WARNING: This is not a toy. Misuse may cause serious injury or death. Eye protection
designed specifically for paintball must be worn by the user and persons within range. Recommend
18 years of age or older to purchase. Persons under 18 years of age must have adult supervision.
READ OWNER’S MANUAL BEFORE USING.
Rules of Safe Marker Handling
1. Treat every marker as if it were loaded.
2. Never look down the barrel of a paintball marker.
3. Keep your finger off the trigger until ready to shoot.
Welcome . . . Thank you, for purchasing this Icon X Paintball marker. The Icon X rep-
resents the culmination of a great deal of research and development focused on
creating a marker with outstanding performance and durability at a reasonable price. The
aircraft grade aluminum upper receiver with a quick strip pin, ambidextrous cocking,
stainless steel hose, bottom line, drop forward and dual finger trigger are all features
usually available on much pricier markers or only through a great deal of after-market
expense. We believe that the affordability of a reliable, feature packed marker will
improve your playing experience.
Play hard, play safe, play to win!
ARRANTY INFORMATION
W
Standard Warranty:
The manufacturer warranties to the original customer that this product is free from
defects in material and workmanship under normal use and service for a period of 90
days from the original date of purchase by the initial owner/purchaser. The manufacturer agrees to repair or replace (at its discretion) any product within a reasonable period
of time. This warranty does not cover: o-rings, scratches, nicks, normal wear and tear of
parts, any modifications or normal fading of anodizing or damage caused by dropping or
hitting of the product. This warranty shall not apply if it is shown by the manufacturer that
the consumer caused the defect or malfunction because of misuse. This warranty only
covers original factory parts. Any modifications or tampering of original factory parts will
not be covered by this warranty. Warranty work can only be conducted by the manufacture technicians and or authorized technicians. If product needs to be repair, package it
carefully and send it together with your name, address, phone number and a brief
description of the malfunction to:
By returning the enclosed warranty registration card or registering your warranty on-line
at www.PaintballSolutions.com, within fifteen days of purchase the warranty will automatically be extended for an additional year.
Numbers shown in parentheses following part names correspond
to the numbers on the Parts key located on the centerfold pages
of this manual.
Initial
Assembly
1. Screw Barrel (23) hand tight into the Main Body (34).
2. Screw Velocity Adjuster (12) into the Rear Plug (24) approximately two complete turns.
3. Place Barrel Blocking Device on/into the end of the Barrel (24).
4. Push the safety (41) into the “safe” position (push from left to right when looking
down the sights).
Attaching Propellant Source
1. Confirm that Barrel Blocking Device is properly installed and the marker is on “Safe”.
2. Cock the marker by pulling the Bolt (28) in the rearward direction until it “clicks”
into place. This compresses the Main Spring (2) and allows the Cup Seal (7) to
properly seat.
3. Point the marker downward and in a safe direction.
4. Place the leading end of the propellant cylinder threads into the threaded interface
of the Tank Adapter (14).
5. Without pushing, twist the propellant cylinder in a clockwise direction and allow the
cylinder threads to “draw” the cylinder into the ASA. DO NOT force the cylinder
which could cause cross threading.
6. Screw the propellant cylinder completely in until it is firmly seated.
Attaching Feeder/Hopper
Due to the high rate of fire capability of this marker, we highly recommend the use of a
motorized hopper such as the Diablo TSA or Empire Reloader.
1. Confirm that Barrel Blocking Device is properly installed and the marker is on “Safe”.
2. Loosen both thumb screws on the Straight Elbow without removing them.
3. Place the smaller opening of the Straight Elbow over the top of the Vertical Feed
Tube (11) and tighten the lower thumb screw until tight.
4. Press neck of Feeder/Hopper into the top of the Straight Elbow until completely seated.
5. Orient the Feeder/Hopper so that the lid is facing the rear of the marker and the
Feeder/Hopper is parallel to the Main Body.
6. Tighten the upper thumb screw on the Straight Elbow until the Feeder/Hopper neck
is firmly held in place.
2
3
Loading Paintballs
The performance of your marker is directly related to the quality of paintballs used. We highly
recommend Diablo paintballs to give you satisfaction and success on the playing field.
1. Confirm that Barrel Blocking Device is properly installed and the marker is on “Safe”.
2. Point marker in a safe direction and load paintballs in the Feeder/Hopper. Be sure
to leave some room in the hopper for the balls to feed properly.
7. Remove the hopper/feeder from the marker.
8. Twisting the barrel in a counter-clockwise direction, remove it from the marker.
9. While pointing the paintball marker in a safe direction, push safety to the fire position.
10. Pull the trigger and allow the marker to cycle to confirm the absence of paintballs in
the marker’s breech. If a ball discharges, repeat until no more paintballs come out
of the marker.
11. Unscrew the propellant cylinder approximately one complete revolution.
Chronographing
Never operate your marker without first checking the velocity and confirming that you are
firing below that required on the field of play. At no time should the marker fire paintballs in
excess of 300 feet per second. Higher velocities are not only potentially dangerous, they often
result in a substantial increase in paintballs broken in the marker.
1. Confirm that Barrel Blocking Device is properly installed and the marker is on “Safe”.
2. Using a 5/64 hex key (not provided) make sure the Velocity Adjuster Set Screw
(12B) is backed out without removing it.
3. Make sure that you and anyone within range is wearing eye protection designed
specifically for paintball.
4. While pointing the paintball marker in a safe direction, remove the barrel blocking
device and move the safety to the fire position by pushing the safety from right to
left looking down the sights.
5. Point the marker over the chronograph and in a safe direction.
6. Pull the trigger and observe the reading on the chronograph.
7. To increase the velocity, turn the Velocity Adjuster (12) clockwise.
8. To decrease the velocity, turn the Velocity Adjuster counter-clockwise.
9. Once the desired velocity has been reached, use the 5/64 hex key (not provided) to
turn the Velocity Set Screw in until it binds against the Rear Plug. This will prevent
the velocity adjuster from moving during play and is required on most competition.
10. Re-install the Barrel Blocking Device and place the marker on “Safe”.
11. Proceed to playing field.
12. Keep the safety in the “Safe” position and barrel blocking device in place until ready
to play.
De-Gassing
1. Make sure that you and anyone within range is wearing eye protection designed
specifically for paintball.
2. Set the safety the “Safe” position.
3. Point the marker in a safe direction.
4. If you are using a motorized feeder, turn it off.
5. Twist the upper thumb screw on the straight elbow until loose.
6. Invert the marker so that the hopper/feeder is upside down so that paintballs are no
longer feeding into the marker.
WARNING: When removing the cylinder from the marker, it could fly off with enough force
to kill if the valve unscrews from the cylinder. LOOK at valve when removing cylinder. STOP if
valve starts to unscrew from the tank. Screw it back on and take it to a trained person for repair.
12. Pull the trigger until the marker fails to recock (if this takes more than 10 shots,
unscrew the cylinder an additional turn and repeat).
13. Remove (See Warning Above) the propellant cylinder.
Maintenance
WARNING: All maintenance should be performed with an unloaded and degassed marker.
Bolt & Hammer
1. De-gas the marker according to previous directions.
2. Always perform maintenance over a smooth work surface. This will help prevent the
accidental loss of small parts.
3. Make sure bolt is in the forward position before proceeding.
4. Remove the Quik Strip Pin Retainer (5A) from the Quick Strip Pin (5).
5. Remove the Quik Strip Pin.
6. Remove Hammer Plug (24) from rear of main body.
7. Pull Bolt (28) from rear. This will also remove the Spring Strut (4), Main Spring (2),
Recoil Pad (3) and Hammer (1).
8. Clean the bolt thoroughly to include rinsing in warm water if needed.
9. Lubricate the Bolt and Hammer with non-corrosive lubricant such as Empire Lube or
Empire Oil.
10. Place the Bolt’s Connecting Pin (28A) into the hole on top of the Hammer and while
pointing the marker downward guide this assembly in to the rear of the Main Body.
11. The Hammer will likely stop when it makes contact with the top of the Sear (37).
12. While putting slight pressure on the rear of the bolt, pull the trigger (this depresses
the Sear and allows the Bolt/Hammer assembly to travel forward.
13. Return the Main Spring, Recoil Pad and Spring Strut to their proper position.
14. Place the Hammer Plug into the rear of the Main Body with the longest portion over
the Main Spring/Spring Strut.
15. Push the Hammer Plug in and replace the Quik Strip Pin.
16. Replace the Quik Strip Pin Retainer.
6
7
27A
26
16
23
33
16
32
8
15A
25
18
13
11
10
34
6
7
16
22
41
35
21
9
17
40
15A
14
15
19
27
28A
16
5A
28
1
5
16
37
21
20
36
29
30
28C
2
3424
ICON X Parts List
1. Hammer
2. Main Spring
3. Recoil Pad
4. Spring Strut
5. Quick Strip Pin
A. R-Clip
6. Gas Valve
7. Cupseal
8. Valve Spring
9. Valve Gas Plug
10. Valve Stop Pin
11. Vertical Feed Neck
12. Velocity Adjuster
B. Locking Set Screw
13. Metal Ball Detent
14. Tank Adapter
15. Air Filter
A. Hose Fitting O-Ring
12
12B
16. Multi-Use O-Ring
17. Grip Frame Pin Set
18. Vertical Feed Screws
19. Bottomline Screws
20. Grip Panel Screws
21. Grip Frame Screws
22. Vertical ASA Screw
23. Barrel
24. Hammer Plug
25. Gas Line
26. Low Pressure Chamber
27. Sight Rail
A. Sight Rail Screw
28. Bolt
A. Connecting Pin
C. Connecting Pin Set
Screw
29. Drop Forward
30. Drop Forward Screws
32. Gas-Thru
33. Vertical ASA
34. Main Body
35. Grip Frame
36. Grip Panels
37. Sear
38. Sear Spring
*
40. Trigger
*Not Shown In Schematic
4
5
Storage
Always set maker on “Safe”, remove the hopper/feeder, all paintballs and propellant source
and place it in a secure location where it cannot be accessed by unauthorized persons.
Warranty Registration
To assist us in providing the best customer service possible and to increase your
warranty from 90 days to one year at no additional cost Complete and mail this to:
Trouble Shooting Guide
SymptomCauseCure
Does not FireNot CockedCock the Bolt to the rear
On “Safe”Push Safety to Fire Position
Out of GasRefill or Replace Propellant Source
Leaks air down BarrelBad Cup SealReplace Cup Seal
Not CockedCock the Bolt to the rear
Leaks air from ASA/BottleBad Bottle O-RingReplace Bottle O-Ring
Interface
Does not Re-cockLow on GasRefill or Replace
Propellant Source
Bad HammerReplace Hammer
Needs LubricationLubricate Hammer and Bolt
Debris around BoltRemove Bolt and clean
Bolt and Breach
Goes “Full Auto”Sear not catchingTighten Grip Frame