Zycoo CooFone-D30, CooFone-D30P User Manual

Safety Notices

Please read the following safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device.

 Please use the external power supply that is included in the package. Other power supplies

may cause damage to the phone, affect the behavior or induce noise.

 Before using the external power supply in the package, please check power voltage.

Inaccurate power voltage may cause fire and damage.

 Please do not damage the power cord. If power cord or plug is impaired, it may cause fire or

electric shock.

 The plug-socket combination must be accessible at all times because it serves as the main

disconnecting device.

 Do not drop, knock or shake it. Rough handling will break internal circuit boards.  Do not install the device in places where there is direct sunlight. Also do not put the device

on carpets or cushions. It may cause fire or breakdown.

 Avoid exposure the phone to high temperature, below 0℃ or high humidity. Avoid wetting

the unit with any liquid.

 Do not attempt to open it. Non-expert handling of the device could damage it. Consult your

authorized dealer for help, or else it may cause fire, electric shock and breakdown.

 Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it. Wipe it with a

soft cloth that has been slightly dampened in a mild soap and water solution.

 When lightning, do not touch power plug or phone line, it may cause an electric shock.  Do not install this phone in an ill-ventilated place.  You are in a situation that could cause bodily injury. Before you work on any equipment, be

aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

Table of Content

Chapter 1 Brief Introduction to D30(P) ...................................................................... 1

1.1 Thank you for Purchasing D30(P) .................................................................................................... 1

1.2 Delivery Content ............................................................................................................................... 1

1.3 Specifications ................................................................................................................................... 2

1.4 Voice Features ................................................................................................................................. 2

1.5 Network Features ............................................................................................................................. 3

1.6 Maintenance and Management ........................................................................................................ 3

1.7 Keypad ............................................................................................................................................. 4

1.8 Port for Connecting........................................................................................................................... 4

1.9 Icon Introduction ............................................................................................................................... 5

1.10 LED Status Introduction ................................................................................................................ 5

Chapter 2 Initial Connecting and Settings ................................................................. 6

2.1 Connect the Power and Network ...................................................................................................... 6

2.1.1 Connect to Network .................................................................................................................. 6

2.1.2 Power Adapter Connection ....................................................................................................... 7

2.1.3 Basic Initialization ..................................................................................................................... 7

2.1.4 Network Settings ....................................................................................................................... 7

Chapter 3 Basic Function ........................................................................................... 9

3.1 Making a Call .................................................................................................................................... 9

3.1.1 Call Device ................................................................................................................................ 9

3.1.2 Call Methods ............................................................................................................................. 9

3.1.3 Answering a Call ....................................................................................................................... 9

3.2 DND ................................................................................................................................................ 10

3.3 Call Forward ................................................................................................................................... 10

3.4 Call Hold ......................................................................................................................................... 10

3.5 Call Waiting .................................................................................................................................... 10

3.6 Call Transfer ................................................................................................................................... 11

3.6.1 Blind Transfer .......................................................................................................................... 11

3.6.2 Attended Transfer ................................................................................................................... 11

3.6.3 Alert Transfer .......................................................................................................................... 11

3.7 Three-Way Conference Call ........................................................................................................... 11

Chapter 4 Advanced Function .................................................................................. 12

4.1 Click to Dial ..................................................................................................................................... 12

4.2 Auto Answer ................................................................................................................................... 12

4.3 Hotline ............................................................................................................................................ 12

4.4 Application ...................................................................................................................................... 12

4.4.1 SMS ........................................................................................................................................ 12

4.4.2 Memo ...................................................................................................................................... 13

4.4.3 Voice Mail ............................................................................................................................... 13

4.5 Auto Handdown .............................................................................................................................. 13

4.6 Dial Plan ......................................................................................................................................... 13

4.7 Dial Peer ......................................................................................................................................... 13

4.8 Auto Redial ..................................................................................................................................... 13

4.9 Call Completion .............................................................................................................................. 14

4.10 Power Light ................................................................................................................................. 14

4.11 Hide DTMF ................................................................................................................................. 14

4.12 Password Dial ............................................................................................................................. 14

4.13 Action URL & Active URI ............................................................................................................ 14

4.14 Push XML ................................................................................................................................... 15

Chapter 5 Basic Settings .......................................................................................... 16

5.1 Keyboard ........................................................................................................................................ 16

5.2 Screen Settings .............................................................................................................................. 16

5.3 Ring Settings .................................................................................................................................. 16

5.4 Voice Volume ................................................................................................................................. 16

5.5 Time & Date .................................................................................................................................... 16

5.6 Greeting Words .............................................................................................................................. 16

5.7 Languages ...................................................................................................................................... 17

Chapter 6 Advanced Settings ................................................................................. 18

6.1 Accounts ......................................................................................................................................... 18

6.2 Network .......................................................................................................................................... 18

6.3 Security ........................................................................................................................................... 18

6.4 Maintenance ................................................................................................................................... 18

6.5 Factory Reset ................................................................................................................................. 18

Chapter 7 Web Configuration ................................................................................. 19

7.1 Introduction of configuration ........................................................................................................... 19

7.1.1 Configuration Ways................................................................................................................. 19

7.1.2 Password Configuration .......................................................................................................... 19

7.2 Configuration via Web Browser ...................................................................................................... 19

7.3 Configuration via WEB ................................................................................................................... 20

7.3.1 BASIC ..................................................................................................................................... 20

7.3.1.1 STATUS .............................................................................................................................. 20

7.3.1.2 WIZARD .............................................................................................................................. 21

7.3.1.3 CALL LOG ........................................................................................................................... 24

7.3.1.4 LANGUAGE ........................................................................................................................ 24

7.3.2 NETWORK .............................................................................................................................. 25

7.3.3 TIME&DATE ........................................................................................................................... 32

7.3.4 VOIP ....................................................................................................................................... 33

7.3.5 PHONE ................................................................................................................................... 46

7.3.6 FUNCTION KEY ..................................................................................................................... 58

7.3.7 Maintenance ........................................................................................................................... 61

7.3.8 SECURITY .............................................................................................................................. 68

7.3.9 LOGOUT ................................................................................................................................. 74

Chapter 8 Appendix .................................................................................................... 75

Chapter 1 Brief Introduction to D30(P)

1.1 Thank you for Purchasing D30(P)

Thank you for purchasing D30(P). D30(P) is an entry level IP Phone which is designed for junior employees or middle

managers specially for promoting productivity and efficiency in daily working environment.

This IP Phone is provided with reasonable price at great quality and working performance with HD voice, friendly

user-interface and auto provisioning. And PoE is taken as another option (D30P) for users in case it’s necessary.

1.2 Delivery Content

Please check whether the delivery contains the following parts:

 The base unit with display and keypad  The handset  The handset cable  The Ethernet cable  The power supply

Attentions: The Phone may cause damage if you do not use a power adapter with D30(P). Due to different areas or

differentiated shipments, if the supplied power adapter cannot be used in your place, please consult your local

dealer.

Appearance of IP Phone description:

1.3 Specifications

Item

D30(P)

Adapter

Input: 100-240V, Output: 5V 1A

Port

WAN

10/100Base- T RJ-45 1 Port

LAN

10/100Base- T RJ-45 1 Port

Power Consumption

Idle: 2.5W, Active: 2.8W

LCD Size

128x48 pixels, 62 x 22mm

Operation Temperature

0~40℃

Relative Humidity

10~65%

CPU

Broadcom VoIP Chipset

SDRAM

128Mb

Flash

32Mb

Phone Dimension (L x W x H)

155×185×130mm

Net Weight

0.84kg

1.4 Voice Features

 Support 2 SIP servers  Support SIP 2.0 (RFC3261) and correlative RFCs  Support IAX2  Support multiple call queuing  Support IAX2 line key to call  Codec: G.711A/u, G.723.1, G.729a/b, G.722.1, G.726  Support HD voice  Echo cancellation: G.168 Compliance in LEC, additional acoustic echo cancellation(AEC) can reach 96ms max

filter length in hands-free mode

 Support Voice Gain Setting, VAD, CNG  Support full duplex hands-free  SIP support SIP domain, SIP authentication(none basic, MD5), DNS name of server, Peer to Peer/ IP call  Support DTMF type: SIP info, DTMF Relay, RFC2833  Support 9 systems ringtones and three user-defined ringtones  Soft keys programmable  SIP application: support Call forward / transfer (blind transfer / attended transfer / Ringing Transfer) / Call hold

/ call waiting / conference call / paging and intercom / call park / then grab / interpolation / Automatic Callback

/ Click call / auto secondary dial /

 Flexible call control functions: flexible dialing, support hotline number, calling reject, reject blacklist,

certification calls, white list barring, do not disturb, speakerphone automatic answer, caller ID,

anonymous calls, outgoing calls etc.

 Support phonebook 500 records, Incoming calls / outgoing calls / missed calls. Each supports 300 records.  Support SMS

 Support MWI  Support XML phonebook/browser  Support Speed dial  Support SRTP  Code synchronization via IP PBX/IMS  Support click to dial via web phone book  Voice codec setting for each SIP line  Customized LCD logo  Headset, speakerphone Ringing Selection  Ringing tone custom configuration parameters  Group listening

1.5 Network Features

 WAN/LAN: support bridge and router model  Support basic NAT and NAPT  Support PPPoE for xDSL  Support VLAN (optional: voice vlan/ data vlan)  NAT Penetrate, Stun Penetrate  Support DMZ  Support VPN (L2TP/OPEN VPN) function  Wan Port supports main DNS and secondary DNS server can select dynamically to get DNS in DHCP mode or

statically set DNS address.

 Support DHCP client on WAN  Support DHCP server on LAN  QoS with DiffServ  Network tools in telnet server: including ping, trace route, telnet client

1.6 Maintenance and Management

 Upgrade firmware through POST mode  Web ,telnet and keypad management  Management with different account right  LCD and WEB configuration can be modified into requested language, and support multi-language dynamically

shifted

 Upgrade firmware through HTTP, FTP or TFTP Telnet remote management/ upload/download setting file  Support Syslog  Support Auto Provisioning (upgrade firmware or configuration file)

1.7 Keypad

Key

Key name

Function Description

Navigation

Navigation key assist users for operating more conveniently

Redial

1. In the hook off/hands-free mode, use the key to dial the last

call number

2. In stand-by mode, it has a function to check the Outgoing Call

3. You could also find the specified contacts in phone book/call

records for quick dialing

Hands-free

Hands-free mode

Indicate Light

This light will blink when there is a missed call

Soft key 1/2/3/4

Keys combination, include functions History/ Directory/ DND/

Menu/ Del/Redial/ Send/ Quit/ Answer/ Divert/ Reject/ Hold/

Transfer/ Conf/ Close and so on

Digital Keyboard

Inputting the phone number or DTMF

1.8 Port for Connecting

Port

Name

Description

Power Switch

Input: AC 5V 1A WAN

10/100M Connect to Ethernet

LAN

10/100M Connect to PC

Headset

Port type: RJ-9 connector

1.9 Icon Introduction

Icon

Description

Call out

Call in

Call hold

Auto answer

Call mute

Contact

DND(Do not Disturb)

In hand-free mode

In hook mode

SMS

Missed call

Call forward

1.10 LED Status Introduction

Power Indication LED

LED Status

Description

Steady red

Power on

Fast Blinking red

There is an incoming call

Off

Power off

Chapter 2 Initial Connecting and Settings

2.1 Connect the Power and Network

2.1.1 Connect to Network

Notice: The following instructions will take D30 as reference, features of D30 is same as D30P. D30P supports one

more function of PoE.

Please make sure your environment is already in broadband internet during this step.

1. Broadband Router

Connect WAN port of D30 to the LAN port of broadband router to complete the network construction. In most cases,

you must configure network as DHCP mode. For detail settings, please refer to 2.1.4—Network Settings.

2. No broadband router

Connect WAN port of D30 to your LAN port of broadband modem to complete the network construction. In most

cases, if you are using a TV cable broadband, you must configure network as DHCP mode; If you use ADSL, you must

set D30 as PPPoE mode. For detail settings, please refer to 2.1.4- Network Settings.

3. Work as a broadband router

D30 supports broadband routing. When D30 is connected to WAN port of the broadband modem and your computer

or other Internet-capable device is connected to LAN port of D30, you can use the phone through Internet

broadband routing. For detail settings, please refer to 2.2.1-Network Settings.

2.1.2 Power Adapter Connection

Before connecting, please make sure your power connector matches the power outlet, meanwhile, voltage and

electric current also comply with the phone.

1. Plug power adapter to power socket.

2. Plug power adapter’s DC output to the power port of D30 to start up.

3. There will be displayed black line and “INITIALIZING” on the screen. After startup finished, phone will show

greeting, current date and time.

4. If phone has registered to the server, you can place or answer calls.

2.1.3 Basic Initialization

D30 is provided with a plenty of functions and parameters for configuration. Users should know some network and

VoIP knowledge to understand the meanings of parameters. In order to easing the use of the phone, there are basic

configurations introduced.

2.1.4 Network Settings

During network settings of the phone, please make sure that network is connected already. D30 uses DHCP to get

WAN IP, so the phone could access to network as long as DHCP is supported. If there is no DHCP server available, the

phone has to be changed to Static IP or PPPoE.

PPPoE Settings (For ADSL connection):

1. Get PPPoE account and password firstly.

2. Press Menu->Settings->Advanced Settings, then enter password, and choose network ->WAN

settings->Connection Mode, enter and choose PPPoE through navigation keys and press【Save】.

3. Press【Back】, then choose PPPoE Set, press 【Enter】.

4. The screen will show the current information. Press 【Del】 to delete it, then input your PPPoE username and

password and press 【Save】.

5. Press 【Back】 six(6) times to return to the idle screen.

6. Check the status. If the screen shows “Negotiating…” it shows that the phone is trying to access to the PPPoE

Server; if it shows an IP address, the PPPoE mode takes effective.

Static IP Settings (Static ADSL/Cable, or no PPPOE/DHCP network)

1. Prepare the network’s parameters firstly, such as IP Address, Net mask,

Default Gateway and DNS server IP address. If you don’t know this information, please contact the service provider

or technician of network.

2. Press Menu->Settings->Advanced Settings, then enter passwords, and choose Network ->WAN

settings->Connection Mode, enter and choose Static through navigation keys and press【Save】.

3. Press【Back】, then choose Static Set, press【Enter】.

4. The screen will show the current information, and then press【Del】to delete. Input your IP address, Mask,

Gateway, DNS and press【Save】to save what you input.

5. Press【Back】six(6) times to return to the idle screen.

6. Check the status, if the screen shows “Static”, the screen shows the IP address and gateway which were set just

now; if the phone could display the right time, Static IP mode takes effect.

DHCP Settings:

1. Press Menu->Settings->Advanced Settings, then enter password, and choose Network ->WAN

settings->Connection Mode, enter and choose DHCP through navigation keys and press【Save】.

2. Press【Back】six(6) times to return to the idle screen.

3. Check the status, the screen shows “DHCP”, if the screen shows the IP address and gateway which were set just

now, DHCP mode takes effect.

Chapter 3 Basic Function

3.1 Making a Call

3.1.1 Call Device

You can make a phone call via the following devices:

1. Pick up the handset,， icon will be shown in the idle screen.

2. Press the Speaker button,， icon will be shown in the idle screen.

3. Press the headset button if the headset is already connected to the Headset Port. The icon will be shown in

the idle screen. You can also dial the number firstly, and choose the method you would like to speak.

3.1.2 Call Methods

1. Speed Dial

In standby mode, enter your number to dial and press # or press Redial to make a call.

2. Hook dialing

Pick up the handset and hear dial tone, you can start dialing. After entering the destination number, press the #

key, D30 can immediately start connecting with each other. When you hear the beep ... beep ...( long beep), the

other phone started ringing, until the other party pick up the handset or use the speakerphone (time of the call

is displayed on the screen), you can start talking. When the call is completed, replace the handset hang up the

call.

3. Hands-free Dialing

Press the speakerphone key and hear a dial tone, you can start dialing. After entering the destination number,

press the # key, D30 can immediately start connecting with each other. When you hear the beep ... beep ... (long

beep), the other phone started ringing, until the other party pick up the handset or use the speakerphone when

you can start talking. When the call is finished, press the Speakerphone key to end the call.

4. Using the Redial button

If you try to call over the telephone, you can press Redial key to call an outgoing number.

Notice: if you restarted the phone, the system will clear the call log. And it’s not valid to press Redial key at this

time.

3.1.3 Answering a Call

Answering an Incoming Call

1. If User is not on another phone, lift the handset to use, or press the Speaker button/ Answer softkey to answer

using the speaker phone, or press the headset button to answer the headset.

2. If user is on another call, press the answer softkey.

During the conversation, you can alternate between Handset and Speaker phone by pressing the corresponding

buttons or picking up the handset.

3.2 DND

Press DND soft key to active DND Mode. Further incoming calls will be rejected and the display shows: icon.

Press DND softkey twice to deactivate DND mode. You can find the incoming call record in the Call History.

3.3 Call Forward

This feature allows user to forward an incoming call to another phone number. The display shows icon. The

following call forwarding events can be configured:

Off: Call forwarding is deactivated by default.

Always: Incoming calls are immediately forwarded.

Busy: Incoming calls are immediately forwarded when the phone is busy.

No Answer: Incoming calls are forwarded when the phone is not answered after a specific period.

To configure Call Forward via Phone interface:

1. Press Menu ->Features->Enter->Call Forwarding->Enter.

2. There are 4 options: Disabled, Always, Busy, and No Answer.

3. If user choose one of them (except Disabled), enter the phone number you wants to forward to receiving party.

Press Save to save the changes.

3.4 Call Hold

Press the Hold button or Hold softkey to put your active call on hold.

1. If there is only one call on hold, press the hold softkey to retrieve the call.

2. If there are more than one call on hold, press the line button, and the Up/Down button to highlight the call, then

press the Unhold button to retrieve the call.

3.5 Call Waiting

1. Press Menu ->Features ->Enter ->Call Waiting ->Enter.

2. Use the navigation keys to activate or deactivate call waiting.

3. Then press Save to save the changes.

3.6 Call Transfer

3.6.1 Blind Transfer

During talking, press key Transf, and dial the number that you want to transfer, and finish by pressing # key. The

current call will be transferred to the third party. After finishing transfer, the call you talk to will be hung up. User

cannot select SIP line when call is in transfer.

3.6.2 Attended Transfer

During the call, press key Transf, dial the number that you want to transfer to and press Send. After the third party

answers, then press Transfer to complete the transfer. (You need enable call waiting and call transfer firstly). If there

are two calls, you can just talk to one, and keep the other one on hold. The one who is kept hold cannot speak to you

or hear from you. In other way, if user wants to invite the third party during the call, they can press Conf to make

calls mode in conference mode. If user wants to stop conference, user can press Split. (User must enable call waiting

and three way call firstly).

Notice: The server that user uses must support RFC3515 or it might not be used.

3.6.3 Alert Transfer

During the call, press Transf firstly, and then press Send after inputting the number that you want to transfer. You

are waiting for connection. Now press Transf and the transfer will be done. (To use this feature, you need enable call

waiting and call transfer firstly).

3.7 Three-Way Conference Call

1. Press softkey Conf during an active call.

2. The first call is placed on hold. Then you will hear a dial tone. Dial the number to conference in, then press Send

key.

3. When the call is answered, press Conf and add the first call to the conference.

4. If you want to release the conference, press Split key.

Chapter 4 Advanced Function

4.1 Click to Dial

When user A browses on an appointed Web page, user A can click to call user B via a link (this link to user B), then

user A’s phone will ring, after A hooks off, the phone will dial to B.

Notice：It needs an external software what supports click to dial.

4.2 Auto Answer

When there is an incoming call, after a specific time, the phone will answer the call automatically.

4.3 Hotline

You can set hotline number for every sip, and then enter the dialer interface and after Warm Line Time, the phone

will call out the hotline number automatically.

4.4 Application

4.4.1 SMS

1) Press Menu ->Applications->Enter->SMS->Enter.

2) Use the navigation keys to highlight the options. You can read the message in the Inbox/Outbox.

3) After view the new message, you can press Reply to reply the message, and use the 2aB softkey to change the

Input Method, when enter the reply message, press OK, then use the navigation keys to select the line from which

you want to send, then Send.

4) If you want to write a message, you can press New and enter message. Use the 2aB softkey to change the Input

Method. When you input the message you want to send, press OK, then use the navigation keys to select the line

from which you want to send, then Send.

5) If you want to delete the message, after view the message, press Del, then you have three options to choose: Yes,

All, No.

4.4.2 Memo

You can add some memos to record some important things to remind you.

Press Menu->Application->Memo->Enter->Add.

There are some options to configure: Mode, Date, Time, text, Ring. When the configuration is completed, press Save.

4.4.3 Voice Mail

1) Press Menu->Application->Voice Mail->Enter.

2) Use the navigation keys to highlight the line which you want to set, press Edit, and use the navigation key to turn

on the mode, and then input the number. Press “2aB” softkey to choose the proper input method.

3) Press Save to save the change.

4) To view the new voicemail, Press Voicemail softkey directly. Press Dial, then you may be prompted to enter the

password, then you can listen to your new and old messages.

4.5 Auto Handdown

1. Press Menu ->Features-> Enter->Auto Handdown-> Enter.

2. Set the Mode Enable through the navigation key, then set Time, unit is minute, then press Save.

3. When the call ends, after the time that you have set, the phone will back to the idle interface.

4.6 Dial Plan

1. Press Menu ->Features-> Enter->Dial Plan-> Enter.

2. The following plans you can set: Press # to Send, Timeout to Send, Timeout, Fixed Length Number, Press # to Do

BXFER, BXFER On Onhook, AXFER On Onhook. You can enable or disable each dial plan.

4.7 Dial Peer

1. Press Menu ->Features-> Enter->Dial Peer-> Enter.

2. Press Add to enter the Edit interface, and then input number and destination. For example: Number:1,

Destination:1234, Then press Save.

3. Input 1# number in the dial interface, you can dial out 1234.

4.8 Auto Redial

1. Press Menu ->Features-> Enter->Auto Redial-> Enter.

2. Choose Mode Enabled or Disabled through the navigation key. If you choose Enable, you also need to set Interval

and Times, and then press Save.

3. After enable auto redial, calling out someone, if he/she is in busy, it will pop up a prompt box whether to auto

redial, press OK, the phone will call out him according the Interval and Times that you set.

4.9 Call Completion

1. Press Menu ->Features-> Enter->Call Completion-> Enter.

2. Enable the function through the navigation key, and then Save.

3. Call out others, if he is in busy, it will pop up a prompt Call Completion Waiting number? Press OK, when he is in

idle, it will pop up a prompt Call Completion Call number? Press OK, the phone will call out the number

automatically.

4.10 Power Light

1. Press Menu ->Features-> Enter->Power Light-> Enter.

2. Enable this function through the navigation key.

4.11 Hide DTMF

1. Press Menu ->Features-> Enter->Hide DTMF-> Enter.

2. Through the navigation key to choose: Disabled, All, Delay, Last Show. When you set up a call with others and

need to input the DTMF, the DTMF will show as you have set.

4.12 Password Dial

1. Press Menu ->Features-> Enter->Password Dial-> Enter.

2. Enable this function, you can also set Prefix and Length. For example，you want call out 1234567 and you set

Password Dial Prefix 123 and Password Length 3, then enter the dial interface and input 1234567, and then the

screen will show 123***7.

4.13 Action URL & Active URI

1. Action URL, achieve results come from a functional understanding that end a phone Action produce a URL, Action

which means the side of the phone receives incoming(Incoming call), outgoing calls(Outgoing call), turn

DND(open DND), hang up the phone(On hook), etc. To set the phone web page lists all its support of the action, each

action corresponds to a user-defined URL. When generating an action the phone is issued for the URL HTTP Get, so

as to achieve the purpose of reporting their actions.

2. Active URI，achieve results come from a functional understanding that the remote(eg PC) to send a URL to the

phone, the phone received will produce an action, such as dial , DND and so on. Enter the phone web pages

PHONE->FEATURE，enter the Active URL limit IP(such as a PC IP) Push XML

Enter the web page of the phone->PHONE->FEATURE, input Push XML Server(e.g. PC’IP), then PC can push text, SMS,

phonebook, advertisement,, execute etc. to phone to update the message or the phone makes an action.

4.14 Push XML

Enter the web page of the phone->PHONE->FEATURE, input Push XML Server(e.g. PC’IP), then PC can push text, SMS,

phonebook, advertisement,, execute etc. to phone to update the message or the phone makes an action.

Chapter 5 Basic Settings

5.1 Keyboard

1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Keyboard->Enter.

2. There are four items: DSS Key settings, Programmable Keys, Desktop Long Pressed, Soft Key , You can set up

respectively on them. Press the key Enter to the interface, then use the navigation keys to choose the function for

the key according to you want.

3. Press the key “OK” to save.

5.2 Screen Settings

1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Screen Settings->Enter.

2. You can set Contrast, Contrast Calibration and Backlight, press Enter and use the navigation keys to set, then press

the key Save.

5.3 Ring Settings

1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Ring Settings->Enter.

2. You can set Ring Volume and Ring Type, press Enter and use the navigation keys to set, then press the key Save. In

the Ring Type, the default system rings have nine and the custom ringtones have three that can be set through the

web page.

5.4 Voice Volume

1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Voice Volume->Enter.

2. Use the navigation keys to turn down or turn up the voice volume, then press the key Save.

5.5 Time & Date

1. Press Menu ->Settings->Enter->Basic Settings-> Enter->Time & Date->Enter.

2. You have two options to choose: Auto and Manual, use the navigation keys to choose, then press Save.

5.6 Greeting Words

1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Greeting Words->Enter.

2. You can enter the message and press Save, it will display in the phone screen when the phone start up.

5.7 Languages

1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Language ->Enter.

2. D30(P) supports three languages, you can use the navigation keys to choose. The default two languages are

English and Chinese.

Chapter 6 Advanced Settings

6.1 Accounts

Press Menu->Enter->Advanced settings, and then input the password to enter the interface, the default password is

123. You can set it through the web page. Then choose Account then press Enter, you can do some sip settings.

6.2 Network

Press Menu->Enter->Advanced settings, and then input the password to enter the interface. Then choose Network

and press Enter, you can do network settings, you can refer to 2.2.1 Network settings.

6.3 Security

Press Menu->Enter->Advanced settings, and then input the password to enter the interface. Then choose Security,

you can configure Menu Password, Key lock Password, Key lock Status and whether to ban Outgoing.

6.4 Maintenance

Press Menu->Enter->Advanced settings, and then input the password to enter the interface. Then choose

Maintenance and press Enter, you can configure Auto Provision, Backup, and Upgrade.

6.5 Factory Reset

Press Menu->Enter->Advanced settings, and then input the password to enter the interface. Then choose Factory Reset and press Enter, you can choose Yes or No.

Chapter 7 Web Configuration

7.1 Introduction of configuration

7.1.1 Configuration Ways

D30 has three different ways to different users.

 Use phone keypad.  Use web browser (recommendatory way).  Use telnet with CLI command.

7.1.2 Password Configuration

There are two levels to access to phone: root level and general level. User with root level can browse and set all

configuration parameters, while user with general level can set all configuration parameters except SIP (1-2) or

IAX2’s that some parameters cannot be changed, such as server address and port. User will has different access level

with different username and password.

 Default user with general level:

 Username: guest  Password: guest

 Default user with root level:

 Username: admin  Password: admin

The default password of phone screen menu is 123.

7.2 Configuration via Web Browser

When this phone and PC are connected to network, enter the IP address of the WAN port in this phone as the URL

(e.g. http://xxx.xxx.xxx.xxx/ or http://xxx.xxx.xxx.xxx:xxxx/).

If you do not know the IP address, you can look it up on the phone’s display by pressing Status button. See logon

page as below:

After you configure the IP phone, you need click【Save】button in CONFIG under Maintenance in the left catalog to

save your configuration. Otherwise the phone will lose your modification after power off and on.

7.3 Configuration via WEB

7.3.1 BASIC

7.3.1.1 STATUS

Item

Explanation

Network

Shows the configuration information on WAN and LAN port, including the connect

mode of WAN port (Static, DHCP, PPPoE), MAC address, the IP address of WAN port

and LAN port, ON or OFF of DHCP mode of LAN port and bridge mod

Accounts

Shows the phone numbers provided by the SIP LINE 1-2 servers and IAX2.

The last line shows the version number .

+ 55 hidden pages

Zycoo CooFone-D30, CooFone-D30P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual