

• Intermediate Z in classic rendering

Item Specification

Chipset Memory size Interface

Chapter 1 21

USB Port

HDMI Port

PCMCIA Port (Not available in this model)

System Board Major Chips

Item Specification

USB compliance level USB2.0 EHCI 2 Number of USB port(s) 3 Location 1 left side, 2 right side

Item Specification

Compliance level HDMI1.4a Number of HDMI port(s) 1 Location Left side

Item Specification

PCMCIA controller Supports card type Number of slots Access location Supports ZV (Zoomed Video) port Supports 32-bit CardBus

Item Specification

Northbridge Intel® GL40 Express Chipset Southbridge Intel ICH9M VGA Built-in Intel® GL40 Express Chipset LAN BCM57780 USB 2.0 Built-in Intel® GL40 Express Chipset Super I/O controller N/A Bluetooth Broadcom 2046/2070, Atheros 3011 Wireless Broadcom 4312/43225, Atheros HB93/HB95/HB97,

Realtek 8192 PCMCIA N/A Audio codec Realtek ALC272X-GR Card reader Realtek RTS5137-GR

22 Chapter 1

Keyboard

I/O Ports

Battery

Item Specification

Type New Acer AC7T flat keyboard Total number of keypads 103-US/104-UK keys Windows logo key Yes Internal & external keyboard work

simultaneously

Yes

Features • Phantom key auto detect

• Overlay numeric keypad

• Support independent pgdn/pgup/pgup/home/end keys

• Support reverse T cursor keys

• Factory configurable different languages by OEM customer

Item Specification

I/O support • 1 x 2 in1 Card reader (SD/MMC)

• 3 x USB 2.0 ports

• 1 x HDMI™ port

• 1 x external CRT

• 1 x Headphone

• 1 x MIC

• 1 x RJ-45

• 1 x DC-in jack

Item Specification

Vendor & model name SANYO AS2010D31

SIMPLO AS10D71/75 SONY AS2010D41 SAMSUNG AS2010D6 PANASONIC AS10D51

PANASONIC AS10D56

Battery Type Li-ion Li-ion Pack capacity 2200 mAh 3000 mAh Number of battery cells 6 4 Package configuration 3S2P 4S1P

Chapter 1 23

LED 15.6"

CCFL 15.6"

Item Specification

Vendor/model name

AUO B156XW 02 V2 (HW:4A)

LG LP156W H2-TLEA

CMO N156B6L0B

BOE HT156W XB-500

CPT CLAA15 6WB11A

SAMSUNG LTN156AT0 2-A04

Screen Diagonal (mm) 394.91 mm Active Area (mm) 344.23 mm x 193.54 mm Display resolution (pixels) 1366 x 3(RGB) x 768 Pixel Pitch (mm) 0.252mm × 0.252 mm Pixel Arrangement R.G.B Vertical Stripe Display Mode Normally White Typical White Luminance (cd/

m2) also called Brightness

220 cd/m2

Contrast Ratio 500: 1 Response Time (Optical Rise

Time/Fall Time) msec

8 ms

Typical Power Consumption (watt)

5.15 W

Weight (without inverter) 460 g Physical Size (mm) 360 mm x 210mm x 5.5 max Electrical Interface 1 channel LVDS Viewing Angle (degree)

Horizontal (Right) CR = 10 (Left)

Vertical (Upper) CR = 10 (Lower)

40 (Right) / 40 (Left) / 10 (Upper) / 30 (Lower)

Item Specification

Vendor/model name AUO

B156XW01 V2

LG LP156WH1TLC1

CMO N156B3L0B

SAMSUNG LTN156AT01-

A01 Screen Diagonal (mm) 394.91 mm Active Area (mm) 344.23 mm x 193.54 mm Display resolution (pixels) 1366 x 3(RGB) x 768 Pixel Pitch (mm) 0.252mm × 0.252 mm Pixel Arrangement R.G.B Vertical Stripe Display Mode Normally White Typical White Luminance (cd/

m2) also called Brightness

220 cd/m2

Contrast Ratio 500: 1 Response Time (Optical Rise

Time/Fall Time) msec

8 ms

Typical Power Consumption (watt)

6.5 W

Weight (without inverter) 510 Physical Size (mm) 360 mm x 210mm x 6.2 max Electrical Interface 1 channel LVDS Viewing Angle (degree)

Horizontal (Right) CR = 10 (Left)

Vertical (Upper) CR = 10 (Lower)

40 (Right) / 40 (Left) / 10 (Upper) / 20 (Lower)

24 Chapter 1

LCD Inverter (LCD Only)

Graphic Driver Supported Resolution

Camera

AC Adapter

Item Specification

Vendor & model name DARFON

VK.21071.804

YEC YNV-C01ACs

Brightness conditions PWM signal frequency: Min142Hz Typ:150Hz Max:158Hz

PWM signal amplitude: Min:3.0V Typ:3.3V Max:3.6V

Duty=Ton/Period: Min:15% Max:100% Input voltage (v) Min:9V Typ:20V Max:20V Input current (mA) Typ:0.33A Output voltage (V, RMS) Typ:650V Output current (mA, RMS) 3.0mA~6.8mA(DAC=0V) 2.7mA~6.3mA(DAC=1V) Output voltage frequency (KHz) Min:45KHz Typ:55KHz Max:65KHz

Resolution 16 bits 32 bits

800x600p/60Hz 16:9 Yes Yes 1024x768p/60Hz 16:9 Yes Yes 1280x600/60Hz 16:9 Yes Yes 1280x720/60Hz 16:9 Yes Yes 1280x768/60Hz 16:9 Yes Yes 1360x768/60Hz 16:9 Yes Yes 1366x768/60Hz 16:9 Yes Yes

Item Specification

Vendor and model Chicony CH9665AL(CNF9155) Type 1.3M Interface USB 2.0 Focusing distance >26.6cm Dimensions (L x W x H mm) 65.3x8.1x3.8mm Sensor type SOC Pixel resolution 1280x1024 Pixel size 2 µm x 2 µm Image size 3.89mm(H) x 2.43mm(V)

Item Specification

Input rating 65W Maximum input AC current 1.5A at 100V~240V Inrush current I2t at 264V Efficiency Refer to EPA 5.0

Chapter 1 25

Card Reader

System LED Indicator

Power Specification

Item Specification

Chipset Realtek RTS5137-GR Package 24 Pin QFN Feature 2-in-1 card reader, supporting:

• Secure Digital™ (SD) Card, MultiMediaCard™ (MMC)

Supports Maximum size (please specify max supporting size for each card)

SD version 3.0 SDXC up to 2TB with High Speed (HS) mode

Item Specification

System state • Blue color solid on: System on

• Blue color and amber color off: System off

• Amber color blinking: S3 state HDD access state Reflects the activities of the HDD or card reader access Wireless state Amber color if a wireless device is active Power button backlight • Blue color solid on: System on

• Blue color off: System off Battery state Charging

• Amber solid on - Battery charging with AC

• Blue color solid on - Battery full

• Amber blinking - Battery abnormal stop charge or batter in

low power state

Discharging

• Amber and blinking - Battery in critical low state

• Amber color off - Discharging state

Legacy

Mode

ACPI Mode Power Management

Off

Mech. Off (G3) All devices in the system are turned off completely. Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned off

completely.

Working (G0/S0) Individual devices such as the CPU and hard disk may be power

managed in this state.

S3 Sleeping State CPU set power down

VGA suspend PCMCIA suspend Audio power down Hard Disk power down CD-ROM power down Super I/O low power mode

S4 Sleeping State Also called Hibernate state. The system saves all system states

and data onto disk prior to powering off the whole system.

26 Chapter 1

Chapter 2 27

System Utilities

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System).

Y our computer is already properly configured and optimized, and you do not need to run this utility . However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.

To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted on the bottom of screen).

The default parameter of F12 Boot Menu is set to “disabled”. If you want to change boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.

Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility.

Navigating the BIOS Utility

There are five menu options: Information, Main, Security, Boot, and Exit. Follow these instructions:

• To choose a menu, use the left and right arrow keys.

• To choose an item, use the up and down arrow keys.

• To change the value of a parameter, press F5 or F6.

• Press Esc while you are in any of the menu options to go to the Exit menu.

• In any menu, you can load default settings by pressing F9. You can also press F10 to save any changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a

particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific Help part of the screen. Read this carefully when making changes to parameter values. Please note that system information is subject to different models.

Chapter 2

28 Chapter 2

Aspire 5336 BIOS

Information

The Information screen displays a summary of the computer hardware information.

NOTE: The screen above is for your reference only. Actual values may differ according to model. The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings

Parameter Description

CPU Type This field shows the CPU type and speed of the system. CPU Speed This field shows the speed of the CPU. IDEO Model Name This field shows the model name of IDEO installed on the system. IDEO Serial Number This field displays the serial number of IDEO installed on the

system.

ATAPI Model Name This field shows the model name of the Optical device installed in

the system. System BIOS Version Displays system BIOS version. VGA BIOS Version This field displays the VGA firmware version of the system. Serial Number This field displays the serial number of this unit. Asset Tag Number This field displays the asset tag number of the system. Product Name This field shows product name of the system. Manufacturer Name This field displays the manufacturer of this system. UUID Universally Unique Identifier (UUID) is an identifier standard used in

software construction, standardized by the Open Software

Foundation (OSF) as part of the Distributed Computing Environment

(DCE).

InsydeH20 Setup Utility Rev. 3.5

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

Intel(R) Celeron(R) CPU 900 @ 2.20GHz

2.20GHz ST9320325As

6VE3DDCS Optiarc DVD RW AD-7585H

V1.00 Intel V1800

45DB7C2D-1644-11DF-958C-88AE1D628162

Intel(R) Celeron(R) CPU 900 @ 2.20GHz

2.20GHz ST9320325As

6VE3DDCS Optiarc DVD RW AD-7585H

V1.00 Intel V1800

45DB7C2D-1644-11DF-958C-88AE1D628162

CPU Type: CPU Speed:

IDEO Model Name: IDEO Serial Number: ATAPI Model Name:

System BIOS Version: VGA BIOS Version: Serial Number Asset Tag Number: Product Name: Manufacturer Name: UUID:

CPU Type: CPU Speed:

IDEO Model Name: IDEO Serial Number: ATAPI Model Name:

System BIOS Version: VGA BIOS Version: Serial Number Asset Tag Number: Product Name: Manufacturer Name: UUID:

F5/F6

Main Boot

Exit

SecurityInformation

Chapter 2 29

Main

The Main screen allows the user to set the system time and date as well as enable and disable boot options and recovery .

NOTE: The screen above is for your reference only. Actual values may differ. The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter Description Format/Option

System Time Sets the system time. The hours are displayed with 24-

hour format.

Format: HH:MM:SS (hour:minute:second)

System Date Sets the system date. Format MM/DD/YYYY

(month/day/year)

Total Memory

Displays the total memory available.

N/A

Video Memory

Displays the available memory for Video.

N/A

Quiet Boot The notebook displays an illustration called the OEM

screen during system boot instead of the traditional POST screen that displays the normal diagnostic

messages.

Option: Enabled or Disabled

Network Boot Enables, disables the system boot from LAN (remote

server).

Option: Enabled or Disabled

F12 Boot Menu Enables, disables Boot Menu during POST. Option: Enabled or

Disabled

D2D Recovery Enables, disables D2D Recovery function. The function

allows the user to restore the system to factory defaults.

Option: Enabled or Disabled

SA TA Mode Control the mode in which the SATA controller should

operate.

Option: AHCI Mode or IDE Mode

Item Specific Help

This is the help for the hour field. Valid range is from 0 to 23. INCREASE/REDUCE

: F5/F6.

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

[08:56:55] [02/25/2010]

4095 MB [64 MB]

[Enabled] [Enabled] [Disabled] [Enabled] [AHCI Mode]

[08:56:55]

[02/25/2010] 4095 MB

[64 MB] [Enabled]

[Enabled] [Disabled] [Enabled] [AHCI Mode]

System Time System Date

Total Memory: Video Memory:

Quiet Boot Network Boot F12 Boot Menu D2D Recovery SATA Mode

System Time

System Date Total Memory:

Video Memory: Quiet Boot

Network Boot F12 Boot Menu D2D Recovery SATA Mode

F5/F6

InsydeH20 Setup Utility Rev. 3.5

Boot

Exit

Security

Information

Main

30 Chapter 2

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.

NOTE: System BIOS does not support Trusted Platform Module (TPM).

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings

NOTE: When prompted to enter a password, you have three tries before the system halts. If you forget your

password, you may have to return your notebook computer to your dealer to reset it.

Parameter Description Option

Supervisor Password Is Shows the setting of the supervisor password Clear or Set User Password Is Shows the setting of the user password. Clear or Set HDD Password Is Shows the setting of the HDD password. Clear, Set, or

Frozen

Set Supervisor Password Press Enter to set the supervisor password. When

supervisor password is set, the BIOS Setup Utility is protected from unauthorized access. The user can not either enter the Setup menu nor change the value of parameters except the date and time.

N/A

Set User Password Press Enter to set the user password. When user

password is set, this password protects the BIOS Setup Utility from unauthorized access. The user can enter Setup menu only and does not have right to change the value of parameters.

N/A

Set HDD Password Enter HDD Password. N/A Password on Boot Defines whether a password is required or not in order

for the computer to finish booting up. CAUTION: It may be difficult to reset the computer once the password is lost. Take care when using this function.

Disabled or Enabled

Item Specific Help

Install or Change the password and the length of password must be less than one words.

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

Clear Clear Frozen

[Disabled]

Clear Clear Frozen

[Disabled]

Supervisor Password Is: User Password Is: HDD Password Is:

Set Supervisor Password Set User Password Set HDD Password

Password on Boot

Supervisor Password Is: User Password Is: HDD Password Is:

Set Supervisor Password

Set User Password Set HDD Password

Password on Boot

F5/F6

InsydeH20 Setup Utility Rev. 3.5

Information

Main Boot

Exit

Security

Chapter 2 31

Setting a Password

Follow these steps as you set the user or the supervisor password:

1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears:

2. Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.

3. Press Enter. After setting the password, the computer sets the Supervisor Password parameter to “Set”.

4. If desired, you can opt to enable the Password on Boot parameter.

5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

Removing a Password

Follow these steps:

1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears:

2. Type the curre nt password in the Enter Current Passw ord field and press Enter.

3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.

The computer then sets the Supervisor Password parameter to “Clear”.

4. When you have changed the settings, press F10 to save the changes and exit the BIOS Setup Utility.

Set Supervisor Password

Enter New Password [ ][ ]

Confirm New Password [ ]

Set Supervisor Password

Enter Current Password [ ][ ]

Enter New Password [ ]

Confirm New Password [ ][ ]

32 Chapter 2

Changing a Password

1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears.

2. Type the curre nt password in the Enter Current Passw ord field and press Enter.

3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password

field.

4. Press Enter. After setting the password, the computer sets the Supervisor Password parameter to “Set”.

5. If desired, you can enable the Password on Boot parameter.

6. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

If the verification is OK, the screen will display as following.

The password setting is complete after the user presses Enter. If the current password entered does not match the actual current password, the screen will show you the

Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following message.

Set Supervisor Password

Enter Current Password [ ][ ]

Enter New Password [ ]

Confirm New Password [ ][ ]

Setup Notice

Changes have been saved.

[Continue]

Setup Warning

Invalid Password.

[Continue]Continue

Setup Warning

Passwords do not match.

Re-enter password.

[Continue]Continue

Chapter 2 33

Boot

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.

Select Boot menu to select specific devices to support boot.

Item Specific Help

Use < > or < > to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

Boot priority order:

1. IDEO : Hitachi HTS545032B9A300

2. IDE1 : HL-DT-STDVDRAM GT32N

3. USB FDD :

4. Network Boot : MBA v12.2.0 Slot 0500

5. USB HDD :

6. USB CDROM:

Boot priority order:

1. IDEO : Hitachi HTS545032B9A300

2. IDE1 : HL-DT-STDVDRAM GT32N

3. USB FDD :

4. Network Boot : MBA v12.2.0 Slot 0500

5. USB HDD :

6. USB CDROM:

F5/F6

InsydeH20 Setup Utility Rev. 3.5

Information

Main Boot

Exit

Security

34 Chapter 2

Exit

The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

The table below describes the parameters in this screen.

Parameter Description

Exit Saving Changes Exit System Setup and save your changes. Exit Discarding

Changes

Exit utility without saving setup data.

Load Setup Default Load default values for all setup item. Discard Changes Load previous values for all setup items. Save Changes Save setup data.

Item Specific Help

Exit System Setup and save your changes to CMOS.

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes

Exit Saving Changes

Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes

F5/F6

InsydeH20 Setup Utility Rev. 3.5

Information

Main Boot

Exit

Security

Chapter 2 35

BIOS Flash Utilities

The BIOS flash memory update is required for the following conditions:

• New versions of system programs

• New features or options

• Restore a BIOS when it becomes corrupted.

Use the flash utility to update the system BIOS flash ROM.

NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery

Diskette before you use the flash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the flash. NOTE: Please use the AC adaptor power supply when you run the flash utility. If the battery pack does not

contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not

completely loaded. Follow the steps below to run the flash.

1. Prepare a bootable diskette.

2. Copy the flash utilities to the bootable diskette.

3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.

36 Chapter 2

DOS Flash Utility

Perform the following steps to use the DOS Flash Utility:

1. Press F2 during boot to enter the Setup Menu.

2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move

USB HDD to position 1.

3. Execute the XEWXX100.BAT batch file to update BIOS. The flash process begins as shown.

Item Specific Help

Use < > or < > to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

F1 ESC

Help Exit

Select Item Select Menu

Change Values Select SubMenu

Enter

F9 F10

Setup Default Save and Exit

Boot priority order:

1. IDEO : Hitachi HTS545032B9A300

2. IDE1 : HL-DT-STDVDRAM GT32N

3. USB FDD :

4. Network Boot : MBA v12.2.0 Slot 0500

5. USB HDD :

6. USB CDROM:

Boot priority order:

1. IDEO : Hitachi HTS545032B9A300

2. IDE1 : HL-DT-STDVDRAM GT32N

3. USB FDD :

4. Network Boot : MBA v12.2.0 Slot 0500

5. USB HDD :

6. USB CDROM:

F5/F6

InsydeH20 Setup Utility Rev. 3.5

Information

Main Boot

Exit

Security

Chapter 2 37

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.

38 Chapter 2

WinFlash Utility

Perform the following steps to use the WinFlash Utility:

1. Double-click the WinFlash executable.

2. Click OK to begin the update. A progress screen displays.

Chapter 2 39

Remove HDD/BIOS Password Utilities

This section provides you with details about removing HDD/BIOS password:

Remove HDD Password:

If you key in the wrong HDD password three times, an error is generated.

To reset the HDD password, perform the following steps:

1. After the error is displayed, select the Enter Unlock Password option on the screen.

2. An Encode key is generated for unlocking utilities. Note down this key.

3. Execute the UnlockHD.EXE file to create the unlock code in DOS Mode using the format UnlockHD

[Encode code] with the code noted in the previous step, as follows:

UnlockHD 76943488

4. The command generates a password which can be used for unlocking the HDD.

Password: 46548274

5. Key in the password from the previous step to unlock the HDD as shown.

40 Chapter 2

Removing BIOS Passwords To clear the User or Supervisor passwords, open the DIMM door and use a metal instrument to short the JP9

point.

Cleaning BIOS Passwords

To clean the User or Supervisor passwords, perform the following steps:

1. From a DOS prompt, execute clnpwd.exe

2. Press 1 or 2 to clean the desired password shown on the screen.

The onscreen message determines whether the function is successful or not.

Chapter 2 41

Using Boot Sequence Selector

The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot Sequence Selector, perform the following steps:

1. Enter into DOS.

2. Execute BS.exe to display the usage screen.

3. Select the desired boot sequence by entering the corresponding sequence. For example, enter BS 2 to

change the boot sequence to HDD | CD ROM | LAN | Floppy.

42 Chapter 2

Using DMITools

The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI pool for hardware management.

When the BIOS displays Verifyin g DMI pool data it is checking that the table correlates with the hardware before sending to the operating system (Windows, etc.).

To update the DMI Pool, perform the following steps:

1. Boot into DOS.

2. Execute dmitools. The following messages report to screen to confirm completion:

• dmitools /r ==> Read dmi string from bios

• dmitools /wm xxxx ==> Write manufacturer name to eeprom (max. 16 characters)

• dmitools /wp xxxx ==> Write product name to eeprom (max. 16 characters)

• dmitools /ws xxxx ==> Write serial number to eeprom (max. 22 characters)

• dmitools /wu xxxx ==> Write uuid to eeprom

• dmitools /wa xxxx ==> Write asset tag to eeprom (max. 32 characters)

The following examples show the commands and the corresponding output information.

Read DMI Information from Memory

Input:

dmitools /r

Output:

Manufacturer (Type1, Offset04h): Acer Product Name (Type1, Offset05h): AS5552 Serial Number (Type1, Offset07h): 01234567890123456789 UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx

Write Manufacturer Name to EEPROM

Input:

dmitools /wm Acer

Write Product Name to EEPROM

Input:

dmitools /wp New95

Write Serial Number to EEPROM (Create UUID from Intel WFM20.pdf)

Input:

dmitools /ws 01234567890123456789

Write UUID to EEPROM

Input:

dmitools /wu

Write Asset Tag to EEPROM

Input:

dmitools /wa Acet Asstag

NOTE: When using Write options, restart the system to make the new DMI data effective.

Chapter 3 43

Machine Disassembly and Replacement

IMPORTANT: The outside housing and color may vary from the mass produced model.

This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.

Disassembly Requirements

To disassemble the computer, you need the following tools:

• Wrist grounding strap and conductive mat for preventing electrostatic discharge

• Flat screwdriver

• Philips screwdriver

• Plastic flat screwdriver

• Plastic tweezers

NOTE: The screws for the different components vary in size. During the disassembly process, group the

screws with the corresponding components to avoid mismatch when putting back the components.

Chapter 3

44 Chapter 3

Pre-disassembly Instructions

Before proceeding with the disassembly procedure, make sure that you do the following:

1. Turn off the power to the system and all peripherals.

2. Unplug the AC adapter and all power and signal cables from the system.

3. Place the system on a flat, stable surface.

Chapter 3 45

Disassembly Process

IMPORTANT: The LCD Module cannot be disassembled outside of factory conditions. If any part of the LCD Module is faulty, such as the camera, antenna or LCD panel, the whole module must be replaced.

The disassembly process is divided into the following stages:

• External module disassembly

• Main unit disassembly

• LCD module disassembly

The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you want to remove the mainboard, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

Main Screw List

Screw Quantity Part Number

M2.5*8 19 86.R4F02.002 M2*3 17 86.R4F02.004 M2.5*5 13 86.R4F02.001 M1.98*3 4 86.R4F02.008 M2.5*6 2 86.R4F02.003 M3*3 4 86.R4F02.005

46 Chapter 3

External Module Disassembly Process

IMPORTANT: The outside housing and color may vary from the mass produced model.

External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation of the external module disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the keyboard, you must first remove the switch board.

Screw List

Step Screw Quantity Part No.

ODD Module M 2.5*8 1 86.R4F02.002 ODD Bracket M2*3 2 86.R4F02.004 Lower Logic Door M2.5*8 2 86.R4F02.002 WLAN Module M2*3 1 86.R4F02.004 HDD Carrier M3*3 4 86.R4F02.005

Disconnect power

and signal cables

from system

Remove

Battery

Turn off system and

peripherals power

Remove

DIMMs

Remove

WLAN

Remove

HDD

Remove

ODD

Remove

Lower Logic

Door

Remove

SD Dummy Card

Remove

Keyboard

Remove

RTC Battery

Chapter 3 47

Removing the Battery Pack

1. Turn computer over. Slide the battery lock in the direction shown.

2. Slide and hold the battery release latch to the release position (1), then lift out the battery pack from the main

unit (2).

NOTE: The battery has been highlighted with a yellow oval as shown in the above image. Please detach the

battery and follow local regulations for disposal.

48 Chapter 3

Removing the SD Dummy Card

1. Push the SD dummy card all the way in to eject it.

2. Pull it out from the slot.

Chapter 3 49

Removing the Keyboard

NOTE: The color of the upper cover may vary depending on model.

1. Unlock the six (6) keyboard locks.

2. Pry up the center of the keyboard and rotate it upward away from the upper cover.

3. Turn the keyboard over on to the touchpad area to expose the FPC connector.

50 Chapter 3

4. Open the locking latch and disconnect the FPC from the mainboard.

5. Lift the keyboard clear of the upper cover.

Chapter 3 51

Removing the ODD Module

1. See “Removing the Battery Pack” on page 47.

2. Remove the one (1) screw securing the ODD module.

3. Pull the ODD module out from the chassis.

Step Size Quantity Screw Ty pe

ODD Module M2.5*8 1

52 Chapter 3

4. Remove the two (2) screws securing the ODD bracket and remove the ODD bracket from the ODD module.

5. Remove the ODD bezel by prying the top edge away and clear of the module.

Step Size Quantity Screw Ty pe

ODD Bracket M2*3 2

Chapter 3 53

Removing the Logic Lower Door

1. Remove two (2) screws from the logic lower door.

2. Lift the door beginning from the inner edge as shown.

3. Lift the door clear of the device, exposing the HDD, DIMM, and WLAN modules.

Step Size Quantity Screw Ty pe

Logic Lower Door M2.5*8 2

54 Chapter 3

Removing the DIMM Module

1. See “Removing the Logic Lower Door” on page 53.

2. Push out the release latches on both sides of the DIMM socket to release the DIMM module.

3. Remove the DIMM module.

4. Repeat steps 2 and 3 for the second DIMM module if present.

Chapter 3 55

Removing the WLAN Module

1. See “Removing the Logic Lower Door” on page 53.

2. Disconnect the antenna cables from the WLAN module.

NOTE: Cable placement is Black to the MAIN terminal and White to the AUX terminal.

3. Move the antenna away and remove the one (1) screw to release the WLAN module.

Step Size Quantity Screw Ty pe

WLAN Module M2*3 1

56 Chapter 3

4. Detach the WLAN module from the WLAN socket.

Chapter 3 57

Removing the HDD Module

1. See “Removing the Logic Lower Door” on page 53.

2. Using the pull-tab, slide the HDD module in the direction of the arrow to disconnect the interface.

3. Lift the HDD module clear of the HDD bay.

NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.

58 Chapter 3

4. Remove the four (4) screws (two each side) securing the HDD to the carrier.

5. Remove the HDD from the carrier.

Step Size Quantity Screw Ty pe

HDD Carrier M3*3 4

Chapter 3 59

Removing the RTC Battery

1. See “Removing the WLAN Module” on page 55.

2. Using plastic tweezers, lift the RTC battery from mainboard connector.

60 Chapter 3

Main Unit Disassembly Process

Main Unit Disassembly Flowchart

Screw List

Step Screw Quantity Part No.

Lower Cover M2.5*8 11 86.R4F02.002

M2*3 4 86.R4F02.004 Upper Cover M2.5*5 7 86.R4F02.001 Speaker M2*3 2 86.R4F02.004 Power Board M2*3 1 86.R4F02.004 USB Board M2*3 1 86.R4F02.004 Mainboard M2.5*5 1 86.R4F02.001 Thermal Module M1.98*3 4 86.R4F02.008 LCD Module M2.5*8 4 86.R4F02.002

Remove

Mainboard

Remove

Upper Cover

Remove

Power Board

Remove External

Modules before

proceeding

Remove

Touchpad FFC

Remove

Speaker Module

Remove

CPU

Remove

Thermal Module

Remove

DC-IN Assembly

Remove

LCD Module

Remove

ODD Connector

Board

Remove

Bluetooth Module

Remove

USB Board

Chapter 3 61

Removing the Upper Cover

1. See “External Module Disassembly Process” on page 46.

2. Turn the computer over. Remove the ten (10) screws on the lower cover and four (4) screws from the battery

bay.

Step Size Quantity Screw Ty pe

Lower Cover M2.5*8

(red callout)

M2*3 (green callout)

62 Chapter 3

3. Turn the computer over and disconnect the following three (3) cables from the mainboard.

4. Unlock and disconnect the power board FFC (A).

Chapter 3 63

5. Disconnect the speaker cable (B).

6. Unlock and disconnect the touchpad FFC (C).

NOTE: Avoid pulling on cables directly to prevent damage to the connectors.

64 Chapter 3

7. Remove the eight (8) screws from the upper cover as shown.

8. Starting at the bottom right side of the cover, pry apart the upper and lower covers as shown. Work along the

front edge of the casing to the left as shown, then lift the upper cover clear of the lower cover.

Step Size Quantity Screw Ty pe

Upper Cover M2.5*5 8

Chapter 3 65

Removing the Speaker Module

1. See “Removing the Upper Cove r” on page 61.

2. Locate the speaker module on the upper cover as shown.

3. Remove the speaker module cable from the cable guides.

4. Remove two (2) screws securing the speaker to the upper cove r.

Step Size Quantity Screw Ty pe

Upper Cover M2*3 2

66 Chapter 3

5. Lift the speaker module clear of the device.

Chapter 3 67

Removing the Power Board

NOTE: The power board may vary depending your model.

1. See “Removing the Upper Cove r” on page 61.

2. Locate the power board on the upper cover as shown.

3. Remove one (1) screw from the power board.

4. Turn the upper cover over and remove the power board cable from the upper cover.

Step Size Quantity Screw Type

Power Board M2*3 1

68 Chapter 3

5. Lift the power board from the upper cover and pull the FFC cable through the opening.

Chapter 3 69

Removing the Touchpad FFC

IMPORTANT: The touchpad board cannot be removed individually. To replace the touchpad board, replace the entire upper cover.

1. See “Removing the Upper Cove r” on page 61.

2. Lift the FFC to detach the adhesive securing the cable to the upper cover.

3. Release the FFC locking latch and disconnect the touchpad FFC from the connector.

70 Chapter 3

Removing the USB Board

1. See “Removing the Upper Cove r” on page 61.

2. Unlock the mainboard to USB cable connector.

3. Lift the FFC to detach the adhesive securing the cable to the lower cover.

Chapter 3 71

4. Remove one (1) screw from the USB board.

5. Lift the USB board clear of the lower cover.

Step Size Quantity Screw Ty pe

USB Board M2*3 1

72 Chapter 3

Removing the Bluetooth Module

1. See “Removing the Upper Cove r” on page 61.

2. Pry the Bluetooth board from the adhesive.

3. Disconnect the mainboard to Bluetooth cable.

4. Lift the Bluetooth cable from the cable guides.

Chapter 3 73

Removing the ODD Connector Board

1. See “Removing the Upper Cove r” on page 61.

2. Unlock and disconnect the ODD FFC from the mainboard.

3. Lift the ODD connector board from the lower cover.

74 Chapter 3

Removing the Mainboard

1. See “Removing the Upper Cove r” on page 61.

2. Disconnect the microphone cable from the mainboard.

3. Disconnect the LVDS cable from the mainboard.

4. Remove the LVDS cable and the DC-IN cable from the cable guide.

Chapter 3 75

5. Remove the one (1) securing screw from the mainboard.

6. T o prevent damage, lay the LCD panel flat and cover the panel as shown.

Step Size Quantity Screw Ty pe

Mainboard M2.5*5 1

76 Chapter 3

7. Carefully turn the mainboard over and place it on top of the covered LCD panel. CAUTION: Do not use excessive force when turning the mainboard over as it is still connected to the chassis

by the power cable.

8. Disconnect the power cable.

9. Remove the adhesive tape from the Bluetooth cable.

Chapter 3 77

10. Disconnect the Bluetooth cable from mainboard.

78 Chapter 3

Removing the Thermal Module

1. See “Removing the Upper Cove r” on page 61.

2. Disconnect the fan cable.

3. Remove the four (4) securing screws (in reverse numerical order from screw 4 to 1) from the thermal mo dule.

4. Carefully lift the thermal module clear of the mainboard.

Step Size Quantity Screw Ty pe

Thermal Module M1.98*3 (red

callouts)

Chapter 3 79

Removing the CPU

IMPORTANT: The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may malfunction. Place the CPU on a clean, dry surface when it is not installed.

1. See “Removing the Thermal Module” on page 78.

2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° counter-clockwise as shown.

3. Lift the CPU clear of the socket as shown.

NOTE: Circuit boards >10 cm² have been highlighted with a yellow rectangle as shown in the pr evious

image. Please detach the Circuit board and follow local regulations for disposal.

80 Chapter 3

Removing the LCD Assembly

1. See “Removing the Mainboard” on page 74.

2. Remove the adhesive tape securing the antennas to the lower cover.

3. Free the microphone cable from the cable guides as shown.

4. Free the black and white antenna cables from the cable guides as shown

Chapter 3 81

5. Continue removing the white antenna cable from the cable guides.

6. Continue removing the black antenna cable from the cable guides.

7. Remove four (4) screws from the LCD assembly.

Step Size Quantity Screw Ty pe

LCD Assembly M2.5*8 4

82 Chapter 3

8. Remove the LCD assembly from the lower cover.

Chapter 3 83

Removing the DC-IN Assembly

1. See “Removing the LCD Assembly” on page 80.

2. Lift the DC-IN cable from the lower cover.

3. Lift the DC-IN assembly from the lower cover.

84 Chapter 3

LCD Module Disassembly Process

LCD Module Disassembly Flowchart

Screw List

Step Screw Quantity Part No.

LCD Bezel M2.5*6 2 86.R4F02.003 Inverter Board

(LCD Only)

M2.5*5 1 86.R4F02.001

LCD/LED Panel M2.5*5 4 86.R4F02.001 LCD Brackets M2*3 6 86.R4F02.004

Remove

LCD/LED Panel

Remove

LCD Bezel

Remove

LVDS Cable

Remove LCD

Module from Main

Unit before proceeding

Remove

LCD Brackets

Remove

Antennas

Remove

Camera Module

Remove

Inverter Board

(LCD Only)

Remove

Microphone

Cable

Chapter 3 85

Removing the LCD Bezel

1. See “Removing the LCD Bezel” on page 85.

2. Remove the two bezel screw caps and screws.

3. Starting from the bottom edge of the bezel, pry the bezel upwards and away from the panel. Work along the

side toward the top of the bezel, prying the covers apart. Continue along the top edge and down the other side to remove the bezel.

NOTE: If necessary, use a pry to lift up the outside edges of the bezel.

Step Size Quantity Screw Ty pe

LCD Bezel M2.5*6 2

86 Chapter 3

Removing the Camera Module

1. See “Removing the LCD Bezel” on page 85.

2. Locate the camera module at the top of the LCD module and disconnect the camera cable.

3. Remove the camera from the LCD cover.

Chapter 3 87

Removing the Inverter Board

1. See “Removing the LCD Bezel” on page 85.

2. Remove the adhesive tape securing the inverter board cable to the LCD cover.

3. Remove one (1) screw from the inverter board.

4. Disconnect the inverter board cable going to the LCD panel.

Step Size Quantity Screw Ty pe

Inverter Board M2.5*5 1

88 Chapter 3

5. Disconnect the inverter board cable going to the LVDS cable.

6. Lift the inverter board from the LCD cover.

Chapter 3 89

Removing the LCD/LED Panel

1. See “Removing the LCD Bezel” on page 85.

2. Remove the four (4) securing screws from the LCD/LED panel.

3. Remove the cable from the cable guide.

4. Lift the LCD/LED panel clear of the module.

Step Size Quantity Screw Ty pe

LCD/LED Panel M2.5*5 4

90 Chapter 3

Removing the LCD Brackets

1. See “Removing the LCD/LED Panel” on page 89.

2. Remove the six (6) securing screws (three on each side) from the LCD brackets.

3. Remove the LCD brackets by pulling away from the LCD panel.

Step Size Quantity Screw Ty pe

LCD Brackets M2*3 6

Acer Aspire 5336-2524 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual