3M JNPS-0135D User Manual

　製品仕様書

Product Specification

３Ｍ 印

ＭＤＲ

ノンシールドシェルストレートタイプ

キット

103XX-42X0-XXX
103XX-52X0-XXX

部品

106XX-4200-XXX
106XX-5200-XXX

3342-XX

１０６００－L0F0-X

3M Brand

MDR

JNPS-0135D

Non-Shielded Shell Straight Type

Kit
103XX-42X0-XXX
103XX-52X0-XXX

Parts
106XX-4200-XXX
106XX-5200-XXX

3342-XX

以下の改定を行う。但し、これによる仕様書の変更は実施しない。

1.新計量法試行により、単位系を SI 単位系に改定。

-( )内の数値は参考値。改定行右端に「新計量改定」と明示。

2.表紙記述の部門名変更

This specification was revised due to the requirement described below.

1. Using unit was changed to SI unit, because new measurement law came

into operation in Japan.

-( ) is reference value. “Revised by new measurement law” is describes
at right side of the revised lines.

2. Division name described in the cover page was changed.

11,Jan.,1999

SUMITOMO 3M LIMITED

TECHNICAL DEPARTMENT

ELECTRONIC & EH&P PRODUCTS DIVISION

目目目目 次次次次 ／ Table of contents

１機能 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ １

Function ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 7

２ 適合対象 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 2

Compatible Object ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8

３ 関連仕様 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 2

Related Specification Drawing ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8

４適用 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 3

Application ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 9

JNPS-0135

頁 / PAGE

D

５ 品質特性 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6

Quality Performance ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 12

６ 包装表示 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6

Package & Identify ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 12

７保管 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8

Storage ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 12

2 . COMPATIBLE OBJECT

2-1 COMPATIBLE PLUG CONNECTORS

PLUG CONNECTOR

MDR Solder Plug Connector :101XX-3000 XX
MDR Wire Mount Plug Connector :101XX-6000 XX

RECEPTACLE CONNECTOR

MDR Wire Mount Receptacle Connector :102XX-02XO XX
MDR Board Mount Receptacle Connector (Right Angle) :102XX-52XX XX
MDR Board Mount Receptacle Connector (Straight) :102XX-62XX XX
MDR Board Mount Receptacle Connector (Condominium) :10220-L8A9 VE

2-2 COMPATIBLE CABLES

Cable Overall Diameter
14P :φ7.0mm Min. , φ8.0mm Max.
20P :φ11.0mm Min. , φ12.0mm Max. ※
26P :φ11.0mm Min. , φ12.0mm Max. ※
36P :φ15.0mm Min. , φ16.0mm Max.
50P :φ15.0mm Min. , φ16.0mm Max.

JNPS-0135

D

※In 20P and 26P , if the cable (φ4 ～φ9 ) which is thinner than recommended cable

will be used , Compression Insert of 3M brand product should be used. (Refer to
JNPS-0173)

2-3 COMPATIB LE PANELS

Panel Thickness : 2.0 mm MAX. (Including with the Thickness of Washer)
However , in case of the use of the Jack Screw L26 Type in combination with the Jack
Socket Screw
(Refer to JNPS-0205) , Panel Thickness is only 1.6 mm . (Including with the Thickness of
Washer)

3 . RELATED SPECIFICATION DRAWINGS

See JNPD-0135

８