Ethernet Module PER-C33L
PER-C33L
®
Intel
82574
Four PCI-Express 10/100/1000
Ethernet Module
PER-C33L Manual Rev.A 1st Ed.
September 2008
Ethernet Module PER-C33L
Copyright Notice
This document is copyrighted, 2008. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
Ethernet Module PER-C33L
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 PER-C33L Ethernet Module
• 1 CD-ROM for manual (in PDF format) and drivers
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.
ii
Ethernet Module PER-C33L
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features....................................................................1-3
1.3 Specifications............................................................ 1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions.................................................... 2-2
2.2 Location of Connectors and Jumpers .......................2-3
2.3 Mechanical Drawing..................................................2-5
2.4 LAN Module Installation ............................................2-7
Chapter 3 Driver Installation
3.1 Installation.................................................................3-2
iii
Ethernet Module PER-C33L
Chapter
1
General
Information
Chapter 1 General Information 1 - 1
Ethernet Module PER-C33L
1.1 Introduction
The PER-C33L comes with four PCI-Express 10/100/1000Base-TX
Ethernet Module that is suitable for high performance network
appliances. This Ethernet module extends the PCI-Express
interfaces and provides higher speed and performance of
communications in any compatible AAEON products.
The PER-C33L features four copper LAN ports that support
10/100/1000 Base-TX network speed to fulfill the demands of
flexible network expansion. Moreover, the PER-C33L
accommodates four PCI-Express ［x1］or optional PCI-Express
［x4］if you require a different expansion interface. PER-C33L wi ll
be a great solution to keep an existing system a better extension.
Chapter 1 General Information 1 - 2
Ethernet Module PER-C33L
1.2 Features
Four PCI-Express Host Interface
Four 10/100/1000Base-TX Cooper Ethernet Ports
Supports Two-Port Bypass Function
Chapter 1 General Information 1 - 3
Ethernet Module PER-C33L
1.3 Specifications
System
Chipset: Intel
Expansion Interface: PCI-Express［x1］x 4 or
Power Supply Request: From PCI-Express connector
Operating Temperature: 32°F~140°F (0°C~60°C)
Dimension: 5.4” x 3.5” (137.8mm x 88mm)
EMC: CE/FCC Class A
®
PCI-Express
10/100/1000Mb LANs, RJ-45
connector x 4, 2-port bypass
function (LAN2 & LAN3)
PCI-Express［x4］x 1 (PLX 8508
optional)
Chapter 1 General Information 1 - 4
Ethernet Module PER-C33L
Chapter
2
Quick
Installation
Guide
Chapter 2 Quick Installation Guide 2-1
Ethernet Module PER-C33L
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis
Chapter 2 Quick Installation Guide 2-2
Ethernet Module PER-C33L
2.2 Location of Connectors and Jumpers
Component Side
Chapter 2 Quick Installation Guide 2-3
Ethernet Module PER-C33L
Solder Side
Chapter 2 Quick Installation Guide 2-4
Ethernet Module PER-C33L
2.3 Mechanical Drawing
Component Side
Chapter 2 Quick Installation Guide 2-5
Ethernet Module PER-C33L
Solder Side
Chapter 2 Quick Installation Guide 2-6
Ethernet Module PER-C33L
2.4 LAN Module Installation
Step1: Loosen the screws in the back of chassis
Step 2: Remove the null Module cover or LAN module
Chapter 2 Quick Installation Guide 2-7
Ethernet Module PER-C33L
Step 3: Insert the LAN Module and fasten the screw
Chapter 2 Quick Installation Guide 2-8
Ethernet Module PER-C33L
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Main Board/ Daughter Board/ Backplane
有毒有害物质或元素
部件名称
印刷电路板
及其电子组件
外部信号
连接器及线材
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。
铅
(Pb)汞 (Hg)镉 (Cd)
× ○ ○ ○ ○ ○
× ○ ○ ○ ○ ○
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
Chapter 2 Quick Installation Guide 2-9
Ethernet Module PER-C33L
Chapter
3
Driver
Installation
Chapter 3 Driver Installation 3-1
Ethernet Module PER-C33L
3.1 Installation:
Insert the PER-C33L CD-ROM into the CD-ROM Drive. And follow
the instructions to install the driver. you can activate the installation
items through Autorun program which will install each driver
directly.
1. Click on the LAN folder and select the OS your system is
2. Doub
le click on the .exe file locates in each OS folder
3. Follow the instructions that the window shows
4. The sy
stem will help you install the driver automatically
If your system do not support Autorun program or you cannot install
drivers successfully, please read instructions below for further
detailed installations.
1. Go to My Computer and click on the right of mouse,
select Properties
2.
Select Hardware
3. Enter Device Managemen
4. Select your LAN card and clic
5. Select Update your driver and follow the instructions
t
k on the right of mouse
that the window show
6. Selec
7. Click on the PER-C33L (depends
t to install from CD-ROM
on the chip your card
supports) folder
8. ur system is
Choose the OS yo
9. The system will help you install the driv
10. Please re-start your computer
Chapter 3 Driver Installation 3-2
er automatically
Loading...