Rhein Tech Laboratories, Inc. Client: Zylaya Corporation
360 Herndon Parkway Model Name: ZSEN
Suite 1400 Standards: FCC 15.247/IC RSS-210
http://www.rheintech.com
Report #: 2007146
FCC/IC ID: UVV-ZSEN/7070A-ZSEN Herndon, VA 20170
Appendix K: Manual
Please refer to the following pages.
Page 40 of 45
a
b
ZSEN001/2 Wireless Sensor
INDOOR SENSOR INSTALLATION INSTRUCTIONS
GENERAL INFORMATION
Federal Communications Commission and Industry Canada
Compliance. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules and with IC rules set in RSS-210. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. The equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and
receiver.
• Connect the equipment to an outlet on a circuit different from
that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television
technician for help.
BEFORE YOU INSTALL
Tools you will need:
• Ladder, scaffold, or personnel hoist
• Power and hand tools
- Drill, various bits - Phillips screwdriver
- Hammer - Tape measure
- Utility knife
- Indoor Installation kit (includes hardware for typical
installations)
Locate an appropriate place for the Sensor and Battery. If the
Battery will be installed above a dropped ceiling, make sure there is
just enough slack in the battery cable from the Battery location to the
Sensor location to comfortably attach and reattach the battery cable
from either end.
DO NOT affix the Sensor and Battery:
• To hot water supply pipes
• To plenums, fan-powered boxes, or similar HVAC fixtures
• Above, below or directly adjacent to lighting fixtures
• To electrical conduit (flex or rigid), free or bundled
telecommunications or security wires
• To any location that could cause mechanical interference with
the proper operation of other building safety and security
systems, i.e. sprinkler systems, etc.
DO affix the Sensor and Battery:
• To dropped ceiling support grids, support wires or structures
• To drywall, concrete, or brick walls
• Above a dropped ceiling (Battery only), to cable trays or similar
structures capable of supporting an additional 5 lbs or 2.3kg
CAUTION
CAUTION
CAUTION
CAUTION
Changes or modifications not expressly
approved by Zylaya could void the user’s
authority to operate this equipment.
This radio meets the FCC RF exposure
guidelines when used with Zylaya
accessories supplied or designated for this
product. Use of any other accessories may
not ensure compliance with these guidelines.
Use of any other transmitting devices within
20cm (8 in) of this radio could void the
user’s authority to operate this equipment.
Watch surrounding areas for electrical
hazards, lighting fixtures, plumbing
fixtures and pipes, and/or HVAC or other
environmental fixtures such as vents,
grates, or exhaust fixtures. Do not install
the Sensor or Battery within 12” of these
types of fixtures or similar machines.
NOTIFY. LOCATE. RESPOND.
3
DROP
PED
CEILING BATTERY IN
STALLATION
1
a
SOLID WALL BA
TTERY INSTALLATION
1
b
7” to 12”
Allow 7” min. from the
top of the Battery Holder
!
DROP
PED
CEILING SENSOR INSTALLATION
2
a
2
b
ATTACH THE CABLE SHROUD
Zylaya Corporation
QUESTIONS OR CONCERNS?
Zylaya Indoor Sensor Installation Manual
Lift to engage lower
1
Rotate Sensor to engage
2
1
2
Attach
3
4
SENSOR
1
Attach
Sensor).
2
3
3
Attach battery
3
SOLID WALL SEN
SOR INSTALLATION
4
4
Attach optional
5
regarding these interfaces
and connections
.
1
1
2
2
2 ½” TEMPLATE
Battery should be installed anywhere above the Sensor within the length of
the Battery Cable to a suitable location such as a dropped ceiling support:
Snap second hook
to grid support
optional cables*
and Battery Cable (right
angle to Sensor)
For installations where the Battery will be located above a
dropped ceiling, begin by removing a ceiling tile directly
adjacent to the desired mounting location of the Sensor. The
Use cable ties to
affix Battery to
mounting location
For installations where the Sensor will be affixed to a
dropped ceiling or on a wall below or adjacent to a dropped
ceiling mounted Battery:
Once the Sensor and Battery are installed and all necessary
cables are connected, attach the Cable Shroud:
Fully insert Shroud tabs
into slots in the Sensor
Hook Sensor Clip
to dropped ceiling
grid support
Snap Sensor
into clip
OR IF THE
IS WALL MOUNT…
Install anchors 2½” apart. Be
aware of the location of the
Battery- make sure the Battery
Cable can reach the Sensor.
Pivot Shroud firmly until the
Shroud is locked into place
Holder 7” to 12” below the finished ceiling height. Be sure to use the
mounting hardware that corresponds to the wall material (i.e. drywall anchors
for drywall mount, etc.)
optional
cables* and Battery
Cable (right angle to
Hang Sensor on
anchors
Product Support is available by telephone between 9:00am and 5:00pm
EST in the U.S. and Canada 301-740-3825
Product Support Tip- be prepared to provide the following information:
• Name, address, and telephone number
• The name of the Zylaya product
• Model and option (if applicable) of the Zylaya product
• Symptoms of the problem
*Additional cables are required if the Sensor is equipped with the
ZLPA001 Panic Alarm Option, the ZGWM001 Gateway Option or both.
Check the documentation for these options for additional information
For installations where the Battery cannot be installed above a
dropped ceiling or where a dropped ceiling is not available, the
Wall Mount Battery Holder must be installed. Install the Battery
to the finished ceiling!
Place anchors
2½” apart
For installations where the Battery Holder was used (Step 3b),
the Sensor can be installed onto the Battery Holder bracket:
Slide battery into
Battery Holder
upper loops with latches
cable (right angle
to Sensor), pulling
the cable through
the bottom of the
Battery Holder.
loops with tabs on
Battery Holder
2
on Battery Holder
cables*
1
*000548-1*
P/N 000548-1
444 North Frederick Avenue Suite 318
Gaithersburg, Maryland 20877
© 2007 Zylaya Corporation. All rights reserved
Loading...