3M 60650034709, 60650034683 User Manual

3M™ Abrasive Products, 747D Flap Discs 02/24/14

__________________________________________________________________________________________

Page 1 of 11

Safety Data Sheet

Copyright,2014,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

26-7366-3

Version Number:

3.02

Issue Date:

02/24/14

Supercedes Date:

03/22/13

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, 747D Flap Discs

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details
MANUFACTURER:

3M

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

Notes to Physician:

Not applicable

2.3. Hazards not otherwise classified

None.

3M™ Abrasive Products, 747D Flap Discs 02/24/14

__________________________________________________________________________________________

Page 2 of 11

58% of the mixture consists of ingredients of unknown acute oral toxicity.

74% of the mixture consists of ingredients of unknown acute inhalation toxicity.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

Ceramic Aluminum Oxide / Aluminum Oxide Mineral
Blend (non-fibrous)

1344-28-1 10 - 30

Filler 13983-17-0 0 - 10
Filler 1317-65-3 0.10 - 10
Silica 7631-86-9 0.01 - 1.2
Inorganic Fluoride 15096-52-3 2 - 7 Trade Secret *
Inorganic Fluoride 14075-53-7 2 - 10 Trade Secret *
Titanium Dioxide 13463-67-7 0.1 - 2 Trade Secret *
Filler 7727-43-7 1 - 5
Cured Resin Mixture 10 - 35
Cotton Backing Mixture 5 - 25
Fiberglass plate Mixture 20 - 25

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

3M™ Abrasive Products, 747D Flap Discs 02/24/14

__________________________________________________________________________________________

Page 3 of 11

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide During Combustion
Carbon dioxide During Combustion
Hydrogen Fluoride During Combustion

5.3. Special protective actions for fire-fighters

When fire fighting conditions are severe and total thermal decomposition of the product is possible, wear full protective
clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants,
bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2. Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Do not breathe thermal decomposition products. For industrial or professional use only. Avoid breathing of dust created by
sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check
product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when
working at sanding or grinding operations or when near such operations. Avoid release to the environment. Combustible
dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this
product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to
accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

Ingredient C.A.S. No. Agency Limit type Additional Comments

Filler 1317-65-3 US Dept of

Labor - OSHA

TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3

Aluminum, insoluble compounds 1344-28-1 Amer Conf of

Gov. Indust.
Hyg.

TWA(respirable fraction):1
mg/m3

Ceramic Aluminum Oxide /
Aluminum Oxide Mineral Blend
(non-fibrous)

1344-28-1 Chemical

Manufacturer
Rec Guid

TWA:1 fiber/cc

Ceramic Aluminum Oxide / 1344-28-1 US Dept of TWA(as total dust):15

3M™ Abrasive Products, 747D Flap Discs 02/24/14

__________________________________________________________________________________________

Page 4 of 11

Aluminum Oxide Mineral Blend
(non-fibrous)

Labor - OSHA mg/m3;TWA(respirable

fraction):5 mg/m3

Titanium Dioxide 13463-67-7 Amer Conf of

Gov. Indust.
Hyg.

TWA:10 mg/m3

Titanium Dioxide 13463-67-7 Chemical

Manufacturer
Rec Guid

TWA(as respirable dust):5
mg/m3

Titanium Dioxide 13463-67-7 US Dept of

Labor - OSHA

TWA(as total dust):15 mg/m3

Aluminum, insoluble compounds 15096-52-3 Amer Conf of

Gov. Indust.
Hyg.

TWA(respirable fraction):1
mg/m3

FLUORIDES 15096-52-3 Amer Conf of

Gov. Indust.
Hyg.

TWA(as F):2.5 mg/m3

FLUORIDES 15096-52-3 US Dept of

Labor - OSHA

TWA(as dust):2.5
mg/m3;TWA(as F):2.5 mg/m3

Silica 7631-86-9 Chemical

Manufacturer
Rec Guid

TWA(as respirable dust):3
mg/m3

SILICA, AMORPHOUS 7631-86-9 US Dept of

Labor - OSHA

TWA concentration:0.8
mg/m3;TWA:20 millions of
particles/cu. ft.

Filler 7727-43-7 Amer Conf of

Gov. Indust.
Hyg.

TWA:10 mg/m3

Filler 7727-43-7 US Dept of

Labor - OSHA

TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3

Amer Conf of Gov. Indust. Hyg. : American Conference of Governmental Industrial Hygienists
American Indust. Hygiene Assoc : American Industrial Hygiene Association
Chemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended Guidelines
US Dept of Labor - OSHA : United States Department of Labor - Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

For those situations where the material might be exposed to extreme overheating due to misuse or equipment failure, use with
appropriate local exhaust ventilation sufficient to maintain levels of thermal decomposition products below their exposure
guidelines. Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation
and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control
dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Provide local exhaust at
process emission sources to control exposure near the source and to prevent the escape of dust into the work area. Ensure that
dust-handling systems (such as exhaust ducts, dust collectors, vessels, and processing equipment) are designed in a manner to
prevent the escape of dust into the work area (i.e., there is no leakage from the equipment).

8.2.2. Personal protective equipment (PPE)

Eye/face protection

To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding
operations or when near such operations. Select and use eye/face protection to prevent contact based on the results of an