Access sp2603 Installation Manual

Introduction

IMPORTANT:

The 2603 is an Accessory Handset for use with the 2652 system. You must have
the 2652 in order to use the 2603 Accessory Handset.

This manual is designed to familiarize you with the 2603 Accessory Handset setup,
registration and basic functions. For detailed operational instructions, please refer to
the 2652 manual.

1

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink,

or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage.

6. Slots and openings in the Handset and Base Unit are provided for ventilation. To

protect it from overheating, these openings must not be blocked by placing the
product on the bed, sofa, rug, or other similar surface. This product should never
be placed near or over a radiator or heat register. This product should not be placed
in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where

the cord might be damaged by anyone walking on it.

9. Never push objects of any kind into this product through Handset or Base Unit slots

as they may touch dangerous voltage points or short out parts that could result
in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product, but take it

to an authorized service facility. Opening or removing cabinet parts other than
specified access doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the appliance is subsequently
used.

11. Do not overload wall outlets and extension cords as this can result in the risk of

fire or electric shock.

2

Important Safety Instructions

12.Unplug this product from the wall outlet and refer servicing to an authorized service

facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions,
because improper adjustment of other controls may result in damage and will
often require extensive work by an authorized technician to restore the product

to normal operation.
E. If the product has been dropped and the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than a cordless type) during an electrical storm. There

may be a remote risk of electric shock from lightning.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

3

Getting Started

Your 2652 multi-handset system can operate up to 4 Handsets.
The accessory Handset 2603 consists of the following:

AC Power Adaptor

Setup of the 2603 Accessory
Handset

1. Plug the AC power adapter into an

1

3

5

electrical outlet. Plug the DC connector
into the bottom of the Charger Unit.

2. Remove the Handset battery

compartment cover by pressing on
the indent and sliding downward.

3. Place the new battery pack in the

Handset, with the metal contacts
aligned with the charge contacts in
the battery compartment.

4. Replace the battery compartment

cover by sliding it upward.

5. Place the Handset in the Charge

Cradle, and allow it to charge for 12
hours. After the initial charge, a
maintenance charge of 12 hours should
be sufficient.

Setup

4

Registration

Enter ID Code

1. After charging the Handset, remove

it from its Charge Cradle, the screen
will display:

2. Press NEW, then enter the 15 digit

Base ID code, located on the
underside of the 2652 Base Unit.

3. Press OK. The Handset will display:

PLEASE WAIT!!

4. Wait approximately 15 seconds. The

Handset will display:

FOUND BASE
NOTE: Occasionally, it will take

longer than 15 seconds for the
Handset to find the Base Unit. This
is normal.

If the Handset displays: SYSTEM IS
BUSY PLEASE TRY LATER, this
indicates that the system is in use.
Wait until the Base Unit is in the idle
(on hook) mode, and repeat steps
2 through 4.

Congratulations! You can now enjoy the
benefits of your multi-Handset system.

NO BASE

SUBSCRIPTION

5

The Handset Layout

1

2

3

9

4
5

6

7

8

1. Antenna

2. Message Waiting Indicator

3. Earpiece

4. Headset Jack (2.5mm)

5. Scroll Keys

6. On (Flash)

7. Dialing Key (0-9, , #)

10

11

12
13

14

8. Handsfree
Speakerphone

9. LCD Display

10. Select

11. Off (Clear)

12. Billed Services

13. Intercom

14. Microphone

6