NS-CLW01 09-0196 ENG.fm Page 1 Monday, March 16, 2009 4:06 PM
User Guide
Weatherband Clock Radio
NS-CLW01
NS-CLW01 09-0196 ENG.fm Page 2 Monday, March 16, 2009 4:06 PM
NS-CLW01 09-0196 ENG.fm Page 3 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01
Weatherband Clock Radio
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting up your weatherband clock radio . . . . . . . . . . . . . . . . . 8
Using your weatherband clock radio . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Legal notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
90-day limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Welcome
Congratulations on your purchase of a high-quality Insignia product.
Your NS-CLW01 represents the state of the art in weatherband clock
radios and is designed for reliable and trouble-free performance.
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
www.insigniaproducts.com
3
NS-CLW01 09-0196 ENG.fm Page 4 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.To prevent fire or shock hazard, do not plug the power cord
into an extension cord, receptacle, or other outlet unless the blades
can be fully inserted to prevent blade exposure. To prevent fire or
shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
apparatus.
• Attachments—Do not use attachments not recommended by
Insignia because they may cause hazards.
• Water and moisture—Do not use your weatherband clock
radio near water. Such as near a bath tub, in a wet basement,
or near a swimming pool.
• Power sources—Use only the type of power source indicated
on the label. If you are not sure of the type of power supply to
your home, consult Insignia Technical Support or your local
power company. For clock radios intended to operate from
battery power or other sources, refer to the operating
instructions.
• Surge protector—We recommend the use of a surge
protector for the AC power connection. Lightning and power
surges ARE NOT covered under warranty for this product.
• Lightning—For added protection for your weatherband clock
radio during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug the AC power cord
from the power outlet. This will prevent damage to your
weatherband clock radio due to lightning and power line
surges.
• Overloading—Do not overload power outlets and extension
cords, because this can result in a risk of fire or electric shock.
4
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 5 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
• Object and liquid entry—Never insert objects of any kind into
your weatherband clock radio through openings, because they
may touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of any
kind on your weatherband clock radio.
• Damage requiring service—Unplug your weatherband clock
radio’s AC power from the power outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled, or objects have fallen into your
weatherband clock radio.
• If your weatherband clock radio has been exposed to rain or
water.
• If your weatherband clock radio does not operate normally
by following the operating instructions. Adjust only those
controls that are covered by the operating instructions,
because incorrect adjustment of other controls may result in
damage and often requires extensive work by a qualified
technician to restore your weatherband clock radio to its
normal operation.
• If your weatherband clock radio has been dropped or
damaged in any way.
• When your weatherband clock radio exhibits a distinct
change in performance.
• Replacement parts—When replacement parts are required,
make sure that the service technician uses replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, injury to persons, or other
hazards.
• Safety check—Upon completion of any service or repairs to
your weatherband clock radio, ask the service technician to
perform routine safety checks to determine that your
weatherband clock radio is in correct operating condition.
To completely disconnect the weatherband clock radio from electric
power, the AC power plug should be disconnected from the AC power
outlet completely.
Features
Package contents:
• Weatherband clock radio
• Outdoor temperature transmitter
• Transmitter mount with mounting screws (3)
• Battery (CR2032 x 1)
•User Guide
www.insigniaproducts.com
5
NS-CLW01 09-0196 ENG.fm Page 6 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
Front panel
16
# Description Function
1 ALARM 1 button Press to set Alarm 1.
2 TIME SET/TEMP
button
3 RADIO ON button Press once to turn the radio on. Press again to turn the radio off.
4 TUNE+ button Press to tune the radio to a higher station.
5 TUNE
6 AM/FM button Press to toggle between the AM band and the FM band.
7 INSTANT
8 SNOOZE/DIMMER
9 ALARM 2 button Press to set Alarm 2.
10 SLEEP button Press to set the sleep timer, which automatically turns off the
11 PRESET MEMORY
12 VOL+ button Press to increase the radio volume.
13 VOL
14 PRESET+ button In radio mode, press to select the next preset station. In
15 PRESET
16 LCD display Displays the current time, temperature, and radio information.
– button Press to tune the radio to a lower station.
WEATHER button
button
button
– button Press to decrease the radio volume.
– button In radio mode, press to select the previous preset station. In
Press and hold for two seconds to set the time. Press and
release to toggle between Fahrenheit and Centigrade
temperature.
Press to go directly to a NOAA weather station.
Press to temporarily turn off the alarm (snooze), when the alarm
is sounding. Press to set the backlight level to high, middle, or
low, when the alarm is off.
radio after the time duration selected. Press repeatedly to select
the duration.
Press to set radio station presets.
memory mode, press to select the preset number for the station.
memory mode, press to select the preset number for the station.
6
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 7 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
LCD display
# Description Function
1 Alarm 1 status
icon
2 Alarm 2 status
icon
3 Main display Shows the current time, radio frequency, sleep time setting, or
4 RADIO Lights when radio is on. AM or FM icons to the right indicate the
5 WEATHER Lights when a weather station is selected.
6 SLEEP Lights when the sleep timer is set.
7 Battery capacity
icon
8 Volume setting Shows the volume setting of the radio.
9 Indoor
temperature
10 MEM icon Indicates a preset is selected.
11 Outdoor
temperature
12 Preset station
number
Indicates the status of Alarm 1. The icon to the right of the status
icon indicates your selection.
• Bell icon–wake to buzzer
• Music note icon–wake to music
• No icon–alarm 1 off
Indicates the status of Alarm 2. The icon to the right of the status
icon indicates your selection.
• Bell icon–wake to buzzer
• Music note icon–wake to music
• No icon–alarm 2 off
alarm ring time.
band selected.
Indicates the battery status.
Shows the indoor temperature in °F or °C.
Shows the outdoor temperature in °F or °C.
Indicates the preset number selected.
www.insigniaproducts.com
7
NS-CLW01 09-0196 ENG.fm Page 8 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
Setting up your weatherband clock radio
Supplying power
Your weatherband clock radio can either be powered by plugging the
radio into an AC power outlet or by installing four AA batteries (not
included).
Plugging in your weatherband clock radio
To plug in your weatherband clock radio:
1 Place your weatherband clock radio in a convenient place and find
an AC power outlet within range of the power cord.
2 Plug the power cord into the AC power outlet.
Caution
To protect your weatherband clock radio during
thunderstorms, unplug the AC power cord from the AC
power outlet.
Installing batteries
In addition to installing four main power batteries to operate your
weatherband clock radio without AC power, you can also install a
backup battery (included) to provide temporary power in case the AC
power fails or the optional main batteries fail. The outside
temperature transmitter also requires two AA batteries (not included)
to operate.
To install main power batteries:
1 Turn your weatherband clock radio around to the back, then open
the door to the battery compartment.
2 Insert four (4) AA batteries (not included) into the battery
compartment. Make sure that you match the + and – symbols on
the batteries with the + and – symbols in the battery compartment.
8
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 9 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
3 Reinstall the battery compartment door and turn your
weatherband clock radio around to the normal operating position.
Caution
Follow these precautions when using batteries in this
device:
• Use only the size and type of batteries specified.
• Make sure that you follow the correct polarity as
indicated in the battery compartment when installing
batteries. Reversed batteries may cause damage to the
clock radio.
• Do not mix different types of batteries together (for
example, alkaline, rechargeable, and carbon zinc), or
semi-used batteries with fresh ones.
• If your clock radio is not to be used for a long period of
time, remove the batteries to prevent damage or injury
from possible battery leakage.
• Do not try to recharge batteries not intended to be
recharged, because they can overheat and rupture.
(Follow battery manufacturer’s directions.)
• Batteries should not be exposed to excessive heat, such
as sunshine, fire, or the like. Dispose of used batteries as
hazardous waste.
To install a backup battery:
1 Unplug your weatherband clock radio, then turn it around to the
back and open the door to the battery compartment.
2 Remove the four AA main batteries (if necessary), then remove
the cover of the backup battery slot by unscrewing it and lifting it
out of the compartment.
Unscrew
backup battery
cover
3 Insert one (1) CR2032 button cell battery (included) into the
battery compartment. Make sure that the + symbol on the battery
is facing up.
www.insigniaproducts.com
9
NS-CLW01 09-0196 ENG.fm Page 10 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
4 Reinstall the backup battery slot cover, then replace the four AA
batteries (if necessary).
5 Close the battery compartment door and turn your weatherband
clock radio around to the normal operating position.
6 Plug in your radio.
To install batteries in the outside temperature transmitter:
1 Open the battery compartment of the outside temperature
transmitter.
2 Install two AA batteries in the battery compartment. Make sure
that you match the + and – symbols on the battery with the + and
– symbols in the battery compartment.
3 Close the battery compartment door.
Mounting the outside temperature transmitter
To mount the outside temperature transmitter:
1 Remove the mounting bracket from the transmitter, if necessary.
2 Place the mounting bracket in the desired location and mark the
location for the three mounting screws with a pencil.
Tip
• We recommend that you mount the transmitter on the North side
of your house, away from sources of heat or cold (such as
windows or vents) and out of direct sunlight or rain.
• The range of the transmitter is 80 ft. (24.4 m) in open space. The
signal will penetrate walls, but the range will be decreased.
Concrete and metal structures will further decrease the range.
• The transmitter should not be mounted on a metal surface or close
to sources of possible interference, such as cordless appliances
and microwave ovens.
• The temperature transmitter should be mounted ver tically to
transmit the signal well.
• The FM antenna should be opened and the direction adjusted to
receive the best signal.
10
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 11 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
3 Start pilot holes for the screws where you marked their location.
4 Screw the mounting bracket onto the mounting location with the
three screws provided. Make sure that the screws are flush with
the bracket.
5 Snap the transmitter into the mounting bracket.
Using your weatherband clock radio
Using the clock and alarm
To set the clock:
1 Press and hold TIME SET/TEMP until the hour blinks on the
display.
2 Press TUNE+ or TUNE– to set the hour.
3 Press TIME SET/TEMP. The minutes blink on the display.
4 Press TUNE+ or TUNE– to set the minutes.
5 Press TIME SET/TEMP to store the setting and return to standby
mode.
www.insigniaproducts.com
11
NS-CLW01 09-0196 ENG.fm Page 12 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
To set the alarm:
Tip
You can set Alarm 1 for weekdays and Alarm 2 for
weekends.
1 Press and hold ALARM 1 (or ALARM 2, depending on the alarm
you want) until the hour blinks.
2 Press TUNE+ or TUNE– to set the hour.
3 Press ALARM 1 (or ALARM 2, depending on the alarm you want).
The minutes blink on the display.
12
4 Press TUNE+ or TUNE- to set the minutes.
5 Press ALARM 1 (or ALARM 2) to store the setting and return to
standby mode.
6 Press ALARM 1 (or ALARM 2) repeatedly to set the alarm mode.
Settings include:
• Wake to buzzer–Bell icon appears to the right of the alarm icon
• Wake to music–Music note icon appears to the right of the
alarm icon
• Alarm off–Alarm icon disappears.
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 13 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
To turn the alarm off:
1 Press any button other than SNOOZE/DIMMER to turn off the
alarm. The alarm will be set for the same time the following day.
2 If you do not want to set the alarm for the next day, press
ALARM 1 or ALARM 2 until the alarm icon disappears from the
display.
To use the snooze:
1 While the alarm is sounding, press SNOOZE/DIMMER. The alarm
turns back on automatically 9 minutes later.
2 To cancel snooze (the alarm will not turn back on), press any
button other than SNOOZE/DIMMER. The alarm will be set for the
same time the following day.
Playing the radio
To play the radio:
1 Press RADIO ON to turn on your weatherband clock radio.
• To select the radio band you want to listen to, press
AM/FM.
• To tune the radio up or down and select the station you
want, press TUNE+ or TUNE–.
• To auto search for stations, press and hold TUNE+ or
TUNE– for more than two seconds.
• To adjust the volume to a comfortable level, press either the
VOL+ or VOL– button.
• To tune to the next preset station, press PRESET+.
• To tune to the previous preset station, press PRESET–.
• To tune to a weather station, press INSTANT WEATHER.
2 Press RADIO ON to turn off the weatherband clock radio.
Setting and using radio presets
To use presets:
1 Press RADIO ON to turn on your weatherband clock radio.
2 Press AM/FM to select the radio band you want to listen to.
3 Press TUNE+ or TUNE– to tune the radio up or down and select
the station you want.
www.insigniaproducts.com
13
NS-CLW01 09-0196 ENG.fm Page 14 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
4 To save the station as a preset, press PRESET MEMORY. “MEM”
and “00” blink on the display.
5 Press PRESET+ or PRESET- to select the preset number you
want to designate for that station.
6 Press PRESET MEMORY again to confirm the setting. The station
is stored in memory.
7 Repeat Steps 3 to 6 to store as many as 10 AM presets and 10
FM presets.
8 To select a preset station, briefly press PRESET+ or PRESET–
repeatedly until you reach the station you want. “MEM” appears on
the display, along with the preset number selected and the station
frequency.
Setting the sleep timer
To set the sleep timer:
1 Press SLEEP once. The “SLEEP” indicator appears in the display,
and “90” appears (blinking) on the display (indicating that the
weatherband clock radio will turn off after 90 minutes).
2 Repeatedly press SLEEP to decrease the sleep timer in 10 minute
increments.
14
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 15 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
3 To cancel the sleep function, repeatedly press SLEEP until “0”
shows on the display.
Accessing a weather channel
To access a weather channel:
1 Press INSTANT WEATHER. “WEATHER” appears on the display
and your weatherband clock radio begins searching NOAA
Weather Broadcasts for the best reception.
2 Press TUNE+ or TUNE- to change weather channels manually.
3 Press RADIO ON to turn off the weather channel.
Adjusting the backlight
To set the backlight level:
1 Make sure the power is connected.
2 Press SNOOZE/DIMMER to set the display backlight to a
comfortable level, except when the alarm is on. Your choices
include High, Middle, or Low.
Selecting the temperature display
To select the temperature display:
• Press TIME SET/TEMP to toggle between °F and °C.
Troubleshooting
Caution
Do not try to repair the clock radio yourself. Doing so will
invalidate your warranty.
Problem Solution
The radio does not turn on
when RADIO ON is pressed
No sound Increase the volume.
Make sure that your radio is plugged into an AC
power outlet or that four AA batteries are installed.
www.insigniaproducts.com
15
NS-CLW01 09-0196 ENG.fm Page 16 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
Problem Solution
The sound has interference Make sure that the radio is not too close to a TV or
The LCD display is too dim Replace the batteries or adjust the backlight.
other appliance.
Specifications
Power supply AC 120V/60Hz (DC 6 V/0.4 A)
FM band 87.5 - 107.9 MHz in 200 KHz steps (USA)
AM band 530 - 1720 KHz in 10 KHz steps (USA)
Weather band Weatherband
Output power 1 Watt
Speaker 2.25” x 1
Operating temp. (Max) 14 - 104°F (-10 - 40°C)
Outdoor -22 -140°F (-30 - 60°C)
Legal notices
FCC warning
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this product is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced technician for help.
Energy Star
As an Energy Star Partner, Insignia has determined that his product or
product models meet the Energy Star guidelines for energy efficiency.
16
®
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 17 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
90-day limited warranty
Insignia Products (“Insignia”) warrants to you, the original purchaser of this new
NS-CLW01 (“Product”), that the Product shall be free of defects in the original
manufacture of the material or workmanship for a period of 90 days from the date of
your purchase of the Product (“Warranty Period”). This Product must be purchased
from an authorized dealer of Insignia brand products and packaged with this warranty
statement. This warranty does not cover refurbished Product. If you notify Insignia
during the Warranty Period of a defect covered by this warranty that requires service,
terms of this warranty apply.
How long does the coverage last?
The Warranty Period lasts for 90 days from the date you purchased the Product. The
purchase date is printed on the receipt you received with the Product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of the material or workmanship
of the Product is determined to be defective by an authorized Insignia repair center or
store personnel, Insignia will (at its sole option): (1) repair the Product with new or
rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable
products or parts. Products and parts replaced under this warranty become the
property of Insignia and are not returned to you. If service of Products or parts are
required after the Warranty Period expires, you must pay all labor and parts charges.
This warranty lasts as long as you own your Insignia Product during the Warranty
Period. Warranty coverage terminates if you sell or otherwise transfer the Product.
How to obtain warranty service?
If you purchased the Product at a retail store location, take your original receipt and the
Product to the store you purchased it from. Make sure that you place the Product in its
original packaging or packaging that provides the same amount of protection as the
original packaging. If you purchased the Product from an online web site, mail your
original receipt and the Product to the address listed on the web site. Make sure that
you put the Product in its original packaging or packaging that provides the same
amount of protection as the original packaging.
To obtain in-home warranty service for a television with a screen 30 inches or larger,
call 1-888-BESTBUY. Call agents will diagnose and correct the issue over the phone or
will have an Insignia-approved repair person dispatched to your home.
Where is the warranty valid?
This warranty is valid only to the original purchaser of the product in the United States,
Canada, and Mexico.
What does the warranty not cover?
This warranty does not cover:
• Customer instruction
• Installation
• Set up adjustments
• Cosmetic damage
• Damage due to acts of God, such as lightning strikes
• Accident
•Misuse
•Abuse
• Negligence
• Commercial use
www.insigniaproducts.com
17
NS-CLW01 09-0196 ENG.fm Page 18 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
• Modification of any part of the Product, including the antenna
• Plasma display panel damaged by static (non-moving) images applied for lengthy
periods (burn-in).
This warranty also does not cover:
• Damage due to incorrect operation or maintenance
• Connection to an incorrect voltage supply
• Attempted repair by anyone other than a facility authorized by Insignia to service
the Product
• Products sold as is or with all faults
• Consumables, such as fuses or batteries
• Products where the factory applied serial number has been altered or removed
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR
EXCLUSIVE REMEDY. INSIGNIA SHALL NOT BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO,
LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST
PROFITS. INSIGNIA PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES
WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES
FOR THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES,
PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR
PROVINCE TO PROVINCE.
Contact Insignia:
For customer service please call 1-877-467-4289
www.insigniaproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645
© 2009 Best Buy Enterprise Services, Inc.
All rights reserved. INSIGNIA is a trademark of Best Buy Enterprise Ser vices, Inc.
Registered in some countries. All other products and brand names are trademarks of
their respective owners.
18
www.insigniaproducts.com
NS-CLW01 09-0196 ENG.fm Page 19 Monday, March 16, 2009 4:06 PM
Insignia NS-CLW01 Weatherband Clock Radio
www.insigniaproducts.com
19
NS-CLW01 09-0196 ENG.fm Page 20 Monday, March 16, 2009 4:06 PM
www.insigniaproducts.com (877) 467-4289
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
All rights reserved. INSIGNIA is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries.
All other products and brand names are trademarks of their respective owners.
© 2009 Best Buy Enterprise Services, Inc.
ENGLISH
09-0196
Loading...