3M 61500121076, 61500121084, B1769660 User Manual

3M™ Scotch-Brite™ Products, Surface Conditioning S SFN (Discs (includes Roloc™, TN, TP, TR, TS, TSM), Sheets, Rolls, ScrimBelts

03/20/14

__________________________________________________________________________________________

Page 1 of 11

Safety Data Sheet

Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

24-8593-6

Version Number:

1.15

Issue Date:

03/20/14

Supercedes Date:

02/24/14

SECTION 1: Identification

1.1. Product identifier

3M™ Scotch-Brite™ Products, Surface Conditioning S SFN (Discs (includes Roloc™, TN, TP, TR, TS, TSM), Sheets, Rolls,
Scrim Belts

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

40% of the mixture consists of ingredients of unknown acute oral toxicity.

3M™ Scotch-Brite™ Products, Surface Conditioning S SFN (Discs (includes Roloc™, TN, TP, TR, TS, TSM), Sheets, Rolls, Scrim Belts

03/20/14

__________________________________________________________________________________________

Page 2 of 11

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

Silicon Carbide Mineral 409-21-2 30 - 45
Lubricant 68991-84-4 0.5 - 2
Titanium Dioxide 13463-67-7 0 - 0.21335
Quartz Silica 14808-60-7 0.01 - 0.12
Additive 68515-49-1 0 - 0.1
Carbon Black 1333-86-4 0 - 0.1
Poly Vinyl Chloride 9002-86-2 0.5 - 2
Cured Resin Mixture 20 - 40
Nylon Fiber Mixture 10 - 25
Nylon Scrim Mixture 5 - 10
Roloc™ TN, TP, TR, TS, or TSM Metal Attachment Mixture 0 - 5

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion

3M™ Scotch-Brite™ Products, Surface Conditioning S SFN (Discs (includes Roloc™, TN, TP, TR, TS, TSM), Sheets, Rolls, Scrim Belts

03/20/14

__________________________________________________________________________________________

Page 3 of 11

5.3. Special protective actions for fire-fighters

No unusual fire or explosion hazards are anticipated.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2. Environmental precautions

Not applicable.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged
product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks
prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or
when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust
generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source.
Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

Ingredient C.A.S. No. Agency Limit type Additional Comments

Carbon Black 1333-86-4 Amer Conf of

Gov. Indust.
Hyg.

TWA(inhalable fraction):3
mg/m3

Carbon Black 1333-86-4 Chemical

Manufacturer
Rec Guid

TWA:0.5 mg/m3

Carbon Black 1333-86-4 US Dept of

Labor - OSHA

TWA:3.5 mg/m3

Titanium Dioxide 13463-67-7 Amer Conf of

Gov. Indust.
Hyg.

TWA:10 mg/m3

Titanium Dioxide 13463-67-7 Chemical

Manufacturer
Rec Guid

TWA(as respirable dust):5
mg/m3

Titanium Dioxide 13463-67-7 US Dept of

Labor - OSHA

TWA(as total dust):15 mg/m3

Quartz Silica 14808-60-7 Amer Conf of

Gov. Indust.
Hyg.

TWA(respirable
fraction):0.025 mg/m3

3M™ Scotch-Brite™ Products, Surface Conditioning S SFN (Discs (includes Roloc™, TN, TP, TR, TS, TSM), Sheets, Rolls, Scrim Belts

03/20/14

__________________________________________________________________________________________

Page 4 of 11

Quartz Silica 14808-60-7 US Dept of

Labor - OSHA

TWA concentration(as total
dust):0.3 mg/m3;TWA
concentration(respirable):0.1
mg/m3(2.4 millions of
particles/cu. ft.)

Silicon Carbide Mineral 409-21-2 Amer Conf of

Gov. Indust.
Hyg.

TWA(as fiber):0.1
fiber/cc;TWA(inhalable
fraction):10
mg/m3;TWA(respirable
fraction):3 mg/m3

Silicon Carbide Mineral 409-21-2 US Dept of

Labor - OSHA

TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3

Additive 68515-49-1 Chemical

Manufacturer
Rec Guid

TWA:5 mg/m3

Poly Vinyl Chloride 9002-86-2 Amer Conf of

Gov. Indust.
Hyg.

TWA(respirable fraction):1
mg/m3

Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists
American Indust. Hygiene Assoc : American Industrial Hygiene Association
Chemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended Guidelines
US Dept of Labor - OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation and/or
local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control
dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Warning: Excessive
operating speed or generation of extreme heat may result in harmful emissions. Use local exhaust ventilation. Provide local
exhaust at process emission sources to control exposure near the source and to prevent the escape of dust into the work area.
Ensure that dust-handling systems (such as exhaust ducts, dust collectors, vessels, and processing equipment) are designed in
a manner to prevent the escape of dust into the work area (i.e., there is no leakage from the equipment).

8.2.2. Personal protective equipment (PPE)

Eye/face protection

To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding
operations or when near such operations. Select and use eye/face protection to prevent contact based on the results of an
exposure assessment. The following eye/face protection(s) are recommended:
Safety Glasses with side shields

Skin/hand protection

Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from grinding or
sanding.

Respiratory protection

Assess exposure concentrations of all materials involved in the work process. Consider material being abraded when
determining the appropriate respiratory protection. Select and use appropriate respirators to prevent inhalation overexposure.