Acclaim Lighting Rebel Bar 350 User Manual

OPERATION INSTRUCTIONS

PRODUCT DESCRIPTION

Thank you for your purchasing of Rebel-Bar-350.

As a wall washer, Rebel-Bar-350 features 12 high power RGB LEDs (4Red, 4Green and 4Blue). The
beam angle of lens is available in 10deg, 25deg, 40deg and 10x35deg. Rebel-Bar-350 can be controlled
and set through a LED Setup Tool. Up to 16,000,000 color effects can be created. RGB, C&B and COLOR
modes are for Slave Control. AUTO mode and MANUAL mode are for Master Control.

With scientific fixing design, its adjustable angle lamp holder is excellently steady and easy to
installation. Thanks to the IP65 design, Rebel-Bar-350 is perfect for indoor and outdoor applications. The
fantastic lighting effect makes Rebel-Bar-350 ideal for architectural wash applications and suitable for
high impact scene settings.

TECHNICAL SPECIFICATION

)tib42(noillim7.61egnaRroloC

Source Life
LED Type

Light Source

Input Voltage

Power Requirement

Power Consumption

Beam Angle

Listing

Control
IP Rating

Connection
Housing

Operating Temperature

Storage Temperature

Dimension
Weight

50,000 hours under normal operating conditions

Rebel LED
12pcs high power Rebel LEDs (4Red, 4Green and 4 Blue)

AC100-240V, 50/60Hz

24VDC
30W Max.

ooo o

10 /25 /40 /10x35 (oval)

CE certified
DMX 512 protocol

IP 65
8-pin IP67 waterproof connector

Anodized aluminum extrusion

o o

0 C ~ +40 C

o o

-20 C ~ +70 C
350(L) x 85(W) x 75(H)mm

1.1Kgs

*NOTICE:

All rights reserved! Specifications and improvement in the design of the unit and this manual are subject to change
without prior notice.

-1-

OPERATION GUIDE(PROGRAMMING)

A LED Setup Tool (depicted here) _XB-R1 is required to program
the Rebel-Bar-350. For further information, please refer to its
accompanying manual.

1. Slave Control

In Slave control, Address setting ( ) and Glide effect function can be

001~512

set through a LED Setup Tool(sold separately). In RGB, C&B and COLOR

A LED Setup Tool(XB-R1)

(Sold separately)

mode, relevant controls are as below:

(1)In RGB mode:

Red color effect is controlled by Channel 1.
Green color effect is controlled by Channel 2.
Blue color effect is controlled by Channel 3.

(2)In C&B mode:

Color effect is controlled by Channel 1.
Brightness is controlled by Channel 2.

(3)In COLOR mode:

Color effect is controlled by Channel 1.
Brightness(lighting intensity) is always in 100% level.

NOTE:

1. The Glide Effect function can be switched on(YES) or off(NO). The transition from one level to another is
smoother when this function is switched on.

2. When this function is switched off, the lighting intensity will change from one level to another abruptly. (Thus,
when a quick lighting effect is required, the Glide Effect function should be switched off.)

3. If the DMX signal is interrupted, the driver will keep the last received DMX signal(information) until the driver is
switched off or a new and valid DMX signal is sent.

2.Master Control

AUTO mode and MANUAL mode are for Master Control. Relevant functions are as below:

(1) AUTO mode:

Preset programs:1-10 programs and "AUTO" program ( program is the sequential running of these

"AUTO"

1-10 programs.)

Auto Speed: 1~100. Auto Fadetime: 0%~100%.

(2) MANUAL mode:

BLUE/Duration: 0%~100%. RED/Speed: .0%~100% GREEN/Dimmer: .0%~100%

NOTE:

1. The LEDs will turn red in Slave Control mode.
The LEDs will give responding sensitive when the parameters are adjusted in Master Control.

2. If the LED is not selected in "Setup with answer", it will turn red.
If the LED is not selected in "Setup no answer", it will switch off.

When the user confirms the settings of the LED products, the LEDs will flash momentarily to confirm that the
settings have been saved.

-2-