1
RC-100 Quick Setup Guide
The RC-100 is a portable Z-Wave remote controller with multi- channel
support. It can be configured as a primary or secondary controller
within a Z-Wave home automation network. It works with almost every
Z-Wave enabled devices, binary switches, dimmers, thermostats,
secured door locks, binary or multi-level sensors. Users can control
their Z-Wave enabled devices individually or through
“Scene” control. Scene is a collection of Z-Wave devices configured to
a user-preferred settings, levels, modes or operating conditions. The
RC-100 also equipped with a backlit LCD screen and an intelligent Self
Navigated Button (SNB) system. Users can setup and operate their
Z-Wave devices through the LCD and the SNB system using their
RC-100, and enjoy a networked, wireless home automation system
anywhere at home.
RC-100 USER INTERFACE LAYOUT
Home (A1)
or
Device (A2)
Scene (A3)
Comfort (A4)
Sensor (A5)
All Off (A6)
Devices List (A2.1)
Scenes List (A3.1)
Comforts List (A4.1)
Sensors List (A5.1)
• Press c ord keys to select control category.
• Press BACK key to go back to previous page.
• Press and hold BACK key for 2 seconds to go
back to root menu.
Control
menu
2
Setup (B1)
+
Add Device (B2)
Delete Device (B3)
Add to Scene (B4)
Remove fr. Scene (B5)
Device Config. (B6)
• Press and hold ef keys simultaneously for 3
seconds to enter Setup menu.
• Press BACK key to go back to previous page.
• Press and hold BACK key for 2 seconds to go
back to root menu.
Scene Config. (B7)
Comfort Config. (B8)
Sensor Config. (B9)
Shortcut Key (B10)
Advanced Setup (B11)
System Settings (B12)
About (B13)
Select Scene (B4.1)
Device Configure (B6.1)
Sensor Configure (B9.1)
Shortcut Key (B10.1)
Learning Mode (B11.1)
Select Scene (B5.1)
Scene Configure (B7.1)
Comfort Configure (B8.1)
Config. Assoc. (B11.2)
Configuration (B11.3)
Reset to Default (B11.4)
LCD Contrast (B12.1)
B.L. Brightness (B12.2)
Sleep Timer (B12.3)
Setup
menu
3
QUICK SETUP STEPS EXAMPLE
Step 1
Connect a Z-Wave device (for example, a light switch) to power
supply.
Network Setup (C1)
+
Delete Dead Node (C4)
Listening Mode (C5)
Re-scan Devices (C3)
Create Sec. (C6)
• Press and hold cd keys simultaneously for 3
seconds to enter Network Setup menu.
• Press BACK key to go back to previous page.
• Press and hold BACK key for 2 seconds to go
back to root menu.
Create Pri. (C7)
(Create primary)
Network
Setup
menu
Rediscover N.W. (C2)
(Rediscover network)
4
Step 2
Step Setup Key LCD Indication
i)
Press and hold ef keys
simultaneously for 3
seconds under the Home
page.
⇓
ii)
Select “Add Device＂.
iii)
Press
key to add
the device into Z-Wave
network.
iv)
Press the program button
on the target device.
⇓
Home
Device >
Scene >
Comfor
t
>
OK to Enter
Setup
Add Device >
Delete Device >
Add to Scene >
OK to Enter
Add Device
Press PROG on target
>>>>
Saving Data …
Add Device
Press PROG on target
>>>>
OK
Add Device
Press PROG on target
>>>>
Setup
Add Device >
Delete Device >
Add to Scene >
OK to Enter
5
If you can’t add your Z-Wave device, this device might have been
included in another Z-Wave network. In this case, please delete this
device following the steps in the [Deleting Device fr om the Network]
section then add this device again.
Step 3
After adding devices to your RC-100, you can turn the device using
the corresponding Device Control function.
Step Setup Key LCD Indication
i)
Select “Device＂and
press key to
confirm.
A corresponding Device
Control page will be
displayed.
⇓
ii)
For on/off switches,
press f key to turn on
the device and e key to
turn off the device.
iii)
To operate dimmer and
motorized curtain:
Press and hold the
f
key until reach to your
desired level and release
the key to open the
curtain or to increase the
dimmer intensity.
Press and hold the
e
key until reach to your
desired level and release
the key to retract the
curtain or to reduce the
dimmer intensity.
Note 1: The screen will display LOCK /UNLK if this is a secured door
lock device.
Home
Device >
Scene >
Comfor
t
>
OK to Enter
Devices List
Switch 001 Off
e Off and On f
Devices List
Switch 001 Off
e Off and On f
Dimmer 002 Off
Devices List
Switch 001 Off
e Off and On f
Dimmer 002 Off
6
Note 2: You can rename your device, please refer to user manual [step
of B6 - Device Config.].
FREQUENTLY ASKED QUESTIONS
Q If my Z-Wave devices had already added into my Z-Wave gateway
(primary controller) network, what should I do for my RC-100?
How to copy my scenes se ttings to my RC-100?
A Your RC-100 can act as a secondary controller with network
information about other devices and scenes setting acquire d from your
gateway (primary control ler).
Please refer to user manual with below steps:
i) RC-100 should enter the
“
Learning Mode
＂
[step of B11.1]
(Replicating All Network and D evice Information from a Primary
Controller to your RC-100), for details please refer to RC-100
user manual.
ii) Gateway should enter the “Inclusion Mode＂to add the RC-100
into the network and replicating all network and device
information from a prim ary controller to your RC-100, please
refer to gateway user manual.
iii) Now, RC-100 will act as a secondary controller. All scenes and
device node information will transfer from gateway to RC-100,
you can On/Off the scene through RC-100 [step of A3.1].
iv) Your RC-100 will acquire scene configuration and node
information only. That means you have scene copied from
gateway but you need to include individual Z-Wave device by
RC-100 if you want to use RC-100 to control them individually.
Q Can I include all Z-Wave devices from the network by RC-100
and no need to click the PROG button for each device?
A Yes! RC-100 provides a useful f unction which is “Re-scan Devices”
that allows rediscovering all Z-Wave devices from the network.
Please refer to user manual with below steps:
i)
Assume all Z-Wave device s have been added by gateway.
ii)
RC-100 should act as a secondary controller [step of B11.1].
iii)
Execute the “Re-scan Devices” function [step of C3].
RC-100 will rediscover Z-Wave devices from the network ,
discovered devices will be re-assigned to their default categories
(Devices, Comforts and Sensors ), and names will be re-assigned
with default naming in ascending order.
- This action may take up t o 0.5-1 hour depends on how
many devices are in your network, and it will wipe out
all previously stored device names!
- Please make sure batteries are full before proceed!
iv)
Now, all Z-Wave devices will appear on the Devic e, Comfort and
Sensor categories. You can rename your device indiv idually if
needed.
Printed in China F820-8380-0000
Loading...