Page 1
WARNING：
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause
undesired operation.
1
Page 2
The following are the suggested text on SAR information
Specific Absorption Rate (SAR) information
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. This model
(FCC ID: YROG222) has also been tested against this SAR limited. The highest SAR value
reported under this standard during product certification for use at the ear is 0.713 W/kg.
There are no body worn configurations (e.g. belt-clips, holsters or similar accessories), then
body SAR is not required.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC
limits, and the shielded cables is marketed with the mobile phone, don’t use others.
GPRS Class: Class B
2
Page 3
Contents
1. Preface..................................................................................................................7
2. Quick Start............................................................................................................9
2.1 Icons Help .............................................................................................................. 9
2.2 Keys description..................................................................................................... 9
2.3 Install SIM card and battery.................................................................................. 11
2.4 Install memory card.............................................................................................. 12
2.5 Battery Charging .................................................................................................. 14
2.6 Switching on/off.................................................................................................... 15
2.6.1 Switching on................................................................................................... 15
2.6.2 Switching off................................................................................................... 15
2.7 Use shortcut keys................................................................................................. 15
3. Call functions .....................................................................................................17
3.1 Make a phone call ................................................................................................ 17
3.1.1 Dial Directly.................................................................................................... 17
3.1.2 Dial Tray......................................................................................................... 17
3.1.3 International calls ........................................................................................... 17
3.1.4 Make a call using contacts ............................................................................. 18
3.1.5 Redial the phone numberthe dialed lately ...................................................... 18
3.1.6 Dial the number with extension ...................................................................... 18
3.1.7 Emergency call .............................................................................................. 19
3.2 Answer or reject a call .......................................................................................... 19
3.2.1 Answer a call.................................................................................................. 19
3.2.2 Answer the second call .................................................................................. 19
3.2.3 Reject a call ................................................................................................... 20
3.3 The menu in communicating ................................................................................ 20
3.4 Adjust the volume ................................................................................................. 21
3.5 End a call ............................................................................................................. 21
4. Call log................................................................................................................22
4.1 Dialed numbers .................................................................................................... 22
4.2 Received calls ...................................................................................................... 23
4.3 Missed calls.......................................................................................................... 23
4.4 Rejected calls....................................................................................................... 23
4.5 Delete All.............................................................................................................. 23
4.6 Call timer.............................................................................................................. 23
4.7 Call costs (need network support)........................................................................ 24
4.8 GPRS flowrate ..................................................................................................... 24
5. Contacts..............................................................................................................25
5.1 Search contact ..................................................................................................... 25
5.2 Quick Search........................................................................................................ 27
5.3 Add new contact ................................................................................................... 28
6. Internet................................................................................................................30
6.1 URL...................................................................................................................... 30
6.2 Homepage............................................................................................................ 30
6.3 Bookmarks ........................................................................................................... 31
6.4 Histories ............................................................................................................... 31
6.5 Snapshot.............................................................................................................. 31
6.6 WAP settings........................................................................................................ 32
6.6.1 Browser settings ............................................................................................ 32
6.6.2 Prior storage medium..................................................................................... 32
3
Page 4
6.6.3 GPRS settings ............................................................................................... 33
6.6.4 Restore Default .............................................................................................. 33
7. Multimedia..........................................................................................................34
7.1 Camera ................................................................................................................ 34
7.1.1Take photos..................................................................................................... 34
7.1.2 DV .................................................................................................................. 36
7.2 Audio player ......................................................................................................... 37
7.2.1 Play audio background................................................................................... 39
7.2.2The menu of Option ........................................................................................ 39
7.3 Video Player......................................................................................................... 41
7.4 FM Radio.............................................................................................................. 42
8. Message..............................................................................................................44
8.1 Write message ..................................................................................................... 44
8.1.1 New SMS ....................................................................................................... 44
8.1.2 New MMS ...................................................................................................... 45
8.2 Inbox .................................................................................................................... 48
8.3 Outbox ................................................................................................................. 48
8.4 Draftbox................................................................................................................ 48
8.5 Sentbox................................................................................................................ 48
8.6 Message settings ................................................................................................. 48
8.6.1 Template SMS................................................................................................ 49
8.6.2 Voice mail....................................................................................................... 49
8.6.3 Cell broadcast ................................................................................................ 50
8.6.4 SMS settings.................................................................................................. 51
8.6.5 MMS settings ................................................................................................. 51
8.6.6 Message memory........................................................................................... 52
9. Tools ................................................................................................................... 53
9.1 Alarm.................................................................................................................... 53
9.2 Calendar............................................................................................................... 53
9.3 Calculator............................................................................................................. 54
9.4 Recorder ..............................................................................................................54
9.5 World time............................................................................................................ 55
9.6 STK ...................................................................................................................... 55
10. Pastime...............................................................................................................57
10.1 Picture Brower.................................................................................................... 57
10.2 EBook ................................................................................................................ 58
10.3 Boxman.............................................................................................................. 60
11. File list ................................................................................................................61
12. Settings............................................................................................................... 63
12.1 Call settings........................................................................................................ 63
12.1.1 Dual-SIM ...................................................................................................... 63
12.1.2 Network settings........................................................................................... 64
12.1.3 Divert calls ................................................................................................... 65
12.1.4 Restrict calls................................................................................................. 65
12.1.5 Call waiting................................................................................................... 66
12.1.6 Hide ID (Requires the network to support) ................................................... 67
12.1.7 Line selection ............................................................................................... 67
12.1.8 Fly mode ...................................................................................................... 67
12.1.9 Others .......................................................................................................... 67
12.2 Phone................................................................................................................. 69
4
Page 5
12.2.1 Time and date .............................................................................................. 69
12.2.2 Language ..................................................................................................... 69
12.2.3 Input modes ................................................................................................. 69
12.2.4 Set shortcut.................................................................................................. 69
12.2.5 Auto power on / off ....................................................................................... 70
12.2.6 Power management ..................................................................................... 70
12.2.7 Restore factory settings ............................................................................... 70
12.3 2D setting ........................................................................................................... 70
12.4 Display ............................................................................................................... 70
12.4.1 Wallpaper settings........................................................................................ 70
12.4.2 Standby style................................................................................................ 71
12.4.3 Set idle display............................................................................................. 71
12.4.4 Contrast ....................................................................................................... 71
12.4.5 Backlight ...................................................................................................... 71
12.4.6 Keypad light ................................................................................................. 71
12.4.7 Animation effect............................................................................................ 72
12.5 Security .............................................................................................................. 72
12.5.1 PIN ............................................................................................................... 72
12.5.2 PIN2 ............................................................................................................. 74
12.5.3 Privacy protect........................................................................................... 74
12.5.4 Auto key ....................................................................................................... 75
12.5.5 Red key locks keypad .................................................................................. 75
12.5.6 Power-on PWD ............................................................................................ 75
12.5.7 Theft proof.................................................................................................... 76
12.6 Profiles ............................................................................................................... 78
12.7 Link .................................................................................................................... 80
12.8 Torch .................................................................................................................. 82
13. Additional features ............................................................................................ 83
13.1 The function of U disk...................................................................................... 83
14. Phone maintenance...........................................................................................85
15. Eliminate the Simple Trouble............................................................................87
15.1 Phone can not switch on .................................................................................... 87
15.2 Phone be shut down automatically..................................................................... 87
15.3 PIN/PUK Lock .................................................................................................... 88
15.4 Poor quality for calling........................................................................................ 88
15.5 Can not receive calls.......................................................................................... 89
15.6 Can not make calls............................................................................................. 89
15.7 Call volume is small ........................................................................................... 89
15.8 The opposing party can not hear your voice ...................................................... 90
15.9 Phone does not ring with incoming call .............................................................. 90
15.10 Battery can not charge ..................................................................................... 90
15.11 Reveal no network............................................................................................ 91
15.12 Phone can not detect memory .........................................................................91
15.13 Storage space is not enough............................................................................ 91
15.14 The Option for PC Camera can not be achieved.............................................. 92
16. Safety Information ............................................................................................. 93
16.1 The environment for using.................................................................................. 93
16.2 Medical equipment ............................................................................................. 94
16.2.1 Pacemaker................................................................................................... 94
16.2.2 Hearing aids................................................................................................. 95
5
Page 6
16.2.3 Emergency Call............................................................................................ 95
16.3 Accessing password........................................................................................... 96
16.3.1 Password of power-on ................................................................................. 96
16.3.2 PIN ............................................................................................................ 96
16.3.3 PIN2 .......................................................................................................... 97
16.3.4 PUK ........................................................................................................... 97
16.4 Precautions for Battery Charging...................................................................... 98
16.5 Cautions for using battery................................................................................. 99
16.6 Caution of Using Accessories ......................................................................... 101
16.7 Other security imformations........................................................................... 101
6
Page 7
A
1. Preface
Respected mobile phone users, thank you for your purchase Spreadtrum
platform for mobile phones.
Using this kind of telephone will bring some surprised and pleasantly experience
to you: Support dual GSM cards and dual standby function; the function of
high-definition digital camera allows you to stay colorful memory; professional
MP3 music player; the MP4 video player brings all-round multimedia and
makes the body comfortable.
Safety Precautions
Please read the following simple rules carefully before using this mobile phone
and abide by it consciously.
If you need use mobile
Mobile phones will interfere
with the communication
phone to make or receive
network of aircraft, so
calls while driving, please
use the headset or park
please make sure the
phone is turned off or be in
your car and then use the
the flight mode during
phone.
flight.
ll wireless phones may
When you near the medical
equipment and medical
be subject to interference,
which could affect its
location where marks
phones can not be used,
performance.
please turn off your phone.
7
Page 8
In order to ensure the
best performance and
avoid damage to the
phone, please use the
original accessories and
battery and do not use
the incompatible
products.
To avoid interference with
blasting operations,
please turn off your
phone when you are in
the blast site or at the
place where the icon
posted with "turn off
two-way radio". Please
note and observe any
relevant rules or
regulations.
When your phone needs
to connect to other
devices, please read the
device's user manual to
ensure safety.
Please back up important
information stored in the
phone or keep a written
record, to prevent the
loss of important
information.
When you are in the gas
station or close to the
places where store fuel,
chemical agents or other
dangerous goods, please
turn off your phone to avoid
an explosion.
Do not burn the battery of
the phone or treat with it as
ordinary waste, with which
can avoid danger and
environmental damage.
Please observe the local
government's
environmental policies with
timely treatment and
recovery.
Some small parts (such as
memory card, etc.), should
be placed out the reach of
children, to prevent child
swallowing or other
dangerous producing.
Make sure your phone turn
on and is in the service
area, enter the emergency
number, press the call key
to inform your location.
Without permission, please
do not end the call.
8
Page 9
2. Quick Start
2.1 Icons Help
In the standby interface, the following icons may show up and their description
is as follows:
Icons Discription Icons Discription
Indicate the intensity of
network signal.
Silent mode is actived.
Long ring mode is actived.
New SMS.
Missed call.
Bluetooth is opened.
2.2 Keys description
Showing the battery
capacity.
Vibrate mode is actived.
High ring and vibrate mode
New MMS.
Alarm clock is set and
activated.
1. Number keys:
Input numbers and characters; customize number keys 1-2 as the
shortcuts of voice mail; customize number keys 3-9 as the shortcuts of
quick dial.
2. Right soft key:
9
Page 10
Execute the functions displayed in lower right corner of the screen. And
you can use it to delete the anterior letter near the cursor which you have
input in the message or exit the interface of editing when there is no letter
in the message.
3. Dial key
There are two dial key. They are used to make a phone call by SIM1 or
SIM2 and answer the telephone for SIM1 or SIM2; in standby state, adjust
the record of the Dialed calls, the Received calls and the Missed calls.
4. Hang_Up key:
It is used to refuse to the telephone; generally press this key to return to
standby state under the other condition. Press and hold this key to
open/close the mobile phone.
5. Left/Right key:
Move cursor to the left or right while editing; in standby state, press the
Left key to access [Profiles] and press the Right key to access [Write
message]; in certain submenus, press the Left key to access selected
menu and press the Right key to return to previous menu.
6. Up/Down key:
Press to browse names, telephone numbers, short messages,
submenus and so on; move cursor up or down while editing; in standby
state, press the Up key to access [Camera] and press the down key to
access [Alarm].
10
Page 11
7. OK key:
In Standby state, press it to enter the main menu or press and hold it to
open or close the torch; otherwise pressing it to access the menu you have
chosen.
8. * key:
Input special symbols; in standby state, press and hold this key to switch
among *, +, P and W.
9. # key:
Press this key to input # or switch the input methods; in standby state,
press and hold this key to switch between Silent mode and the General
profile.
10. Audio key:
It is a shortcut key to enter the audio player directly when the phone is in
the standby state.
Note: In this manual, press a key means to press the key and release;
press and hold a key means to press the key and hold for no less than
2 seconds.
2.3 Install SIM card and battery
¾ Hold down the switch key at the top of the phone about three seconds;
¾ Push down and remove the battery cover;
11
Page 12
¾ Remove the battery;
¾ Fit on the SIM1 (based on the slot with the sign of "SIM1"). When you
are installing the SIM card, please make the contact dot down (make
sure the direction of the gap on the SIM card is consistent with the slot)
and then push the SIM card inside the slot until the full match (the
installation method of SIM2 is similar to SIM1).
¾ Make the metal contact part of the battery aim at the contact pad
position and fit on it, and then install the battery cover.
Explain:
Function description in this manual is based on inserting two SIM
cards and selecting [Settings → Call setup → Dual-SIM → Standby
mode→Dual SIM dual standby]. If you only insert a single card or not
select the Dual SIM open, the interface and the Option is not the same
as the discriptions in the manual.
2.4 Install memory card
This phone supports dual T-flash cards: one is near the SIM card slots,
which is used as U disk; the other one is at the right side of the phone,
which is named memory card.
Insert the memory card and then you can put up browsing, copying and
other operations to the files on the memory card through the phone. You can
12
Page 13
expand the phone memory with the memory card.
The card which is near the SIM card slotes:
¾ Remove the back cover and battery;
¾ Make the side of Memory card which have the golden touch down, push
the card with the narrow end first into the slot until it is fully consistent
with the slot to complete the installation.
The card which is at the right side of the phone:
¾ Open the plastic cover which is marked with T-FLASH;
¾ Insert the T-flash card in the slot directly until it is fully consistent with the
slot to complete the installation (please notice the direction of the T-flash
card).
¾ Close the plastic cover.
Warning:
Do not insert or pull the memory card fast and frequently, to avoid
damage to the memory card.
13
Page 14
2.5 Battery Charging
Use the travel charger
¾ Insert the battery into the phone correctly;
¾ Open the rubber cover underneath the phone, make the side which has
arrow towards the screen, insert the charger plug into the charging
interface, and then connect the travel charger to standard power outlet.
¾ After insert the charger, the battery strength icon in upper right corner of
the screen starts scrolling that charging has begun. When the battery is
fully charged, the icon will stop scrolling and the battery symbol will
display full grid on the screen.
¾ Charging is completed, first disconnect the charger with standard
electrical outlet and then disconnect the phone and charger.
Attention:
1．Please use the standard battery and charger, or it may bring explosion.
2．If the battery is completely discharged, the battery icon should be
appeared after charging 2 to 3 minutes. Generally based on the current
state of the phone (if it is power on or be calling, etc.), the charging time is
different for 2 to 5 hours.
3．Please charge your battery through charger and avoid using the USB cable
to charge as much as possible.
14
Page 15
4．To ensure the new battery achieving the optimal performance, please
make the battery complete the battery charge and discharge cycles for
two to three times. Several initial charge for new battery, please charge
more than 10 hours continuously.
2.6 Switching on/off
2.6.1 Switching on
¾ Press the Hung_Up key about three seconds to swith on.
2.6.2 Switching off
¾ Press the Hung_Up key about three seconds to swith off.
Warning：
When you are at the place where the use of phone is prohibited or when
it may cause interference and dangerous, do not open your phone and
ensure it is not open the function of timer switch.
2.7 Use shortcut keys
In standby state, press some button directly allows you to access the
phone functions quickly, which used frequently.
Button Operation Function
15
Page 16
Number keys
of 1 to 2
Number keys
of 3 to 9
Press and hold Get into the voice mail of SIM1 or
SIM2.
Press and hold Get into the appropriate speed dial.
16
Page 17
3. Call functions
3.1 Make a phone call
3.1.1 Dial Directly
¾ In the standby state, enter the area code and the phone number.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
3.1.2 Dial Tray
¾ In the standby state, after pressing any number key, the dial interface
showed, and then you can dial directly using the keyboard.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
¾ Choose "Option" and you can carry through these functions accord to
the prompts: Add to contacts, Add to existing contact, Send SMS, Send
MMS, Insert wpn, SIM1 call, SIM2 call or make a IP call.
3.1.3 International calls
¾ Enter the country code (if the "+" is required to input when you enter the
country code, please press the “*” key twice continuously).
17
Page 18
¾ Enter the area code (usually without the preceding "0") and phone
number.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
3.1.4 Make a call using contacts
¾ Get into the Contacts to find the record you need.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
3.1.5 Redial the phone numberthe dialed lately
¾ Access the main menu to select [Call log], or press the Dial key in
standby state to view the call history and select the phone number to
call.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
3.1.6 Dial the number with extension
¾ Enter the switchboard number.
18
Page 19
¾ In the dial-up screen, select [Option → Insert wpn→ Pause P], then
enter the extension number.
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2. The extension number will be sent
out after switchboard number is dialed successfully for a few seconds.
3.1.7 Emergency call
¾ Enter the emergency number;
¾ Press the Dial key of SIM1 to make a phone call by SIM1, press the Dial key
of SIM2 to make a phone call by SIM2.
3.2 Answer or reject a call
3.2.1 Answer a call
¾ When there is a incoming call, press the Dial key of SIM1 or the Left soft
key to answer
3.2.2 Answer the second call
¾ If the phone set up the function of Call waiting, another call is incoming
19
Page 20
when you are communicating with somebody, the phone will prompte
you with, and you can deal it as follows:
Select [Maintain and Answer] or [Release and Answer] to answer the
second call after pressing the Dial key of SIM1 or the Left soft key,
and then the preceding call is set as maintain state automatically.
Press the Hung_UP key or the Right soft key to reject the second call to
continue the current call.
3.2.3 Reject a call
¾ When a call is coming, press the Hung_Up key or the Right soft key for
two times to refuse answer.
3.3 The menu in communicating
During the communication with phone, select the Menu can operate the
following actions:
¾ Turn on handfree: open or cancel the function of hands-free. During a
call, press the right soft key to choose <Handsfree> can also open /
close this function.
¾ Shuttle: maintain the current call by selecting [Shuttle]; while maintaining
a call, it can resume an active call after selecting [Shuttle] (this feature
requires the support of network).
¾ Contacts: get into the Contacts.
¾ Message: access the menu of message.
20
Page 21
¾ Call record: enter the list of call history.
¾ Start/Stop to record: record the content of communication and then
select [Menu → Stop to record] to stop the recording. At this point the
phone recording will be saved in the [Tools → Recorder → Option →
Record file list] automatically.
Attention：
Recording of the call is illegal in some countries. Therefore, when
you are recording about the call, you should seek the consent of the
other party at first.
¾ Turn on/off mute:: turn off the microphone temporarily during a call. If you
open this function, you can hear each other's voice, but the other party
can not hear your voice. Select [Unmute] can resume the call.
3.4 Adjust the volume
During a call, you can use the arrow keys "up / down key" or "Left / Right"
to adjust the volume.
3.5 End a call
When you need end the call, press the Hung_Up key to end the call.
21
Page 22
4. Call log
4.1 Dialed numbers
Display the resent records of dialed calls. Select one of them and enter
[Option]:
Option Function
Detail
Call Select SIM1or SIM2 to make a call.
Save
Send
message
Add to existing
contact
Set as rejected
number
IP call Select the type of SIM card and make an IP call for this
Delete
Delete All
SMS
MMS
Show the details about the selected record.
Store this record to SIM or phone.
Send out a message to that number.
Send out a multimedia message to that number.
Add this number to Contacts of phone.
Set the current number as refusing call, and then
you can find it after accessing [Contacts →
Blacklist].
record.
Delete this record.
Delete all the dialed records.
For the function of calling, you can go to [Settings → Call setup →
Dual-SIM] and select SIM1, SIM2 or Prompt according to your need.
22
Page 23
4.2 Received calls
Display the received calls which you have answered recently. The
operation of "Received calls" and "Dialed calls" is similar.
4.3 Missed calls
Show the recent records of missing. The operation of "Received calls"
and "Dialed calls" is similar.
4.4 Rejected calls
Refuse to accept the phone number which has been set.
4.5 Delete All
Remove all telephone records.
4.6 Call timer
Select the type of SIM card you want to view and then you can see the
related information about timer.
23
Page 24
4.7 Call costs (need network support)
¾ All costs: check the total cost for SIM1 and SIM2.
¾ Max costs: Set the max cost for SIM 1 and SIM 2, you can also edit it.
¾ Cost rate: Set the price for SIM 1 and SIM 2, you can also edit it.
¾ Cost reset: The total cost of the call will be cleared to zero.
4.8 GPRS flowrate
View the correlative information of GPRS counter.
24
Page 25
5. Contacts
The phone prepares high-capacity phone storage space carefully for you.
The capacity for storing depends on the SIM card.
5.1 Search contact
In the standby state, select [Contacts] and enter the contacts list for
viewing. Carry out searching location through the keys on the keyboard
directly (it supports fuzzy search).
# Example: search "李四"
Enter "57" can find it, for the corresponding phonetic of "李" is "l" and the
corresponding phonetic of "四" is "s".
# Example: search “sam”
The letter of "sam" is corresponded to the number key of "726", so you
just need press the "726" key to find the name.
# Example: look for names, at the beginning of which is symbol, such as";”,
“?" and so on.
Enter "1" directly to look for it.
After entering the Contacts, it shows the list of all contacts. Press the Left
and Right keys to switch among the various groups.
25
Page 26
Option Function
Show all contacts in SIM1, SIM2 and in the
All
phone.
Unclassed
group Show the contacts of " Unclassed group ".
SIM1
SIM2
Show all contacts stored in SIM1.
Show all contacts stored in SIM2.
Show all contacts whose group set as
Family
"Family".
Show all contacts whose group set as
图标
Friends
Colleagues
Classmates
Blacklist
Other 1
"Friends".
Show all contacts whose group set as "
Colleagues ".
Show all contacts whose group set as
"Classmate ".
Show all contacts which have set as
rejecting number.
Show all contacts whose group set as
"Other 1".
Show all contacts whose group set as
Other 2
"Other 2".
Other 3 Show all contacts whose group set as
26
Page 27
"Other 3".
The order of contact is in accordance with unnamed, special symbols,
numbers, letters (if it is Chinese name, you can select the names by the
corresponding Chinese phonetic alphabet).
5.2 Quick Search
In the standby state, select [Contacts] and enter the contacts list for
viewing. Carry out searching location through the keys on the keyboard
directly (it supports fuzzy search).
# Example: search "李四"
Enter "57" can find it, for the corresponding phonetic of "李" is "l" and the
corresponding phonetic of "四" is "s".
# Example: search “sam”
The letter of "sam" is corresponded to the number key of "726", so you
just need press the "726" key to find the name.
# Example: look for names, at the beginning of which is ";”, “?".
Enter "1" directly to look for it.
Select the record you have selected and enter [Option]:
Option Function
New Create information for new contact.
Contacts search
Find the details of the required number.
Write message Edit and sent SMS or MMS to the current number.
27
Page 28
Dial up
Send vCard
Delete Delete the current record.
Mark
Copy Copy the record to SIM1 (SIM2), U disk or memory card.
Others
Speed dial
setting
Own
number
Memery
query
Call the current number. You can select dial directly or make
an IP dial.
Sent this record via SMS or Bluetooth.
Mark the current record or mark all the records.
Add this number to the list of speed dial. After setting the
function of speed dial, press one of the keys from 3 to 9
in standby state and then you can dial the speed dial
number corresponding to the number key directly.
Set the current number as my phone numbers. Whether
support the function and the number of storage depends
on your SIM card.
Query the memory state of Contacts for SIM1, SIM2 and
phone.
Single /
double line
Recorded information can be displayed in one-line or
two-line.
display
When the members of groups (except "All", "SIM1", "SIM2") is not empty,
it can also offer [Transfer], [Rename] and other operations by pressing
[Option].
5.3 Add new contact
¾ Phone: all records stored in phone except contacts stored in SIM1
and SIM2. You can select the corresponding group and set more
than one number. This feature allows you to input your name, phone
28
Page 29
number, home phone, business phone and so on. You can choose
caller picture and caller ring tone for the current contact.
¾ SIM1 / SIM2: add contacts to the SIM1 or SIM2 and it can store only
one number to each name.
Note:
The name of new contact can be empty but the number of it can not
be empty.
29
Page 30
6. Internet
The Internet is the application platform which combines the wireless
communications and Internet and it enables you to get rich application by
phone, such as Internet information resources and e-commerce.
In the standby state, press the middle key to enter the main menu and
them select "Internet."
Notice:
1．Your Internet service provider may not support some functions, so
please make sure your SIM card can support and have opened the
Internet feature in order to ensure the normal operation of the browser.
2．If you browse the web, you need to charge fees related to traffic.
6.1 URL
Input the web site you need to browse.
China's largest free wireless Internet portal lets you know the world
without leaving home.
6.2 Homepage
Select this to connect the pre-set homepage or the default homepage
30
Page 31
directly.
6.3 Bookmarks
The bookmark is blank as default and you are free to edit it. Commonly
used website can be saved in the bookmarks with a simple name tag.
Select one of the bookmarks and then you can connect to the current web
site directly. The setting operation is as follows:
Add bookmark: Select it, input the address and name for the bookmark
and then select save.
6.4 Histories
Record the web sites you have visited previously.
6.5 Snapshot
Enter it and you can browse a snapshot which you have saved in.
31
Page 32
6.6 WAP settings
6.6.1 Browser settings
¾ Clear cache: In order to avoid congestion and improve the speed of web
browsing, please clear the cache periodically.
¾ Network account SIM1/SIM2: Select the accout for SIM1 or SIM2.
¾ Image download: activate the feature and then the image of the
download page can display.
¾ Play background sound: start it and then you can play the background
music.
¾ Accept pushmsg: you can receive Push messages after activating the
feature.
Notice: Do not change the settings, or it may not visit the website
normally.
6.6.2 Prior storage medium
You can choose the priority position for picture browser, music and
images.
32
Page 33
6.6.3 GPRS settings
Set the GPRS is always opened or opened when necessary.
6.6.4 Restore Default
WAP settings can be restored to the initial state.
In the interface of browsing the web, make the focus switch among the
address bar, web and tool bar by pressing the "left soft key".
Use the toolbar:
The icon shows the following table when you are browsing the web:
Icons Funtion
Home: Return to homepage.
Refresh: Update the page content or close it.
/
Back: According to the history, visit a website after
the current page.
Forward: According to the history, visit a website on
the current page.
Bookmark: save the current URL in bookmark.
Add Homepage: Set the current web as homepage.
Recent pages: View the history of web viewing.
Save the file: You can save snapshot, save picture or
save the sound.
Quit: choose it to exit the browser.
33
Page 34
7. Multimedia
7.1 Camera
Get into the Multimedia, select [Multimedia → camera] to enter the
camera interface.
7.1.1Take photos
In the camera interface, use the up and down keys to adjust the focal
length; use the left and right key to enter the [shooting Settings]; use the
middle key to take pictures.
In the [shoot mode] under the menu of [shooting Settings], select [DC
mode] to begin to find the view.
¾ Camera settings
In the camera interface of finding the view, use the left and right key to
enter the Option of [shooting settings] to set:
Shoot mode: You can switch between DC mode and DV mode
directly.
Size: Set photo’s resolution is 1280x960, 640x480, 320x240 or 176
x220.
Profiles: Switch the mode between normal mode and night mode.
Brightness: Use the up and down keys to set the brightness effect.
Contrast: Use the up and down keys to set the contrast effect.
34
Page 35
Exposure bias: Use the up and down keys to set the exposure
compensation effect.
Frame: You can choose No frame or Frame1.
Cont. shot: Set the continuous shot mode.
White balance: Select Auto, Incandescence, Fluorescent, Daylight or
Cloud.
Delay: You can set the timer as disabled, 3s or 10s. After setting the
delay time, the camera interface will appear the countdown in the
preview screen after pressing the middle button to take photos. After
a set time, the phone will take photographs automatically.
Special effects: You can set the effect as normal, black and white,
red, green, blue, yellow, negative or sepia effect.
¾ Option:
In the photo viewing interface, use the left soft key to enter [Option]:
Gallery: Access to view images.
Settings:
Quality: Select high, normal or simple according to your need.
Banding: You can set it as 50HZ or 60HZ.
Shutter sound: Open or close the effect of shutter sound.
Auto Save: Open this setting, the system will save the photos you
have taken automatically; otherwise, you need to press the
confirm key to save the current photo.
Display parameters: Open it, the upper left corner of the preview
interface for taking pictures will show the photographs
parameters.
35
Page 36
Storage: Set the storage location for the current photo.
Help: Provide the help information.
7.1.2 DV
In the [shoot mode] under the menu of [shooting Settings], select [switch
to shoot] to begin to find the view for filming.
¾ shooting settings
In the interface of camera viewfinder, use the left and right keys to enter
the [shooting settings] to set:
Shoot mode: You can switch between DC mode and DV mode
directly.
Size: Set photo’s resolution is 320x240, 176x144, 160x128 or 128
x96.
Brightness: Use the up and down keys to set the brightness effect.
Contrast: Use the up and down keys to set the contrast effect.
Effect: You can set the effect as normal, black and white, red, green,
blue, yellow, negative or nostalgic effect.
¾ Option
In the camera viewfinder interface, use the left soft key to enter [Option]:
View: Get into the list of video files.
Settings：
Banding: You can set it as 50HZ or 60HZ.
Audio: It can be turned on or off, in order to take audio video or
silent vedio.
36
Page 37
Type: Set the video files as AVI or 3GP according to your need.
Display parameters: Open it, the upper left corner of the preview
interface for shooting will show the parameters of shooting.
Storage: Set the storage location for the current photo.
Help: Provide the help information.
Description:
If you are shooting, there are calls, MMS, alarm clock and other
information coming, the current shooting video will be saved automatically.
7.2 Audio player
The phone can play your stored music files and the downloaded ring
tones by audio player; it supports the function of background play.
Description:
The Audio player supports MPEG 1 layer 3 audio, MPEG 2 layer 3 low
sampling rate extension and MPEG 2.5 layer 3 (unofficial).
In the standby state, press the middle button to access main menu; select
[Multimedia → audio player] to get into the audio player interface.
The icons’ description in the play interface of Audio Player:
Icons Description
/
Switch between play and pause.
37
Page 38
/
/
Select them to go to the upper song or the next song.
Stop playing.
No Lyrics
Display the lyrics. The suffix Lyrics is lrc, lyrics and files
must have the same name and they are placed in the
same directory, then the lyrics can be displayed.
Display lyrics when the screen is in the state of always
lighting.
Plus or minus the volume. Press the * key and the #
key to adjust the volume.
The progress bar shows the progress of music playing.
EQ settings (normal, classical, concert halls, jazz,
rock, soft rock)
/
/
Set the start point for the function of repeating.
Set the end point for the function of repeating.
Play songs integrallty.
Open random playing mode or the order playing mode.
Loop or prohibit loop.
Instructions for the interface of audio player: The implementation for all
the functions is pressing the OK key after selecting the function you need
by the up key, the down key, the left key or the right key, except the volume
adjustment.
When the song is playing in the audio player interface or in the
38
Page 39
background playing mode, these keys which are just under the phone
screen can be used to bring convenience to you: please press the
key to play the upper song; press the
the
key to make the audio player in the pause state or playing state
when the phone is in the audio player interface, press the
key to play the next song; press
key to enter
the audio player directly when the audio player is in the background playing
mode; press the
key to let the audio player stop.
7.2.1 Play audio background
In the playing state of the audio playback mode, press the Hung_Up key
to exit playback interface and then the audio player enter the background
playing mode with the idle screen which shows the name of the music.
7.2.2The menu of Option
Get into the audio player screen and press the [Option] to open the action
menus.
¾ Open: Open the corresponding music file in the memory card.
¾ Current playing list: Display the currently playing track.
Enter the "Cuttent playing List" screen; press [Option] to open the action
menus:
Play: Play the selected audio file.
39
Page 40
Add music: The audio in the memory card can be added to
playlist.
Delete from list: The selected audio file will be removed from the
current playlist.
Save list: Save all the songs under the current in the list with the
custom name, then you can press [Playlist] to find the playlist
name you have saved.
Clear current play list: Clear all the audio files in the current list.
¾ All play lists: Show all of playlists. The "All music" is a fixed list and
you can not delete, rename or copy it.
Get into "All music" or other list interface, press [Option] to carry
out these operations: play, browse, delete list, new list, rename, copy,
and update the entire track.
¾ Set ring: The music which is playing is set to "call ring" or "alarm
ring".
¾ Add to list: You can create a new list in the playing music file, and
add it to the playlist.
¾ Add music mark：The selected audio file is set to music bookmarks
then it will be stored to the [music Bookmarks] automatically.
¾ Music mark: You can check all the audio files which are set as
bookmarks.
40
Page 41
¾ EQ setting: EQ settings can be set and it is divided into "General",
"Classical", "Concert", "Jazz", "Rock" and "soft rock."
7.3 Video Player
Video player supports files with the format of 3GP, MP4 or AVI. If the
document is non-standard format, the conversion tool is required to convert
these files into standard format.
Access the main menu and select [Multimedia → Video Player].
Icons description in the playing interface of video player:
icons Icons Help
/
/
/
Play / Pause
Fast forward / rewind
Stop playing
Plus / minus player’s volume, press * / # sign key to adjust the
volume size.
Display the details of the video files.
Play all files in the file list continuously.
Play the current file only.
Full Screen Playing.
Instructions of the video player interface: In addition to volume adjustment,
implementation for other functions is "use the up/down keys and the
right/left key to select, and then press the middle button".
41
Page 42
Enter the video player screen, press [List → Option] to open the action
menu.
¾ Play: Play video file at the cursor.
¾ Add video item: Select the video files from the U disk or memory card to
add to the playlist.
¾ Update list: Refresh the current playlist.
¾ Delete from list: The selected video file is deleted from the playlist.
¾ Detail: View the details of the music files.
¾ Power on animation: The selected video is set as starting animation.
¾ Power off animation: The selected video is set as shutdown animation.
¾ Mark: The selected video files will be marked.
7.4 FM Radio
In the standby state, press the middle button to access the main menu to
enter [Multimedia →FM Radio] after insert or not insert the headset.
Description of Icons in the FM Radio Interface:
Icon Operation Instruction
Showing
Headphone is used to listen to the FM radio.
/
Showing
Showing
Broadcast the radio by loudspeaker.
The scroll bar of frequency.
The right/left
key
Adjust the frequency of the radio to the right or
left.
42
Page 43
/
The */# key
Showing
Display the volume of the radio.
Adjust the volume size.
In the "FM Radio" interface, click [Option] to enter the following menus:
¾ Auto search and save: Search all the radio channels automatically and
save them to the "Channel list" automatically.
¾ Channel list：Displays the radio channel after the entire search, the
channel can be selected through up and down keys and then press the
middle button to listen to radio channels directly.
In "Channel List" screen, press the [Option] to enter the following menus:
Play: Listen to the selected radio channel.
Edit: You can edit the "station name" and″ "frequency”.
¾ Save: The radio channels which searched manually will be
saved.automaticly.
¾ Manual search: Enter the desired radio channel directly to search.
¾ Open/Close speaker: Play the radio through speaker.
¾ Backgroud play: This setting allows that after exiting the radio interface,
you can continue to listen to the radio. Pull out the headset and then
radio play will be exited directly.
¾ Help: It provides the help information.
43
Page 44
8. Message
Message is the network service, wether the menu can run or not is
connected with the type of your SIM card and the network operators. Please
make sure this function of service before using this feature.
8.1 Write message
Before using this feature, you must obtain the appropriate service center
number from the network operators. The capacity of the SIM card memory
is based on the type of different card.
8.1.1 New SMS
Each of the text messages can contain up to 268 Chinese characters or
612 English characters.
In the standby state, press the middle button to access the main menu
and then select [Message →Write message →New SMS] to enter the
editing interface.
When you have finished editing text message, select <option> will appear
menus as follows:
44
Page 45
¾ Send: After inputting the destination number or pressing the left soft key
to enter the necessary record through the contacts, you can send out
message.
¾ Insert template: Insert templates into the text at the position where the
cursor is on.
¾ Contact info: You can extract name and phone number from the contacts
and then insert it into the message content.
¾ Add phiz: Insert emotion icons into the text in the cursor position.
¾ Save: Save the edited message to the Drafts.
8.1.2 New MMS
MMS is the multimedia information which supports pictures in the format
of GIF, JPEG, WBMP and BMP.
Note:
You can use this function only when the network operator supports it.
And only the mobile phone with MMS function can receive and display
properly.
In the standby state, press the middle button to access the main menu,
then select [Message → Wrire message → New MMS] to enter [MMS
Option] interface.
45
Page 46
¾ Send: Send the edited MMS to the objective number. Before selectting
the menu, you must set up the recipients ' number in advance.
¾ To: Add the recipients’ number by [add recipient] or [Add Group]; you can
also edit or modify the existing recipients.
¾ Cc: You can Cc the MMS to the designated number of the recipients.
¾ Bcc: All the recipients and the Cc recipients can not see the number of
Bcc recipients after receiving this MMS.
¾ Edit title: Edit the content of MMS title.
¾ Edit content: Edit the MMS’s content. Select the <option>, it provides as
follows:
Edit text: Edit the text content of the current MMS.
Insert：
z Insert slide: You can insert a new page; the inserting pages
are up to 20.
z Insert picture: You can select the required image with the
format of WBMP, BMP, GIF or JPEG.
z Insert sound: You can select audio files with the format of
MIDI, WAV, MP3 or AMR to insert in the current MMS.
z Insert video: Add video files with the format of 3GP or MP4 to
insert.
Delete：
46
Page 47
z Delete picture: Delete the current picture (the option will
appear after insertting a picture into current page).
z Delete sound: Delete the current sound (the option will appear
after insertting a sound file into current page).
z Delete video: Delete the current video (the option will appear
after insertting an video file into current page).
z Delete slide: Delete the current page。
Previous slide: Navigate back to the previous page from the
current page (this function will appear when there is more than
one page in the MMS).
Next slide: Navigate to the next page from the current page (this
function will appear when there is more than one page in the
MMS).
Set slide time: Set the play time for the current page, the effective
time is1-600 (seconds).
¾ Preview: Preview each page in turn.
¾ Save: Save the MMS to the [Drafts] to the re-edit or re-send.
¾ Set send on time: You can set the edited MMS to be sent at a specified
time.
47
Page 48
8.2 Inbox
Store the received SMS and MMS.
8.3 Outbox
Save the SMS and MMS which send out failed.
8.4 Draftbox
Save the SMS and MMS which are not sent out.
8.5 Sentbox
Save the SMS and MMS which you sent out successfully. If you want to
save the messages which you sent out automatically, you need select
[Message → Option] and set it under [Settings → SMS sent messages
stored].
8.6 Message settings
In the standby state, press the middle key to access the main menu and
select [Message→ Option] to open the message settings menu.
48
Page 49
8.6.1 Template SMS
The default message in the Templates can be used directly when writing
SMS. By editing, you can self-set up five common template messages.
8.6.2 Voice mail
This feature is similar to the answering machine, with which you can
thansfer the missed call to your own proprietary voice mail, it means let the
caller leave an oral message and to notify that you have oral messages in
voice mail messages via SMS. This feature is part of the supporting
software from network operators to users, so you need register the business,
and set manually. Please contact your network operator for more details.
Note:
By setting the "call forwarding" feature, the voice calls can be
transferred to voice mail (the caller's number for leaving message).
Select the type of SIM card, the provision is as follows:
¾ Line 1 number /Line 2 number:
Retireve message: If the number is empty, you must enter the
requested mailbox number to listen to the receiver’s leaving
message.
49
Page 50
Number settings: Enter (or modify the existing) the voice mailbox
number obtained from the network operator's.
¾ Fax number
The related operations are similar to "voice number". It is determined
by the network operators, it is not supported in the domestic state
currently but the foreign supports for this business!
¾ Data number
The related operations are similar to "voice number". It is determined
by the network operators, it is not supported in the domestic state
currently but the foreign supports for this business!
8.6.3 Cell broadcast
Web services allow you to receive text messages of various contents,
such as news, weather and traffic information and so on. Contact your
network operator for more information.
¾ Read: Read the broadcast messages received by phone.
¾ Startup: You can choose [Open] or [Close]. If you select [Close], then
regardless of whether the channel has been set to the corresponding
number, the phone can not receive any broadcast messages.
¾ Channel: You can select [Add Channel] or [channel list] to operate.
¾ Language: The phone provides you with multiple languages, with
which you can choose to listen to the broadcast.
50
Page 51
8.6.4 SMS settings
¾ SIM1 / SIM2 msg counter: When you send out text messages, you
must set the service center number of network operator. You can also
obtain the number from the network operators. Most of the SIM cards
have already contain the service center number.
Note:
If you modify or delete the message center number, you might not send
out text messages.
¾ Message validity period: You can set the validity period of SMS stored
in the information center as 1 hour, 6 hours, 24 hours, 72 hours, a
week or max.
¾ Status report: Select [Open] and then the information center will
prompt you when you send out text messages successfully.
¾ Save sent messages: Set the state of Save sent messages as Prompt, Save
or Not save.
¾ Prior storage medium: Choose the preferred place to store the MMS.
8.6.5 MMS settings
¾ SIM1 / SIM2 MMS account: Select the MMS account for SIM1 and
SIM2.
¾ Arrive report: Open this function and then the network will send a
message to inform you when the receiver has received and
download the multimedia message you send; you can also choose
[Close].
51
Page 52
¾ Read report: Select [Open], then when the receiver read the
multimedia message, the network will send the read report to you;
you can choose [Close].
¾ Anonymous: Select [Open], the MMS can be sent to the designated
receiver without displaying the sender number.
¾ Pirority: Set the priority level of MMS.
¾ Receive MMS: The phone provides you with [Manual receiver] and
[Auto Receive]. If you select [Manual receiver], you need the
download the MMS in inbox manually; if you open [Auto Receive],
the received MMS will be downloaded automatically each time when
the phone return to the standby state.
¾ Play sound: With opening about this function, the sound of the MMS
can be played when you view it.
¾ Adversting: With opening, the phone can receive advertising while it
is receiving MMS.
¾ Message validity period: You can set the validity period of the MMS as 12
days, 1 day, 1 week or maximum.
Note: The maximum time is connected with the services supported
by the network operator.
¾ Storage location: Choose the storing place for the pictures, music and
video files in MMS.
¾ Restore to default: Restore the default settings of MMS.
8.6.6 Message memory
Using this feature can query the use status of SMS and the capacity
usage of each MMS mailbox.
52
Page 53
9. Tools
9.1 Alarm
In the standby state, press the middle button to access the main menu
and select the [Tools → Alarm], you can set the name, time, tone and repeat
mode for alarm.
The phone has three alarm clocks, which can be open simultaneously.
Each alarm can be set as single reminder, daily reminder or weekly
reminder.
9.2 Calendar
In the standby state, press the middle button to access the main menu,
and then select the [Tools → calendar].
Get into the calendar interface, you can nacigaiton keys to view different
solar calendar and the bottom of the screen displays the corresponding
lunar calendar.
Enter [Option] to carry on the following operations:
¾ New schedule: Create a new calendar reminder, the default time is the
date which the focus on in the calendar.
¾ View schedule: Check whether there be any calendar reminder in the
date the focus is on.
¾ All schedules: See the all schedule remind records.
¾ Clear today calendar: Clear the reminder in which date the focus is on.
53
Page 54
¾ Clear all: Clear the all schedule reminders.
¾ Go to date: Query the calendar information according to the inputting
date.
¾ By week / month: Set display mode of the calendar.
9.3 Calculator
The calculator provides you with four basic functions, by which you can
carry on simple operation for your convenience. Select the calculator, the
calculator interface is showed:
Input data directly by pressing the keyboard
Press the "*" key for a decimal point (.); Press the "#" key to make the
numbers switch between in the positive and negative.
Using the navigation keys to select the appropriate icon in the interface to
carry on the operation of ＋, －, × and ÷.
Short press the right soft key can clear the last bit of input or result; long
press the right soft key to clear all of the input or the result (when there is no
input value, press the button to exit calculator).
Press the middle button to get the result.
Note:
This calculator has limited accuracy, with which the calculator will have
round-off errors, especially when in addition to endless.
9.4 Recorder
In the standby state, press the middle button to access the main menu
54
Page 55
and then select [Tools → Option →Recorder → Start to record] to starting
recording, or use the middle button to select the icon in the interface to
start recording. Select the icon to pause; select the icon or press the
right soft key to select [Stop] to stop recording. After choosing to stop
recording, the audio file will be saved automatically in the folder of "Audio"
exited in memory card, you can choose the icon to view it in the [Option
→ Record file list].
After recording, press [option] to enter the following menus:
¾ Audition: Listen to selected recording file.
¾ Record again: Record the file again.
¾ Delete: Delete the selected recording file.
¾ Send: Send the selected recording file via MMS or Bluetooth.
¾ Record file list: Browse all the recorded audio files.
9.5 World time
Press Left/Right key to display the current world time; enter Options to set
the current world time as local or daylight saving time.
9.6 STK
Get into the STK submenu and you can use the value-added services
provided by the network operators.
55
Page 56
The phone supports the STK function, but this service provided by the
network operator. If the SIM card and the network operators do not support
that kind of service, this feature will not be used. For more information,
please contact your network operator.
56
Page 57
10. Pastime
10.1 Picture Brower
This feature is convenient for users to browse photos and images stored
in the phone quickly.
In the interface of "Picture browser", press the middle button to preview
the selected image; press [Option] can operate the following functions:
¾ Change folder: Set the default image browsing path for "Image browser".
¾ Send: The selected picture can be sent out through MMS or Bluetooth.：
¾ Slide play: View the image in slide way with full-screen.
¾ Delete: Delete the selected picture.
¾ Set as wallpaper: Set the selected picture as wallpaper showed in the
main interface.
¾ Rename Change the name of the
¾ Mark: Mark, Unmark, Mark all or Unmark all to the selected picture.
¾ Detail: See details about the selected picture.
¾ Slide settings: Change the slide show effects by setting "selection effect"
and "slide delay".
57
Page 58
10.2 EBook
The E-book reader supports browsering the TXT format files, you can
copy files from PC to the [Ebook] folder in T-FLASH card. In the standby
state, press the middle button to access the main menu and then select
[Entertainment → E-book] to enter it.
In the interface of E-book list, press the middle button to read these
E-books directly. In the e-book reading interface, press [Option] to access
the appropriate Option:
¾ Add bookmark: You can add the contents in the current page of the
e-books to bookmark for later reading. The bookmarks for each
E-book are up to 50.
¾ View bookmark: View the contents of all the bookmarks which have
been added.
¾ Jump first page: Jump to the first page to read directly.
¾ Jump last page: Jump to the last page to read directly.
¾ Jump page: Enter the page you need jump to, then then the E-book
reader will jump to the confirmative page.
¾ Ture on/off backlight: Always choose to open or cancel the backlight
function.
Description:
If the reader interface prompts the space is not enough when you
browse the E-Book files, please delete the unwanted files to ensure that
the phone has more than 500KB of free space.
58
Page 59
In the e-book folders, select a document and press [Option] to access the
appropriate Option:
¾ Detail: View the details of the selected E-book for date, time, size,
location and other information.
¾ Last read books: Check the E-books which you have readed recently.
¾ Send with BT: Send the selected documents of E-book to others via
Bluetooth.
¾ Delete: To delete the selected document of E-book.
¾ Mark：
Mark: When the selected file is not marked, this menu is effective.
After choose this feature, it will make a mark to the current file.
Cancel mark: When the selected file is marked, this menu is
effective. After choose this feature, it will cancel the mark to the
current file.
Mark all: When there be at least one file is unmarked, this menu is
effective. After choose this feature, it will make marks to all files.
Mark all mark: When there be at least one file is marked, this menu
is effective. After choose this feature, it will cancel the marks to all
files.
¾ Settings：
Browse page mode: You can select "Full page" or "Reserve last line".
Color: Change the “Font color” and the “Backgroud color”.
59
Page 60
10.3 Boxman
Push all the boxes to the specified destination can cross the border. Use
the up / down keys or the right / left keys to move the porters to free space;
select the "Return" can exit out of the game interface.
60
Page 61
11. File list
You can edit the folders in the U disk or in the memory card.
These files below are used as follows:
¾ My music: Store the audio files. It can store the recording files with
the wav format; Mp3, midi, amr and aac can be stored, too.
¾ Ebook: Store the electronic documents. It can store up to 500 books
and the maximum limit for each is 5M.
¾ Photos: Store the image files. The the image format which can be
previewing includes jpg, gif, bmp and wbmp. You can check it
through the "Photo Manager". The image of JPG format is up to
1.2M and the image of other formats is up to 100K.
¾ Videos: Store the video files.It may be used to store the avi files, mp4
files and 3gp files.
¾ vCard: Storage the card files with the vcf format. In the contacts,
copy one contact to memory and then this record will be saved in this
folder in the vcf format.
Note:
The five folders above are protected, they can only be read and read,
and you can not delete or rename them.
61
Page 62
In file list, press [Option] to get into the following menus:
¾ New folder: Create a new folder in the selected directory.
¾ Delete: Delete the selected file or folder.
¾ Detail: View the details of the folder or file.
¾ Edit: You can set the operations of "Rename" and "copy".
¾ Search: Search all the files in the memory card according to
user-defined.
¾ Sort: Sort the files according to "name", "date", "size" or "type".
¾ Mark: Carry on these operations, such as Mark, Unmark, Mark all
and Unmark all, to the selected file or folder.
¾ Memory status: Query the status of the memory and select “Format” to
format the memory.
62
Page 63
12. Settings
12.1 Call settings
12.1.1 Dual-SIM
¾ Set dual sys call forward
Use this function, please set the machine number at frist.
You can set the dual-card call transfer between each other, before using this
feature, please select [Settings →Dual-SIM→ Dual SIM settings] and enter two
SIM cards’ number.
¾ SIM enable select
You can choose standby mode for SIM card. You can choose one of them: Only
SIM1 enable, Only SIM2 enable or Dual SIM dual standby.
¾ Main SIM settings
It can be divided into the following categories:
Communication Class
For Call, SMS, MMS and Internet, you can select the SIM card type according
to your need, you can also choose to give prompt selection when you use one
function.
Prompt dial
After setting, the phone will use the SIM card you have set in advance to make
the speed dial.
Original SIM reply
63
Page 64
You can set to return the calls, SMS, MMS and using the internet by the current
SIM card.
Note:
The priority of "Reply by original SIM" is higher than the "Dual SIM
settings".
¾ Set SIM name
You can customize the name of the SIM slot.
¾ Dual SIM settings wizard
You can set the function of Dual SIM dual standby according to the prompt steps
in accordance with the interface.
¾ Help
Provide correclative information of help.
12.1.2 Network settings
The phone offers [Auto Select] and [Manual select] for you.
¾ Auto select: the phone will search for and register the available
networks automatically.
¾ Manul select: the phone will search for the web after selecting this
menu and the networks which are found will b listed and the user can
choose which network to register.
64
Page 65
12.1.3 Divert calls
According to the conditions you have set for transfer, the incoming calls
will be transferred to voice mail or the appointed number in the appropriate
conditions.
¾
Unconditional:
voice mail or
¾
If busy:
mail or
the appointed number when your cellphone is busy with other
After open this function, any call to you will be transfered to
After open this function, any call to you will be transfered to
the appointed number under any condition.
voice
functions.
¾
If no answer:
will be transferd to
¾
If unreachable:
will be transferrd to
After open this function, any call to you that isn't replied directly
voice mail or
the appointed number.
After open this function, any call that cannot reach you directly
voice mail or
the appointed number.
You can choose Activated, Off or Query status for each of these. Select [Query
status] to view the current state of the corresponding transfer services.
¾
Cancel all diverts:
Cancel all the call transfers.
12.1.4 Restrict calls
This feature allows you to restrict the phone call or answer an incoming
call.
Select the desired limit entry, access "Confirm”, then you can carry on the
operations of Activated, Off or Query status. Select [Open], then the phone
65
Page 66
will ask the network to deal with current settings. The call barring Option
provided for you are as follows:
Option Description
All outgoing calls
Limit all outgoing calls to any phone.
All incoming calls All calls are limited to dial this phone.
Incoming when
roaming
All intl outgoing
Outgoing intl
roaming
Cancel all barring
Change password
Roaming calls can be not answered when
roaming.
International outgoing calls are prohibited.
The international roaming call is limite when
you are in international roaming.
Cancel all call barring.
Modify password of the call barring.
Note:
Some network operators restrict the use about this function, please
contact the network operator to consultate. When you apply for this
service, your network operators will provide you with the initial network
password.
12.1.5 Call waiting
¾ Activated: After activating it successfully, a new call coming in when you
are answering one call, the network will notify you of the new call. You
can maintain a current phone to answer another call.
¾ Off: Close call waiting service.A new call coming in when you are
answering one call, you will not be able to receive the call.
¾ Check status: To view the current status of call waiting service.
66
Page 67
12.1.6 Hide ID (Requires the network to support)
¾ Hide ID: The receiver hide your phone number when you make a call.
¾ Display ID: The receiver will show your number when you are dialing.
¾ Display ID by network: The network will decide whether the receiver can
show your phone number while you are dailing.
12.1.7 Line selection
You can choose Line 1 or Line 2.
¾ Line 1: You can answer or make calls.
¾ Line 2: Select this option, whether you can make a call is depended on
the network operator.
12.1.8 Fly mode
¾ Activate: Start the flight mode immediately. The phone will turn off all the
network services. When you are riding a plane, you’d better open this
mode.
¾ Selcet when power on: When turn on your phone, the prompt whether to
open the flight mode is gived.
12.1.9 Others
¾ IP number
67
Page 68
Activate the feature, choose to [IP call] when you dialing up, or enter the
number in the standby state, then press the middle ke y, with which can add
the IP number before the dialing phone number automatically.
¾ 50 secs warning
If you open it, the mobile phone will give "beep" sound to prompt after the
first 50 seconds of every minute, by whitch you can end the call in time to
save cost.
¾ Connect prompt
Open it and then the phone will have the vibration prompt after the
receiver answer the phone when you are dialing.
¾ Magic voice
Activate or deactivate this function. When you open it, you need set the
magic voice effect when you make a call or answer a call every time.
¾ Any key / Reject mode
SMS reply after reject: Choose whether reply SMS when you refuse
one call.
Any key answer: Press any key on the keyboard to answer the call
except the Hung_Up key and the Right soft key.
¾ Auto redial
Open it and then the phone will redial the number automatically when you
make a failed call.
68
Page 69
12.2 Phone
12.2.1 Time and date
You can also set the time format and date format.
¾ Set time：Press the up/down keys and the left/right keys to set the current
time.
¾ Set date：Press the up/down keys and the left/right keys to set the current
date.
¾ Time display type：Set the time format as 12 hour or 24 hour.
¾ Date display type：Set the date format as "year-mouth-day", "month - day
- year" or "day - month - year.".
12.2.2 Language
There are two languages you can choose: English and Chinese.
12.2.3 Input modes
Chinese fuzzy sound settings: You can make 10 kinds of Chinese Fuzzy
audio settings. The choosing method is multiple choices, with which you can
open several fuzzy sound.
12.2.4 Set shortcut
With this setting you can change the shortcut functions corresponding to
the left / right soft key and the shortcut icon on the main interface in standby
69
Page 70
mode.
12.2.5 Auto power on / off
You can set the phone power on / off automaticly. The setting method is
the same as alarm.
12.2.6 Power management
Show the power of the battery.
12.2.7 Restore factory settings
Reset the parameter value of the mobile phone, with which can make
your phone reset to default settings. Please enter the privacy password (the
initial password is 1234) to restore factory settings.
12.3 2D setting
The phone has the feature of 2D sensor, with which you can achieve the
switching function to change music, wallpaper or picture.
12.4 Display
12.4.1 Wallpaper settings
Choose picture to be used as wallpaper for your phone.
70
Page 71
12.4.2 Standby style
Choose the style of your standby interface. The phone offers two default
styles: the basic style and smart style.
12.4.3 Set idle display
Select the projects displayed in the standby state, including the time and
date, operators, agenda and individual words. You can edit the individual
words.
12.4.4 Contrast
Set the brightness of the screen backlight.
12.4.5 Backlight
Select the time for screen backlight, including "always open", "30
seconds", "20 seconds", "15 seconds", "10 seconds" and "5 seconds".
12.4.6 Keypad light
Select time for button backlight, including "20 seconds", "10 seconds", "5
seconds", and "night mode" and "off".
71
Page 72
12.4.7 Animation effect
Set the animation effect for powering on or powering off.
12.5 Security
You can use the PIN code, PIN2 code, set the password of powering on
and set the security feature to protect the security for information.
12.5.1 PIN
PIN code (PIN1) is the personal identify number for SIM card. If the user
does not change the original password, the password supplied by the
operator is 1234 or 0000. If you activate the PIN code for powering on, then
4-digit PIN code is necessary to enter after each start. The PIN code can be
amended, which used to protect your SIM card is not used by others.
Please note that if the PIN code input wrong for three times continuously,
the phone card will lock automatically and prompts you to enter PUK code to
unlock it, at which time you are close to the brink of danger. Therefore, if you
modify the PIN code by yourself, make sure remember it in mind.
PUK code (PUK1) is ordered by the 8-bit numbers and the user can not
change it. When the PIN code is locked and when the phone prompt you to
enter the PUK code, do not act rashly, because the opportunities for
0inputting the PUK code is only 10 times and it you enter the wrong words
72
Page 73
for 10 times continuously, the SIM card will be locked permanently, that
means it is scrapped. The PUK code for some the SIM card is incidental
with the SIM card, such as China Mobile's Shenzhouxing, etc, while the
others need the network operators to obtain the PIN code. If your PUK code
is locked and you do not know it, do not random input. The correct way is to
call the hotline operators the SIM card belongs to. After verifying the simple
user data, you can obtain the PUK code to unlock the phone. This service is
free of charge.
Warning:
Please use this feature with caution and if you forget the PUK password,
please contact the network operator. If 10 consecutive PUK code be
inputted in error, the SIM card will be scrapped.
After selecting the SIM card type you want to set, you can carry on the
operations as follows:
Open: Activate it and then you need to enter the PIN code each time
you open phone.
Review: You must open the PIN code before you change the PIN
code.
Close: Close the PIN code must″ enter the correct PIN code.
73
Page 74
12.5.2 PIN2
PIN2 code (PersonalIdentificationNumber2) is entered when you enter a
particular function (such as setting a fixed number, set the call billing, etc.).
PIN2 code is entered when a particular feature is used, such as the
elimination for call cost information, set the unit for currency, to achieve cost
limit function, limit to dial and so on. The PIN2 code provided by the supplier
as another SIM card password, please contact your network provider to
access PIN2 code.
When entered the wrong PIN2 code for 3 times continuously, the phone
card will be locked, then you must enter the correct code to unlock PUK2.
Warning:
Please use this feature with caution, if 10 consecutive PUK2 code input is
error, SIM card will be scrapped.
12.5.3 Privacy protect
This function can protect your phone's specific features to prevent
unauthorized viewing by others. When activate password protection feature
for call records, messages, camera, Contacts, document management,
e-book, calendar, U disk, etc, you need enter the correct password after
entry the corresponding main menu or submenus. The default password is
"1234", you can also modify the password.
74
Page 75
12.5.4 Auto key
You can select 5 seconds, 15 seconds, 30 seconds, 1 minute or 5
minutes to open the automatic keylock function; you can also select [Close]
to close this function. When this feature is turned on, the automatic
keyboard lock feature is started to prevent misuse.
¾ The operation of locking the keyboard manually is: In the standby state,
press the Left soft key and then press the * key.
¾ The operation of unlocking the keyboard manually is: In the interface of
keyboard has been locked, press the Left soft key and then press the *
key.
12.5.5 Red key locks keypad
You can choose to enable or disable this feature. Open this feature, you
can just press the Hung_Up key to turn off the backlight and lock the
keyboard automatically when the phone screen is bright.
12.5.6 Power-on PWD
This function need set a password (the password length is 4-8) when you
use it for the first time. When you start the feature, each time requires a
password when you open you phone. You can also change the boot
75
Page 76
password or turn off this function.
Description:
There is no limit for the number of inputting the power-on password.
Please remember this password in your heart, or if you forget it, it will not
be turned on successfully for the next time.
12.5.7 Theft proof
Theft proof feature (MSD) is also known as mobile dog. Its main function is
to collect the current CELL ID (mean: cell ID) and other information sent to
the pre-specified phone at the time when the phone is used illegally. To a
certain time or after certain times of making the phone power on, this
function will prevent others from re-booting to use this phone.
The theft proof function is off by default, and you need change your
password before activating it. After activating it, you need enter a password
to carry on the operations for startupping, shutdowning or changing your
password. The password has the six bits. In addition to a password, a
pre-designated phone number is also required to enter (cell phone stolen,
the mobile phone number to receive notification messages) to open this
function.
When you activate this function, the mobile phone will store the SIM
card's IMSI number. As this number is only, when another SIM card is
76
Page 77
inserted, there will be a prompt box appeared to ask you to input the theft
proof password if the phone is powering on. If you enter the wrong
password for three times, or to opt out of interface, the phone will take it as
illegal use, and gives an prompt of illegal use, and then the phone will read
the CELL ID, LAC (means: location area code, used to identify the different
location of areas), MCC (means: Country Code for Mobile. "460" is the MCC
of China), MNC, MCN and other information, to send text messages to
pre-designated phone number. Legitimate users can get this message to
report to the public security organs, with which can be used to check the
illegal use of the phone (including the location of the region when the mobile
phone is used, communication records, etc.).
If sending fails or is on at this time, the sending text messages will be sent
the next minute, until send them successfully. Over 24 hours in the standby
state or reboot the phone, the phone will send a text message to your
pre-specified mobile phone number again. Send text messages
successfully to a certain number of times (15 times), any use of an illegal
SIM card can not use the machine, the phone will shut down automatically.
Note:
If your phone is stolen, please report to the public security organs, but it
can not ensure that the phone must be able to recover, so please keep
your personal belongings carefully.
77
Page 78
If the phone takes this SIM card as illegal card and you want to open the
anti-theft function, the phone will prompt you have no right to use, it
means you can not use the security features of the corresponding menu
under Theft proof. If the phone is switched on using another card and the
password is entered correctly, the the message count for sending will start
counting from 0 and the phone will prompt whether binding. Select binding,
the phone will update and use this SIM's IMSI number information, then
this card is treated as the specified card of the phone.
¾ Activate: To enable this feature, you must first set a password, if the
password is not set, the phone prompts that "Please change your
password". You can get into the [Change Password] menu to set the
security password and then open this function. The security
password and notification phone number are requested to enter (to
receive the illegal use of the mobile phone SIM card to send on this
illegal SIM card information) to open it.After these steps, anti-theft
feature is activated.
¾ Deactivate: Turn off anti-theft feature. You must first enter the
security code to close it.
¾ Modify PWD: Modify the security password.
Warning:
Please use this carefully. If you forgot your password, you can not use
the phone.
12.6 Profiles
Through this menu, you can set different profiles to suit different
78
Page 79
environments. The phone has 5 profiles: Standard, Silent, Vibrate, Low ring
and High ring and vibrate mode. Each model has the default value, and you
can set up according to your need.
Press the left soft key to select "Option", the menus is as follows:
¾ Activate: Start the selected profile.
¾ Settings: You can set all kinds of effects to your own need.
Ring set: You can set the ring tone about incoming calls and
messages.
Ajust volume: You can set the volume of ringtone about incoming
call, new message, communicate, alarm and power on/off. Please
press the left / right key or the up / down key to adjust the volume.
Call alert: Set the alert mode for incoming calls.
Message alert: Set the alert mode for new messages.
Alarm remind: Set the alert mode for alarm reminding.
Keypad tones: Set the sound effect of key tone as silent, ring 1 or
ring 2.
Battery low alert: You can set whether to open the low voltage
warning tone.
Power on / off tone: You can open or close the ringtone when the
phone is switched on / off.
¾ Rename: Modify the name of the profiles.
¾ Enhance ring: Open or close the function fo enhancing sound.
79
Page 80
12.7 Link
12.7.1 Bluetooth
¾ Open /Close bluetooth: You can open or close your bluetooth device.
¾ Bluetooth visibility: Set to show or hide the Bluetooth device of your
phone. When set to hide it, the external phone can not search for
your Bluetooth device even you Bluetooth have been turned on.
¾ Paired device: Search for nearby Bluetooth devices which have
enabled.
¾ Set shared files
Directory sharing authority: It can be set to “Full control” or “Read
only”.
Sharing directory: Select the "memery card only" to share the
memory card to another person; select "Select Directory" to share
the custom directory to others.
¾ My Bluetooth name: The display name of your Bluetooth when other
people’s devices have found your device after your Bluetooth is
turned on.
¾ Bluetooth file location: Select "Only memory card" to store the
received files via Bluetooth to the memory card.
¾ Help: Provides help information related to Bluetooth.
12.7.2 Network accout
80
Page 81
You can choose the network account according by yourself. China Mobile
GPRS, China Mobile MMS and China Unicom WAP are the three default
account in your phone and you can not delete or edit these three accounts.
You can also add your own network accounts.
In the interface of Internet, press [Options] can carry on the following
operations:
¾ Build a new link setting: Create new accouts through this menu.
Security connect setting: Open or close the function of security by
yourself.
User name: Free to edit the user name for network.
Password: Set the connection password.
APN: Set the name of network access point.
Gateway IP address: Set the address of the network IP.
Port: Set the network port.
Rename: Free to edit the account name.
Set homepage: Set the homepage address.
Advanced settings: You can set the DNS address and the network
type.
¾ Add a new link setting list You can choose to add the default Internet
accounts more than one.
¾ Search: Search for the registered network configuration in the nearby
area, and they can be used directly after searching.
81
Page 82
¾ Delete a setting list: Delete the selected Internet account.
¾ Edit: Edit the selected Internet account.
12.8 Torch
Open or close the torch; view the help imformation.
Long press OK key in standby state to open or close the torch.
82
Page 83
13. Additional features
13.1 The function of U disk
Follow these steps to use the U disk:
¾ Before use, make sure the system of your computer is Windows2000 or
WindowsXP.
¾ Connect the computer with your phone by USB data cable provided with
the phone properly.
¾ After the phone is connected with the computer, select [U Disk] in the
phone. When the computer identifies the U disk successfully, the status
bar will appear a small green icon of the USB device in the lower right
corner of the phone.
¾ Open "My Computer"and you can see the "Removable Disk", then the
operation to U disk can be carried out.
¾ The multimedia files, which you browse through the mobile phone, must
be stored in the specified directory to identify, or it will be not read or play
through the phone if they are stored on the other directory. For example
the image files only in the "Photos" directory can be readed through the
phone.
83
Page 84
Note:
1. When the the phone is used in the state of U disk, you can see some
default application files, and once you remove them, the default files will
be lost permanently.
2. After using the U disk, at first remove the U disk from the computer
equipment and get the notice from system, and then you can pull U disk
safely, otherwise it will make data loss easily, even lead to the damage of
U disk file system.
3. To support USB1.1.
84
Page 85
14. Phone maintenance
Mobile phone is an electronic product with high-precision, please maintain
it carefully. The following suggestions can help you to maintain phoneand
extend the lifespan of it:
¾ The phone and its accessories should be placed out of the reach of
children.
¾ Keep the device dry. Rain, humidity or moisture will corrode the circuit
board. If the phone is flooded accidentally, you should remove the
battery promptly and sent it to the local authorized service center for
processing immediately.
¾ Do not place your phone in places which are full of dust, or it may affect
the normal use of your phone.
¾ LCD display is the part of phone which can be damaged easily, so you
should avoid dropping the mobile phone onto the ground or making the
phone vibrating strongly; prohibit using sharp objects to touch the
screen.
¾ Do not place the phone where¬ the temperature is too high. High
temperatures can shorten the life of electronic devices, damage
batteries, and warp or melt plastic shell phone.
¾ Do not place the phone where the temperature is too low. Otherwise,
when the temperature of the phone raise to normal temperature,
moisture will be generated internally and it could damage the device of
electronic circuit boards.
85
Page 86
¾ Do not drop, knock or shake the phone severely, so as not to damage
the internal circuit boards and precision mobile structure.
¾ Do not use chemicals, cleaning solvents or strong detergents to clean
the device. You need use the soft cloth soaked in soapy water to scrub
it gently.
¾ Do not use the pigment to paint your phone.It can avoid the moving
parts be stuck, with which can affect the proper operation of your
phone.
¾ Please use clean soft cloth to clean the lens, such as camera lens.
¾ Only the supplied or designated antenna can be used to replace the old
antenna. The use of unauthorized antennas, phone accessories or
modification could damage the device and may violate correlative
regulations about radio devices.
86
Page 87
15. Eliminate the Simple Tr ouble
In the course of using the phone, please consult the following table to
guide the troubleshooting if the unusual circumstances happen; if the
trouble still unresolved, please connect with the designated service center.
15.1 Phone can not switch on
Possible reasons Solution
The time of holding down the
Hung_Up key is short.
The eletricity of the battery
Press the Hung_Up key more than three
seconds.
Please charge it.
runs out.
The installation of battery is
incorrect.
Illegal use leads the phone
Please installe the battery correctly.
Please enter the correct password.
can not turn on.
15.2 Phone be shut down automatically
Possible reasons Solution
Whether the function of
Schedule power on/off is
enabled.
If you do not need the function of
Schedule power on/off, please cancel
it.
The eletricity of the battery
runs out.
Please charge it.
87
Page 88
The battery loose. Please install the battery correctly
following the battery installation
method in the instructions.
Illegal use leads the phone
Please enter the correct password.
can not turn on.
15.3 PIN/PUK Lock
Possible reasons Solution
PIN (Personal Identification
Please enter the correct password
Number) / PUK code (unlock
PIN) entered incorrectly.
Note:
1. If you enter the wrong PIN code 3 times continuously, the SIM card and
phone's many features will be locked.
2. Can not guarantee the correct PIN and PUK code, please contact the
operator or retailer.
15.4 Poor quality for calling
Possible reasons Solution
The current signal strength
is saltating.
You may be in high-speed moving
state (by train or car, etc.). You can
check the signal strength and select
the place with high signal strength to
ensure call quality.
In the reception with poor
Please go to the open space area.
signal.
88
Page 89
15.5 Can not receive calls
Possible reasons Solution
Open the function of Call
divert.
Open the function of Call
barring.
15.6 Can not make calls
Possible reasons Solution
The phone is turned off.
Not in the network service
area.
Not insert the appropriate
SIM card properly.
Please cancel this function according to
your need.
Please cancel this function according to
your need.
Please turn on it.
Please make sure the network is in
normal service state.
Please make sure your SIM card can
work properly.
Open the function of Call
barring.
Lock the keyboard
automatically.
15.7 Call volume is small
Possible reasons Solution
The call volume is set too
low.
Please cancel this function according to
your need.
Please press the left soft key and the #
key to unlock the keypad.
Please adjust call volume loud.
89
Page 90
15.8 The opposing party can not hear your voice
Possible reasons Solution
The microphone is too far
away from the sound
Please make the microphone near
your mouth.
source.
15.9 Phone does not ring with incoming call
Possible reasons Solution
Incoming call alert is set to
Please reset the prompt for ring.
mute.
Ring volume is set too low. Increase the volume tip.
Open the function of Call
barring.
Please cancel this function according to
your need.
15.10 Battery can not charge
Possible reasons Solution
Battery runs out and be
placed too long.
The connection between
the battery and the phone
is bad.
Poor connection between
the charger and the phone.
Battery or charger is
damaged.
Ambient temperature is too
low or too high.
Please charge it in time after the prompt
of low power is showed.
Please ensure that the battery is
installed properly.
Please connect the charger with the
interface of your phone, and then the
charging icon appears in the screen of
the phone.
Please connect whit our designated
contact point for warranty.
Please ensure that the device is
charging in normal temperature.
90
Page 91
15.11 Reveal no network
Possible reasons Solution
SIM card is not installed
Please install the SIM card properly
properly.
according to the installation method
in instructions.
SIM card and the contact of
Please ensure that they are clean.
phone have impurity.
SIM card is invalid. Please check whether the SIM card is
expired.
Network environment is in
Please go to the place where the
the weak field area.
network signal for phone is strong.
15.12 Phone can not detect memory
Possible reasons Solution
Insert the memory card
incorrectly.
Please insert the memery card in right
way according to the instructions.
Memory card is damaged. Please replace the memory card.
15.13 Storage space is not enough
Possible reasons Solution
The MMS takes up too much
storage space.
The history record in
browser takes up too much
storage space.
Please delete some MMS you do not
need to free space.
Please select [Communications →
browser → WAP→ Browser settings
→ Clear cache] to free up space.
91
Page 92
15.14 The Option for PC Camera can not be achieved
Possible reasons Solution
The "PC Camera" menu
does not appear in the
phone after the phone
connected to the computer.
1. Make sure the USB Interface is
intact in the computer.
2. Make sure you are using the
connection cable provided by the
retailers correctly.
92
Page 93
16. Safety Information
16.1 The environment for using
In order to ensure your rational use about the phone and avoid the impact
on you and the environment, please remember to comply with the rules and
regulations when you use the phone anywhere.
Please turn off your cell phone and comply with all safety signs and
instructions in any place where may lead to explosion, such as gas stations,
fuel depots, chemical plants or other place with blasting operations. It may
cause explosion and personal injury if you disobey the relevant
requirements.
The use of phone on airplanes would interfere with the operations of
aircraft flight and bring dangerous. Therefore, please ensure to turn off your
phone before boarding, and make sure the phone is in the state of turning
off or in the Flight mode throughout the flight (this phone has the function of
Schedule power on/off, so please make sure you have turn off this feature in
the entire flight process).
When driving, please place the phone on the special bracket but not put it
in the seat, or in the place where the phone can slide with slam or the brake
of the car. In order to ensure safe driving and avoid traffic accidents, please
do not use the phone during driving. If you must use the phone, make sure
stop the car first and then use the phone.
To avoid the explosion due to the temperature increase of the phone
battery, please make the phone far away from high temperature.
93
Page 94
16.2 Medical equipment
Please turn off your phone when you close to the electronic medical
equipment, with the express provision for the shutdown of phone (such as
pacemakers, hearing aids and other medical equipment). Most medical
equipment can shield the RF signals of phones, but there are some
electronic devices do not have this feature. If you doubt or can not ensure
whether the medical equipments can shield the RF signals, please consult
your doctor or the medical equipment manufacturers.
16.2.1 Pacemaker
Pacemaker manufacturers recommend that maintain the distance
between your phone and the pacemaker at least about 6 inches (15.3cm),
so as not to interfere the pacemakers with phones.
To persons wearing pacemakers:
When your phone is switched on, please ensure that maintain the
distance between the phone and the pacemaker at least 6 inches (or
15.3cm).
Do not place your phone in a breast pocket.
Please use the ear which is not in the same side with the pacemaker.
94
Page 95
Note:
If you suspect the interference is exiting, please switch off your phone
immediately and ask the medical staff timely.
16.2.2 Hearing aids
Phones may cause some interference to hearing aids, so please
contact the manufacturer immediately if the interference is exited.
16.2.3 Emergency Call
As the phone use the radio signals, terrestrial communication networks
and personal setting function like other mobile phones, it can not guarantee
that your phone connections can succeed in all conditions, please do not
just rely on mobile phones to achieve important communications (such as
medical first aid and other matters).
Emergency call
If your phone is turned off, please turn on it and check the network signal
is strong enough.
¾ Enter the local emergency number correctly (such as 120 whith is the
emergency center). Different regions have different emergency
numbers.
¾ Press the Dial key to call.
95
Page 96
Note:
When make an emergency call, please provide all the important information as
accurately as possible. The phone may be the only tool for communication at this
point, so please do not end the call without permission.
16.3 Accessing password
The password protection for mobile phone and SIM cards are available to
prevent they are used illegally.
16.3.1 Password of power-on
With this function, you can prevent the phone be used by others without
your consent. The original password is set when you use this feature for the
first time. Please change the password of power-on as soon as possible
after you use the phone and make sure it is confidential.
16.3.2 PIN
It is the personal identification code, which is the password to protect the
SIM card and can prevent SIM cards be used by others without your
consent. SIM card and PIN code are usually along with providing. After
enabling the password of power-on, you need to enter the password to use
96
Page 97
the phone normally .
Note:
If you input false PIN code for 3 times continuously, SIM card will be
locked.You must input PUK code to unlock it (If you do not have the PUK code,
please contact your network or retail operator to get the PUK code. Please do not
input any other invalid content.)
16.3.3 PIN2
PIN2 is the password which used to realize the special features of the SIM card.
If the network operator provides this number for you, you are required to input it to
enter some features (such as unit, using the fixed dialing, etc.). Usually the PIK2
code supplied with the SIM card. If you input false PIN2 code for 3 times
continuously, PIN2 are locked and then the PUK2 code is required to unlock it.
16.3.4 PUK
Unlock the PIN2 code. Usually the PUK2 code is supplied with the SIM card,
the PUK2 code can change the locked PIN2 code. If you input false PUK2 code for
ten times continuously, you will not be able to use this SIM card, please apply for a
new card to your network operator. PUK2 code cannot be changed, so if you lost it,
please contact your service provider.
97
Page 98
16.4 Precautions for Battery Charging
The mobile phone uses the ithium-ion battery to provide energy, many
tings can affect the time of standby and call time, such as the system
environment, phone setup and so on.
Please use the standard battery and charger supplied by our company.
Damage can be caused if you use the battery or charger which is not
approved by our company and our company wil not responsible for the
consequences.
The power bar in the battery icon on the phone screen starts scrolling if
the phone is powered on.
NOTE:
1. If the battery is completely discharged, the battery icon should appear
after 2 to 3 minutes after charging. Generally, the time for charging is 2 to 5
hours, based on the current state of the phone (if it is switched on or used to
call, etc.) is different.
2. To make sure the new battery can get to the prime performance, please
finish the period of charging and discharging the battery for two to three
times. When you charge for new battery , please charge more than 10 hours
continuous for the frist few times.
98
Page 99
When mobile phone is in charging, please do not use the wet hand to contact the
battery or charger to avoid dangerous. When your phone is charging, you'd better
not use it. After the charging is finished, the battery icon will stop scrolling, and
you can disconnect the phone from the interface of the charger adapter.
16.5 Cautions for using battery
The use circumstance of battery is decided by the network, phone settings and
the use circumstance of the phone, for example, the capacity of 1200 mAh
lithium-ion battery can support calling for 6-8 hours can used about 150-240 hours
if the phone is in the standby state.
Please do not use any damaged batteries to charge.
When you use cell phone near the base station of cellular network, the
consumption of battery is small. So the signal strength of cellular network and the
parameters set by the network operator affect the call time and the standby time
largely.
The charging time depends on the remaining capacity and the type of battery,
and the model of charger. When the battery life shortted obviously, we recommend
that you replace the battery to ensure the performance of your phone.
Please use the batteries and charger provided by our company, otherwise it may
cause exploding. Please cut off the power when you do not use charger. Do not
charge the battery with the charger more than one week, or it will reduce the
99
Page 100
lifetime of the battery when you charge excessivly.
Don't reverse the polatity of the battery between anode and cathode.
Do not put the mobile phone at places with high or low temperature; otherwise it
may reduce the capacity and the lifetime of the battery. Please use the battery under
room temperature as much as possible.
Do not make the battery in short circuit, otherwise it will damage the battery
core or the internal protection circuit of the battery. When you put battery in the
pocket or bag, the metal items (such as coins, pin or pen, etc.) may make the
battery be in short circuit, so please place battery separately and properly.
Do not burn battery or dispose it as ordinary garbage. Please abide the
local environmental policy to avoid the risk of life and the damage to the
environment. You should process and recycle the battery in time.
If the water run into the phone, the battery or other charging device, do
not put it in any heating equipment (such as a dryer, microwave etc.) for
drying. Cell phone or other products may cause fault, even it will cause fire,
expand or explode to the cell phone, the battery or other charging device.
Please follow the relevant instructions to dispose of the useless batteries.
To any direct or indirect damage caused by the error actions which are
described above, our company does not assume any responsibility.
100
Loading...