Z-Wave Panic Button User Manual

Z- Wa ve® P an ic Bu tt on

User’s

M

anual

I

ntroduction

The Panic Button is a wireless switch designed to control the Panic or
Scene status of other associated devices through the Z-Wave controller.
After receiving the signals emitted by the Panic Button, the Z-Wave
controller can then give commands or operate according to its own
settings. Its great compatibility with Z-Wave products makes it suitable
for smart home cloud based gateway.

The Panic Button is also a security Z-Wave device and supports the Over
The Air (OTA) feature for the product’s firmware upgrade. If you want it
to be a security device that use secure/encrypted message to
communicate in a Z-Wave network, then a security enabled Z-Wave
controller is needed.

Package C

ontents

Pani c Butto n

x 1

User Manual x 1

Command Class
Z-Wave® Panic Button Command Class Supported

COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_SUPERVISION_V1,
COMMAND_CLASS_BATTERY_V1,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_SECURITY_V1,
COMMAND_CLASS_SECURITY_2_V1,
COMMAND_CLASS_VERSION_V3,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1,
COMMAND_CLASS_POWERLEVEL_V1,
COMMAND_CLASS_NOTIFICATION_V8,
COMMAND_CLASS_CONFIGURATION_V1,

Security

COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3,
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1,
COMMAND_CLASS_POWERLEVEL_V1,
COMMAND_CLASS_NOTIFICATION_V8,
COMMAND_CLASS_CONFIGURATION_V1,
COMMAND_CLASS_BATTERY_V1,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_VERSION_V3,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Panic Button D evice Informati on

Basic Device Class: ROUTING_SLAVE
Generic Device Class: SENSOR_NOTIFICATION
Specific Device Class: NOTIFICATION_SENSOR

Detailed

descrip tion of each

comman d class

【COMMAND_CLASS_ZWAVEPLUS_INFO】
The Z-Wave Plus Info Get Command is used to get additional information of
the Z-Wave Plus device in question.
【COMMAND_CLASS_SUPERVISION】
The Supervision Command Class allows a sending node to request
application-level delivery confirmation from a receiving node. The delivery
confirmation includes relevant application-level status information in the
confirmation message. The Supervision Command Class MAY be used for
solitary commands such as Set and unsolicited Report commands.
The Supervision Command Class MUST NOT be used for session-like

command flows such as Get←→Report command exchanges or firmware

update.
【COMMAND_CLASS_BATTERY_V1】
The Battery Command Class is used to request and report battery levels for
a given device.
【COMMAND_CLASS_WAKE_UP_V2】
The Wake Up Command Class version 2 enables read back of the Wake Up
Interval capabilities in a node.
The Z-Wave Panic Button wakes up by wake up timer or presses the physical
button once, it will send Wakeup Notification Command to the node ID that
requires to be reported and stay awake for 10 seconds, if no
WAKE_UP_NO_MORE_INFORMATION command is received.
【COMMAND_CLASS_TRANSPORT_SERVICE_V2】
The Transport Service Command Class supports the transfer of datagrams
larger than the Z-Wave frame.
【COMMAND_CLASS_SECURITY_V1】
The Security Command Class create the foundation for secure application
communication between nodes in a Z-Wave network. The security layer
provides confidentiality, authentication and replay attack robustness
through AES-128.
【COMMAND_CLASS_SECURITY_2_V1】
The Security 2 Command Class is a framework for allowing nodes to
communicate securely in a Z-Wave network. The Security 2 Command Class

provides backwards compatibility to nodes implementing the Security 0
Command Class. Security 2 Command Class also defines a new
encapsulation format, new Security Classes and a new KEX Scheme 1, which
together offers a number of advantages over the Security 0 Command Class.
Security 2 Command Class is scalable and allows more KEX Schemes,
Security Classes and encapsulation formats to be introduced in the future if
necessary.
【COMMAND_CLASS_VERSION_V3】
The Version Command Class, version 3 allows supporting nodes to advertise
capabilities related to the Version Command Class and optionally provide a
detailed list of information regarding implementation on the Z-Wave chip.

【COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4】
【

COMMAND _CLASS_ASSOC IATION_V2

】

The Association Command Class is used to manage associations to NodeID
destinations. A NodeID destination may be a simple device or the Root
Device of a Multi Channel device.

【

COMMAND _CLASS_MULTI _CHANNEL_ASSOC IATION_V3

】

The Multi Channel Association Command Class is used to manage
associations to Multi Channel End Point destinations as well as to NodeID
destinations.
【COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1】
The Association Group Information (AGI) Command Class allows a node to
advertise the capabilities of each association group supported by a given
application resource. Controllers and installer tools SHOULD use AGI
information to support controller-assisted button-to-button association and
GUI-based drag-and-drop association in a plug-and-play fashion.
Centralized gateway-based deployments may create a single association
from the lifeline association group to a central management application.

Group

Name

Description

1

"Lifeline"

Lifeline group, association with 5
nodes.

2

“Basic set”

ON/OFF group, association with 5
nodes.

When the key is press and hold the button more than 1.5 seconds, a
BASIC_SET command will sent On(0xFF) or Off(0x00) to the nodes of
Grouping 2.The Basic Command Class support Version 2.
【COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2】
Manufacturer Specific Command Class, version 2 adds a set of commands to
communicate unique identification, e.g. the serial number, of the product.
Commands not mentioned here remains unchanged as specified for
Manufacturer Specific Command Class, Version 2.
【COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1】
The Device Reset Locally Command Class is used to notify central controllers
that a Z-Wave device is resetting its network specific parameters.
【COMMAND_CLASS_POWERLEVEL_V1】
The Powerlevel Command Class defines RF transmit power controlling
Commands useful when installing or testing a network. The Commands
makes it possible for supporting controllers to set/get the RF transmit power
level of a node and test specific links between nodes with a specific RF
transmit power level.
【COMMAND_CLASS_NOTIFICATION_V8】
The Notification Command Class is used to advertise events or states, such
as movement detection, door open/close or system failure. The Notification
Command Class supersedes the Alarm Command Class.

Notification Type

Notification events

0x07
(Home Security)
0x00
(Previous event clear)

0x08
(Button detected)

【COMMAND_CLASS_CONFIGURATION_V1】
The Configuration Command Class allows product specific configuration
parameters to be changed. One example could be the default dimming rate
of a light dimmer.
This class is used for setting certain vendor specific configuration variables.

ID

Name

Size

Range

Default
value

Description

1

LED Light up
Time

1

1~100,
127 127

1~100:LED light up 1 ~ 100
Seconds.
127:always on

2

Buzzer beep
times

1

0,
1~100,
127

127

0 : Disable
1~100: Sound 1~100 beeps
(0.5s on, 0.5s off)
127: Continue beep till cancel
trigger

Product Overview

LED Indicator

LED Signal

Status

OFF

No Power/paired and ready to be
triggered (with battery)

Solid Red

Device had been triggered

Red blink three times at
one blink per second

Inclusion successful/Exclusion
successful/Parameter successfully
set

Red blink two times at
one blink per second

Device had been deactivated and
back to standby mode

Red blinks at one blink

Low battery

per three seconds

Red blinks for 30
seconds at one blink per
two seconds

The device is in unpaired mode
and waiting to be inclusion

Solid Red for 5 seconds

The device is in paired mode when
insert batteries

Button Function

Function

Operation

Inclusion

Push the button three times in 1.5 seconds.
When inclusion successful, the LED will be
RED blink three times.

Exclusion

Push the button three times in 1.5 seconds.
When exclusion successful, the LED will be
RED blink three times. And the LED will be

red blinking for 30 seconds at one blink per
two seconds. The device is now waiting to
inclusion.

Reset

Push the button three times in 1.5 seconds and
hold the third push for 10 seconds till the LED
is red blinking. When reset is successful, the
device is set to factory default and now waiting
to inclusion
Please use this procedure only when the
network primary controller is missing or
otherwise inoperable.

Trigger

Push and hold the button more than 1.5
seconds.

Deactivate

When the device is triggered, push and hold the
button more than 6 seconds. The buzzer will
mute and the LED will be red blinking two
times.

Specification

Z-Wave®

Panic Button

Specification

RF Protocol

Z-Wave Plus (S2)

Power Source

DC 3V, AAA batteries x 2

Z-Wave Frequency

EU:868.42 MHz
US:916.00 MHz
JP: 922.5 MHz

Data Rate

9.6kbps /40kbps/100kbps

Operation Range

100 feet (About 30M )

LED Indicator

RED

Button

X 1
(Inclus ion/Exclusion/Trigger/Re set)

Waterproof Level

IPX4

Operation
Temperature

-10~40℃

Regulatory
Approvals

CE / FCC/TELEC / Z- Wave® Plus

Dimensions
(L*W*H)

80 x 80 x 40.5 mm

Regulatory Compliance

CE Caution

Electromagnetic compatibility and Radio spectrum Matters (ERM); Short

Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000

MHz frequency range with power levels ranging up to 500 mW; Part 2:

Harmonized EN covering essential requirements under article 3.2 of the

R&TTE Directive.

FCC Caution

This device complies with Part 15 of the FCC rules standard. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party

responsible for compliance cou ld void the authority to operate equipment.

This device and its antenna must not be c o-located or operating in

conjunction with any other antenna or transmitter. This equipment complies

with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance

20cm between the radiator & your body. This equipment has been tested

and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to p rovide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Button

LED Indicator

WEEE Information

For EU (European Union) member users: According to the WEEE (Waste

electrical and electronic equipment) Directive, d o not dispose of this product

as household waste or commercial waste. Waste electrical and electronic

equipment should be a ppropriately collected and recycled as required by

practices established for your country.

For information on recycling of t his product, please contact your local

authorities, your household waste disposal servi ce or the shop where you

purchased the product

Z-Wave Plus

This product can be included and operated in any Z-Wave network with other

Z-Wave certified devices from other manufacturers and/or other applications.

All non-battery operated nodes within the network will act as repeaters

regardless of vendor to increase reliability of the network.

This device must be used in conjunction with a Security Enabled Z-Wave

Controller in order to fully utilize all implemented functions.

This device is a security enabled Z-Wave Plus product that is able to use

encrypted Z-Wave Plus messages to communicate to other s ecurity enabled

Z-Wave Plus products. Note: A "Security Enable Z-Wave Controller" must be

used in order to fully utilize this function.

Security S2

Security S2 is supported with the Authenticated and UnAuthenticated levels

of security. The Authenticated level requires the user to enter the PIN code

or QR code printed on the box. The U nAuthenticated level does not require

the PIN code. Both security levels will encrypt nearly all communication using

AES-128 encryption to ensure reliable and secure communication.

SmartStart

SmartStart enabled products can be added into a Z-Wave network by

scanning the Z-Wave QR Code present on the product with a controller

providing SmartStart inclusion. No further action is required and the

SmartStart product will be added automat ically within 10 minutes of being

switched on in the network vicinity. The pin code is printed on the back of

device along with the QR code. Simply enter the PI N code or scan the Q R

code with a compatible device. Each QR code is unique for every device.

SmartStart uses the latest Security S2 encryption technology for all radio

communication. It is completely backwards compatible with non-SmartStart

systems if your home automation system doesn’t support it yet.

About Pin code or QR code example:

Please save the QR code or PIN code carefully.
If both the DSK representation on the product and any DSK provided in the
product packaging were to fade, rub off, or be lost, the device would not be
able to be added to a Z-Wave network.