Alliance Laundry Systems 35 Pound Capacity User Manual

Size:
772 Kb
Download

Drying Tumblers

25 Pound Capacity

30 Pound Capacity

35 Pound Capacity

55 Pound Capacity

Starting Serial No. 0602004144

Refer to Page 3 for Model Numbers

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

 

 

 

www.comlaundry.com

Part No. 70400001R4

 

 

 

 

 

 

August 2008

Operation/Maintenance

Installation must conform with local codes or in the absence of local codes with:

In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”

In Canada, installation must comply with StandardsCAN/CSA-B149.1or Natural Gas and Propane Code CSA C22.1, latest edition, Canadian Electric Code, Part I.

In Australia, installation must comply with the Australian Gas Association Installation Code for Gas Burning Appliances and Equipment.

WARNING

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

W033

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

W052

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W053

MISE EN GARDE

POUR VOTRE SÉCURITÉ, les informations de ce guide doivent être respectées afin de réduire les risques d’incendie, d’explosion ou d’éviter les dommages matériels, personnels ou blessures mortelles.

W033R3QU

Ne pas entreposer ou utiliser d’essence ou toutes autres vapeurs et liquides inflammables à proximité de cette machine ou de tout autre appareil.

QUE FAIRE EN CAS D’ODEUR DE GAZ :

Ne pas mettre d’appareil en marche.

Ne pas toucher aux interrupteurs électriques ; ne pas utiliser le téléphone des lieux.

Évacuer la pièce, le bâtiment ou la zone de tous les occupants.

Appeler immédiatement le fournisseur de gaz de la maison d’un voisin. Respecter les instructions communiquées par le fournisseur.

Si vous ne pouvez pas joindre le fournisseur de gaz, appeler le service d’incendie.

L’installation et l’entretien doivent être effectués par un installateur, service d’entretien qualifiés ou par le fournisseur de gaz.

W052R5QU

POUR VOTRE SÉCURITÉ

Ne pas entreposer ou utiliser d’essence ou toutes autres vapeurs et liquides inflammables à proximité de cette unité ou de tout autre appareil.

W053R2QU

IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the user smells gas. These instructions must be posted in a prominent location. Step-by-stepinstructions of the above safety information must be posted in a prominent location near the tumbler for customer use.

70400001

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

1

Table of

Contents

Introduction.........................................................................................

3

Model Identification .............................................................................

3

Customer Service..................................................................................

4

Serial Plate Location.............................................................................

4

Wiring Diagram ....................................................................................

4

Safety Information..............................................................................

5

Explanation of Safety Messages...........................................................

5

Important Safety Instructions ...............................................................

6

Operating Instructions .......................................................................

8

Emergency Stop Button on CE Models................................................

8

Operating Instructions ..........................................................................

8

Control Instructions ..............................................................................

9

Dual Digital Timer Control..............................................................

9

Single Drop Control.........................................................................

11

Preliminary Control Information .....................................................

11

Diagnostic Microprocessor Control.................................................

13

DMP Coin ........................................................................................

14

DMP OPL Models ...........................................................................

16

Ignition Control Operation ...................................................................

19

Maintenance ........................................................................................

21

Daily .....................................................................................................

21

Monthly.................................................................................................

23

Quarterly ...............................................................................................

23

Bi-Annually ..........................................................................................

23

Annually ...............................................................................................

23

Before You Call for Service ...............................................................

27

Customer Service..................................................................................

27

© Copyright 2008, Alliance Laundry Systems LLC

All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70400001

Introduction

Model Identification

Information in this manual is applicable to these models:

 

 

Gas

Steam

Electric

 

 

 

 

 

 

CHD25G2-CA025L

DR25G2-BA025N

CHD25S2-CT025S

CHD25E2-CT025E

 

CHD25G2-CA025N

DR25G2-BT025L

CHD25S2-CU025S

CHD25E2-CU025E

 

CHD25G2-CT025L

DR25G2-BT025N

DR25S2-BT025S

DR25E2-BT025E

25 Pound

CHD25G2-CT025N

DR25G2-BU025L

DR25S2-BU025S

DR25E2-BU025E

 

CHD25G2-CU025L

DR25G2-BU025N

IPD25S2-IT025S

IPD25E2-IT025E

 

CHD25G2-CU025N

IPD25G2-IT025L

 

 

 

DR25G2-BA025L

IPD25G2-IT025N

 

 

 

 

 

 

 

 

CHD30G2-CA030L

DR30G2-BT030D

CHD30S2-CT030S

CHD30E2-CT030E

 

CHD30G2-CA030N

DR30G2-BT030L

CHD30S2-CU030S

CHD30E2-CU030E

 

CHD30G2-CT030L

DR30G2-BT030N

DR30S2-BT030S

DR30E2-BT030E

30 Pound

CHD30G2-CT030N

DR30G2-BU030L

DR30S2-BU030S

DR30E2-BU030E

CHD30G2-CU030L

DR30G2-BU030N

IPD30S2-IT030S

IPD30E2-IT030E

 

 

CHD30G2-CU030N

IPD30G2-IT030L

 

 

 

DR30G2-BA030L

IPD30G2-IT030N

 

 

 

DR30G2-BA030N

 

 

 

 

 

 

 

 

 

CHD35G2-CA035L

DR35G2-BA035N

CHD35S2-CT035S

CHD35E2-CT035E

 

CHD35G2-CA035N

DR35G2-BT035L

CHD35S2-CU035S

CHD35E2-CU035E

 

CHD35G2-CT035L

DR35G2-BT035N

DR35S2-BT035S

DR35E2-BT035E

35 Pound

CHD35G2-CT035N

DR35G2-BU035L

DR35S2-BU035S

DR35E2-BU035E

 

CHD35G2-CU035L

DR35G2-BU035N

IPD35S2-IT035S

IPD35E2-IT035E

 

CHD35G2-CU035N

IPD35G2-IT035L

 

 

 

DR35G2-BA035L

IPD35G2-IT035N

 

 

 

 

 

 

 

 

CA055L

CU055L

 

CT055E

55 Pound

CA055N

CU055N

Not Applicable

CU055E

CT055L

IPD55G2-IT055L

IPD55E2-IT055E

 

 

 

CT055N

IPD55G2-IT055N

 

 

 

 

 

 

 

Includes the following control suffixes:

3O

– DX4 OPL

DO – DMP OPL

QT – dual digital timer

3V

– DX4 vended

DV – DMP vended

SD – single drop

3X

– DX4 prep for coin

DX – DMP prep for coin

SX – single drop, prep for coin

70400001

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

3

Introduction

Customer Service

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950for the name and address of the nearest authorized parts distributor.

For technical assistance, call (920) 748-3121.

Serial Plate Location

Model and serial numbers are found on serial plate on rear of machine, and inside the loading door hinge. Refer to Figure 1.

Wiring Diagram

The wiring diagram is located inside the junction or contactor box. The wiring diagram part number is in the lower portion of the electrical data on the serial plate.

1

TMB2098N

1 Serial Plate

Figure 1

4

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70400001

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

WARNING

Indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.

CAUTION

Indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property damage.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

IMPORTANT: Warranty is void unless tumbler is installed according to instructions in the Installation Manual. Compliance with minimum specifications and requirements detailed herein, and with applicable local gas fitting regulations,

municipal building codes, water supply regulations, electrical wiring regulations, and any other relevant statutory regulations. Because of varied requirements, applicable local codes should be thoroughly understood and all pre-installationwork arranged for accordingly.

WARNING

Failure to install, maintain, and/or operate this machine according to manufacturer’s instructions may result in conditions which can produce serious injury, death and/or property damage.

W051R1

NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which CANNOT be built into this tumbler. These factors MUST BE supplied by the person(s) installing, maintaining or operating the tumbler.

Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand.

70400001

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

5

Safety Information

Important Safety Instructions

Save These Instructions

WARNING

Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to working in and around AC inverter drive.

W359

1.Read all instructions before using the tumbler.

2.Refer to the GROUNDING INSTRUCTIONSfor the proper grounding of the tumbler.

3.Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.

4.Do not allow children on or in the tumbler. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

5.Before the tumbler is removed from service or discarded, remove the door to the drying compartment and the door to the lint compartment.

6.Do not reach into the tumbler if the cylinder is revolving.

7.Do not install or store the tumbler where it will be exposed to water and/or weather.

8.Do not tamper with the controls.

9.Do not repair or replace any part of the tumbler, or attempt any servicing unless specifically recommended in the user-maintenanceinstructions or in publisheduser-repairinstructions that you understand and have the skills to carry out.

10.Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

11.To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials.

12.Always clean the lint filter daily.

13.Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt.

14.The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel.

15.If not installed, operated and maintained in accordance with the manufacturer’s instructions or if there is damage to or mishandling of this product’s components, use of this product could expose you to substances in the fuel or from fuel combustion which can cause death or serious illness and which are known to the State of California to cause cancer, birth defects or other reproductive harm.

16.Tumbler will not operate with the loading door open. DO NOT bypass the door safety switch to permit the tumbler to operate with the door open. The tumbler will stop tumbling when the door is opened. Do not use the tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing or turning the START mechanism. Remove the tumbler from use and call for service.

17.Tumbler will not operate with lint panel open. DO NOT bypass lint panel safety switch to permit the tumbler to operate with the lint panel open.

18.Do not put articles soiled with vegetable or cooking oil in the tumbler, as these oils may not be removed during washing. Due to the remaining oil, the fabric may catch on fire by itself.

19.To reduce the risk of fire, DO NOT put clothes which have traces of any flammable substances such as machine oil, flammable chemicals, thinner, etc. or anything containing wax or chemicals such as in mops and cleaning cloths, or anythingdry-cleanedat home withdry-cleaningsolvent in the tumbler.

20.Use the tumbler only for its intended purpose, drying fabrics.

21.ALWAYS disconnect and lockout the electrical power to the tumbler before servicing. Disconnect power by shutting off appropriate breaker or fuse.

22.Install this tumbler according to the INSTALLATION INSTRUCTIONS. All connections for electrical power, grounding, and gas supply must comply with local codes and be made by licensed personnel when required.

6

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70400001

23.Remove laundry immediately after tumbler stops.

24.Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of reach of children at all times (preferably in a locked cabinet).

25.Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.

26.Always follow the fabric care instructions supplied by the garment manufacturer.

27.Never operate the tumbler with any guards and/or panels removed.

Safety Information

28.DO NOT operate the tumbler if it is smoking, grinding, has missing or broken parts.

29.DO NOT bypass any safety devices.

30.Solvent vapors from dry-cleaningmachines create acids when drawn through the heater of the drying unit. These acids are corrosive to the tumbler as well as to the laundry load being dried. Be suremake-upair is free of solvent vapors.

31.Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

WARNING

To reduce the risk of serious injury, install lockable door(s) to prevent public access to rear of tumblers.

W055

70400001

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

7

Operating Instructions

WARNING

To reduce the risk of fire:

DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials.

DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning cloths, or anything dry-cleanedat home with adry-cleaningsolvent.

DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.

W076

To reduce the risk of serious injury, allow cylinder to stop before cleaning lint screen.

W412

Emergency Stop Button on CE Models

All CE approved OPL tumblers are factory equipped with an emergency stop button located on the front panel. Refer to Figure 2.

1

TMB1664N

1

Emergency Stop Button

Figure 2

To operate emergency stop button:

a.Press red emergency stop button to stop all action.

b.To restart machine, pull red emergency stop button out and press START pad or button.

NOTE: Activation of the emergency stop button stops all machine control circuit functions, but DOES NOT remove all electrical power from machine.

Operating Instructions

Step 1: Clean Lint Screen/Compartment

Remove any accumulated lint from the lint screen and compartment. Close panel tightly against tumbler frame and lock panel securely, if applicable.

IMPORTANT: Clean lint screen and lint compartment daily. Failure to clean the lint screen daily will result in higher than normal temperatures that may damage laundry.

Step 2: Load Laundry

Open loading door and load cylinder with laundry. DO NOT OVERLOAD.

NOTE: Overloading causes slow drying and wrinkling.

Close loading door. Tumbler will not operate with the door open.

Step 3: Determine Control Type and Temperature Setting

Refer to the various controls, pages 9 - 18, follow instructions for the appropriate control type.

The type of fabric being dried will determine the temperature setting. Consult the fabric care label or fabric manufacturer to determine proper temperature setting.

IMPORTANT: Always follow the fabric care instructions supplied by the garment manufacturer.

Step 4: Remove Laundry

When the cycle is complete, open door and remove the laundry.

8

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70400001