SOLARCHECK MOBILCENTER P80
-Zumpe GmbH
Pumps and Sprayers
Betriebsanleitung • Operating Instructions
Notice technique • Istruzioni per l‘uso • Manual
ZUWA SOLARCHECK MOBILCENTER english
Operating Instructions
SOLARCHECK MOBILCENTER P80
1. Declaration of Conformity
The product complies with the requirements of the applicable european
directives. The conformity was declared. The documents to which the
declaration relates and the original declaration of conformity are
available at the manufacturer.
2. Introduction
Intended use
The filling unit is designed/used for filling, flushing and venting thermal solar systems
and heat pump systems.
improper. The manufacturer is not liable for any resulting damage.
Notes on the documentation
This manual provides important information for a safe and correct operation of the
solar filling unit SOLARCHECK MOBILCENTER P80.
The manual is designed for qualified personnel who are trained and specialised in
installing heating systems. Service and maintenance works must only be carried out
by approved specialists.
Subject to technical modifications
The continuous development and improvement of our products may cause minor
modifications of technical data and illustrations.
Any other use or extended use is considered to be
ZUWA SOLARCHECK MOBILCENTER english
2.1 Legends
Danger: immediate danger of death and severe injury
Danger: danger of death from electric shock
Danger: danger of scald burn
Danger of environmental and material damage
Information, note
2.2 General safety instructions
Store these instructions in such a way that they are accessible at all times for
operating personnel!
In addition to these operating instructions the following documents of related
components and of the pumping media should be applicated:
technical specifications
material safety data sheets
operating instructions
The manufacturer shall not be held liable for damage resulting from nonadherence to the operating instructions.
Danger
Danger
Danger of death due to electric shock
> Prior to work on the pump, always disconnect the drive from the
power supply.
Danger of death due to explosion
> Do not pump any liquids with a flash point of less than 55 ° C.
> Do not pump petrol or solvents.
ZUWA SOLARCHECK MOBILCENTER english
Danger of scald burn due to high media temperature
> Fill the solar system only when cold – if necessary cover the solar
Danger
collectors.
Danger of burn due to hot motor casing
> Do not block neither suction nor pressure hose more than 1 minute
to avoid overheating of the motor.
Danger of injury due to splashing liquid
Warning
Caution
> Connect the hoses tightly to the pump.
Material damage due to dry running
> Never allow the pump to run dry for more than 1 minute.
Material damage due to tilting of the cart on uneven ground
> Operate the filling unit only on even ground.
Danger of environmental damage due to hazardous pumped media
> Collect escaping pumped media and dispose of according to the
locally applicable regulations.
Material damage due to improper storage
> Prior to extended periods of pump down time clean pump to avoid
adhesions and damage to the impeller.
> Store pump under frost-protected conditions.
3. Transportation and unpacking
> After unpacking, immediately check the filling unit for completeness and damage.
> Immediately report any transit damage to the supplying company.
> Dispose of packaging material according to the respective local regulations.
ZUWA SOLARCHECK MOBILCENTER english
4. Mounting and commissioning
1. Connect pressure hose to
pump outlet
1
2
3. Connect pressure hose (1) and
return hose (2) to the fill/vent
valves and open valves
2. Connect return hose to tank
4. Fill tank and open ball valve
5. Insert cable of pump motor
into socket
6. Switch on pump
ZUWA SOLARCHECK MOBILCENTER english
7. Open tank lid to ensure the circulation
of the air.
Caution: Monitor fluid level in the tank and,
if necessary, refill heat transfer fluid to
prevent air entering the solar circuit.
8. Flush the solar circuit with the fluid.
Check at the inspection window of the
filter or through the tank opening if there
are still air bubbles in the heat transfer
fluid. Continue flushing until there is no
air remaining in the fluid.
5. End of operation
After filling and flushing the solar system
> Switch off pump.
> Close fill and vent valve at the solar station.
> Open stop valve between fill and vent valve.
The pressure that is generated between pump outlet and fill valve when flushing the
pipe can be released by opening the filter at the pump inlet. It will be easier then to
unscrew the filling hose from the fill valve.
Caution: Collect escaping pumped media in a container.
> Unscrew the filter casing and flush remaining liquid.
> Unscrew the filling hose from the fill valve.
> Unscrew return hose from vent valve.
> Screw open hose ends together with the provided connecting piece in order to
avoid dripping or escaping of fluid during transport.
ZUWA SOLARCHECK MOBILCENTER english
6. Maintenance
Danger of death due to electric shock
Danger
Caution
> Prior to work on the pump, always disconnect the drive from the
power supply.
Danger of environmental damage due to hazardous pumped media
> Collect escaping pumped media and dispose of according to the
locally applicable regulations.
6.1 Connections
> Check regularly if hose couplings are tight.
6.2 Cleaning the filter
There is a built-in fine filter on the suction side of the pump to filter out sold and
welder residues.
Check the inspection window at the filter regulraly and clean the filter when you see
dirt deposits on the strainer:
> Screw off the filter casing, remove the strainer and clean both with rinsing water
or compressed air.
7. Troubleshooting
Fault Possible cause Remedy
Pump does not take in
liquid
Pump does not build up
pressure
Suction hose between tank
and pump is not leaktight
Stop valve at the tank outlet
closed or tank empty
Filter clogged Clean the filter (see
Pressure line blocked Clean pressure hose
Stop valve at the tank outlet
closed
Filter clogged Clean the filter (see
Seal hose connection or
suction line
Open the stop valve or
fill the tank
chapter 6, maintenance)
Open stop valve
chapter 6, maintenance)
ZUWA SOLARCHECK MOBILCENTER english
8. Accessories
Four-way cock with bypass for mixing the heat transfer medium on-site
Kit for filling ground loops including two 150 litre tanks, hose extension,
additional stop valves and four-way-cock to switch the suction line from
external tanks to internal tank
Remote control with 10 metre cable
9. Technical data
SOLARCHECK MOBILCENTER P80
Voltage V 230
Frequency Hz 50
Maximum power consumption W 750
Maximum fluid temperature °C 60
Approved pumping media water, heat transfer medium
Maximum operating pressure bar 5,9
Maximum flow rate
with water / heat transfer medium
Diameter return hose / pressure hose Inch ½ / ½
Tank content L 30
Motor protection class IP 44
Dimensions (height/width/depth) mm 1000/495/555
Weight (empty tank) kg 27
L/min
35 / 31
Loading...