Pixel Driver MiniPixelDriverMini
Descriptions:
Congratulations with your purchase of this product.
The Pixel Driver Mini is intended to design for our product PS-5/PS-10. As a LED driver, the
features DMX addresses are assigned automatically and the value of controlling pixel is selectable. The Red,
Green and Blue of each pixel can be controlled separately as well.
Delivery Packet:
Check for transport damage.
You should be in possession of the following items:
Pixel Driver Mini
1
1 Manual
1 First Cable
1 Screw Driver
1 Connecting Part
Should you discover transport damage after unpacking the equipment, inform the hauler immediately. Never
connect a damaged device. You may also contact your supplier.
Main Features:
Pixel Driver Mini
LED driver idea design for color mixing (PS-5/PS-10).
Compatible for DMX-512(1990) and DMX-1000K(1M).
-170 pixels can be linked up via DMX-512
-600 pixels can be linked up via DMX-1000K(1M)
Automatically DMX addressing.
LED Display.
The value of controlling pixel is selectable(5~200).
Technical Specifications:
Operation Voltage
Connection
Housing
Ingress Protection Rating
Control Protocol
Listing
Operation temperature
Dimensions
Weights
*Please Note: Improvements and specifications in the design of the unit and the manual are subject to change
without any prior written notice.
*Special Note: For reducing signal errors and avoiding signal transmission problems and interference,it is always
advisable to connect 120 ohm impedance DMX signal cable and DMX terminal for signal connection.
DC 5V
DMX In via 3-pin Terminal
DMX Out via 3-pin Terminal
Power In via 2-pin Terminal
Output via 6-pin Terminal
PC +UV resistance
Indoor Use Only
Compatible DMX-512 (1990) and DMX-1000K(1M)
CE certified
-10 degC to +50 degC
90(L) x 43(W) x 20(H)mm
35g
-Page 1-
Operation Guide:
DMX In
DMX Out
Power Input
GND
Data -
Data+
GND
Data -
Data+
GND
+5V
DMX IN
Pixel Driver Mini
DMX OUT
DC IN
5A Max.
Made inPRC
Up
DMX
Down
1
2
3
4
OUTPUT
5
6
DMX/Power Output
(Via 6-Pin terminal)
1.The below table details the assignment of the 6-pin terminal.
1
2
3
4
OUTPUT
5
6
Pin 1=GND
Pin 2=SIN
Pin 3=DCLK
6-Pin Terminal Configuration
Pin 4=LE
Pin 5=GCLK
Pin 6=+5V
2. DMX & Power supply Setup
Pixel Driver Mini is compatible for DMX-512 protocol or DMX-1000K(1M).Connect DMX-512 or DMX-1000K
Signal to DMX input port of the first Pixel Driver Mini,connect DMX output port of the first Pixel Driver Mini to
DMX input port of the second Pixel Driver Mini. The rest may be deduced by analogy. A maximum of 170
pixels can be linked up via DMX-512 and 600 pixels can be linked up via DMX-1000K(1M).
3. And Pixel Driver Mini is auto-addressing, DMX address and channels will increase automatically in the
sequence. The first pixel of the first Pixel Driver Mini output port serves as DMX Address 1.
4.Use the UP button to increase the controllable pixel value of the PS-5/PS-10. Press it once, the value
will increase 5, hold it down, the value will increase to the maximum soon. The DOWN button is used to
decrease the controllable pixel value of the PS-5/PS-10. Press it once, the value will decrease 5, hold
it down, the value will decrease to the minimum soon.
5.The LED indicator will be blacked out without operation in 5 minutes, press any key to resume display.
NOTE:
The total current of connection Pixel Driver Mini(s) and PS-5/PS-10 NEVER exceed the power supply current
capacity.
24-004-2676-00
Rev 1.0
-Page 2-
Loading...