Motor Lead Pigtail Splice
for 5/8 kV Non-Shielded Cables
for 1000 Volts or less cables (heavy-duty and two-hole lug applications)
Instructions
Kit Contents (kit contains 3 splices):
3—Lug Covers
3—Locking Pins
3—Tubes Silicone Grease
3—Bag Solvent Cleaning Cloths
3—Mastic Sealing Strip(s)*
3— Strips Scotch
3—Instruction Sheet
*Quantity varies with kit number.
®
Linerless Rubber Splicing Tape 130C
Table 1
Kit Cable
Number
Feeder Motor
5316 8–4 10–4 0.30–0.51
5317 2–1/0 4–1/0 0.43–0.65
5318 1/0–250 2–250 0.53–0.88
5319 250–500 4/0–500 0.75–1.12
Size
(AWG/kcmil)
Range
Insulation
Lead O.D.
Cable
Range Length
CSA Certified for
600V or Less
Max.
in.
in.
in. 1
in. 1
Bolt
1
3
⁄
in.
⁄
2
in.
4
1
in.
⁄
4
1
⁄
in.
2
Technical Information:
• For non-shielded cables
• Rated 5/8 kV
• For cables rated 1000 Volts or less (heavy-duty and two
hole lug applications)
• Cable Size Range: Feeder: #8 AWG—500 kcmil
Motor Lead: #10 AWG—500 kcmil
• Copper Conductors
Caution
Working around energized systems may cause serious
injury or death. Installation should be performed by
personnel familiar with good safety practice in handling
electrical equipment. De-energize and ground all
electrical systems before installing product.
3M
™
Motor Lead
Pigtail Splice Kits
for 5/8 kV or less Non-Shielded Cables
5316, 5317, 5318, 5319
78-8096-4634-8-F
1.0 Prepare Cable According to Standard Procedures
1.1 Check to be sure cables fit within cable kit range as shown in Table 1 on cover.
1.2 Remove cable insulation for length recommended by terminal lug manufacturer; if no information is available, remove
fordepth of lug barrel.
2.0 Install Lugs
2.1 Install and crimp lugs per manufacturer’s direction. See back page if 3M™ Scotchlok™ Copper Lugs are used.
2.2 Clean insulation for approximately 6 using solvent saturated cloths provided in kit.
2.3 FOR 8kV ONLY. Fill lug/insulation gaps with Scotch
Figure 1
®
Scotch
Linerless Rubber Splicing Tape 130C
®
Linerless Rubber Splicing Tape130C (Figure 1).
2.4
Bolt lugs together. See Table 1 on cover for maximum bolt length. See Figure 2 for proper bolt/lug arrangement.
Figure 2
3.0 Install Lug Cover
3.1 Separate cables and apply mastic strip between and around them, 1⁄2" from ends of cable insulations (Figure 3). Build
mastic to an overall diameter that is greater than the inside diameter of the Lug Cover. Press cables together and make
certain that no void exists between them (Figure 3).
3.2 Overwrap the mastic with 1 or 2 wraps of vinyl tape (Figure 3).
Figure 3
2
78-8096-4634-8-F
3.3 FOR 8 kV ONLY. Cover the lugs and bolt with four half-lapped layers of Scotch
®
Linerless Rubber Splicing Tape130C (Figure 4).
Note: Lug cover will be printed with 5 kV rating. Mastic layer qualifies the part as 8 kV.
Figure 4
Scotch® Linerless Rubber Splicing Tape 130C
3.4 Install Lug Cover. Position Lug Cover so the punch holes are positioned between the cables (Figure 5).
Note: The kit contains a small tube of Silicone Grease. Use it to lightly lubricate the mastic and vinyl tape wraps. This
will aid in the installation of the Lug Cover.
3.5 Be sure that the punched holes are beyond the cable end of the mastic and vinyl tape wrap. Insert the plastic locking
pin through the holes (Figure 5).
Hint: Inserting the pin from the back side of the Lug Cover will aid in visually aligning the pin through both holes.
3.6 Cut off excess pin length, if desired. (Leave at least 1⁄4" extending from Lug Cover).
Figure 5
78-8096-4634-8-F
3
4.0 Tooling Index
Lug and Crimping Information for 3M™ Scotchlok™ Copper Lugs
30014 through 30045 31145 through 31166
One hole Two hole
5.0 Copper Lugs
3M™ CRIMPING TOOL-DIE SETS (NUMBER OF CRIMPS)
Cable Stud Scotchlok
™
Square D Co.
Size Size Copper Lug Burndy Corporation Thomas & Betts Corporation Anderson Div.
Number
MD6 MY29
Y34A Y35, Y39, TBM 5 TBM 8 TBM 15 VC6–3
Y45*, Y46* VC6–FT**
10 30014
6 1/4 30015 6 AWG (1) U5CRT (1) Blue (1) Blue (1) Universal (1)
5/16 30016
10 30018
3/8 30021
1/4 30022
3/8 30024
5/16 30027
5/16 30031
1/0 3/8 30032 W163 (2) 1/0 (1) A25R (1) U25RT (1) Pink (2) Pink (2) 42H (2) Universal (1)
2/0 3/8 30036 W241 (2) 2/0 (1) A26R (1) U26RT (2) Black (2) Black (2) 45 (1) Universal (1)
3/0 1/2 30041 W243 (2) 3/0 (1) A27R (1) U27RT (2) Orange (2) Orange (2) 50 (1) Universal (2)
1/2 30045 BG (3) 4/0 (1) U28RT (3) Purple (2) Purple (2) 54H (2) Universal (2)
4/0 1/2 31145 BG (4) 4/0 (2) U28RT (2) Purple (3) Purple (3) 54H (3) Universal (3)
250 1/2 31149 W166 (4) 250 (2) A29R (2) U29RT (3) Yellow (2) Yellow (2) 62 (2) Universal (2)
300 1/2 31153 A30R (2) U30RT (3) White (3) 66 (3) Universal (3)
350 1/2 31156 A31R (2) U31RT (3) Red (4) 71H (4)
400 1/2 31160 A32R (2) U32RT (3) Blue (4) 76H (4)
500 1/2 31166 A34R (2) U34RT (3) Brown (4) 87H (4)
*Y45 and Y46 accept all Y35 dies (“U” series). For Y45 use PT6515 adapter. For Y46 use PUADP adapter.
**Anderson VC6–3 and VC6–FT require no die set.
1/4 30019 W161 (1) 4 AWG (1) A4CR (1) U4CRT (1) Grey (1) Grey (1) Universal (1)
4
5/16 30023 W162 (2) 2 AWG (1) A2CR (1) U2CRT (2) Brown (1) Brown (1) 33 (1) Universal (2)
2
3/8 30028 1 AWG (1) A1CR (1) U1CRT (2) Green (1) Green (1) 37 (1) Universal (2)
1
3M, Scotch and Scotchlok are trademarks of 3M Company.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability
associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your
purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within
the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product,
regardless of the legal theory asserted.
3
Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
800-245-3573
Fax 800-245-0329
www.3M.com/electrical
Please recycle.
© 3M 2009. All rights reserved.
78-8096-4634-8-F
Loading...