Scotchlok
Instructions
™
Connectors and Tools
July 1994
Issue 2, 80-6107-4684-6
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Scotchlok
Connector
TM
Connection
Type
Maximum
Insulation
O. D.
in
mm
Butt Splicing
PIC-unfilled
AWG
mm
Cable Type
PIC-filled Pulp or Paper
AWG mm
AWG
Approved Tools
To reduce fatigue, use tool within each splicing
group with highest mechanical advantage
indicated in ( ).
mm
*
UR2
**
UR2-D
*
UY2
**
UY2-D
***
UP2
***
UP3
*
211
*
UB2A
**
UB2A-D
***
UPB
.082 2.08 19-26 .9-.4
.082 2.08
.082 2.08
.082 2.08
.060
.066 1.67 22-26 .7-.4 19-26 .9-.419-26
.082 2.08 19-26 .9-.4 19-26 .9-.4 19-26 .9-.4
19-26 .9-.4 19-26 .9-.4
19-26 .9-.4
19-26 .9-.4
1.52
22-26 .7-.4
19-26 .9-.4 N A
19-26 .9-.4
19-26 .9-.4 19-26 .9-.4
22-26 .7-.4 22-26 .7-.4
.9-.4
19-26 .9-.4
N A
Tap Splicing
.082 2.08
.082 2.08
.050
19-26 .9-.4 19-26 .9-.4 N A
19-26 .9-.4 19-26 .9-.4 19-26 .9-.4
1.27
22-26 .7-.4
24-26 .5-.4
Can be used on 22 (.7)
foam insulated cable
22-26 .7-.4
E-9BM
(10-1)
E-9C/CW (7-1)
E-9E (4-1)
•
E-9Y (3-1)
E-9E (4-1) E-9BM (10-1) E-9Y (3-1)
E-9BM
(10-1)
E-9E (4-1)
E-9Y (3-1)
In Line Splicing
*
UDW2
.175 4.4
Self-stripping drop wire connector designed to accommodate
copper or copper clad steel conductors 16-19 AWG (1.3-0.9 mm)
in strain relief areas. Ideal for use on Alpha Duct GT-7,
Alpha TEL, F-Drop and C-Drop.
E-9BM
(10-1)
Clear / Cap Only
*
UCC
***
UPC
Filled
*
Unfilled
**
Unfilled - Flame Retardant
***
.060 1.52
.060
1.52
22-26 .7-.4 22-26 .7-.4 N A
22-26
22-26 .7-.4
.7-.422-26
Note: For health and safety information for
sealant in filled Scotchlok Connectors,
see package label or appropriate Material
Safety Data Sheet.
.7-.4
ALL TOOLS APPROVED FOR
BUTT SPLICING MAY BE USED
NA Not Applicable
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
UR2 UR2-D UY2 UY2-D UP2 UP3 UCC UPC
Trim, straighten
conductors
211
Connector to be
removed
Place 211
connector
UB2A UB2A-D UPB
Place side slot
on run wire
Pre-crimp
UDW2
Cut and slit
drop wire 1- 1/4''
Separate, fully
insert conductors
Insert fully
matching line or
ribs of drop wire
Pre-crimp
Twist, cut, insert
tap wire
Crimp with cap
side down
Pre-crimp
raised side
Pre-crimp
Crimp with cap
side down
Test port
Crimp with cap
side down
Crimp with cap
side down
REMEMBER
On ratchet tools
(E-9C, E-9CH )
Squeeze handle until
ratchet releases
E9Y tool should not be used when
•
To reduce fatigue,
use tool with highest
mechanical advantage
Periodically gauge
tools and
connectors
•
crimping three 19 AWG/ .9 mm conductors
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...