3plus Elite Vibe User Manual

OWNER’S MANUAL

1

Overview

1) Operating conditions

2) Articles in the box

3) Charging

4) App setup

5) Wearing the device

6) Cleaning the device

7) Screen operation

8) Device operation
a) Time/date interface
b) Activity
c) Heart rate
d) Record workout
e) Sleep tracker
f) Notifications
g) APPS

9) Customer support

10) Troubleshooting

11) Supported devices

12) Product specifications

13) Remarks

2

1. Operating Conditions

Operating temperature

-13°F to 131°F (-25°C to 55°C)

Water resistance

The 3Plus Lite is IP62 water resistant rated. This means
that the watch can we worn during daily cleansing or in
midst of rain but we do not recommend it. Do not wear the
band in the shower or submerge it under water.

Battery

Up to 7 days of battery life.

3

2. Articles in the box

A B C

D E

A：VIBE Smartwatch

B：Quick Start Guide

C：Charging cradle

D：Micro-USB cable

E：Owner’s Manual

4

3. Charging

1. Position the charging cradle to connect to the back of

your tracker while making sure the pins match the contact
points on the device and the charging cradle. The
magnetic attraction should then snap them together in
place.

2. Insert the micro-USB cable into the charging cradle,

and then connect the USB plug into a power source. A
"Charging" icon will be shown on the screen to indicate
that it’s charging.

Tip: Make sure to completely charge your device
before first use. A full charge will take approximately
two hours (depending on the power source).

5

4. App Setup

To set up your band with a mobile
device, you must first download and
install the 3PLUS ELITE APP from either
the Apple APP store or Google Play
store.

Connecting the APP

1. Turn on the Bluetooth on your mobile device (if

not already on).

2. Open the 3PLUS ELITE APP on your mobile device.

a. If you are a new member, you will need to register
a new account. Be sure to enter your personal
information accurately in the given prompts.
b. If you are an existing member, you can just input
your login email address and password.

3. After logging in, choose the 3PLUS-VIBE option to

start the pairing process.

4. Select the detected VIBE # code. This should be the

same code that shows up on your VIBE device's screen.
(Note: The tracker must be near your mobile phone in
order for it to detect it.)

6

5. A connection request will be shown on your

smartwatch. Tap on the green check mark to confirm the
Bluetooth pairing.

6. When the tracker is connected successfully, both

your tracker and mobile device will receive a notification.

If the connection is not successful, please repeat the same
steps to try again.

(Note: The Bluetooth pairing is a one-time process. If you
would like to connect the band with a different account,
you must un-pair the existing connection first through the
App settings.)

7

5. Wearing the Device

1. Wrap the device around your wrist and pull the band
through the hole in the buckle.

2. Pull the band until the device feels slightly tight on
your wrist but it should be able to slide slightly back
and forth on your wrist.

3. Insert the buckle pin through one of the band's holes
to secure the band in place.

4. You may use the clamp to further secure the bands
together.

8

6. Cleaning the Device

Make sure to clean regularly
It is strongly recommended to regularly clean your device’s
band after workouts or prolonged use. Moisture from
sweat and dirt from other means can build up underneath
the band and can cause skin irritation.

Use water or rubbing alcohol
DO NOT use soaps, sanitizers, or household cleaners to
clean the band.

Dry the band before use
Make sure to clean and dry the band well before putting it
back on.

9

7. Screen Operation

Turn on the device by either double tapping the screen or
pressing one of the side buttons.
The device will only respond when the specific sensor area
is tapped.
The screen will turn off after 10 seconds of inactivity.

Hold down both buttons simultaneously for 3 seconds to
completely turn off the device.
Perform the same action again to turn it back on.

10

Screen operations can be performed by touching the
screen with your finger tip and with the two side buttons.
Slide left or right on the screen's surface to change the
screen and menu options.

Press the left side button to go back to the main screen,
and the right side button to back to the previous screen.