Page 1
EPIC Board EPIC-9457 Rev.B
EPIC-9457 Rev.B
Intel® Atom™ N270 Processor
Onboard DDR II Memory
Up to 24-bit Dual-channel LVDS LCD
6 USB 2.0 / 4 COMs / 2 SATA
CompactFlash™/ 8-bit Digital I/O
EPIC-9457 Manual Rev.B 3rd Ed.
April 2010
Page 2
EPIC Board EPIC-9457 Rev.B
Copyright Notice
This document is copyrighted, 2010. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties that may result from its
use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have been
made in the preparation of this document to assure its accuracy,
AAEON assumes no liabilities resulting from errors or omissions in
this document, or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
Page 3
EPIC Board EPIC-9457 Rev.B
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
z Award is a trademark of Award Software International, Inc.
z CompactFlash™ is a trademark of the Compact Flash
Association.
z Intel
z Microsoft Windows
z ITE is a trademark of Integrated Technology Express, Inc.
z IBM, PC/AT, PS/2, and VGA are trademarks of International
All other product names or trademarks are properties of their
respective owners.
®
, Atom™ are trademarks of Intel® Corporation.
®
is a registered trademark of Microsoft Corp.
Business Machines Corporation.
ii
Page 4
EPIC Board EPIC-9457 Rev.B
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 9657666600 Jumper Cap
• Quick Installation Guide
• Utility CD
• EPIC-9457 Rev.B w/Heatsink
If any of these items should be missing or damaged, please contact
your distributor or sales representative immediately.
iii
Page 5
EPIC Board EPIC-9457 Rev.B
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features....................................................................1-3
1.3 Specifications............................................................1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions....................................................2-2
2.2 Location of Connectors and Jumpers ....................... 2-3
2.3 Mechanical Drawing..................................................2-5
2.4 List of Jumpers.......................................................... 2-7
2.5 List of Connectors ..................................................... 2-8
2.6 Setting Jumpers ........................................................ 2-10
2.7 PCI-104 VIO Voltage Selection (JP1)....................... 2-11
2.8 External AT/ATX Selection (JP2).............................. 2-11
2.9 External LVDS Operating Voltage Selection and External
Power Selection (JP3)..................................................... 2-11
2.10 Touch Screen 4,5,8 Wire Selection (JP4)...............2-11
2.11 COM2 Ring/ +5V/ +12V Selection (JP5).................2-12
2.12 Clear CMOS (JP6) .................................................. 2-12
2.13 Internal LVDS Operating Voltage Selection and Inverter
Power Selection (JP7)..................................................... 2-12
2.14 Internal AT/ATX Selection (S1)...............................2-12
iv
Page 6
EPIC Board EPIC-9457 Rev.B
2.15 Front Panel Connector (CN1) ................................. 2-13
2.16 External LVDS Inverter Power Connector (CN2)....2-13
2.17 External LVDS Connector (CN3) ............................ 2-13
2.18 Standby Power Input (CN4)....................................2-14
2.19 Wide Voltage Power Connector (CN5)...................2-14
2.20 Touch Screen Connector (CN6).............................. 2-14
2.21 Audio Connector (CN7)...........................................2-15
2.22 Internal LVDS Connector (CN9)..............................2-15
2.23 TV-out Connector (CN11).......................................2-16
2.24 USB Connector (CN12)........................................... 2-16
2.25 Internal LVDS Inverter Power Connector (CN13)...2-16
2.26 LPT Port Connector (CN14)....................................2-16
2.27 System Fan Connector (CN15)...............................2-17
2.28 Digital I/O Connector (CN16)..................................2-17
2.29 Power Output Connector (CN17)............................2-18
2.30 PS2 Keyboard/Mouse Connector (CN19)...............2-18
2.31 RS-232 Serial Port Connector (CN21, CN22)......... 2-19
2.32 Standby Power Output Connector (CN23).............. 2-19
2.33 COM1/2 Connectors (CN26)...................................2-19
2.34 Primary EIDE Connector (IDE1) ............................. 2-20
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization. .................................. 3-2
3.2 Award BIOS Setup.................................................... 3-3
v
Page 7
EPIC Board EPIC-9457 Rev.B
Chapter 4 Driver Installation
4.1 Installation.................................................................4-3
Appendix A Programming The Watchdog Timer
A.1 Programming .........................................................A-2
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
st
B.2 1
MB Memory Address Map ................................B-3
B.3 IRQ Mapping Chart................................................B-4
B.4 DMA Channel Assignments...................................B-4
Appendix C Mating Connector
C.1 List of Mating Connectors and Cables.................. C-2
vi
Page 8
EPIC Board EPIC-9457 Rev.B
Chapter
1
General
Information
Chapter 1 General Information 1- 1
Page 9
EPIC Board EPIC-9457 Rev.B
1.1 Introduction
AAEON announces a brand new EPIC Board EPIC-9457 Rev.B,
designed to fit in diverse applications that demand for fitting in
different space limitations and high performance.
EPIC-9457 Rev.B accommodates onboard Intel
®
Atom™ N270
Processor 1.6GHz and the Front Side Bus is 400/533MHz. This
model features DDRII 533 and system memory is up to 1GB.
Moreover, EPIC-9457 Rev.B adopts Intel
®
945GME + ICH7M.
In addition, EPIC-9457 Rev.B deploys Intel
®
ITE8781 chip and
features two RJ-45 ports onboard to display the transcendent
performance of network connections. This new EPIC Express
Board integrated Intel
®
945GME + CH7308 + CH7307C display
chipset to support CRT/LCD simultaneous/ dual view displays.
In addition to the PCI/104-Express and Mini-Card expansions,
EPIC-9457 Rev.B also features two SATA, one Type II
CompactFlash™ for the storage and six USB 2.0 ports, four COM
ports, 8-bit Digital I/O for flexible I/O expansion. EPIC-9457 Rev.B
is an excellent choice for your vital applications.
Chapter 1 General Information 1- 2
Page 10
EPIC Board EPIC-9457 Rev.B
1.2 Features
z Intel® Atom™ N270 Processor
z Intel® 945GME + ICH7M
z Onboard DDRII 533 Memory, Max. 1GB
z Gigabit Ethernet x 2
z Dual 24-bit Dual-channel LVDS LCD
z AC97 2.0 Codec 2CH Audio
z USB2.0 x 6, COM x 4, 8-bit Digital I/O
z SATA x 2, CompactFlash™ x 1
z PCI/104-Express, Mini-Card Expansion Connectors
z Wide DC Voltage Input: 8.5V ~ 19V
Chapter 1 General Information 1- 3
Page 11
EPIC Board EPIC-9457 Rev.B
1.3 Specifications
System
z Form Factor EPIC Express Board
z Processor Onboard Intel
®
Atom™ N270
Processor 1.6GHz, FSB:
400/533MHz
z System Memory Onboard DDRII 533, Max. 1 GB
z Chipset Intel® 945GME + ICH7M
z I/O Chipset ITE8781
z Ethernet Intel® 82574L for
10/100/1000Base-TX, RJ-45 x 2
z BIOS Award Plug & Play SPI BIOS –
2MB ROM
z Wake On LAN Yes
z Watchdog Timer Generates a time-out system reset
z H/W Status Monitoring Supports power supply voltages,
fan speed, and temperature
monitoring
z Expansion Interface PCI/104-Express Expansion
(PCI-104 + PCIe/104) connectors
z Battery Lithium battery
z Power Requirement +8.5V ~ 19V
(Typical)
z Board Size 4.5" x 6.5" (115mm x 165mm)
Chapter 1 General Information 1- 4
Page 12
EPIC Board EPIC-9457 Rev.B
z Gross Weight 1.1 lb (0.5KG)
z Operation Temperature 32°F ~ 140°F (0°C ~ 60°C)
z Storage Temperature -40°F ~ 176°F (-40°C ~ 80°C)
z Operation Humidity 0% ~ 90% relative humidity,
non-condensing
Display: Supports CRT/LCD, CRT/TV, LCD/TV simultaneous/
displays dual view
z Chipset Intel® 945GME integrated +
CH7308 + CH7307C
z Memory Shared system memory up to
224MB
z Resolutions Up to 2048x1536 colors for CRT ,
Up to 1920x1200 @ 24bpp
colors for LCD
z LCD Interface 24-bit dual-channel LVDS
I/O
z Storage SATA x 2,
Type II CompactFlash™ x 1
z Serial Port RS-232 x 3, RS-232/422/485 x 1
z Parallel Port SPP/EPP/ECP Mode
z USB USB2.0 x 6
z PS/2 Port Keyboard+Mouse x 1
z Digital I/O Supports 8-bit (programmable)
z Audio Line-in, Line-out, Mic-in & CD-in
Chapter 1 General Information 1- 5
Page 13
EPIC Board EPIC-9457 Rev.B
Chapter
2
Quick
Installation
Guide
Part No. 2007945722 Printed in Taiwan April 2010
Chapter 2 Quick Installation Guide 2-1
The Quick Installation Guide is derived
from Chapter 2 of user manual. For other
chapters and further installation
instructions, please refer to the user
manual CD-ROM that came with the
product.
Notice:
Page 14
EPIC Board EPIC-9457 Rev.B
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis
Chapter 2 Quick Installation Guide 2-2
Page 15
EPIC Board EPIC-9457 Rev.B
2.2 Location of Connectors and Jumpers
Component Side
Chapter 2 Quick Installation Guide 2-3
Page 16
Solder Side
EPIC Board EPIC-9457 Rev.B
Chapter 2 Quick Installation Guide 2-4
Page 17
EPIC Board EPIC-9457 Rev.B
2.3 Mechanical Drawing
Component Side
Chapter 2 Quick Installation Guide 2-5
Page 18
Solder Side
EPIC Board EPIC-9457 Rev.B
Chapter 2 Quick Installation Guide 2-6
Page 19
EPIC Board EPIC-9457 Rev.B
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Jumpers
Label Function
JP1 PCI-104 VIO Voltage Selection
JP2 External A T/A TX Selection
JP3
JP4 Touch Screen 4,5,8 Wire Selection
JP5 COM2 Ring/+5V/+12V Selection
JP6 Clear CMOS
JP7
S1 Internal AT/ATX Selection
External LVDS Operating Voltage Selection
and External Power Selection
Internal LVDS Operating Voltage Selection
and Inverter Power Selection
Chapter 2 Quick Installation Guide 2-7
Page 20
EPIC Board EPIC-9457 Rev.B
2.5 List of Connectors
The board has a number of connectors that allow you to configure your
system to suit your application. The table below shows the function of
each board's connectors:
Connectors
Label Function
CN1 Front Panel Connector
CN2 External LVDS Inverter Power Connector
CN3 External LVDS Connector
CN4 Standby Power Input
CN5 Wide Voltage Power Connector
CN6 Touch Screen Connector
CN7 Audio Connector
CN9 Internal LVDS Connector
CN10 PCI-104 Connector
CN11 TV-out Connector
CN12 USB Connectors
CN13 Internal LVDS Inverter Power Connector
CN14 LPT Port Connector
CN15 System Fan Connector
CN16 Digital I/O Connector
CN17 Power Output Connector
CN18 PCIe/104 Connector
CN19 PS2 Keyboard/Mouse Connector
CN21 COM3 Connector
Chapter 2 Quick Installation Guide 2-8
Page 21
EPIC Board EPIC-9457 Rev.B
CN22 COM4 Connector
CN23 Standby Power Output Connector
CN24 Gigabit Ethernet Connector
CN25 Gigabit Ethernet Connector
CN26 COM1, COM2 Connector
CN27 VGA + DVI Display Connector
CN29 Compact Flash Disk Connector
CN30 Mini Card Connector
IDE1 Primary EIDE Connector
SATA1 SATA Connector
SATA2 SATA Connector
USB1 USB Connectors
USB2 USB Connectors
Chapter 2 Quick Installation Guide 2-9
Page 22
EPIC Board EPIC-9457 Rev.B
2.6 Setting Jumpers
You configure your card to match the needs of your application by
setting jumpers. A jumper is the simplest kind of electric switch. It
consists of two metal pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect them. To “close” a
jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have
three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2 or 2 and 3.
3
2
1
Open Closed Closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any change.
Generally, you simply need a standard cable to make most
connections.
Chapter 2 Quick Installation Guide 2-10
Page 23
EPIC Board EPIC-9457 Rev.B
2.7 PCI-104 VIO Voltage Selection (JP1)
JP1 Function
1-2 +5V
2-3 +3.3V (Default)
2.8 External AT/ATX Selection (JP2)
JP2 Function
1-2 AT (Default)
2-3 ATX
2.9 External LVDS Operating Voltage Selection and External Power
Selection (JP3)
External Power Selection
JP3 Function
1-3 +5V (Default)
3-5 +12V
LVDS Operating Voltage Selection
JP3 Function
2-4 +5V
4-6 +3.3V (Default)
2.10 Touch Screen 4,5,8 Wire Selection (JP4)
JP4 Function
1-2 4, 8 Wire (Default)
Open 5 Wire
Chapter 2 Quick Installation Guide 2-11
Page 24
EPIC Board EPIC-9457 Rev.B
2.11 COM2 Ring/ +5V/ +12V Selection (JP5)
JP5 Function
1-2 +12V
3-4 Ring (Default)
5-6 +5V
2.12 Clear CMOS (JP6)
JP6 Function
1-2 Protected (Default)
2-3 Clear
2.13 Internal LVDS Operating Voltage Selection and Inverter Power
Selection (JP7)
LVDS Operating Voltage JP7 Function
1-3 +5V
3-5 +3.3V (Default)
Inverter Power JP7 Function
2-4 +5V (Default)
4-6 +12V
2.14 Internal AT/ATX Selection (S1)
Chapter 2 Quick Installation Guide 2-12
Page 25
EPIC Board EPIC-9457 Rev.B
S1 Function
1(ON), 2(OFF) ATX (Default)
1(OFF), 2(ON) AT
2.15 Front Panel Connector (CN1)
Pin Signal Pin Signal
1 Power On Button (+) 2 Power On Button (-)
3 External Buzzer (+) 4 External Buzzer (-)
5 IDE LED (+) 6 IDE LED (-)
7 Power LED (+) 8 Power LED (-)
9 Reset Switch (+) 10 Reset Switch (-)
2.16 External LVDS Inverter Power Connector (CN2)
Pin Signal Pin Signal
1 LCD Inverter Power 2 Backlight Contr ol
3 GND 4 GND
5 Backlight Enable
2.17 External LVDS Connector (CN3)
Pin Signal Pin Signal
1 ENBKL 2 N.C
3 PPVCC 4 GND
5 LVDS1_TXCLK- 6 LVDS1_TXCLK+
7 PPVCC 8 GND
9 LVDS1_TX0- 10 LVDS1_TX0+
11 LVDS1_TX1- 12 LVDS1_TX1+
13 LVDS1_TX2- 14 LVDS1_TX2+
15 LVDS1_TX3- 16 LVDS1_TX3+
Chapter 2 Quick Installation Guide 2-13
Page 26
EPIC Board EPIC-9457 Rev.B
17 N.C 18 N.C
19 LVDS2_TX0- 20 LVDS2_TX0+
21 LVDS2_TX1- 22 LVDS2_TX1+
23 LVDS2_TX2- 24 LVDS2_TX2+
25 LVDS2_TX3- 26 LVDS2_TX3+
27 PPVCC 28 GND
29 LVDS2_TXCLK- 30 LVDS2_TXCLK+
2.18 Standby Power Input (CN4)
Pin Signal
1 PS_ON#
2 GND
3 +5VSB
2.19 Wide Voltage Power Connector (CN5)
Pin Signal Pin Signal
1 PGND 2 PGND
3 DC In 4 DC In
2.20 Touch Screen Connector (CN6)
Pin 8-wire Signal 4-wire Signal 5-wire Signal
1 Ground Ground Ground
2 Top Excite Top UL (Y)
3 Bottom Excite Bottom UR (H)
4 Left Excite Left LL (L)
5 Right Excite Right LR (X)
6 Top Sense N.C SENSE
7 Bottom Sense N.C N.C
Chapter 2 Quick Installation Guide 2-14
Page 27
EPIC Board EPIC-9457 Rev.B
8 Left Sense N.C N.C
9 Right Sense N.C N.C
2.21 Audio Connector (CN7)
Pin Signal Pin Signal
1 MIC 2 MIC_VCC
3 Audio Ground 4 CD_GND
5 LINE_IN L 6 CD_L
7 LINE_IN R 8 CD_GND
9 Audio Ground 10 CD_R
11 LINE_OUT L 12 LINE_OUT R
13 Audio Ground 14 Audio Ground
2.22 Internal LVDS Connector (CN9)
Pin Signal Pin Signal
1 ENBKL 2 N.C
3 PPVCC 4 GND
5 LVDS1_TXCLK- 6 LVDS1_TXCLK+
7 PPVCC 8 GND
9 LVDS1_TX0- 10 LVDS1_TX0+
11 LVDS1_TX1- 12 LVDS1_TX1+
13 LVDS1_TX2- 14 LVDS1_TX2+
15 LVDS1_TX3- 16 LVDS1_TX3+
17 N.C 18 N.C
19 LVDS2_TX0- 20 LVDS2_TX0+
21 LVDS2_TX1- 22 LVDS2_TX1+
23 LVDS2_TX2- 24 LVDS2_TX2+
25 LVDS2_TX3- 26 LVDS2_TX3+
Chapter 2 Quick Installation Guide 2-15
Page 28
EPIC Board EPIC-9457 Rev.B
27 PPVCC 28 GND
29 LVDS2_TXCLK- 30 LVDS2_TXCLK+
2.23 TV-out Connector (CN11)
Pin Signal Pin Signal
1 Y 2 CVBS
3 GND 4 GND
5 C 6 N.C
7 GND 8 N.C
2.24 USB Connector (CN12)
Pin Signal Pin Signal
1 +5V 2 GND
3 USBD5- 4 GND
5 USBD5+ 6 USBD6+
7 GND 8 USBD69 GND 10 +5V
2.25 Internal LVDS Inverter Power Connector (CN13)
Pin Signal Pin Signal
1 LCD Inverter Power 2 Backlight Contr ol
3 GND 4 GND
5 Backlight Enable
2.26 LPT Port Connector (CN14)
Pin Signal Pin Signal
1 #STROBE 2 #AFD
3 DATA0 4 #ERROR
Chapter 2 Quick Installation Guide 2-16
Page 29
EPIC Board EPIC-9457 Rev.B
5 DATA1 6 #INIT
7 DATA2 8 #SLIN
9 DATA3 10 GND
11 DATA4 12 GND
13 DATA5 14 GND
15 DATA6 16 GND
17 DATA7 18 GND
19 #ACK 20 GND
21 BUSY 22 GND
23 PE 24 GND
25 SELECT 26 N.C
2.27 System Fan Connector (CN15)
Pin Signal
1 GND
2 +12V
3 Speed Sense
2.28 Digital I/O Connector (CN16)
Pin Signal Pin Signal
1 Port1 2 Port2
3 Port3 4 Port4
5 Port5 6 Port6
7 Port7 8 Port8
9 +5V 10 GND
Chapter 2 Quick Installation Guide 2-17
Page 30
EPIC Board EPIC-9457 Rev.B
Mapping Table:
BIOS
Setting
Port 8 @684h CN16 Pin 8 GPIO Set 5 / Bit 2 U30 Pin 9 (GPIO 52)
Port 7 @684h CN16 Pin 7 GPIO Set 5 / Bit 1 U30 Pin 10 (GPIO 51)
Port 6 @682h CN16 Pin 6 GPIO Set 3 / Bit 7 U30 Pin 11 (GPIO 37)
Port 5 @682h CN16 Pin 5 GPIO Set 3 / Bit 6 U30 Pin 12 (GPIO 36)
Port 4 @680h CN16 Pin 4 GPIO Set 1 / Bit 4 U30 Pin 31 (GPIO 14)
Port 3 @680h CN16 Pin 3 GPIO Set 1 / Bit 3 U30 Pin 32 (GPIO 13)
Port 2 @680h CN16 Pin 2 GPIO Set 1 / Bit 2 U30 Pin 33 (GPIO 12)
Port 1 @680h CN16 Pin 1 GPIO Set 1 / Bit 1 U30 Pin 34 (GPIO 11)
Digital I/O Address is 680,682,684H
Connector
Definition
Address
IT8781 GPIO
Setting
2.29 Power Output Connector (CN17)
Pin Name Pin Name
1 +12V 2 GND
3 GND 4 +5V
2.30 PS2 Keyboard/Mouse Connector (CN19)
Pin Signal Pin Signal
1 KB_DATA 2 KB_CLK
3 GND 4 +5V
5 MS_DATA 6 MS_CLK
Chapter 2 Quick Installation Guide 2-18
Page 31
EPIC Board EPIC-9457 Rev.B
2.31 RS-232 Serial Port Connector (CN21, CN22)
Pin Signal Pin Signal
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND
2.32 Standby Power Output Connector (CN23)
Pin Signal Pin Signal
1 SMBDAT_SBY 2 GND
3 SMBCLK_SBY 4 GND
5 PS_ON# 6 5VSB
2.33 COM1/2 Connectors (CN26)
Pin Signal Pin Signal
1 DCD1 2 RXD1
3 TXD1 4 DTR1
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1 10 DCD2 (422TXD-/485DATA-)
11 RXD2 (422RXD+) 12 TXD2 (422TXD+/485DATA+)
Chapter 2 Quick Installation Guide 2-19
Page 32
EPIC Board EPIC-9457 Rev.B
13 DTR2 (422RXD-) 14 GND
15 DSR2 16 RTS2
17 CTS2 18 RI2/+5V/+12V
2.34 Primary EIDE Connector (IDE1)
Pin Signal Pin Signal
1 IDE RESET 2 GND
3 DATA7 4 DATA8
5 DATA6 6 DATA9
7 DATA5 8 DATA10
9 DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N.C
21 REQ 22 GND
23 IO WRITE 24 GND
25 IO READ 26 GND
27 IO READY 28 GND
29 DACK 30 GND
31 IRQ15 32 N.C
33 ADDR1 34 UDMA DETECT
35 ADDR0 36 ADDR2
37 CS#1 38 CS#3
39 LED 40 GND
41 +5V 42 +5V
43 GND 44 N.C
Chapter 2 Quick Installation Guide 2-20
Page 33
EPIC Board EPIC-9457 Rev.B
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Main Board/ Daughter Board/ Backplane
有毒有害物质或元素
部件名称
印刷电路板
及其电子组件
外部信号
连接器及线材
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。
铅
(Pb)汞 (Hg)镉 (Cd)
× ○ ○ ○ ○ ○
× ○ ○ ○ ○ ○
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
Chapter 2 Quick Installation Guide 2-21
Page 34
EPIC Board EPIC-9457 Rev.B
Chapter
3
Award
BIOS Setup
Chapter 3 Award BIOS Setup 3-1
Page 35
EPIC Board EPIC-9457 Rev.B
3.1 System Test and Initialization
These routines test and initialize board hardware. If the routines
encounter an error during the tests, you will either hear a few short
beeps or see an error message on the screen. There are two kinds
of errors: fatal and non-fatal. The system can usually continue the
boot up sequence with non-fatal errors. Non-fatal error messages
usually appear on the screen along with the following instructions:
Press <F1> to RESUME
Write down the message and press the F1 key to continue the boot
up sequence.
System configuration verification
These routines check the current system configuration against the
values stored in the CMOS memory. If they do not match, the
program outputs an error message. You will then need to run the
BIOS setup program to set the configuration information in memory.
There are three situations in which you will need to change the
CMOS settings:
1. You are starting your system for the first time
2. You have changed the hardware attached to your system
3. The CMOS memory has lost power and the configuration
information has been erased.
The EPIC-9457 Rev.B CMOS memory has an integral lithium
battery backup for data retention. However, you will need to replace
the complete unit when it finally runs down.
Chapter 3 Award BIOS Setup 3-2
Page 36
EPIC Board EPIC-9457 Rev.B
3.2 Award BIOS Setup
Awards BIOS ROM has a built-in Setup program that allows users
to modify the basic system configuration. This type of information is
stored in battery-backed CMOS RAM so that it retains the Setup
information when the power is turned off.
Entering Setup
Power on the computer and press <Del> immediately. This will
allow you to enter Setup.
Standard CMOS Features
Use this menu for basic system configuration. (Date, t ime, IDE,
etc.)
Advanced BIOS Features
Use this menu to set the advanced features available on your
system.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and
optimize your system performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
(keyboard, mouse etc.)
Power Management Setup
Use this menu to specify your settings for power management.
(HDD power down, power on by ring, KB wake up, etc.)
Chapter 3 Award BIOS Setup 3-3
Page 37
EPIC Board EPIC-9457 Rev.B
PnP/PCI Configurations
This entry appears if your system supports PnP/PCI.
PC Health Status
Use this menu to set PC Health Status.
Frequency/Voltage Control
Use this menu to specify your settings for auto detect DIMM/PCI
clock and spread spectrum.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory
settings for optimal performance system operations. While AWARD
has designated the custom BIOS to maximize performance, the
factory has the right to change these defaults to meet their needs.
Set Password
Use this menu to set Supervisor Password.
Save and Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
You can refer to the "AAEON BIOS Item Description.pdf" file in
the CD for the meaning of each setting in this chapter.
Chapter 3 Award BIOS Setup 3-4
Page 38
EPIC Board EPIC-9457 Rev.B
Chapter
4
Driver
Installation
Chapter 4 Driver Installation 4 - 1
Page 39
EPIC Board EPIC-9457 Rev.B
The EPIC-9457 Rev.B comes with a CD-ROM that contains
all drivers and utilities that meet your needs.
Follow the sequence below to install the drivers:
Step 1 – Install INF Update Utility v8.2.0.1014 Driver
Step 2 – Install Intel Graphics Media Accelerator Driver
Step 3 – Install Intel Ethernet Driver
Step 4 – Install Realtek ALC655 Audio Driver v3.71
Step 5 – Install PenMount 6300 Touch Driver
USB 2.0 Drivers are available for download using Windows
Update for both Windows XP and Windows 2000. For
additional information regarding USB 2.0 support in Windows
XP and Windows 2000, please visit
www.microsoft.com/hwdev/usb/.
Please read instructions below for further detailed
installations.
Chapter 4 Driver Installation 4 - 2
Page 40
EPIC Board EPIC-9457 Rev.B
4.1 Installation:
Insert the EPIC-9457 Rev.B CD-ROM into the CD-ROM Drive. And
install the drivers from Step 1 to Step 5 in order.
Step 1 – Install INF Update Utility v8.2.0.1014 Driver
1. Click on the Step 1 - INF Update Utility v8.2.0.1014
Driver folder and then double click on the Setup.exe
2. Follow the instructions that the window shows
3. The system will help you install the driver automatically
Step 2 – Install Intel Graphics Media Accelerator Driver
1. Click on the Step 2 - Intel Graphics Media Accelerator
Driver folder and select the OS folder your system is
2. Double click on the Setup.exe in the OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 3 – Install Intel Ethernet Driver
1. Click on the Step 3 - Intel Ethernet Driver folder and
select the OS folder your system is
2. Double click on the .exe file in the OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 4 – Install Realtek ALC655 Audio Driver v3.71
1. Click on the Step 4 – Realtek ALC655 Audio Driver
v3.71 folder and select the OS folder your system is
Chapter 4 Driver Installation 4 - 3
Page 41
EPIC Board EPIC-9457 Rev.B
2. Double click on the setup.exe file in the OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Step 5 – Install PenMount 6300 Touch Driver
1. Click on the Step 5 – PenMount 6300 Touch Driver
folder and select the OS folder your system is
2. Double click on the Setup.exe file in the OS folder
3. Follow the instructions that the window shows
4. The system will help you install the driver automatically
Chapter 4 Driver Installation 4 - 4
Page 42
EPIC Board EPIC-9457 Rev.B
A
Appendix
Programming the
Watchdog Timer
Appendix A Programming the Watchdog Timer A-1
Page 43
EPIC Board EPIC-9457 Rev.B
A.1 Programming
EPIC-9457 Rev.B utilizes ITE 8781 chipset as its
watchdog timer controller. Below are the procedures to complete
its configuration and the AAEON initial watchdog timer
program is also attached based on which you can
develop customized program to fit your application.
Configuring Sequence Description
After the hardware reset or power-on reset, the ITE 8781 enters the
normal mode with all logical devices disabled except
KBC. The initial state (enable bit ) of this logical device (KBC) is
determined by the state of pin 121 (DTR1#) at the falling edge of
the system reset during power-on reset.
Appendix A Programming the Watchdog Timer A-2
Page 44
EPIC Board EPIC-9457 Rev.B
There are three steps to complete the configuration setup: (1) Enter
the MB PnP Mode; (2) Modify the data of configuration re gisters; (3)
Exit the MB PnP Mode. Undesired result may occur if the MB PnP
Mode is not exited normally.
(1) Enter the MB PnP Mode
To enter the MB PnP Mode, four special I/O write operations are to
be performed during Wait for Key st ate. To ensure the initial state of
the key-check logic, it is necessary to p erform four write opera-tio ns
to the Special Address port (2EH). Two different enter keys are
provided to select configuration ports (2Eh/2Fh) of the next step.
(2) Modify the Data of the Regist ers
All configuration registers can be accessed after entering the MB
PnP Mode. Before accessing a selected register, the content of
Index 07h must be changed to the LDN to which the register
belongs, except some Global registers.
(3) Exit the MB PnP Mode
Set bit 1 of the configure control register (Index=02h) to 1 to exit the
MB PnP Mode.
Appendix A Programming the Watchdog Timer A-3
Page 45
EPIC Board EPIC-9457 Rev.B
WatchDog Ti mer Configuration Registers
Configure Control (Index=02h)
This register is write only. Its values are not sticky; that is to say, a
hardware reset will automatically clear the bits, and does not
require the software to clear them.
Watch Dog Timer 1, 2, 3 Control Register (Index=71h,81h,91h
Default=00h)
Appendix A Programming the Watchdog Timer A-4
Page 46
EPIC Board EPIC-9457 Rev.B
Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h,
82h, 92h Default=001s0000b)
Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register
(Index=73h,83h,93h, Default=38h)
Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register
(Index=74h,84h,94h Default=00h)
Appendix A Programming the Watchdog Timer A-5
Page 47
EPIC Board EPIC-9457 Rev.B
A.2 ITE8781 Watchdog Timer Initial Program
.MODEL SMALL
.CODE
Main:
CALL Enter_Configuration_mode
CALL Check_Chip
mov cl, 7
call Set_Logic_Device
;time setting
mov cl, 10 ; 10 Sec
dec al
Watch_Dog_Setting:
;Timer setting
mov al, cl
mov cl, 73h
call Superio_Set_Reg
;Clear by keyboard or mouse interrupt
mov al, 0f0h
mov cl, 71h
call Superio_Set_Reg
;unit is second.
mov al, 0C0H
mov cl, 72h
Appendix A Programming the Watchdog Timer A-6
Page 48
EPIC Board EPIC-9457 Rev.B
call Superio_Set_Reg
; game port enable
mov cl, 9
call Set_Logic_Device
Initial_OK:
CALL Exit_Configuration_mode
MOV AH,4Ch
INT 21h
Enter_Configuration_Mode PROC NEAR
MOV SI,WORD PTR CS:[Offset Cfg_Port]
MOV DX,02Eh
MOV CX,04h
Init_1:
MOV AL,BYTE PTR CS:[SI]
OUT DX,AL
INC SI
LOOP Init_1
RET
Enter_Configuration_Mode ENDP
Exit_Configuration_Mode PROC NEAR
MOV AX,0202h
Appendix A Programming the Watchdog Timer A-7
Page 49
EPIC Board EPIC-9457 Rev.B
CALL Write_Configuratio n_Data
RET
Exit_Configuration_Mode ENDP
Check_Chip PROC NEAR
MOV AL,20h
CALL Read_Configuration_Data
CMP AL,87h
JNE Not_Initial
MOV AL,21h
CALL Read_Configuration_Data
CMP AL,81h
JNE Not_Initial
Need_Initial:
STC
RET
Not_Initial:
CLC
RET
Check_Chip ENDP
Read_Configuration_Data PROC NEAR
MOV DX,WORD PTR CS:[Cfg_Port+04h]
Appendix A Programming the Watchdog Timer A-8
Page 50
EPIC Board EPIC-9457 Rev.B
OUT DX,AL
MOV DX,WORD PTR CS:[Cfg_Port+06h]
IN AL,DX
RET
Read_Configuration_Data ENDP
Write_Configuration_Data PROC NEAR
MOV DX,WORD PTR CS:[Cfg_Port+04h]
OUT DX,AL
XCHG AL,AH
MOV DX,WORD PTR CS:[Cfg_Port+06h]
OUT DX,AL
RET
Write_Configuration_Data ENDP
Superio_Set_Reg proc near
push ax
MOV DX,WORD PTR CS:[Cfg_Port+04h]
mov al,cl
out dx,al
pop ax
inc dx
out dx,al
ret
Superio_Set_Reg endp.Set_Logic_Device proc near
Appendix A Programming the Watchdog Timer A-9
Page 51
EPIC Board EPIC-9457 Rev.B
Set_Logic_Device proc near
push ax
push cx
xchg al,cl
mov cl,07h
call Superio_Set_Reg
pop cx
pop ax
ret
Set_Logic_Device endp
;Select 02Eh->Index Port, 02Fh->Data Port
Cfg_Port DB 087h,001h,055h,055h
DW 02Eh,02Fh
END Main
Note: Interrupt level mapping
0Fh-Dh: not valid
0Ch: IRQ12
.
.
03h: IRQ3
02h: not valid
01h: IRQ1
00h: no interrupt selected
Appendix A Programming the Watchdog Timer A-10
Page 52
EPIC Board EPIC-9457 Rev.B
Appendix
B
I/O Information
Appendix B I/O Information B-1
Page 53
EPIC Board EPIC-9457 Rev.B
B.1 I/O Address Map
Appendix B I/O Information B-2
Page 54
EPIC Board EPIC-9457 Rev.B
B.2 1st MB Memory Address Map
Appendix B I/O Information B - 3
Page 55
EPIC Board EPIC-9457 Rev.B
B.3 IRQ Mapping Chart
B.4 DMA Channel Assignments
Appendix B I/O Information B-4
Page 56
EPIC Board EPIC-9457 Rev.B
Appendix
C
Mating Connecotor
Appendix C Mating Connector C - 1
Page 57
EPIC Board EPIC-9457 Rev.B
C.1 List of Mating Connectors and Cables
The table notes mating connectors and available cables.
Connector
Label
Function
Mating Connector
Vendor Model no
Available
Cable
Cable P/N
CN1 Front Panel
Connector
CN2 LCD
Inverter
Connector
CN3 LVDS
Connector
CN4 Standby
power input
CN5 Power
Connector
CN6
CN7 Audio
CN9 LVDS
CN11
CN12 USB
Touch
Screen
Connector
Connector
Connector
TV-out
Connector
Connector
LIAN
TAY
CATCH
Hirose 1.25mm Pitch 30
JST 2.54mm Pitch 3 pins
LIAN
TAY
LIAN
TAY
CATCH 2.0mm pitch 14pins
Hirose 1.25mm Pitch 30
CATCH 2.00mm Pitch 8 pins
CATCH 2.00mm Pitch 10
1.25mm Pitch 10
pins (LIAN TAY
H752-10 or
compatible)
2.0mm pitch 5 pin
(CATCH HS-5P-2.0
or compatible)
pins ( CATCH H716
or compatible)
(JST XHP-3 or
compatible)
4.2mm pitch 4pins
(LIAN TAY H756-04
or compatible)
1.0mm pitch 9pins
(LIAN TAY H746-09
or compatible)
( CATCH H709-2 or
compatible)
pins ( CATCH H716
or compatible)
( CATCH H754-2x4
or compatible)
pins ( CATCH
H754-2x5 or
compatible)
Front
Panel
cable
N/A N/A
N/A N/A
Power
input
cable
Power
cable
N/A N/A
Audio
Cable
N/A N/A
TV-Out
Cable
USB
Cable
N/A
170220020B
1702040151
1700140510
1700080180
1709100208
Appendix C Mating Connector C - 2
Page 58
EPIC Board EPIC-9457 Rev.B
CN13 LCD
Inverter
Connector
CN14 LPT port
Connector
CN15
CN16
CN17
CN19
CN21
CN22
IDE1 Primary
System Fan
Connector
Digital I/O
Connector
Power
Output
Connector
PS2
Keyboard/M
ouse
Connector
COM3
Connector
COM4
Connector
EIDE
Connector
CATCH 2.0mm pitch 5 pin
(CATCH HS-5P-2.0
or compatible)
CATCH 2.00mm Pitch 26
pins ( CATCH
H754-2x13 or
compatible)
HoBase 2.54mm pitch 3 pins
(HoBase 2543-WS-3
or compatible)
CATCH 2.00mm Pitch 10
pins ( CATCH
H754-2x5 or
compatible)
HoBase 2.54mm pitch 4 pins
(HoBase 2543-H-4 or
compatible)
CATCH 2.0mm pitch 6 pins
( CATCH MD-6PS or
compatible)
LIAN
TAY
LIAN
TAY
CATCH 2.00mm Pitch 44
1.25mm pitch 9 pins
(LIAN TAY H752-09
or compatible)
1.25mm pitch 9 pins
(LIAN TAY H752-09
or compatible)
pins ( CATCH
H820-2 or
compatible)
N/A N/A
LPT cable 1701260308
N/A N/A
N/A N/A
Power
output
cable
Keyboard
/ Mouse
Cable
COM
Cable
COM
Cable
EIDE
Cable
1702040109
1700060152
1701090150
1701090150
1701440500
Appendix C Mating Connector C - 3
Loading...