3M UMUV10-045V2 User Manual

User Manual
Innovative LCD Display Solutions
AP
DP
OP
10AV Series
10AV Series
10AV Series
UMUV.10-045V2
Apr 05
P.1
AP-10AV / DP-10AV / DP-10AV Series User Manual
1. Table of Content
1. Table of Content Page.1
2. Introduction
A) Overview Page.2 B) Features Page.2 C) Dimension Diagrams Page.3-5 D) Technical Specifications Page.6
3. Installation
A) Package Contents Page.7 B) Caution to the user Page.7 C) Cleaning Page.7 D) Precautions Page.8-9
4. Using the System
A) Product Views Page.10-12 B) I/O Outlet Page.13 C) Installation Procedures Page.14 D) Setup Touchscreen (Optional) Page.15
i) For Windows Page.15
ii) For DOS Page.16-18 E) OSD Switch Page.19 F) OSD Control (VGA Version) Page.20-22 G) OSD Control (Video Version) Page.23-27
Apr 05
P.2
AP-10AV / DP-10AV / DP-10AV Series User Manual
2. Introduction
A. Overview
This LCD monitor incorporates 10.4color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. A maxi­mum resolution of 800 x 600 is ideal for displaying complex graphics and high definition images. Other outstanding designs that enhance this LCD monitors performance are Plug & Play compatibility and OSD (On Screen Display) controls.
B. Features
High contrast color TFT LCD display support resolution up to 800 x 600.
Advanced OSD control for picture quality adjustment.
Detachable stand for wall-mounting application.
Optional Composite and S-Video input
Slim and compact size
Wide Viewing Angle
Disclaimer This information is subject to change without notice. The producer of this manual accepts no responsibility for damage or claims, resulting from misuse or misinterpretation
Apr 05
P.3
AP-10AV / DP-10AV / DP-10AV Series User Manual
2. Introduction
C. Dimension Diagrams
AP-10AV series
Apr 05
P.4
AP-10AV / DP-10AV / DP-10AV Series User Manual
2. Introduction
C. Dimension Diagrams
DP-10AV series
Apr 05
P.5
AP-10AV / DP-10AV / DP-10AV Series User Manual
2. Introduction
C. Dimension Diagrams
OP-10AV series
Apr 05
P.6
AP-10AV / DP-10AV / DP-10AV Series User Manual
2. Introduction
Technical Specifications
Panel 10.4" LCD Panel Display Type TFT LCD active matrix colour Resolutions 800 x 600 Response Time Tr=15ms, Tf=25ms Contrast Ratio 180:1 typical Brightness 350 cd/m2 typical
Monitor
Pixel Pitch 0.264(H) x 0.264(V)
Power Supply
Connectors
Panel Colour 262,144 display colour Viewing Angle 60 / 60 / 55 / 40 (L / R / U / D) Storage Temp. -20° to 60°C Operating Temp. 0° to 50°C MTBF 50,000 hours Remote Adapter 110V - 220V AC Input Adapter Size 108(L) x 60 (W) x 30(D) mm
Cable Length from mains plug to adapter
Cable Length from adapter Unit
182cm
180cm
Power Socket 12V (+) female RCA Composite video input (female) x 1 S-Video MiniDIN 4-pin (female) x 1 VGA HDDB 15-pin (female) x 1
Video
Standards Supports NTSC, PAL or SECAM AP Series : 275(W) x 215(H) x 51(D) mm
Product Dimension
DP Series : 258.5(W) x 198.5(H) x 42.7(D) mm OP Series : 285(W) x 225(H) x 41(D) mm
Packing Dimension
AP / DP / OP Series : 480(L) x 362(W) x 85(H) mm
AP Series : 2.5 / 4.5 Kg
Net / Gross Weight
DP Series : 2 / 4 Kg OP Series : 2 / 4 Kg
The Federal Communications Commission warns the user that any
Apr 05
P.7
AP-10AV / DP-10AV / DP-10AV Series User Manual
3. Installation
A. Package Contents
After unpacking the carton, check and see if the following items are included in good condition. Contact your supplier as soon as possible for replacing the missing / damaged items.
10.4 TFT LCD monitor
RCA Cable (Optional For AV Version only)
S-Video Cable (Optional For AV Version only)
VGA Cable (Male to Male)
DC 12V Adapter (5A)
Power Cord
Mounting Bracket (AP Series only)
User Manual
CD Disc
B. Caution to The User
To assure continued FCC compliance, please use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a shielded BNC (5) cable. Also,
unauthorized changes or modifications to the unit if not expressly approved by the party responsible for compliance could void the user's authority of operating the equipment.
C. Cleaning
1. Gently wipe screen with a clean camel hair lens brush, or a soft, clean, lint-free cloth. This removes dust and other particles that can scratch the screen.
2. Do not apply excessive pressure to the screen surface when wiping it clean because this may damage the LCD.
3. Do not pour or spray any liquid directly onto the screen or case of the LCD monitor. Chemical cleaners have been reported to damage the screen or case of the LCD monitor.
Apr 05
P.8
AP-10AV / DP-10AV / DP-10AV Series User Manual
3. Installation
D. Precautions
Read all of these instructions and save them for later use. Follow all warnings and instructions on the product.
Product
Do not cover or block the vent holes in the case.
Do not insert sharp objects or spill liquid into the LCD monitor through
cabinet slots. They may cause accident fire, electric shock or failure.
Disconnect the power plug from the AC outlet if you will not use it for an
indefinite period of time.
Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
Do not touch the screen directly with your fingers. You may damage the
screen, and oil from your skin in difficult to move.
Do not apply pressure to screen. The LCD is very delicate.
Power
1. Use the type of power indicated on the marking label.
Plugs
1. Do not remove any of the prongs of the monitors three-pronged power
plug.
2. Disconnect the power plug from the AC outlet under following
conditions
If the product will not be used for an indefinite period time.
When the power cord or plug is damaged or frayed.
If the product does not operate normally when the operating
instructions are followed.
Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance, indicating a
need for service.
Apr 05
P.9
AP-10AV / DP-10AV / DP-10AV Series User Manual
3. Installation
D. Precautions (Cont.)
Power and extension cords
1. Do not allow anything to rest on the power cord.
2. Do not locate this product where persons will walk on the cord.
3. Use the proper power cord with correct attachment plug type. If the
power source is 120V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European countrys safety regulations, such as VDE for Germany.
4. Do not overload wall outlets or power cords. Ensure that the total of all
units plugged into the wall outlet does not exceed 10 amperes.
5. Ensure that the total ampere ratings on all units plugged into the
extension cord is not above the cords rating.
6. If the power supply cord, which came with your monitor, is to be
connected to the PC instead of the wall outlet, this equipment is to be used with UL/TÜV approved computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A(minimum).
Environment
1. Place the monitor on a flat and leveled surface.
2. Place the monitor in a well-ventilated place.
3. Keep the monitor away fromOverly hot, cold or humid places, places
directly under sunlight, dusty surroundings, equipment that generate strong magnetic fields.
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.10
3. Installation
A. Product Views
AP Series - Front View
AP Series - Rear View
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.11
3. Installation
A. Product Views (Cont.)
DP Series - Front View
DP Series - Rear View
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.12
3. Installation
A. Product Views (Cont.)
OP Series - Front View
OP Series - Rear View
Apr 05
P.13
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
B. I/O Outlet
AP Series
DP Series
OP Series
(1)
1. DC IN Connect to DC power cable.
2. PC IN Connect to D-Sub 15 pin signal connector.
3. RCA IN Connect to the composite cable connector. (for AV series only)
4. S-Video IN Connect to the S-Video cable connector. (for AV series only)
5. USB IN Connect to the USB connector. (for Touchscreen series only)
6. SERIAL IN Connect to the Serial connector. (for Touchscreen series only)
(2)
(3)
(4)
(5)
(6)
Apr 05
P.14
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
C. Installation Procedures
This monitor is equipped with an auto-sensing power supply for voltage ranges 100~240V, 50~60Hz. Please follow the following instruction to install LCD monitor.
1. Make sure that the system power is turned off.
2. Plug the signal cable to the signal connector at the rear of
PC and the rear of the LCD monitor.
3. Plug adapter output cable to the jack at the rear of LCD
monitor and the power cord to the adapter.
4. Connect the power cord to power source.
5. Turn on the computer and the monitor.
6. Then push the OSD menu button and use the Auto Adjust
function to fine the best mode of your computer.
Apr 05
P.15
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
D. Setup Touchscreen
Touchscreen used for UltraView products are manufactured by 3M. Here provide TouchWare
TM
Software includes touch screen drivers for your installing.
Note: To configure the settings of the touchscreen, please refer to the TouchWare
TM
User Guideline
Note: If you have a Microsoft® IntelliPoint® or Kensington® Mousework® PS/2 mouse, installing TouchWare
TM
software will disable the special mouse
functionally of these devices
For Windows 95, 98, Me, NT4.0, 2000 & XP
1. Open the driver CD provided along with the product or download the driver from our Website.
2. Make sure you have completed the appropriate hardware connections.
3. Power on your system. Make sure no other application are opened.
4. Double click the TW564SR4.exe files.
5. Unzip the file and save it in a default folder
Note: Remember the path of the default folder or create a new folder by your decision.
6. Follow the onscreen instructions to begin the installation.
Note: Choose Express option for automatically installs the required TouchWare
TouchWare TouchWareTM will also determine multiple monitor configurations at this time.
Note: For details of Custom option, please refer to the website of 3M and download the
user guide of TouchWare (http:// www.3m.com/3MTouchSystems/downloads/tecdoc.jhtml)
software files, create a TouchWare
TM
software icon on the Windows desktop and control panel.
TM
software.
TM
software program files, and place a
TM
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.16
4. Using the System
D. Setup Touchscreen
For Windows 95, 98, Me, NT4.0, 2000 & XP (Cont.)
7. Once installation is complete, restart the system. As the system restarts, Windows detects and loads the driver.
For serial controllers, restart the system. As the system restarts, Win-
dows detects and load the driver
Note: This step is not necessary for Windows 2000 or above system, The driver loads
automatically.
For USB controllers, connect the touch screen cable to the USB port in
your computer. After a few seconds, the system beeps to indicate it has detected the touch screen and loaded the driver.
For DOS
When you install Touchware from DOS, the Install program only loads the touchscreen files specific to DOS. The installation includes the following files:
Touchscreen driver for DOS
Touchscreen control panel for DOS
Pen Configuration utility for DOS
Microcal Diagnostic utility
ThruGlass control panel for DOS
DOS help files
If you do not plan to use any of the touchscreen files for windows, you may want to install just the DOS touchscreen files.
1. Open the driver CD provided along with the product or download the driver from our Website.
2. Make sure you have completed the appropriate hardware connections. If not, the Install program cannot properly configure the touchscreen.
3. Close all applications and exit from Windows.
4. Insert the TouchWare Disk into a diskette drive.
5. Access the DOS command line prompt.
6. Change to the drive that has the TouchWare diskette. For example, enter A: if you inserted the TouchWare diskette in Drive A.
Apr 05
P.17
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
D. Setup Touchscreen
For DOS (Cont.)
7. Type INSTALL followed by the source disk drive, the destination drive, and the destination directory.
For example, the following command copies the files from Drive A (source drive) to Drive C (destination drive) and the \MTS\TOUCH directory :
INSTALL A: C:\MTS\TOUCH
8. Press Enter. The system reports that it is about to copy the DOS touchscreen files and prompt for confirmation that you want to continue.
9. Press C to start the installation.
First, the Install program copies all DOS touchscreen files from the
TouchWare diskette to the specified destination drive and directory.
Next, the Install program automatically searched through the system
and configures the touchscreen to the proper COM port, interrupt, and communication rate.
Finally, the Install program prompts if you want it to automatically modify
your AUTOEXEC.BAT file
If you let the Install program modify your AUTOEXEC.BAT file, the system automatically loads the DOS touchscreen driver whenever you start your computer.
If you do not let the Install program modify your AUTOEXEC.BAT file, you must load the DOS touchscreen driver before using a DOS touch application. For more information, refer to Loading the DOS Touchscreen Driver in the next page
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.18
4. Using the System
D. Setup Touchscreen
For DOS (Cont.)
Loading the DOS Touchscreen Driver
After you install the files for the DOS touchscreen driver, you must load the driver before you can run a DOS touch application or open the DOS Touchscreen control panel.
You can run the DOS touchscreen driver from a full-screen DOS session within Windows. However, the Windows touchscreen driver cannot be running. Error message reads: Windows x.x is running in 386 Enhanced mode. Device not found.
This means either the Windows Touchscreen driver is loaded or the COM port/ IRQ designations are incorrect.
You can manually load the DOS touchscreen driver when needed, or you can let the system automatically load the driver when you start up your computer.
To manually load the DOS touchscreen driver:
1. Close all applications and exit from Windows.
2. Access the DOS command line prompt.
3. Use the Change Directory (cd) command to switch to the directory that has the DOS touch driver files. By default, the Install program loads TouchWare into the C:\MTS|TOUCH directory.
4. Type DOSTOUCH and then press Enter. The system displays a message that the driver is now installed. For example:
MicroTouch Mouse Emulator - Version x.x
Copyright © 1990 - 1997 MicroTouch Systems, Inc. Driver Installed
To automatically load the DOS touchscreen driver when you start up your
computer, add the following line to your AUTOEXEC.BAT file :
drive-designator :\directory\DOSTOUCH
where drive-designator and directory define the location (disk and path) of the files for the DOS touchscreen. For example:
Apr 05
P.19
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
E. OSD Switch
Menu/Selection Power
Left
Right
Exit
Input Select: This button is used to select CVBS for composite
video input, RGB for VGA input and S-Video for Super-Video input
OSD Menu: This button is used to enter OSD main Menu
Increase(à): This button is used to adjust the increasing or
next value of selected OSD control option.
Decrease(ß): This button is used to adjust the decreasing or
next value of selected OSD control option.
Power Switch: This button is used to power ON/OFF the LCD
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.20
4. Using the System
F. OSD Control For VGA Input Vesion
LCD Membrane Diagram
Menu/Selection Power
Left
Right
Exit
MAIN MENU
BRIGHT/CONTRAST AUTO ADJUST PHASE/CLOCK H/V POSITION MISC RESET
Main Menu
Bright / Contrast
To enter into the Bright, Black level & Contrast sub-menu
Auto Adjust
To perform automatic optimisations of all functions
An Adjusting message is displayed during the process
Phase / Clock
To enter into the phase & clock sub menu
H/V Position
To enter into the Position sub-menu
MISC
To enter into the MISC sub-menu
Reset
Reset to the default factory settings
Apr 05
P.21
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
F. OSD Control For VGA Input Version
Bright / Contrast
1. Brightness
To perform brightness adjustment of the input RGB signal
Use the Left & Right button to adjust and button to Brightness
2. Contrast
To adjust the contrast level of the input signal
Use the Left & Right button to adjust and button to Contrast
Phase / Clock
1. Phase
To adjust input video sampling clocks phase
Use the Left & Right button to adjust and button to Phase
2. Clock
To adjust input video sampling clock
Use the Left & Right button to adjust and button to Clock
H/V Position
1. H.Position
To adjust the horizontal size of the frame
Use the Left & Right button to adjust and button to H.position.
2. V.Position
To adjust the vertical position of the frame
Use the Left & Right button to adjust and button to V.position.
Apr 05
P.22
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
F. OSD Control For VGA Input Version
MISC
1. Information
The first header row shows the current resolution setup
The second header row shows the horizontal frequency of the current
input signal
The third header row shows the vertical frequency of the current input
signal
2. OSD Timer
To modify the duration of the OSD time-out
3. Color a) 5500K
Select Colour Temp at 5500K
b) 6500K
Select Colour Temp at 6500K
c) 9500K
Select Colour Temp at 9500K
d) User
Change Colour Temp by manual
4. Language
To select the language of OSD menu 7 Languages :
(1) English (2) Japanese (日本語)
(3) Chinese (中文) (4) German
(5) Francais (6) Espanol (7) Italiano
Apr 05
P.23
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
G. OSD Control For Video Input Version
Colour Configuration Page
Colour
Brightness Contrast Colour Adjust Exit
Brightness Adjust the brightness value from 1 to 100 using (à)
and (ß) buttons.
Contrast
Adjust the contrast value from 1 to 100 using (à) and (ß) buttons.
Colour Adjust
Select the colour temperature option for 9300K or 6500K or RGB
Exit
Exit the Colour configuration Page
Apr 05
P.24
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
G. OSD Control For Video Input Version
Picture Configuration Page
Picture
H.Position V.Position Sharpness Phase Clock Exit
H.Position
Press (à) shifting display image to right with value from 0 to 100; Press (ß) shifting display image to left from value 0 to 100.
V.Position
Press (à) shifting display image to upward with value from 0 to 100; Press (ß) shifting display image to downward from value 0 to 100.
Sharpness
Adjust the sharpness of the S-Video and CVBS image with 5 levels
Phase
Adjust the phase of PPL clock by using (à) and (ß) buttons
Clock
Adjust clock rate to improves colour display by using (à) and (ß) buttons
Exit
Exit the Picture configuration Page
AP-10AV / DP-10AV / DP-10AV Series User Manual
Apr 05
P.25
4. Using the System
G. OSD Control For Video Input Version
Function Configuration Page
Function
Auto Adjust Auto Position Auto Phase Auto Clock Exit
Auto Adjust
Enable or disable function for auto adjusting brightness, contrast, color etc. YesEnable NoDisable
Auto Position
Enable or disable function for auto adjusting horizontal position or vertical position
YesEnable No Disable
Auto Phase
Enable or disable function for auto adjusting physical voltage to improves focus, clarity and image stability
YesEnable NoDisable
Auto Clock
Enable or disable function for auto adjusting to clock rate to improves col­our display.
Exit
Exit the Function configuration Page
Apr 05
P.26
) shifting OSD Menu to right with value from 0 to 100;
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
G. OSD Control For Video Input Version
OSD Menu Configuration Page
OSD Menu
Language OSD H.Position OSD V.Position OSD Timer Translucent Exit
Language
Change language of OSD Menu for English or traditional Chinese
OSD H.Position
Press (" Press (!) shifting OSD Menu to left from value 0 to 100.
OSD V.Position
Press (") shifting OSD Menu to upward with value from 0 to 100; Press (!) shifting OSD Menu to downward from value 0 to 100.
OSD Timer
Enable or disable timeout of OSD Menu ONEnable OFF Disable
Translucent
Enable or disable for the diaphaneity of OSD menu YesEnable No Disable
Exit
Exit the Function configuration Page
Apr 05
P.27
AP-10AV / DP-10AV / DP-10AV Series User Manual
4. Using the System
G. OSD Control For Video Input Version
Miscellaneous Configuration Page
Miscellaneous
Mode Select
Reset Exit
Mode Select
Switch the display size for 640 x 400 or 720 x 400 in DOS mode
Reset
Enter for reloading all factory default
Exit
Exit the Function configuration Page
Loading...