ZTE A315 Users Manual

Copyrights

used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation.

ZTE Corporation reserves the right to modify technical parameters and specifications in this guide, and promptly correct the contents in the guide that are inconsistent with the latest documents. All modifications shall be compiled in a new version of Quick Start Guide without prior notice.

ZTE Corporation keeps the right to make the final explanation to this guide.

Trademarks

Android is a trademark of Google, Inc. All other trademarks and copyrights remain the property of their

respective owners.

Third-party Applications Statement

During the installation process of some third-party applications, issues of repeated restart or abnormal operation of software might be caused by incompatibility of t he third-party applications rat her than the phone.

Installation of a third-party ROM or non-official operating system might bring security risk and security threats. ZTE Corporation will not be liable for the security threats brought by upgrade of the operating system.

Home key

Back key

Headset jack

Back camera

Getting to Know Your Phone

Receiver

Volume

Power/Rese t

Front camera

Displa

Noise-reduction

MICSpe

USB port

Inserting SIM card and Memory card

Please make sure that the phone is powered off before proceeding.

Charging the Battery

Connect the charger to the phone using a USB cable, and plug the charger into a standard power socket.

Health and safety

FCC Regulations:

This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two condi tions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation betw een the equipment and receiv er.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connect ed.

-Consult the dealer or an experi enc ed radio/TV technician f or hel p. FCC Note: Caution: Changes or modifications not expressly approved by the party

responsible for compliance could void the user‘s authority to operate the equipment.

RF exposure information (SAR) This phone is designed and manufactured not to exceed the emission

limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.

During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the separation of 10 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power out put.

The exposure standard for wireless devices employing a unit of measurement is known as t he Specific Absorption Rate, or SAR.

The SAR limit set by the FCC is 1.6W/kg. This device is complied with SAR for general population /uncontrolled

exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. This device has been tested and meets the FCC RF exposure guidelines when tested with the device directly contacted to the body.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC

RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: SRQ-A315.

For this device, the highest reported SAR value for usage against the head is 0.365 W/kg, for usage near the body is 1.392 W/kg. Simultaneous RF exposure is 1.499W/Kg.

While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirements.

SAR compliance for body-worn operation is based on a separation distance of 10 mm between the unit and the human body. Carry this device at least 10 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body-worn operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of 10 mm between this device and your body.

RF exposure compliance with any body-worn accessory, which contains metal, was not tested and certified, and use such body-worn accessory should be avoided.

Declaration of RoHS compliance

We’re determined to reduce the impact we have on the environment and take responsibility for the earth we live on. So this document allows us to formally declare that the A315, manufactured by ZTE CORPORATION, fully complies with the European Parliament’s RoHS (Restriction of Hazardous Substances) Directive 2002/95/EC, with respect to all the following substances:

(1) Lead (Pb) (2) Mercury (Hg) (3) Cadmium (Cd) (4) Hexavalent Chromium (Cr (VI)) (5) Polybrominated biphenyl (PBB) (6) Polybrominated diphenyl ether (PBDE) Our compliance is witnessed by written declaration from our suppliers.

This confirms that any potential trace contamination levels of the substances listed above are below the maximum level set by EU 2002/95/EC, or are exempt due t o their application.