Z-Wave Aeotec User Manual

30-09-2020 13:12

Pagina 1 van 6http://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZW112

Aeotec

Door/ Window Sensor 6

SKU: AEOEZW112

Quickstart

This is a secure Alarm Sensor for Europe. To run this device please insert fresh 1 * internal Lithium batteries. Please make sure the internal battery is fully
charged. Turn the primary controller into inclusion mode, short press the product?s Action Button that you can find in the back of the product.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,
distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this
equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and
every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not
in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave
device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of
security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Aeon Labs Door/ Window Sensor 6 is a smart Z-Wave sensor that can detect the status of door/window"s open/close in real time.
It?s a security Z-Wave device that supports security encryption. Also it supports the ?Over the Air Firmware Updating? that allows you wirelessly update its firmware if
needs.
It can be included and operated in any Z-Wave network with other Z-Wave certified devices from manufacturers and/or other applications.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this
by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use
the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Press the Action Button once that you can find in the back of the product for 20 seconds and then release. This procedure should only be used when the primary
controller is inoperable.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

30-09-2020 13:12

Pagina 2 van 6http://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZW112

Installation

Whether it?s for security or intelligence purposes, your sensor:

1. Should be affixed indoors and away from sources of moisture.

2. Placed within 30 meters of another Z-Wave device that is either a gateway or not powered by batteries.

3. The magnet and the main sensor must be less than 1.6cm apart for the small magnet installation or 2.5cm apart for the big magnet installation. Main sensor must

be affixed to the door or window and the magnet must be affixed to the frame. The magnet and the main sensor must separate when the door or window is
opened.

4. Should not be mounted on a metal frame.

Affix your Back Mounting Plate and Magnet to a surface.

The Back Mounting Plate can be affixed using screws or double-sided tape and should be mounted on the apex angle of the door. The Magnet must be affixed using
double-sided tape and can?t exceed the valid range, see the figure below.

Note:

1. There are 2 types of Magnets (Magnet 1: 30mm×6mm×2mm, Magnet 2: 30mm×10mm×2mm) , the size of magnet 2 is a little larger than magnet 1, so the

magnetism of magnet 2 is stronger than the magnet 1.

2. You can choose to install each one of magnet on the door frame according to your need or the distance between the door and frame, see the figure below.

3. The Magnets should not be around children to avoid swallowing of the magnets.

When the Back Mounting Plate is affixed by the double-sided tape, wipe the two surfaces clean of any oil or dust with a damp towel. Then when the surface has
completely dried, peel one side of the tape back and attach it to the corresponding section on the rear side of the Back Mounting Plate