Abit FATAL1TY-AA8XE User Manual
Intel Pentium 4 System Board
Socket 775
User’s Manual
For more information:
www.abit.com.tw
4200-0433-01
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
The Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are trademarks of
Fatal1ty, Inc. All rights reserved. Built to Kill is a trademark of PWX, LLC.
© 2004 ABIT Computer Corporation.
All other trademarks are the property of their respective owners.
Fatal1ty AA8XE
Table of Contents
Chapter 1. Introduction .......................................................................... 1-1
1-1. Fatal1ty.....................................................................................................1-1
1-2. Features & Specifications ........................................................................1-3
1-3. Layout Diagram .......................................................................................1-5
Chapter 2. Hardware Setup.................................................................... 2-1
2-1. Install The Motherboard...........................................................................2-1
2-2. Install CPU, Heatsink and Fan Assembly................................................2-3
2-3. Install System Memory ............................................................................2-5
2-4. Connectors, Headers and Switches ..........................................................2-7
(1). ATX Power Input Connectors........................................................2-7
(2). FAN Power Connectors .................................................................2-8
(3). CMOS Memory Clearing Header ..................................................2-9
(4). Wake-up Header...........................................................................2-10
(5). Front Panel Audio Connection Header ........................................ 2-11
(6). Back Panel Audio Connection Slot..............................................2-12
(7). Front Panel COM1 Connection Header.......................................2-14
(8). Front Panel Switches & Indicators Headers ................................2-15
(9). Additional IEEE1394 Port Headers .............................................2-16
(10). Additional USB Port Headers......................................................2-17
(11). GURU Clock Connection Header................................................2-18
(12). Internal Audio Connectors ...........................................................2-18
(13). Floppy and IDE Disk Drive Connectors......................................2-19
(14). POST Code Display .....................................................................2-20
(15). Serial ATA Connectors .................................................................2-21
(16). PCI Express x16 Slot ...................................................................2-22
(17). PCI Express x1 Slots....................................................................2-22
(18). Onboard Switches........................................................................2-23
(19). Status Indicator ............................................................................2-24
(20). Back Panel Connectors ................................................................2-25
Chapter 3. BIOS Setup............................................................................ 3-1
3-1. µGuru™ Utility .........................................................................................3-2
3-2. Standard CMOS Features.........................................................................3-9
3-3. Advanced BIOS Features....................................................................... 3-12
3-4. Advanced Chipset Features....................................................................3-15
3-5. Integrated Peripherals ............................................................................3-17
3-6. Power Management Setup .....................................................................3-22
User’s Manual
3-7. PnP/PCI Configurations.........................................................................3-25
3-8. Load Fail-Safe Defaults .........................................................................3-26
3-9. Load Optimized Defaults .......................................................................3-26
3-10. Set Password .......................................................................................... 3-26
3-11. Save & Exit Setup..................................................................................3-26
3-12. Exit Without Saving...............................................................................3-26
Appendix A. Install Intel Chipset Software Utility...............................................A-1
Appendix B. Install Intel Application Accelerator RAID.................................... B-1
Appendix C. Install Audio Driver......................................................................... C-1
Appendix D. Install LAN Driver ...........................................................................D-1
Appendix E. Install USB 2.0 Driver ..................................................................... E-1
Appendix F. Install ABIT µGuru Utility.............................................................. F-1
Appendix G. POST Code Definition .....................................................................G-1
Appendix H. Troubleshooting (Need Assistance?)...............................................H-1
Appendix I. How to Get Technical Support ......................................................... I-1
For more information:
www.abit.com.tw
Fatal1ty AA8XE
Introduction 1-1
Chapter 1. Introduction
1-1. Fatal1ty
FATAL1TY STORY
Who knew that at age 19, I would be a
World Champion PC gamer. When I was
13, I actually played competitive billiards in
professional tournaments and won four or
five games off guys who played at the
highest level. I actually thought of making
a career of it, but at that young age
situations change rapidly. Because I’ve
been blessed with great hand-eye
coordination and a grasp of mathematics (an
important element in video gaming) I
gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional
League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one
of the top players in the United States, a company interested in sponsoring me flew me to
Sweden to compete against the top 12 players in the world. I won 18 straight games, lost
none, and took first place, becoming the number one ranked Quake III player in the world in
the process. Two months later I followed that success by traveling to Dallas and defending
my title as the world’s best Quake III player, winning the $40,000 grand prize. My earned
frags allowed at this tournament were 2.5. From there I entered competitions all over the
world, including Singapore, Korea, Germany, Australia, Holland and Brazil in addition to Los
Angeles, New York and St. Louis.
WINNING STREAK
I was excited to showcase my true gaming skills when defending my title as CPL Champion
of the year at the CPL Winter 2001 because I would be competing in a totally different first
person shooter (fps) game, Alien vs. Predator II. I won that competition and walked away
with a new car. The next year I won the same title playing Unreal Tournament 2003,
becoming the only three-time CPL champion. And I did it playing a different game each
year, something no one else has ever done and a feat of which I am extremely proud.
At QuakeCon 2002, I faced off against my rival ZeRo4 in one of the most highly anticipated
matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon 2004, I
became the World’s 1
matches and earning $25,000 for the victory.
st
Doom3 Champion by defeating Daler in a series of very challenging
User’s Manual
1-2 Chapter 1
LIVIN’ LARGE
Since my first big tournament wins, I have been a “Professional Cyberathlete”, traveling the
world and livin’ large with lots of International media coverage on outlets such as MTV,
ESPN and G4TV to name only a few. It's unreal - it's crazy. I’m living a dream by playing
video games for a living. I’ve always been athletic and took sports like hockey and football
very seriously, working out and training hard. This discipline helps me become a better
gamer and my drive to be the best has opened the doors necessary to become a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made up of
the best parts under my own brand. Quality hardware makes a huge difference in
competitions…a couple more frames per second and everything gets really nice. It's all
about getting the computer processing faster and allowing more fluid movement around the
maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying
about their equipment, something I’ve preached since I began competing. I don’t want to
worry about my equipment. I want it to be there – over and done with - so I can focus on the
game. I want it to be the fastest and most stable computer equipment on the face of the
planet, so quality is what Fatal1ty brand products will represent.
FATAL1TY BRAIN TRUST
This is just the beginning. We’re already in development for several new products, including
high-level Fatal1ty – PWX systems for next year, and I’m really grateful to all my Fatal1ty
Brain Trust partners for helping make my dreams a reality.
I know there is a business side to all of this, but for me the true reward is making products
that are so good I can win with them – and making them available to fellow gamers.
Gaming is my life, and many fellow gamers around the world are also some of my best
friends, so giving back to the gaming community is really important to me.
Johnathan “Fatal1ty” Wendel
Fatal1ty AA8XE
Introduction 1-3
1-2. Features & Specifications
1. CPU
• Designed for Intel® 90nm Pentium 4 LGA775 processors with 1066/800 MHz FSB
• Supports Intel
2. Chipset
• Intel® 925XE / Intel® ICH6R Express Chipset
3. Memory
• Four 240-pin DIMM slots
• Supports Dual channel DDR2-533/400 non-ECC un-buffered memory
• Supports maximum memory capacity up to 4GB
4. ABIT Engineered
• ABIT uGuru™ Technology (ABIT OC Guru/ABIT EQ/ABIT Flash Menu/ABIT Black Box)
• ABIT ThermalGuard
• ABIT TweakGuard
• ABIT OTES
• ABIT OC strip Technology
• ABIT PWM cooling Technology
• ABIT Aero OTES Technology
• ABIT Audio Purification Technology for Dolby Digital Live
• ABIT MB LED back-light
• ABIT MB color management system for easy installation
• ABIT Guru peripheral product link
- Guru Clock: Refer to Guru Clock SPEC
- Guru Game Panel: CMOS Reset Button/USB 2.0/1394/SATA/Audio IO/Large LCD at
front side
5. SATA RAID
• Intel® Matrix Storage Technology supports 4 ports SATA 150 RAID 0/1
6. Dual LAN
• Intel® Gigabit LAN
®
• Intel
7. IEEE 1394
• Supports 3 Ports IEEE 1394 at 100/200/400 Mb/s transfer rate
8. Audio
• 7.1 channels Intel HD Audio with Dolby Digital Live
• Supports auto jack sensing and optical S/PDIF In/Out
®
Hyper-Threading Technology
™
Technology
™
Technology
™
cooling Technology (Enhanced Version)
10/100Mbps LAN
User’s Manual
1-4 Chapter 1
9. Internal I/O Connectors
• 1x PCI-E X16 slot
• 2x PCI-E X1 slots
• 2x PCI slots
• 1x Audio daughter card port
• 1x Floppy port
• 1x UDMA 100/66/33 connector
• 4x SATA 150 connectors
• 2x USB 2.0 headers
• 2x IEEE1394 headers
10. Back Panel I/O
• ABIT Dual OTES™
• 1x PS/2 keyboard, 1 x PS/2 mouse
• 1x IEEE1394
• 4x USB 2.0
• 1x RJ-45 LAN (Gigabit), 1 x RJ-45 LAN (10/100)
11. Miscellaneous
• ATX form factor (305mm x 245mm)
Specifications and information contained herein are subject to change without notice.
For more information:
www.abit.com.tw
Fatal1ty AA8XE
Introduction 1-5
1-3. Layout Diagram
User’s Manual
1-6 Chapter 1
For more information:
www.abit.com.tw
Fatal1ty AA8XE
Hardware Setup 2-1
Chapter 2. Hardware Setup
Before installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or become damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow the motherboard to be securely
attached, and at the same time, prevent the system from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use studs, or
2. use spacers
In principle, the best way to attach the board is to
use studs. Only if you are unable to do this should
you attach the board with spacers. Line up the
holes on the board with the mounting holes on the
chassis. If the holes line up and there are screw
holes, you can attach the board with studs. If the
holes line up and there are only slots, you can
only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has
been positioned, check to make sure everything is
OK before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
2-2 Chapter 2
Before installing this motherboard, exam your chassis to ensure this motherboard fits into it.
1. Face the side of the I/O ports toward the rear part of the chassis.
2. Locate the screw holes on the motherboard and the chassis base.
3. Place all the studs or spacers needed on the chassis base, and then have them tightened.
4. Line up all the screw holes on the motherboard with those studs or spacers on the chassis.
5. Tighten all the screws.
As the Dual OTES Fan Duct takes up two screw-hole positions that are traditionally used for motherboard
installation, please refer to the “ABIT Dual OTES” quick installation guide for details.
Fatal1ty AA8XE
Hardware Setup 2-3
2-2. Install CPU, Heatsink and Fan Assembly
In order to protect the contact pins, please pay
attention to these notices:
1. A maximum 20 cycles of CPU installation
is recommended.
2. Never touch the contact pins with fingers
or any object.
3. Always put on the cap when the CPU is
not in use.
4. Use your right thumb and forefinger to
grasp the CPU package. Be sure to grasp on the
edge of the substrate, and face the Pin-1
indicator toward the bottom-left side. Aim at the
socket and place the CPU package vertical
down into the socket.
1. Place the board so as to let the lever hook
of the socket is on your left side. Use your left
thumb and forefinger to hold the lever hook,
pull it away from the retention tab.
2. Rotate the lever to fully open position.
3. Use your right thumb on the bottom-right
side of the load plate and lift it up to fully open
position.
5. Visually inspect if the CPU is seated well
into the socket. The alignment key must be
located in the notch of package.
6. Use your left hand to hold the load plate,
and use your right thumb to peel the cap off.
User’s Manual
2-4 Chapter 2
The cap plays an important role in protecting
contact pins. In order to prevent bent pin, PUT
ON the cap after operation or testing.
7. Lower the plate onto the CPU package.
Engage the load lever while gently pressing
down the load plate.
8. Secure the lever with the hook under
retention tab.
For detailed information on how to install your
heatsink and fan assembly, please refer to the
instruction manual came packed with the
heatsink and fan assembly you bought.
10. Press each of the four fasteners down into
the mounting holes.
11. Rotate the fastener clock-wise to lock the
heatsink and fan assembly into position.
9. Place the heatsink and fan assembly onto
the socket. Align the four fasteners toward the
four mounting holes on the motherboard.
Fatal1ty AA8XE
12. Attach the four-pin power plug from the
heatsink and fan assembly to the CPU FAN
connector.
Hardware Setup 2-5
2-3. Install System Memory
The Intel 925XE Express Chipset MCH memory interface is designed with Flex Memory Technology
supporting single-channel or dual-channel DDR2 memory configurations.
• To reach the optimum performance in dual-channel configurations, install identical DDR2 DIMM
pairs for each channel.
• Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain memory
modules from the same vendor.
• Due to chipset resource allocation, the system may detect less than 4GB of system memory in the
installation of four 1GB DDR2 memory modules.
• Due to chipset limitation, 128MB DIMM modules or double-sided x16 memory chips are not
supported.
There are several methods of different DDR2 configurations depending on how the DIMMs are populated
on each system memory channel:
• [Single Channel]: only one channel is populated.
Method
1 512MB - - 2 - 512MB - 3 - - 512MB 4 - - - 512MB
5 512MB 512MB - 6 - - 512MB 512MB
DIMM1 DIMM2 DIMM3 DIMM4
Channel A Channel B
User’s Manual
2-6 Chapter 2
• [Dual Channel Asymmetric]: both channels are populated, but each channel has a different
amount of total memory. (Channel A≠Channel B)
Method
DIMM1 DIMM2 DIMM3 DIMM4
Channel A Channel B
1 512MB - 256MB 2 - 256MB - 512MB
3 512MB - - 256MB
4 - 256MB 512MB 5 256MB 256MB 256MB 6 256MB 256MB - 256MB
7 256MB - 256MB 256MB
8 - 256MB 256MB 256MB
9 256MB 256MB 512MB 512MB
10 256MB 256MB 256MB 512MB
• [Dual Channel Symmetric]: both channels are populated where each channel has the same amount
of total memory. (Channel A＝Channel B)
Method
DIMM1 DIMM2 DIMM3 DIMM4
Channel A Channel B
1 512MB - 512MB 2 - 512MB - 512MB
3 512MB - - 512MB
4 - 512MB 512MB 5 256MB 256MB 512MB 6 256MB 256MB - 512MB
7 512MB - 256MB 256MB
8 - 512MB 256MB 256MB
9 512MB 256MB 512MB 256MB
10 256MB 512MB 256MB 512MB
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1. Locate the DIMM slot on the board.
2. Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3. Align the notch key on the module with the
rib on the slot.
4. Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch. Do not force the DIMM module in with extra force as
the DIMM module only fit in one direction.
5. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
Fatal1ty AA8XE
Hardware Setup 2-7
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
ATX Power Input Connectors
(1).
This motherboard provides two power connectors to connect ATX12V power supplier.
NOTE: This 24-pin power connector “ATXPWR1” is compliant to the former 20-pin type. Pay attention
to the orientation when doing so (Pin-11, 12, 23, and 24 should be left un-connected).
User’s Manual
2-8 Chapter 2
(2). FAN Power Connectors
These connectors each provide power to the cooling fans installed in your system.
• CPUFAN1: CPU Fan Power Connector
• NBFAN1: Chipset Fan Power Connector
• SYSFAN1: System Fan Power Connector
• OTESFAN1, OTESFAN2: OTES Fan Power Connector
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
Fatal1ty AA8XE
Hardware Setup 2-9
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
• Pin 1-2 shorted (default): Normal operation.
• Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
User’s Manual
2-10 Chapter 2
(4). Wake-up Header
These headers use a jumper cap to enable/disable the wake-up function.
• USB-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at USB1 port.
Pin 2-3 shorted: Enable wake-up function support at USB1 port.
• USB-PWR2:
Pin 1-2 shorted (default): Disable wake-up function support at USB2 port.
Pin 2-3 shorted: Enable wake-up function support at USB2 port
Fatal1ty AA8XE
Hardware Setup 2-11
(5). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
Pin Pin Assignment Pin Pin Assignment
1 MIC2 L (Microphone 2 Left) 2 AGND (Analog Ground)
3 MIC2 R (Microphone 2 Right) 4 AVCC (Analog VCC Power)
5 FRO-R (Front Right) 6
7 F_IO_SEN (Front I/O Sensor)
9 FRO-L (Front Left) 10
MIC2_JD (Microphone 2 Jack
Detect)
LINE2_JD (Line 2 Jack
Detect)
User’s Manual
2-12 Chapter 2
(6). Back Panel Audio Connection Slot
The slot “BP-AUDIO1” provides the audio input/output connection at back panel through an audio
daughter-card.
NOTE: Install this daughter-card at slot “BP-AUDIO1”.
S/PDIF Out: This connector provides an S/PDIF-Out connection through optical fiber to digital
•
multimedia devices.
•
S/PDIF In: This connector provides an S/PDIF-In connection through optical fiber to digital
multimedia devices.
Line-In: Connects to the line out from external audio sources.
• Mic-In: Connects to the plug from external microphone.
• Line-Out: Connects to the front left and front right channel in the 7.1-channel or regular
2-channel audio system.
Center/Subwoofer: Connects to the center and subwoofer channel in the 7.1 channel audio
•
system.
R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 7.1
•
channel audio system.
•
S.L./S.R. (Surround Left / Surround Right): Connects to the surround left and surround
right channel in the 7.1 channel audio system.
Fatal1ty AA8XE
Hardware Setup 2-13
S/PDIF Connection:
Along with the motherboard package you can find an audio daughter-card and a roll of optical
fiber cable for S/PDIF connection.
• S/PDIF Input Connection:
1. Plug the end with 3.5mm adapter into the [JK1] jack on this daughter-card. (This jack is used
for either optical or line input.)
2. Remove the rubber protection-cap at the other end. Plug it into the [Digital-Out] (SPDIF-Out)
jack on your digital multimedia device.
• S/PDIF Output Connection:
1. Pull out the 3.5mm adapter at one end. Keep this adapter with its protection-cap covered in
save place. Plug the rest of this end into the [SPDIF-O] jack on this daughter-card.
2. Remove the rubber protection-cap at the other end. Plug it into the [Digital-In] (SPDIF-In) jack
on your digital multimedia device.
User’s Manual
2-14 Chapter 2
(7). Front Panel COM1 Connection Header
This header provides one additional COM1 port connection through an extension cable and bracket.
Pin Pin Assignment Pin Pin Assignment
1 DCD (Data Carrier Detect) 2 RXD (Receive-Data)
3 TXD (Transfer-Data) 4 DTR (Data-Terminal-Ready)
5 GND 6 DSR (Data-Set-Ready)
7 RTS (Request-to-Send) 8 CTS (Clear-to-Send)
9 RI (Ring-Indicator) 10 NC (No Connected)
Fatal1ty AA8XE
Hardware Setup 2-15
(8). Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
• HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
• RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
• SPKR (Pin 13, 15, 17, 19):
Connects to the System Speaker cable of chassis.
• SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
• PWR (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
• PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
User’s Manual
2-16 Chapter 2
(9). Additional IEEE1394 Port Headers
These headers each provide one additional IEEE1394 port connection through an extension cable and
bracket.
Pin Pin Assignment Pin Pin Assignment
1 TPA0 + 2 TPA0 -
3 Ground 4 Ground
5 TPB0 + 6 TPB0 -
7 +12V 8 +12V
9 NC 10 Ground
Fatal1ty AA8XE
Hardware Setup 2-17
(10). Additional USB Port Headers
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for
USB 2.0 specifications.
Pin Pin Assignment Pin Pin Assignment
1 VCC 2 VCC
3 Data0 - 4 Data1 -
5 Data0 + 6 Data1 +
7 Ground 8 Ground
9 NC 10 NC
User’s Manual
Loading...