Braun 390 cc User Manual

Size:
3.58 Mb
Download

Contour Series

washable

start

stop

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

washable

start

stop

 

 

 

6

 

stop

start

5

 

11

7 8910

2

1

new

3

2

1

4

5

old

new

charge

c le a n

charge

ch a rg e

c le a n

clean

4

5

6

7

8

English

Our products are designed to meet the highest standards of quality, functionality and design. We hope you enjoy your new Gillette Shaver.

Warning

Your shaver is provided with a special cord set with an integrated Safety Extra Low Voltage power supply. Do not exchange or manipulate any part of it. Otherwise there is risk of electric shock.

reached after several charging/discharging cycles.

Re-chargingtime in the Clean&Renew™:

8hours.

Re-chargingtime with the special cord set:

1hour.

If the rechargeable batteries are discharged, you may also shave by connecting the shaver to an electrical outlet via the special cord set.

Description

1Shaver foil protection cap

2Shaver foil

3Cutter block

4Release button

5On/off switch («start/stop»)

6Long hair trimmer

7Charging light (green)

8Cleaning light (yellow)

9Replacement light for shaving parts

10Reset button

11Special cord set

Charging

The best environmental temperature for charging is between 15 °C and 35 °C.

First charge: Using the special cord set, connect the shaver to an electrical outlet with the motor switched off and charge the shaver for at least 4 hours.

The green charging light blinks when the shaver is being charged. When the battery is fully charged, the charging light lights permanently.

A full charge provides up to 50 minutes of cordless shaving time depending on your beard growth.

Once the shaver is completely charged, shave without the cord. With normal use the shaver will be charged automatically after every cleaning in the Clean&Renew™

(see separate use instructions).

Maximum battery capacity will only be

Shaving

Turn on the shaver («start»):

The pivoting cutting system automatically adjusts to every contour of your face.

Trimmer:

When the long hair trimmer is activated, it allows the controlled trimming of moustache or sideburns.

Tips for the perfect shave

We recommend that you shave before washing, as the skin tends to be slightly swollen after washing.

Hold the shaver at right angles (90°) to the skin. Stretch the skin and shave against the direction of beard growth.

To maintain 100% shaving performance, replace the shaver foil and cutter block, when the replacement light (9) comes on (after about 18 months), or when the shaving parts are worn.

Keeping your shaver in top shape

Cleaning indicator

Your shaver should be cleaned daily in the Clean&Renew™, and certainly when the yellow cleaning light (8) shines constantly after shaving. If this is not done, the yellow light will go out after some time. The shaver`s electronics will then assume it has been cleaned manually

9

and a new calculation of the time when the next cleaning is required will be started. During the cleaning process in the Clean&Renew™ the yellow light will flash and will go off after approx. 4 hours when cleaning is finished.

Automatic cleaning

Once the shaver is put into the Clean&Renew™, it is cleaned automatically (see separate instructions). Manual cleaning is recommended only when the Clean&Renew™ is not available, e.g. when travelling.

Manual cleaning

This appliance is suitable for cleaning under an open water tap.

Warning: Detach thehand-heldpart from the power supply before cleaning it in water.

Regular cleaning ensures better shaving performance. Rinsing the shaving head after each shave under running water is an easy and fast way to keep it clean:

Switch the shaver on (cordless) and rinse the shaving head under hot running water. A natural based soap may also be used provided it contains no particles or abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

Next, switch off the shaver, remove the shaver foil and the cutter block. Then leave the disassembled shaving parts to dry.

Alternatively, you may clean the shaver using the brush provided:

Switch off the shaver. Remove the shaver foil.

Using the brush, clean the cutter block and the inner area of the shaver head. However, do not clean the shaver foil with the brush as this may damage the foil.

Replacement light for shaving parts / Reset

To maintain 100% shaving performance, replace your foil and cutter block, when the replacement light for shaving parts (9) comes on (after about 18 months) or when worn.

Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil (2) and cutter block (3): 31 S)

The replacement light will remind you during the next 7 shaves to replace the shaving parts. Then the shaver will automatically reset the display.

After you have replaced the shaving parts (foil and cutter block), use a ball-pento push the reset button (10) for at least 3 seconds to reset the display manually.

While doing so, the replacement light blinks and goes off when the reset is complete. The manual reset can be done at any time.

Preserving the batteries

In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every

6 months approximately. Then recharge the shaver to full capacity. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time.

Environmental notice

This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose

of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country.

Clean&Renew™

Braun Clean&Renew™ has been developed for cleaning, charging and storing your shaver. Clean your shaver daily in the Clean&Renew™.

During the automated cleaning process,

the shaver is switched on and off at intervals to obtain best cleaning results. Since the specially formulated cleaning fluid contains a

10